Bolero DressCode 720 E - Washing machine CECOTEC - Free user manual and instructions

USER MANUAL Bolero DressCode 720 E CECOTEC

1. Parts and components 101
2. Before use 101
3. Product installation 102
4. Operation 106
5. Cleaning and maintenance 120
6. Troubleshooting 122
7. Technical specifications 126
8. Disposal of old electrical and electronic appliances 135
9. Technical support and warranty 135
10. Copyright 135

SOMMAIRE

Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users.

• Ensure that the mains voltage matches the voltage specified on the device rating label and that the plug is earthed.
• If the power cord is damaged, it must be replaced by the official Cecotec Technical Support Service or by a similarly qualified person to prevent hazards.
• This appliance is for indoor use only.
• Make sure the device is installed in places where the temperature is above 0^ C .
• The device is not designed for built-in installation.
• Use the hose set supplied with the appliance. Do not reuse old hoses.
• Check hose connections regularly to ensure that no water leaks out.
• Do not use the appliance if parts are missing or defective or if the power cord or plug is damaged.
• Do not use the appliance until you are sure that it is installed in accordance with the instructions provided in this manual and all water, drain, electrical and grounding connections comply with all applicable local regulations and/or other requirements.
• Before carrying out any maintenance or cleaning in the device, unplug the appliance from the mains.
• As a safety measure, we advise you to unplug the appliance and cut the water supply after every use. Maximum water-inlet pressure: 1 MPa. Minimum water-inlet pressure: 0.03 MPa.

• Never unplug the appliance with wet hands.

• To ensure your safety, power plug must be inserted into an earthed three-pole socket. Check carefully and make sure that your socket is properly and reliably earthed.

• It must be possible to disconnect the appliance from the power supply by unplugging it if the plug is accessible, or by means of an all-pole switch upstream of the plug, in accordance with national electrical safety regulations.
• The maximum current of the device is 10 A, make sure that the power supply system (voltage, current and cable) is applicable to the load of the device.
• Make sure that the socket outlet is capable of supporting the Maximum Power rating of the appliance as indicated on the rating plate.
• Water and electrical devices must be connected by a qualified technician in accordance with the manufacturer's instructions and local safety regulations.
• The glass door may reach high temperatures during operation. Keep children and pets away from the glass door. Never open the door during the washing stage.
• Do not operate the device in very wet rooms or in rooms with explosive or caustic gas.
• Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.
• Do not dry unwashed items in the appliance.
• Do not wash items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes, and wax removers.

• Do not wash articles that have been cleaned in, washed in, soaked in, or stained with flammable or explosive substances, like wax, oil, paint, petrol, degreasers, dry-cleaning solvents, kerosene, etc., which may result in fire or explosion.

• Fabric softeners or similar products should be used as specified by manufacturer.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances (such as wax, oil, paint, petrol, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion.
• When washing fabrics that contain vegetable or cooking oil or have been contaminated by hair care products, they should first be washed in hot water with extra detergent. This will reduce, but not eliminate, the hazard.
• The exhaust air must not be discharged into a flue which is for exhausting fumes from appliances burning gas or other fuels.
• The air openings must not be obstructed by a carpet.
• Appliances with a single inlet valve can only be connected to a cold water supply. Appliances with a double inlet valve must be correctly connected to a hot water and cold water supply (depending on the washing machine model).
• The plug must be accessible after installation.
• The appliance must not be installed behind a lockable door, a sliding door, or a door with a hinge on the opposite side to that of the device.
• The appliance shall not be installed in a humid place.
• Do not place other items or appliances (such as microwaves) or objects under pressure on the device.
• The product is exclusive for household use and is only designed for the textiles suitable for machine washing.

• The product cannot be used for commercial or industrial purposes. Do not use the appliance outdoors, even if the area is protected, as it may be exposed to moisture, rain, or thunderstorms.

• Do not insert more laundry load than the allowed load (maximum allowed load indicated in the product data tables).

• The device is not designed to be operated by external switching devices such as timers or remote control systems.
• Do not use an extension lead or multiple sockets.
• Do not wash garments containing glass fibre, such as certain curtains or blinds, as particles may remain in the washing machine and adhere to other types of garments, causing skin irritation.
• Do not stand or sit on the appliance.
• Do not lean against appliance door.
• Flammable and explosive or toxic solvents are forbidden. Do not use detergents containing petrol, alcohol, etc. Use only detergents suitable for machine washing, especially for the drum.
• Garments containing oil may catch fire spontaneously, especially when exposed to heat sources such as a washing machine. The garments are heated, causing an oxidation reaction in the oil. Oxidation generates heat. If heat cannot escape, garments may become hot enough to catch fire. Piling, stacking, or storing garments containing oil retains heat and therefore creates a fire hazard.
• Garments containing vegetable cooking oil or hair care products should first be washed in hot water with extra detergent, this will reduce the hazard, but will not completely eliminate it.
• Make sure that no objects such as lighters, matches, etc. are introduced.
• Close the door properly, if it is difficult to close, check that clothing does not prevent proper closing.

• Make sure that there is no water in the drum before opening the door.

• Once the washing cycle has finished, we recommend removing the laundry as soon as possible to prevent creases.

• This appliance can be used by children aged 8 and above and people with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, as long as they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Do not allow children to play with the device. The cleaning and maintenance of the appliance should not be carried out by children without supervision.
• Children of less than 3 years should be supervised to ensure that they do not play with appliance.
• Children should be supervised to make sure that they do not play with the device.
• Cleaning and maintenance should not be carried out by children without supervision.
• Be sure to use the child lock functions and to switch off the appliance when not in use.
• Keep the cleaning products out of the reach of children.

Cautions during the handling of the machine

• If you wish to change the location of the washing machine, make sure you install the transport bolts again in the device, as they will ensure the interior of the product is not damaged during transport.
• Water accumulated inside the appliance must be drained out.
• Handle the machine carefully. Never hold each protruded part on the machine while lifting. Do not use the door of the device as a handle during transport.
• The device is heavy. Transport it with care.

• Secure the drain and water-supply hose correctly.

• Do not insert hands into the running water extracting tub.

• Do not close the door with excessive force. If it is found difficult to close the door, please check if the clothes are put in or distributed well.
• It is forbidden to wash carpets.
• Never refill the water by hand during washing.

Installation

• The appliance must be handled and installed by 2 or more people to avoid risk of injury. Wear protective gloves when unpacking and installing the product to avoid cutting hazards.
• Keep children away during installation process.
• During installation, make sure that the power cable is not damaged to avoid possible risk of fire or electric shock.
• Before using the device, it is imperative to remove the transport screws.
• Keep the room dry and ventilated.
• Never place the appliance over the opening of an uncovered drain.
• Do not expose the device to temperatures below 5^ C or above 35^ C .
• Do not install in bathrooms or very damp rooms.
• Check that it is correctly levelled on the floor by means of the feet.
• WARNING! Cecotec accepts no liability for incidents caused by improper use outside the rules set out in this instruction manual.

INSTRUCTIONS DE SECURITE

1. Detergent/fabric softener drawer
2. Door
   3.Drum
3. Adjustable feet
4. Main body
5. Power cable
6. Control panel
7. Water inlet valve

Accessories

Fig. 2.

1. Instruction manual
2. Cold water supply hose
3. Fixed spanner
4. Transport hole plug

NOTE:

The graphics in this manual are schematic representations and may not exactly match the device.

2. BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the appliance out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the appliance when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If there is any piece missing or in bad conditions, contact the official Cecotec Technical Support Service immediately.

Box content

• Instruction manual
• Water supply hose
• Fixed spanner
• Plugs

ENGLISH

• Unpack the appliance and keep the original packaging and materials in a safe place. It will help prevent any damage if the appliance needs to be transported in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• To remove the lower part of the packaging, do not tilt the appliance on its front side. Carefully tilt to the side. Never place the appliance directly on the floor on its back or front part.
• Make sure all parts and accessories are present and in good conditions. If there is any piece missing or not in good condition, immediately contact the official Cecotec Technical Support Service.
• Keep all packaging materials away from children.
• Before using the washing machine, the appliance shall be calibrated.
• Before the first wash, you must perform a complete washing cycle without laundry (i.e. with an empty drum).
• Make sure that all pockets are empty. Sharp and rigid items such as coins, brooches, nails, screws, or stones may cause serious damage to this appliance.

3.PRODUCT INSTALLATION

• Make sure that the temperature of the places where the appliance is installed or placed is higher than 0^ C .
• Install the washing machine correctly according to this instruction manual. Keep the washing machine base well-ventilated when it is placed on a carpeted floor. Keep the place neat and tidy as damage caused by insects is not covered by the appliance warranty.

Transport bolts

The appliance is equipped with transport bolts at the back to prevent internal damage during transport.

Removing the transport bolts (Fig. 3)

1. 4 bolts are installed to prevent internal damage during transport. Remove the bolts before using the appliance.
2. If the bolts are not removed, violent vibrations, noise and problems will occur and may even lead to serious damage.
3. Use the spanner provided to loosen the 4 bolts.
4. Slightly twist the rubber on the bolt and then pull out the bolts. Store the bolts and the spanner.
5. The bolts must be refitted when the appliance is transported again.
6. Use the provided plugs to seal the screw holes.

Correct installation (Fig. 4)

Horizontal adjustment:

The angle of inclination must be less than 1 degree.

Fig. 4 key:

1.- Drain hose
2.- 2 cm distance (approx)

Power socket

• The distance between any side of the washing machine and the power socket must be 1.5 mimetres.
• Do not use too many electrical appliances in one socket.

Clean environment

• The wall, door and floor need to be cleaned.
• Install the washing machine on a hard, stable floor with a floor drain instead of a soft carpet or wooden floor.
• Do not place laundry or other items on top of the appliance, otherwise it may affect the normal operation.

Electric connection

1. Do not use a multiple adapter or similar.
2. After using the washing machine, switch off and close the tap.
3. Connect the washing machine to an earthed socket so that it corresponds to the wiring principles.

4. Place the washing machine where the drain hose connection is easy.

5. Contact the technical support service and ask professionals to install the washing machine. Non-specialists can cause damage and problems in the washing machine.

6. Do not place the washing machine in a place where the temperature is below zero. Pipes will freeze and burst. In addition, temperature below zero will damage the knob and buttons.
7. If you transport the appliance in an environment where the temperature is below freezing, then keep the appliance at room temperature for a few hours before starting it.

Earthing

• The washing machine must be connected to an earthed socket. Should a problem occur, the appliance can reduce the risk of electric shock. This appliance is equipped with a cable that includes a wire and a grounded plug. The earthed plug must be plugged into a suitable socket outlet. If you want to know if the appliance is properly grounded, contact your professional service personnel. If the plug does not match the socket, do not change it yourself.

ENGLISH

• Once the washing machine emits smoke or an odour, turn off the power and contact technical support service.
• The appliance must be connected to a water inlet. Use new hoses instead of old ones.
• To ensure quality, water injection tests are carried out before the washing machine leaves the factory, so it is normal that water may be present inside the drum, door seals and door panel.

Water inlet connection

1. The water supply pressure must be between 30kPa and 1000kPa .
2. Do not scrape the screw thread when connecting the inlet hoses to the valves.

3. If the water supply exceeds 1000kpa, install a pressure regulator.

4. Two seals are provided on the connectors at both ends of the hose to prevent water leakage (Figure 5).

5. Open the tap and check the connectors for leaks.
6. Check the hoses regularly. Make sure that the hoses are not kinked or intertwined.

Connection of inlet hose and taps

Figure 6

Check the rubber seals on both sides of the hose, insert a rubber seal into the threaded fittings of each hose.

Fig. 6 key:

1. Rubber seal
2. Water hose

Figure 7

Connect the water supply hoses to the water taps firmly by hand and then tighten another 2/3 turn with pliers. Connect the blue hose to the water tap.

Figure 8

After connecting the inlet hose to the water taps, open the water taps to remove foreign substances (dirt, sand, or sawdust) from the hoses. Let the water drain into a bucket and check the water temperature.

Figure 9

Connect the hoses to the water inlet firmly by hand and then tighten another 2/3 turn with pliers.

Do not over-tighten the hoses as this could damage the valves and cause leaks. Check for leaks by opening the taps. If water leaks, recheck steps 1 to 4.

Fig. 9 key:

1. Water inlet

2. The washing machine is designed for domestic use, do not install it on a ship or caravan.

3. Please, close the tap if it is not going to be used for a long time
4. (e.g. holidays).
5. Remove the plug and cancel the door lock function to prevent children from locking themselves inside.
6. Packaging materials (e.g. plastic, foam) can damage the child's safety and cause suffocation.

Warning: PLACE ALL PACKAGING MATERIALS OUT OF THE REACH OF CHILDREN.

Installing the drain hose

• Secure the drain hose with a rope, wire, cable tie or similar item.
• To avoid damage caused by leakage to the floor, position the drain hose correctly.
• The height of the drain hose should be between (0.85m - 1.25m) above, the terminal should not be placed directly in the water.
• If the drain hose is too long, do not force it to insert it into the appliance, as this will cause abnormal noise.

Please, check Fig. 10 below.

Fig. 10 key:

1. Sink
2. Hose bracket (not included)
3. Wire (not included)

Horizontal adjustment

To avoid noise and vibrations by adjusting the washing machine level:

• Preferably place it in the corner of the room.
• If the floor is not level, straighten with the adjustable feet. Do not place pieces of wood or the like, make sure that all four adjustable feet touch the floor firmly and that the appliance is completely levelled.

Adjusting the adjustable feet

Adjust the adjustable feet to ensure that the washing machine is levelled and that it can be placed firmly on the floor. After adjustment, screw on the locknut to secure. To prevent the machine from falling down, do not place it on a platform that is higher than the floor.

Vertical adjustment

By applying downward force on the washing machine, the washing machine should not shake (both diagonals should be checked, if the washing machine shakes, the adjustable feet should

ENGLISH

be readjusted).

Figure 11

Locking and unlocking the door

Door locking

• After starting a washing programme, the door will automatically lock, and the Door lock indicator light will light up on the control panel.

Door unlocking

• When the door is locked, the Door lock indicator light will be on. Press Start/Pause, the appliance will stop operating. Wait about 2 minutes, the door lock will be deactivated automatically.
• Foam will overflow if you open the door in the middle of a washing cycle. Use a towel to clean it.
• If the water temperature is too high, the door will not open during operation.
• If the water level is too high, the door cannot be opened during operation.

4. OPERATION

Using the detergent drawer

Figure 12

1.- Pre wash detergent:

Add detergent moderately and then select the Pre wash function.

2.- Synthetic washing powder:

Dissolve the detergent (e.g. pieces of soap) before dosing.

2.- Liquid detergent/bleach:

• Use detergent that produces less foam.
• Use two thirds of water (approx.) to dilute the concentrated detergent before dosing.

3.- Softener:

• Add fabric softener before washing, so it will be poured into the drum automatically.
• When using a concentrated type of fabric softener, dilute it appropriately with water.

• Do not exceed the "Max." mark.

• Use specific detergent for delicate clothes.

• Do not use too much detergent, as it will produce too much foam and affect the quality of

the wash or cause malfunction.

• Select the detergent according to the type of laundry, colour, water temperature and water hardness level. Use a neutral detergent for washing effect and to protect the environment.

Tips on the use of detergents at different temperatures

• When washing heavily soiled whites, we recommend using cotton programmes of 60^ or higher and a normal (heavy duty) washing powder containing bleaching agents which at medium/high temperatures give excellent results.
• For washing cycles at temperatures between 40^ and 60^ , the type of detergent used must be suitable for the type of fabric and the level of soiling.
• Normal washing powders are suitable for white or non-fading fabrics with heavy soiling, whereas liquid detergents or K-colour protective washing powders are suitable for coloured fabrics with light soiling levels.
• For washing at temperatures below 40^ we recommend the use of liquid detergents or detergents specifically labelled as suitable for low temperature washing.

Control panel functions

Figure 13

Bolero DressCode 620 E

Figure 14

Bolero DressCode 720 E

1. Power button

• Press it to switch on/off the appliance.

• When the washing cycle finishes, press the Power button to switch off the appliance.

2.Start/Pause button

• Press it to start the washing cycle.
• Press it to pause during operation, press it again to resume operation.

3. Pre wash/Delay start button

Press the Pre wash/Delay start button to delay the start of the washing cycle. You can choose between 3 hours, 6 hours, 9 hours, 12 hours, 15 hours, or 18 hours.

• If you want to cancel the function, simply press the button again.
• The delay start time means from the start of the wash to the end of the wash.
• You can use this function after choosing the washing programme and
• before pressing the Start/Pause button.

ENGLISH

4. Pre wash indicator light Pre Wash

• If the laundry is too dirty, you can use this function before the main washing cycle.
• Press the Pre wash/Delay start button for more than 3 seconds to activate/deactivate this function.

5. Temp. button

• Choose the suitable water temperature according to the type of laundry after pressing the Power button and selecting the programme.

6. Child lock indicator light

• Use this function to prevent children from using the appliance.
• The child lock function locks all buttons/functions except for the Power button.
• Press the Temp. button for more than 3 seconds to activate/deactivate the Child lock function.

7. Speed button

You can choose different spin speeds after selecting the programme.

8. Programme knob

Use the knob to select the programme according to the variety and soiling of the laundry.

9. Status indicator lights

• Door Lock: this indicator light shows whether the door is locked or not.
• Child lock: this indicator light shows if the Child lock function is activated or not.

Programmes

Use for regular clothes

1. Prepairing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Open the detergent drawer, add detergent, and close the drawer.
4. Connect the inlet hose and make sure the tap is open.
5. Press the Power button.
6. The programmes can be selected depending on the laundry and the degree of soiling.
7. Press the Start/Pause button to start washing.

8. When the washing cycle is finished, the appliance will beep.

9. Open the door to remove the clothes.

10. Switch the appliance off and close the tap.

Cotton programme

Use this programme to wash light to moderately soiled laundry such as cotton, bed linen, underwear, towels, and shirts, etc.

1. Preparing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Open the detergent drawer, add detergent, and close the drawer.
4. Connect the inlet hose and make sure the tap is open.
5. Press the Power button.
6. Choose the Cotton programme by turning the programme knob.
7. The washing programme will be selected automatically.
8. Choose the required water temperature and spin speed.
9. Press the Start/Pause button to start washing.
10. When the washing cycle is finished, the appliance will beep.

If you want to change the current setting during the washing cycle, first press the Start/Pause button to stop the cycle, change the settings and then press the button again to restart.

Mixprogramme

Use this programme to wash mixed laundry such as cotton and synthetics (do not mix clothes that fade easily).

1. Preparing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Open the detergent drawer, add detergent, and close the drawer.
4. Connect the inlet hose and make sure the tap is open.
5. Press the Power button.

6. Choose the Mix programme by turning the programme knob.

7. The washing programme will be selected automatically.

8. Choose the required water temperature and spin speed.
9. Press the Start/Pause button to start washing.

10. When the washing cycle is finished, the appliance will beep.

11. If you want to change the current setting during the washing cycle, first press the Start/ Pause button to stop the cycle, change the settings and then press the button again to restart.

12. Separate white or brightly coloured clothes from dark clothes.

Eco 40-60 programme

Use this programme to wash clothes that are not too dirty, therefore saving time and water.

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Eco 40-60 programme by turning the programme knob.

ENGLISH

• The washing programme will be selected automatically.

• Choose the required water temperature and spin speed.

• Press the Start/Pause button to start washing.

• When the washing cycle is finished, the appliance will beep.

If you want to change the current setting during the washing cycle, first press the Start/Pause button to stop the cycle, change the settings and then press the button again to restart.

Underwear programme

Use this programme to wash underwear.

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Underwear programme by turning the programme knob.

7. The washing programme will be selected automatically.

8. Choose the required water temperature and spin speed.
9. Press the Start/Pause button to start washing.
10. When the washing cycle is finished, the appliance will beep.

If you want to change the current setting during the washing cycle, first press the Start/Pause button to stop the cycle, change the settings and then press the button again to restart.

Baby Care programme

Use this programme to wash children's laundry.

1. Preparing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Baby Care programme by turning the programme knob.

7. The washing programme will be selected automatically.
8. Choose the required water temperature and spin speed.
9. Press the Start/Pause button to start washing.

10. When the washing cycle is finished, the appliance will beep.

11. If you want to change the current setting during the washing

12. cycle, first press the Start/Pause button to stop the cycle, change the settings and then press the button again to restart.
13. When removing the laundry, pay attention to the internal steam. To avoid burns, first open the door, wait a few minutes, and then remove the clothes.

Delicate programme

Use this programme to wash delicate clothes, such as silk underwear.

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Delicate programme by turning the programme knob.

7. The washing programme will be selected automatically.
8. Choose the required water temperature and spin speed.
9. Press the Start/Pause button to start washing.
10. When the washing cycle is finished, the appliance will beep.

If you want to change the current setting during the washing cycle, first press the Start/Pause button to stop the cycle, change the settings and then press the button again to restart.

Bedding programme

Use this programme to wash clothes that are labelled as such, e.g. bed linen, sheets, curtains, etc.

1. Preparing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Bedding programme by turning the programme knob.

7. The washing programme will be selected automatically.

8. Choose the required water temperature, spin speed and rinse times.
9. Press the Start/Pause button to start washing.

10. When the washing cycle is finished, the appliance will beep.

11. If you want to change the current setting during the washing cycle, first press the Start/ Pause button to stop the cycle, change the settings and then press the button again to restart.

12. Electric blankets and carpets cannot be washed (it will damage the appliance and clothes).
13. Place the laundry in the drum properly and evenly to optimise spinning, avoid vibrations and prevent long drying times.
14. Heavy laundry can get tangled, so it is necessary to shake it out before drying.
15. Clothes of different materials/fabrics may cause the washing machine not to spin. If that happens, take out the laundry, shake it and put it back into the washing machine.

ENGLISH

Rinse & Spin programme

Use this programme so that the appliance does not perform a washing cycle, but only rinses and spins.

1. Preparing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Press the Power button.

4. Choose the Rinse & Spin programme by turning the programme knob.

5. The washing programme will be selected automatically.

6. Press the Start/Pause button to start washing.

7. When the washing cycle is finished, the appliance will beep.

8. If you want to change the current setting during the washing cycle, first press the Start/ Pause button to stop the cycle, change the settings and then press the button again to restart.

9. The highest spin speed can be selected, but the temperature cannot be adjusted.

Spinprogramme

Use this programme to only spin, the appliance will not wash or rinse.

1. Preparing for the washing cycle
2. Open the door, put the laundry in and close the door.
3. Press the Power button.

4. Choose the Spin programme by turning the programme knob. Press the speed button to set the speed.

5. Press the Start/Pause button.

6. The appliance will start draining the water and then spin.

7. When the washing cycle is finished, the appliance will beep.

8. If you want to change the current setting during the washing cycle, first press the Start/Pause button to stop the cycle, press the speed button to change the speed and then press the Start/Pause button again to restart.

9. During the spin process, the actual spin speed may not match the programme speed, which is due to the fact that the appliance adjusts the speed according to the weight of the laundry.
10. There may be a rhythmic buzzing noise during the spin process, which is the normal noise of the drain. This is not a fault of the washing machine.

Drum Clean programme

1. Prepairing for the washing cycle.

2. Make sure the drum is empty before cleaning it.

3. Open the detergent drawer and add liquid bleach to the main wash compartment.

4. Do not add detergent or laundry detergent to prevent excessive foaming.

5. Close the detergent drawer.

6. Make sure that the inlet hose is properly connected and that the tap is open.

7. Press the Power button.

8. Choose the Drum clean programme by turning the programme knob

9. Press the Start/Pause button.

10. The washing cycle starts after the door has been locked.

11. The appliance beeps when the washing cycle has finished.

12. After finishing the programme, dry the inside of the appliance to prevent the door from warping.

13. If there are children in the house, do not open the door for too long.

Wool programme

Use this programme to wash wool fibre texture, such as machine washable woollen fabrics, etc.

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Wool programme by turning the programme knob.

7. The washing programme will be selected automatically.

8. Choose the required water temperature and spin speed.

9. If you want to change the current setting during the washing cycle, first press the Start/Pause button to stop the cycle, press the speed button to change the speed and then press the Start/Pause button again to restart.

10. When the washing cycle is finished, the appliance will beep.

11. If you want to change the current setting during the washing cycle, first press the Start/ Pause button to stop the cycle, change the settings and then press the button again to restart.

12. After the washing is finished, do not leave the laundry in the washing machine for a long time. Dry it as quickly as possible.
13. Separate white or brightly coloured clothes from dark clothes for washing.
14. The use of special detergent for wool can reduce the damage of the laundry and improve the washing effect.

Jackets programme

1. Prepairing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Open the detergent drawer, add detergent, and close the drawer.

ENGLISH

• Connect the inlet hose and make sure the tap is open.
• Press the Power button.

• Choose the Jackets programme by turning the programme knob.

• The washing programme will be selected automatically.

• Choose the required water temperature and spin speed.
• Press the Start/Pause button to start washing.
• When the washing cycle is finished, the appliance will beep.

If you want to change the current setting during the washing cycle, first press the Start/Pause button to stop the cycle, change the settings and then press the button again to restart.

Sportwear programme

Use this programme to wash machine washable sportswear.

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Sportwear programme by turning the programme knob.

7. The washing programme will be selected automatically.

8. Choose the required water temperature and spin speed.
9. Press the Start/Pause button to start washing.
10. When the washing cycle is finished, the appliance will beep.

Quick 42'programme

Use this programme to wash clothes that are frequently changed and not too dirty.

1. Preparing for the washing cycle.
2. Open the door, put the laundry in and close the door.
3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Quick 4Z' programme by turning the programme knob.

7. The washing programme will be selected automatically.
8. Choose the required water temperature and spin speed.
9. Press the Start/Pause button to start washing.

10. When the washing cycle is finished, the appliance will beep.

11. If you want to change the current setting during the washing cycle, first press the Start/ Pause button to stop the cycle, change the settings and then press the button again to restart.

12. To guarantee the washing effect, it is recommended not to wash more than 4kg of laundry.

Quick 15' programme

Use this programme to wash clothes that are frequently changed and not too dirty.

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Quick 15' programme by turning the programme knob.

7. The washing programme will be selected automatically.

8. Choose the required water temperature and spin speed.

9. Press the Start/Pause button to start washing.

10. When the washing cycle is finished, the appliance will beep.

11. If you want to change the current setting during the washing cycle, first press the Start/ Pause button to stop the cycle, change the settings and then press the button again to restart.

12. To guarantee the washing effect, it is recommended not to wash more than 2kg of laundry.

Synthetics programme (only available for model 620 E)

Use this programme to wash mixed laundry such as cotton and synthetics (do not mix clothes that fade easily).

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the Synthetics programme by turning the programme knob.

7. The washing programme will be selected automatically.

8. Choose the required water temperature and spin speed.

9. Press the Start/Pause button to start washing.

10. When the washing cycle is finished, the appliance will beep.

20 °C programme (only available for model 720 E)

Use this programme to wash lightly stained and lightly used laundry.

1. Preparing for the washing cycle.

2. Open the door, put the laundry in and close the door.

3. Open the detergent drawer, add detergent, and close the drawer.

4. Connect the inlet hose and make sure the tap is open.

5. Press the Power button.

6. Choose the 20^ programme by turning the programme knob.
7. The washing programme will be selected automatically.

ENGLISH

• Choose the spin speed.
• Press the Start/Pause button to start washing.
• When the washing cycle is finished, the appliance will beep.

NOTE: programmes may vary depending on the washing machine model.

NOTE: some functions, such as spin speed, are not configurable in certain programmes.

Washing programmes

Bolero DressCode 620 E

Programme Temperature (℃) Spin speed (r/min) Time (min)
Cotton Cold (20℃, 40℃, 60℃, 90℃)		800 (0, 400, 1000) 54
Mix Cold (20℃, 40℃)	800 (0, 400) 60
Eco 40-60 40℃ (cold, 20℃, 60℃) 1000 (0, 400, 800) 198
Underwear 20℃ (cold, 40℃) 800 (0, 400) 59
Baby care 60℃ (40℃, 90℃) 800 (0, 400, 1000) 126
Delicate	20℃ (cold, 40℃)	800 (0, 400)	48
Bedding	40℃ (cold, 20℃) 800 (0, 400) 68
Synthetics	40℃ (cold, 20℃, 60℃)	800 (0, 400, 1000)	67
Quick 15'	Cold (20℃, 40℃) 800 (0, 400) 15
Quick 42'	20℃ (cold, 40℃)	800 (0, 400)	42
Sportwear	Cold (20℃, 40℃)	800 (0, 400)	44
Jackets	40℃ (cold, 20℃) 800 (0, 400) 58
Wool	40℃ (cold, 20℃) 800 (0, 400) 47
Drum cleaning	60℃	800	75
Spin	—	800 (0, 400, 1000) 10

Rinse & Spin — 800 (0, 400, 1000) 16

Instructions

1. Time may vary due to water pressure, drainage condition, fabric of clothing, weight, change of water temperature, etc.
2. During the washing cycle, the washing and spinning time will be different from the actual run time.
3. During the washing cycle, the actual display time may change according to the detection of the change in weight of the laundry.
4. Due to the different weight of laundry and detergent, if the spin speed is too low, the rinsing performance will not be good, therefore increase the rinsing times.
5. The data in the chart may be different for different models. If you edit the preset programme as energy efficient programme, the washing time will automatically increase.

Washing programmes

Bolero DressCode 720 E

Programme Temperature (℃)	Time (min)
Cotton Cold (20℃, 40℃)	800 (0, 400, 1000) 54
Mix	Cold (20℃, 40℃)	800 (0, 400)
Eco 40-60	40 ℃ (cold, 20 ℃, 60 ℃)	1200 (0, 400, 800)
Underwear	20 ℃ (cold, 40 ℃)	800 (0, 400)
Baby care	60 ℃ (40 ℃, 90 ℃)	800 (0, 400, 1200)
Delicate	20 ℃ (cold, 40 ℃)	800 (0, 400)
Bedding	40 ℃ (cold, 20 ℃)	800 (0, 400)
20℃	20℃	1200(0, 400, 800)
Quick 15'	Cold (20 ℃, 40 ℃)	800 (0, 400)
Quick 42'	20 ℃ (cold, 40 ℃)	800 (0, 400)
Sportwear	Cold (20 ℃, 40 ℃)	800 (0, 400)

ENGLISH

Jackets 40 °C (cold, 20 °C) 800 (0, 400) 58
Wool 40 °C (cold, 20 °C) 800 (0, 400) 47
Drum cleaning 60 °C 800 75
Spin - 800 (0, 400, 1200) 10
Rinse & Spin - 800 (0, 400, 1200) 16

Instructions

1. Time may vary due to water pressure, drainage condition, fabric of clothing, weight, change of water temperature, etc.
2. During the washing cycle, the washing and spinning time will be different from the actual run time.
3. During the washing cycle, the actual display time may change according to the detection of the change in weight of the laundry.
4. Due to the different weight of laundry and detergent, if the spin speed is too low, the rinsing performance will not be good, therefore increase the rinsing times.
5. The data in the chart may be different for different models. If you edit the preset programme as energy efficient programme, the washing time will automatically increase.

Additional functions

Function	Description
Child lock	Indicator light	To prevent children from using the appliance
	Settings for locking/unlocking	During operation, press Temp, for more than 3 seconds to lock, unplug or press Temp, to unlock.
Smart lock	Indicator light	When the operation is finished, if the amount of water inside is high, the water drain pump will be activated to drain below the water level of the door.
Memory mode	Indicator light	When connected to the power supply after shutdown, the operating time will continue from the previous stop point.
Auto door lock Indicator light After selecting the washing programme, the door is automatically locked. Approximately 2 minutes after finishing, it will be unlocked.
Cleaning the drum	Indicator light	To kill bacteria and germs, sterilise to clean the drum.
Delay start Indicator light Press the Pre wash/Delay start button to select the washing machine delay start for 3 h, 6 h, 9 h, 12 h, 15 h, 18 h.

Sterilisation function

This function sterilises the laundry, set the temperature to 90^

NOTE: depending on the model of the washing machine, the "Sterilisation" function may not be available in all washing programmes.

Before washing

1. Washing labels

Please check the washing labels on the clothes, which show the type of fabric and washing method.

(Available on garment labelling).

2. Washing classification

Please wash clothes of the same texture, as different textures need different water temperature, speed and washing programme, separate brightly coloured clothes from white ones. Separate dyed cotton clothes from whites, otherwise the latter will be dyed. If possible, do not wash heavily soiled clothes together with less soiled ones.

Degree of soiling (high, medium, light)

Sort and wash clothes according to soiling degree

Colour (white, light colours, dark colours)

Sort and wash

Velvet (easy deterioration)

Sort into white and dark colours

Notes

• When putting small and large clothes together, put the large clothes first, they should be less than half of the total number of clothes. Do not wash a single cloth as this may cause imbalance problems.

ENGLISH

• Add one or two similar items.
• It is advisable to use 3/4 of the drum for each wash.
• Small items of clothing, such as silk stockings and handkerchiefs, should be stored in mesh laundry bags. Before washing a bra with steel rings, remove the rings. If this is not convenient, place them in mesh bags to prevent the bra from slipping into the space between the inner and outer drums.
• Check all pockets and make sure there is nothing inside them. Nails, hairpins, matches, pens, coins, and keys will damage the washer and clothes.
• Zip all clothing, fasten the button and hook, and tie the belt loosely, to ensure that they do not damage other garments.
• First use water with a little detergent to wash the parts with too many stains, such as collar and cuffs.
• Check the door seal and make sure that there is nothing in it.
• Make sure that there is nothing in the drum before washing.
  Use low-foaming detergent.

5. CLEANING AND MAINTENANCE

Maintenance

• Proper maintenance prolongs the lifespan of the appliance.
• Before maintenance, unplug the appliance.

Appliance body

After washing, wipe with a soft cloth. If there is a lot of dirt, use a suitable neutral detergent or soap.

• Do not wet directly.
• Do not use putty powder, thinner, petrol or alcohol to clean the body of the machine.

Door gasket

After washing, remove dirt, paper waste, etc., if there is any foreign matter, remove it.

Cleaning the detergent drawer

Clean the detergent drawer regularly. Take it out and wash it with clean water, then replace it.

Fig. 15 key:

1. Push down
2. Remove

Cleaning the water inlet of the water hose

(Suggestion: once every six months)

If debris accumulates, it will influence the water inlet speed.

1. Disconnect the water inlet hose.
2. Remove the coupling device according to the shown arrow.
3. Clean the inside of the coupling device.
4. Reinstall the hose after cleaning.

Figure 16

Cleaning of the water inlet valve (Suggestion: once every six months)

1. Disconnect the hose from the washing machine.
2. Remove the filter net from the water valve.
3. Clean the filter mesh with a soft bristle toothbrush.
4. Reinstall the hose after cleaning.

Fig.17 key:

1. Water inlet valve

In case of freezing

1. Cover the tap and the coupling device with a hot towel.
2. Remove the inlet hose and place it in 50 degree water.
3. Pour approximately 2 - 3 l of water at 50 degrees into the drum.
4. Connect the inlet hose, open the tap and switch on the washing machine, check if the inlet and outlet are normal.

Fig. 18 key:

a.-

1. tap
2. coupling device
   b.- Remove the inlet hose and place it in water at 50^ .
3. Water at 50^
   c.- Pour approximately 2 - 3 l of water at 50^ into the drum.
4. Water at 50^

Cleaning of the drain pump filter (Suggestion: once a month)

1. Press the lock on the pump after draining (with the washing machine switched off), open the water pump filter cover. Attention: if there is hot water inside, wait for it to cool down.
2. Remove the filter counterclockwise.
3. Wash the filter.
4. Go to the pump and insert the filter, tighten it clockwise and tighten the cap.

Warning:

a. Secure the filter tightly to prevent leakage.
b. Do not clean during operation.

ENGLISH

Drum cleaning (Suggestion: one a month)

After use over a period of time, some dirt may remain. You can clean the inside and outside of the drum using the Drum Cleaning programme. Caution: do not put laundry or use detergent when cleaning the drum.

6. TROUBLESHOOTING

Non-faulty conditions

The door cannot be opened

-Programme is running.
- There is clothing between the door and the door seal.

A slight odour is produced

There may be a rubber odour from some components, the odour will disappear with use. It is recommended to leave the door ajar after each wash until the inside of the drum is completely dry, this will prevent odours and the formation of mould.

There is too little water when washing and rinsing

The washing machine only needs a little water during operation.

No water inlet

• Is the water supply tap open?
• Is the inlet hose frozen?
• Are the filters blocked?
• Is there sufficient water pressure?

Water inlet at half

If the water level is low, the appliance will automatically supply water.

Water comes out when washing

Check if you added detergent with too much foam or too much quantity.

Remaining time change

If the laundry is not evenly placed inside the drum when spinning, the spin time will be increased, in order to even out the imbalance and correct the deviation.

There is an abnormal noise when spinning

Have the transport bolts been removed?

Are there pieces of metal or coins in the drum?

Washing machine cannot work after a power failure

The washing machine will stop working after a power failure. When power is restored, for safety reasons, it will not start up. Press the power button and restart the programme.

ENGLISH

Troubleshooting Guide

Fault	Indicator light
	Child lock 3H 6H	9H
Water inlet	Flashing	Fixed light	Off	Off
Water outlet	Flashing	Off	Fixed light	Off
Problem with the door	Flashing	Off	Off	Fixed light
Spinning problem	Flashing	Fixed light	Off	Fixed light
Water constant	Flashing	Fixed light	Fixed light	Off
When the drum does not spin	Flashing	Fixed light	Fixed light	Off
Too much foam

	Is the water supply cut off or is the water pressure too low?Are the water inlet hoses frozen?Are the filters blocked?	Open the tap.Please wait.Use hot water to defrost the hoses.Remove the filters and clean them.
	Is the drain hose set too high?Is the hose or drain pipe frozen?Are the drain hose and outlet hoses blocked?Is the drain blocked?	Make sure that the height is 1 m.Use hot water to defrost the hoses.Remove foreign matter and dredge the hoses.Clean the drain.
	Make sure that you do not switch on the washing machine without closing the door properly.	Make sure that the door is actually closed.
Check whether the transport bolt has been removed.Is the machine stably positioned?Is the clothing too small or too light?Are the locknuts under the feet tightened?	Remove the transport bolt. Place the appliance on stable and level ground.Add more clothes.Make sure that the feet are securely fastened
	Close the tap, unplug, and contact the official Cecotec Technical Support Service.
	Close the tap, unplug, and contact the official Cecotec Technical Support Service.
	Check if you have added too much detergent.	Add a reasonable amount of detergent.Use detergent correctly.

ENGLISH

7. TECHNICAL SPECIFICATIONS

Reference 01296 01297

Model Bolero DressCode 620 E Bolero DressCode 720 E

QR code

Voltage 220-240V ~

Rated frequency 50Hz

Washing capacity 6kg 7 kg

Rated power rating 400 W 500 W

Rated heating capacity 1500 W 1500 W

Rated washing power 250 W 300 W

Maximum power 1750 W 1750 W

Technical specifications may change without prior notification to improve product quality. Made in China | Designed in Spain

Frequently used programmes

Bolero DressCode 620 E

The following data is for reference only and may vary depending on many factors.

Programme	Tempera-ture (℃)	Time (min)	Water consump- tion (L/ cycle)	Energy consump- tion (kWh/ cycle)	Revo- lutions (rpm)	Maxi- mum load	Average residual moisture
Delicate Cold	0:45 32 0.05	800 ≤Z	kg 95 %
Cotton 20 ℃	20 0:57 58	0,25 800	Rated 76 %
Cotton 90 ℃	80 1:50 60	1.76	800 Rated	76 %
Synthetics 40 ℃	40 1:07 45	0.55 800	≤4 kg 80%
Quick 15'	Cold 0:15 35	0.04	800 ≤2 kg 80%

Bolero DressCode 720 E

The following data is for reference only and may vary depending on many factors.

Programme	Tempera-ture (℃)	Time (min)	Water consump- tion (L/ cycle)	Energy consump- tion (kWh/ cycle)	Revo-lutions (rpm)	Maxi- mum load	Average residual moisture
Wool	Cold	0:41	35	0.06	800	≤2 kg	95 %
Cotton 20 ℃	20	0:57	60	0,25	800	Rated	76 %
Cotton 90 ℃	80	1:50	70	1.8	800	Rated	76 %
20 °C	20	0:57	60	0,25	1200	Rated	76 %
Quick 15'	Cold	0:15	35	0.05	800	≤2 kg	80%

PRODUCT DATA SHEET

Supplier's name or trademark: Cecotec Innovaciones, S.L.

Supplier's address: Av. Reyes Catolicos, 60, 46910, Alfafar, Valencia (Spain)

ENGLISH

Model identifier: Bolero DressCode 620 E General product parameters:

Parameter Value Parameter Value
Rated capacity (a) (kg)	6.0		Dimensions in cm Height 85	5
				Width 60
				Depth 44
IEEw(a) 90.1 Energy efficiency class ( a) E			a) E
Washing efficiency index (a)	1.031		Rinsing efficiency (g/ kg) (a)	5.0
Energy consumption in kWh per cycle, based on the Eco 40-60 programme. The actual energy consumption will depend on how the appliance is used.	0.730		Water consumption in litre per cycle, based on the Eco 40-60 programme. The actual water consumption will depend on how the appliance is used and on the hardness of the water.	43
Maximum temperature inside the treated fabric (a) (oC)	Rated capacity 45		Amount of residual moisture (a) (%)	62.0
	Half 40
	Quarter 40
Spin speed (a) (rpm) Rated capacity 1000			Spin-drying efficiency class (a)	CHalf 1000
						Quarter 1000
Programme duration (h:min)	Rated capacity 3:18		Type	Free installation
	Half 2:36
	Quarter 2:36
Airborne acoustical noise emissions in the spin phase (a) (dB(A) re 1 pW)	74		Airborne acoustic noise emission class (a) (spin phase)	B
Off mode (W)	0.50		Standby mode (W)	N/A

Delay start (W) (if applicable)	4.00 Standby on mains (W) (if applicable)	N/A
Minimum duration of the guarantee offered by the supplier (b):
This appliance has been designed to release silver ions during the washing cycle.	NO
Further information: Link to the supplier's website, where the information of point 9 of Annex II of the Commission Regulation (EU) 2019/2023 (1) (b) can be found: (a) for the eco 40-60 programme. (b) changes to these elements shall not be considered relevant for the purposes of Article 4, paragraph 4, of Regulation (EU) 2017/1369. (c) if the product database automatically generates the final contents of the cell, the supplier does not have to enter this data.

Information to be included in the technical documentation for household washing machines

SETTING UNIT VALUE
Nominal capacity for Eco programme 40-60, at 0.5 kg intervals (c)	kg 6.0
Power consumption of Eco programme 40-60 at nominal capacity (EW, full)	kWh/cycle 0	910
Power consumption of Eco programme 40-60 at half nominal capacity (EW1/2)	kWh/cycle 0	600
Power consumption of the Eco programme 40-60 at one quarter of the nominal capacity (EW1/4)	kWh/cycle 0	554
Weighted energy consumption of Eco 40-60 programme (EW) kWh/cycle 0.730
Standard energy consumption of the Eco 40-60 programme (SCE)	kWh/cycle 0.8	10
Energy Efficiency Index (IEE) - 90.1
Water consumption of the Eco programme 40-60 at nominal capacity (W, complete)	L/cycle 45.0

ENGLISH

Water consumption of Eco programme 40-60 at half nominal capacity (Ww1/2)	L/cycle 41.0
Water consumption of Eco programme 40-60 at one quarter of nominal capacity (Ww1/4)	L/cycle 40.0
Weighted water consumption (Ww) L/cycle 43
Washing efficiency rating of the Eco 40-60 programme at rated capacity (Iw)	-1.031
Washing efficiency rating of Eco programme 40-60 at half rated capacity (Iw)	-1.031
Washing efficiency rating of the Eco programme 40-60 at one quarter of the rated capacity (Iw)	-1.031
Rinsing effectiveness of the Eco 40-60 programme at nominal capacity (IR)	g/kg 5.0
Rinsing effectiveness of Eco 40-60 programme at half rated capacity (IR)	g/kg 5.0
Rinsing efficiency of the Eco 40-60 programme at one quarter of the rated capacity (IR)	g/kg 5.0
Duration of Eco programme 40-60 at rated capacity (tw) (h:min) 3:18
Programme duration Eco 40-60 at half rated capacity (tw) (h:min) 2:36
Eco programme duration 40-60 at one quarter of nominal capacity (tW)	(h:min) 2:36
Temperature reached for a minimum of 5 minutes within the load during the Eco 40-60 programme at rated capacity (T)	°C 45
Temperature reached for a minimum of 5 minutes within the load during the Eco 40-60 programme at half the rated capacity (T)	°C 40
Temperature reached for a minimum of 5 minutes within the load during the Eco 40-60 programme at one quarter of the rated capacity (T)	°C 40
Spin speed in the spin phase of the Eco programme spin phase 40-60 at rated capacity (S)	rpm 1000
Spin speed in the spin phase of the Eco programme 40-60 at half the nominal capacity (S)	rpm 1000
Spin speed in the spin phase of the Eco programme 40-60 at one-quarter of the rated capacity (S)	rpm 1000
Weighted residual moisture content (D) % 62.0
Airborne acoustic noise emissions during Eco 40-60 programme (spin phase)	dB(A) re 1 pW	74
Power consumption in off mode (Pc) 0.50	W
Power consumption in standby mode (Psm) N/A	W
Does 'standby mode' include the display of information? - NO
Standby power consumption (Psm) in mains standby conditions (if applicable)	W	N/A
Power consumption at 'delay start' (Pds) (if applicable) 4.00	W

PRODUCT DATA SHEET

Supplier's name or trademark: Cecotec Innovaciones, S.L.

Supplier's address: Av. Reyes Catolicos, 60, 46910, Alfafar, Valencia (Spain)

Model identifier: Bolero DressCode 720 E

General product parameters:

Parameter Value Parameter Value
Rated capacity (a) (kg)	7.0	Dimensions in cm	Height	85
			Width	60
			Depth	48
IEE_a	90.6	Energy efficiency class (a)	E
Washing efficiency index (a)	1.031	Rinsing efficiency (g/kg) (a)	5.0
Energy consumption in kWh per cycle, based on the Eco 40-60 programme. The actual energy consumption will depend on how the appliance is used.	0.781	Water consumption in litre per cycle, based on the Eco 40-60 programme. The actual water consumption will depend on how the appliance is used and on the hardness of the water.	45

ENGLISH

Maximum temperature inside the treated fabric (°C)	Rated capacity	39	Amount of residual moisture (a) (%)	53.9
	Half 30
	Quarter 31
Spin speed (a) (rpm)	Rated capacity	1200	Spin-drying efficiency class (′)	B
	Half 1200
	Quarter 1200
Programme duration (a) (h:min)	Rated capacity	3:24	Type Free	installation
	Half 2:42
	Quarter 2:42
Airborne acoustical noise emissions in the spin phase(a) (dB(A) re 1 pW)	76		Airborne acoustic noise emission class (a) (spin phase)	B
Off mode (W) 0.50 Standby mode (W) N/A
Delay start (W) (if applicable)	4.00 Standby on mains (W) (if applicable)			N/A
Minimum duration of the guarantee offered by the supplier (b):
This appliance has been designed to release silver ions during the washing cycle.			NO
Further information:Link to the supplier's website, where the information of point 9 of Annex II of the Commission Regulation (EU) 2019/2023 (1) (b) can be found: (a) for the eco 40-60 programme. (b) changes to these elements shall not be considered relevant for the purposes of Article 4, paragraph 4, of Regulation (EU) 2017/1369. (c) if the product database automatically generates the final contents of the cell, the supplier does not have to enter this data

Information to be included in the technical documentation for household washing machines

SETTING UNIT VALUE
Nominal capacity for Eco programme 40-60, at 0.5 kg intervals (c)	kg	7.0
Power consumption of Eco programme 40-60 at nominal capacity (EW, full)	kWh/cycle	1.000
Power consumption of Eco programme 40-60 at half nominal capacity (EW1/2)	kWh/cycle	0.690
Power consumption of the Eco programme 40-60 at one quarter of the nominal capacity (EW1/4)	kWh/cycle	0.560
Weighted energy consumption of Eco 40-60 programme (EW)	kWh/cycle	0.781
Standard energy consumption of the Eco 40-60 programme (SCEW)	kWh/cycle	0.781
Energy Efficiency Index (IEEw) - 90.6
Water consumption of the Eco programme 40-60 at nominal capacity (WW, complete)	L/cycle 50.0
Water consumption of Eco programme 40-60 at half nominal capacity (WW1/2)	L/cycle 45.0
Water consumption of Eco programme 40-60 at one quarter of nominal capacity (WW1/4)	L/cycle 38.0
Weighted water consumption (WW) L/cycle 45
Washing efficiency rating of the Eco 40-60 programme at rated capacity (Iw)	-1.031
Washing efficiency rating of Eco programme 40-60 at half rated capacity (Iw)	-1.031
Washing efficiency rating of the Eco programme 40-60 at one quarter of the rated capacity (Iw)	-1.031
Rinsing effectiveness of the Eco 40-60 programme at nominal capacity (IR)	g/kg 5.0
Rinsing effectiveness of Eco 40-60 programme at half rated capacity (IR)	g/kg 5.0

ENGLISH

Rinsing efficiency of the Eco 40-60 programme at one quarter of the rated capacity (IR)	g/kg 5.0
Duration of Eco programme 40-60 at rated capacity (tW) (h:min) 3:24	4
Programme duration Eco 40-60 at half rated capacity (tw) (h:min) 2:42	2
Eco programme duration 40-60 at one quarter of nominal capacity (tw)	(h:min) 2:42
Temperature reached for a minimum of 5 minutes within the load during the Eco 40-60 programme at rated capacity (T)	°C 39
Temperature reached for a minimum of 5 minutes within the load during the Eco 40-60 programme at half the rated capacity (T)	°C 30
Temperature reached for a minimum of 5 minutes within the load during the Eco 40-60 programme at one quarter of the rated capacity (T)	°C 31
Spin speed in the spin phase of the Eco programme spin phase 40-60 at rated capacity (S)	rpm 1200
Spin speed in the spin phase of the Eco programme 40-60 at half the nominal capacity (S)	rpm 1200
Spin speed in the spin phase of the Eco programme 40-60 at one-quarter of the rated capacity (S)	rpm 1200
Weighted residual moisture content (D) % 53.9
Airborne acoustic noise emissions during Eco 40-60 programme (spin phase)	dB(A) re 1 pW	76
Power consumption in off mode (P0)	W	0.50
Power consumption in standby mode (Psm)	W	N/A
Does 'standby mode' include the display of information? -	NO
Standby power consumption (Psm) in mains standby conditions (if applicable)	W	N/A
Power consumption at 'delay start' (Pds) (if applicable)	W	4.00

8. DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/accumulators and take them to a collection point designated by the local authorities.

Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

Compliance with the above guidelines will help protecting the environment.

9. TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.

It is recommended that repairs be carried out by qualified personnel.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cecotec Technical Support Service at [phone].

10. COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

FRANÇAIS

1. PIECES ET COMPOSANTS

Img. 1.

3. INSTALLATION DU PRODUIT

1. Évier
2. Support tuyau (non inclus)
3. Fil (non inclus)

Réglage horizontal

Programa Algodao (Cotton)

Programa Roupa interior (Underwear)

5. LIMPEZA E MANUTENÇA

Manutenção

3. INSTALLATIE VAN HET APPARAAT

Drum Clean programma

Sportkleding programma (Sportwear)

Was de sportkleding die in de wasmachine gewassen kan worden

Snel 42'programma (Quick 42')

2. Sorteren van de was

Resterendeijdverandering