SMPS 7 E1 - Nail care device SILVERCREST - Free user manual and instructions
Find the device manual for free SMPS 7 E1 SILVERCREST in PDF.
User questions about SMPS 7 E1 SILVERCREST
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Nail care device in PDF format for free! Find your manual SMPS 7 E1 - SILVERCREST and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SMPS 7 E1 by SILVERCREST.
USER MANUAL SMPS 7 E1 SILVERCREST
MANIKÜRE-PEDIKÜRE-SET / MANICURE & PEDICURE SET / SET DE MANUCURE/ PÉDICURE SMPS 7 E1
DE AT CH
MANIKÜRE-PEDIKÜRE-SET
Operation and safety notes
FR BE
SET DE MANUCURE/PÉDICURE
E-TEK Electronics Manufactory Co., LTD
91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park,
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
PEOPLE'S REPUBLIC OF CHINA
Warnings and symbols used. Page 29
Introduction 31
Intended use. Page 31
Scope of delivery. Page 32
Description of parts . 32
Technical data . 33
Safety instructions. Page 34
Attachments 42
Before use 43
Changing the attachment. . Page 44
Operation. 44
Cleaning and care . Page 46
Storage 47
Disposal. 47
Ordering accessories.. 48
Warranty 49
Warranty claim procedure.. . Page 50
Service 50
| Warnings and symbols used The following warnings are used in this user manual and on the packaging: | |||
| WARNING! This symbol in combination with the signal word "Warning" marks a medium-risk hazard that if not prevented could result in death or serious injury. | CAUTION! This symbol in combination with the signal word "Caution" marks a low-risk hazard that if not prevented could result in minor or moderate injury. | ||
| NOTE: This symbol in combination with "Note" provides additional useful information. | ~ | Alternating current/voltage | |
| - | Direct current/voltage | ||
| Hz | Hertz (supply frequency) | W | |
| (SMPS) Switched-mode power supply | VI | Efficiency class 6 | |
| Enclosed safety transformer | Do not use the power adaptor if the pins of the plug are damaged. | ||
| Polarity of d.c. power connector | Symbol for a Protection Class II product | ||
| CE | CE mark indicates conformity with relevant EU directives applicable for this product. | Use the product in dry indoor spaces only. | |
| IP20 | Protection against solid objects with a diameter of more than 12.5 mm | t_a | Nominal ambient temperature |
| ○○ | Clockwise / Off / Counter-clockwise | ||
MANICURE & PEDICURE
SET
Introduction
We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.
Intended use
This product is intended solely for the care and maintenance of fingernails, toenails and feet.
This product is only intended for private household use, not for commercial purposes.
The power adaptor is intended for indoor use only.
The manufacturer accepts no liability for damages caused by improper use.
Scope of delivery
After unpacking the product, check if the delivery is complete and if all parts are in good condition. Remove all packaging materials before use.
1 Main unit
1 Power adaptor
1 Sapphire cone
1 Felt cone
1 Coarse sapphire disc
1 Fine sapphire disc
1 Flame file
1 Cylindrical file
1 Sapphire callus remover
1 Storage bag
1 Operating instructions
Description of parts
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the product.
(Fig. A)
1 Attachment fitting
2 button (increase speed)
3 button (reduce speed)
4 Main unit
5 Rotating direction indicator light
(red = clockwise,
green = counter-clockwise)
6 On/off/direction switch
7 DC socket
8 DC plug
9 Power adaptor
10 Storage bag
11 Sapphire callus remover
12 Cylindrical file
13 Flame file
14 Fine sapphire disc
15 Coarse sapphire disc
16 Felt cone
17 Sapphire cone
Technical data
Main unit
Rated voltage: 30V
Rated current: 0.25 A
Ingress protection: IP20
Sound pressure level: 68 dB(A)
Power adaptor
Manufacturer's name or trade mark, commercial registration number and address:
E-TEK Electronics Manufactory Co., LTD 91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park, Yanchuan, Songgang Subdistrict, Bao'an District, 518105 Shenzhen, Guangdong, PEOPLE'S REPUBLIC OF CHINA
Model identifier: ZD12D300025EU
Input voltage: 100 - 240V
Input AC frequency: 50 / 60Hz
Input current: 0.5 A
Output voltage: 30V
Output current: 0.25 A
Output power: 7.5 W
Average active efficiency: 82%
No-load power
consumption: 0.10 W
Protection class:
Ingress protection: IP20
Nominal ambient
temperature (t_a) .. 40^
Safety instructions
BEFORE USING
THE PRODUCT,
PLEASE FAMILIARISE
YOURSELF WITH
ALL OF THE SAFETY
INFORMATION AND
INSTRUCTIONS FOR
USE! WHEN PASSING
THIS PRODUCT ON
TO OTHERS, PLEASE
ALSO INCLUDE ALL
THE DOCUMENTS!
In the case of damage
resulting from non-
compliance with these
operating instructions
the warranty claim
becomes invalid!
No liability is accepted for consequential damage! In the case of material damage or personal injury caused by incorrect handling or non-compliance with the safety instructions, no liability is accepted!
WARNING! RISK OF LOSS OF LIFE OR ACCIDENT TO INFANTS AND CHILDREN!
Never leave children
unsupervised with the
packaging material.
The packaging
material represents
a danger of
suffocation.
Children frequently underestimate the dangers. Always keep children away from the packaging material.
This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved.
beThis product can be used by children aged from 3 years and above if they are continuously supervised.
Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervision.
WARNING! RISK OF INJURY!
Prior to use, check the product for visible external damage. Do not operate the product, if it has been damaged or dropped.
All repairs must be carried out by authorised specialist companies or by the Customer Service department. Improper repairs can pose significant risks to the user. The warranty claim will also be invalidated.
Extended use may cause extreme warming of the skin. Therefore, take frequent breaks. Otherwise, there is a risk of burns!
WARNING! Keep the product dry.
Do not use the product while bathing or showering.
Never touch the product with wet or moist hands.
Always operate the product with the supplied power adaptor.
CAUTION! RISK OF PROPERTY DAMAGE!
Defective components must always be replaced with original replacement parts. Compliance with safety requirements can only be guaranteed if original replacement parts
Do not use the power are used.
adaptor to charge any other device.
Protect the product from penetration by moisture and liquids.
Protect the product against knocks, dampness, dust, chemicals, and extreme temperatures.
Keep the product away from sources of heat (e.g. ovens, radiators).
Never use the product under blankets, pillows, etc.
Do not store the product where it could fall into a bath tub or wash basin.
Never submerse the product in water or other liquids.
No action is needed from users to shift the product between 50 and 60Hz The product adapts itself for both 50 and 60Hz
After use: Always remove the power adaptor from the socket-outlet. Never pull on the connection cord.
The connection cord of the power adaptor cannot be replaced. If the connection cord is damaged, the power adaptor must be disposed of.
Ensure that the drive can always rotate freely. Otherwise, the product may overheat and be damaged beyond repair.
The power adaptor is intended for indoor use only.
To disconnect the power supply to the product, pull the power adaptor from the socket-outlet.
The socket-outlet that is used must be easily accessible so that the power adaptor can be quickly removed from the socket-outlet in the event of an emergency.
In the event of a malfunction (unusual noises or smoke) or during thunderstorms, disconnect the power adaptor from the socket-outlet.
Repairs to the product during the warranty period may only be carried out by a customer service department authorised by
- Never try to open the manufacturer.
- housing of the power
- otherwise no adaptor - there is a additional warranty
- risk of electrocution. claims can be
- To avoid damage considered for
- caused by unwanted subsequent damage.
- warming, do not
- cover the power adaptor.
Attachments
Sapphire callus remover 11:
For large-scale and rapid removal of thick hardened skin or calluses on the sole or heel of your foot
- Guide the sapphire callus remover [11] over the parts of the sole and heel to be treated while exerting gentle pressure.
Cylindrical file 12
For grinding off thick toenail surfaces and rough smoothing of the surfaces
- Always hold the cylinder file [12] parallel to the nail surface and apply light pressure and circular movements to remove the excess growth.
Flame file 13
For freeing ingrown nails
- Guide the flame file 13 carefully onto the treatment area and cut away the affected nail part.
Fine and coarse sapphire disc 14 15:
For filing and working the nails -Work the edge of the nail using the fine and coarse sapphire disc 14 15. Since only the inner disc rotates and the outer edge does not move, you can file your nails accurately without damaging your skin with the rapidly rotating disc.
- Always work from the outside of the nail to the tip.
Felt cone 16:
For smoothing and polishing
nail edges after filing, and for
cleaning the nail surface
Use the felt cone 16 to polish and smooth the edge of the nail and to clean the nail surface after grinding. Always polish in a circular motion and never let the felt cone stay in one place.
Sapphire cone 17
For removing dry skin, hardened skin or calluses on the soles and heels
- Guide the sapphire cone [17] over the parts of the sole and heel to be treated using a circular motion while exerting gentle pressure. Do not press too firmly, and always guide the sapphire cone carefully to the surface to be treated. Apply a moisturising cream after every treatment.
Before use
Only use the product with dry hands.
Remove all parts from the packaging.
Changing the attachment
Unplug the main unit 4 each time before you change the attachment.
Pull the attachment out of the main unit 4, if any.
Select an attachment (see fig. A and the "Attachments" chapter).
Push the attachment into the main unit 4. Make sure the attachment is installed firmly.
NOTE: Change the attachment when it looks or feels worn.
Operation
WARNING! RISK OF INJURY!
Excessively long or intensive treatment can also injure deeper layers of skin.
Therefore, check the treatment progress and results regularly. Diabetics in particular are less sensitive on their hands and feet.
WARNING! RISK OF BURNS DUE TO SEVERE HEAT DEVELOPMENT!
While you are working, never let the attachments remain in one location. Friction leads to increased heat generation and may cause injuries.
Always work with a circular motion.
Find a well-lit place to work. There must be a socket-outlet in close proximity.
Insert the appropriate attachment for your purpose in the attachment fitting 1. The attachment must sit securely.
Connect the DC plug 8 to the DC socket 7.
Plug the power adaptor into a socket-outlet.
Switch on the product.
Select the rotating direction:
Switch 6
Indicator light 5
Rotating direction
Slide the switch to the left. red clockwise
Slide the switch to the right. green counter-clockwise
Slide the switch to the middle.
off off
NOTE: The indicator light 5 flashes when the highest or lowest setting has been reached.
Always start the treatment at slow speed and only increase it when necessary.
Speed Press button
Increase speed
Press 2 button.
Reduce speed
Press 3 button.
Switch off the product: Slide the switch 6 to 0 position.
Disconnect the power adaptor 9 from the socketoutlet when you have finished the treatment.
NOTE: Set the speed to the lowest setting after you changed the rotating direction or an attachment.
1 NOTES:
If you have treated hardened skin, apply a moisturising cream to the treated areas after completing the procedure.
The attachments do not have as much effect on softened skin. Therefore, do not carry out any pretreatment in a water bath before using the product.
Always select the rotating direction for treating the nails in their direction of growth. If possible, treat the nails from the outside towards the inside (to the nail tip). Otherwise, the nails will split more easily.
If you feel that the nails could crack during treatment, select the other direction.
Cleaning and care
WARNING! Risk of electrical shock! Before cleaning: Always disconnect the power adaptor from the socket-outlet.
Do not use chemical, aggressive or abrasive cleaning agents. These can damage the surface of the product.
Clean the main unit 4 and the power adaptor 9 with a damp cloth. For stubborn soiling use a mild detergent on the cloth. Ensure that no water or moisture can penetrate the product. Dry all parts thoroughly.
For hygienic reasons, we recommend cleaning the attachments with a clean cloth or brush moistened with alcohol after every use. Dry all parts thoroughly.
Storage
After you have cleaned the product, put it back in the storage bag 10.
Store the product in a dry and clean location.
Disposal
The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.
Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1-7: plastics / 20-22: paper and fibreboard / 80-98: composite materials.
The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.
Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.
To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.
Ordering accessories
You can order the following replacement parts for this product:
11 Sapphire callus remover
12 Cylindrical file
13 Flame file
14 Fine sapphire disc
15 Coarse sapphire disc
16 Felt cone
17 Sapphire cone
Order the replacement part via our website:
www.optimex-shop.com
Warranty
The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.
The warranty for this product is 3 years from the date of purchase. The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your proof of purchase.
Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it - at our choice - free of charge to you. This warranty becomes void if the product has been damaged, or used or maintained improperly.
The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts.
Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
Please have the till receipt and the item number (IAN 375863_2107) available as proof of purchase.
You will find the item number on the rating plate, an engraving, on the front page of the instructions for use (bottom left), or as a sticker on the rear or bottom of the product.
If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.
You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.
Service
GB Service Great Britain
Tel.:08000569216
E-Mail: owim@lidl.co.uk
IE Service Ireland
Tel.:1800200736
E-Mail: owim@lidl.ie
SET DE MANUCURE/ PÉDICURE
Introduction
E-TEK Electronics Manufactory Co., LTD
91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park,
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
E-TEK Electronics Manufactory Co., LTD 91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park, Yanchuan, Songgang Subdistrict, Bao'an District, 518105 Shenzhen, Guangdong, VOLKSREPUBLICK CHINA
Typeaanduiding: ZD12D300025EU
Voedingsspanning: 100-240 V~
Voedingsfrequentie: 50 / 60Hz
Voedingsstroom: 0,5 A
E-TEK Electronics Manufactory Co., LTD
producenta, numer rejectru
91440300755667743W
handlowego i adres:
B, 3 Bldg, Tangwupu Industrial Park,
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
CHINY
Identityfikator modelu: ZD12D300025EU
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
CÍNSKÁ LIDOVÁ REPUBLÍKA
Identifikaciniznacka modelu: ZD12D300025EU
ve smeruhodinovych ruicek
Posunte spinač doprava. zelena
profismeruhodinovychrucicek
Posunte spinae do stredu. vyp
UPOZORNÉNÍ:
E-TEK Electronics Manufactory Co., LTD 91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park, Yanchuan, Songgang Subdistrict, Bao'an District, 518105 Shenzhen, Guangdong, CINSKA L'UDOVA REPUBLICA
protsmeruhodinovychruciiek
Spinač posuţe do stredu. vyp. yyp.
E-TEK Electronics Manufactory Co., LTD
B, 3 Bldg, Tangwupu Industrial Park,
del fabricante:
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
REPUBLICA POPULAR CHINA
E-TEK Electronics Manufactory Co., LTD
91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park,
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
KINA
Modellens
identifikationskode: ZD12D300025EU
Indgangsspaending: 100-240 V~
Inputvekselstrømsfrekvens:50/60 Hz
Safirliber for hards hud
12
Cylinderfraeser
13
Flammefraeser
14
Safirskive fin
15
Safirskive grov
16
Filtkegle
17
Safirkegle
E-TEK Electronics Manufactory Co., LTD 91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park, Yanchuan, Songgang Subdistrict, Bao'an District, 518105 Shenzhen, Guangdong, PEOPLE'S REPUBLIC OF CHINA
Identificativo del modello: ZD12D300025EU
D I C E S S I O N E D E L
PRODOTTO A TERZI,
AVERE CURA DI
CONSEGNARE
TUTTA LA
DOCUMENTAZIONE!
www.optimex-shop.com
Garanzia
E-TEK Electronics Manufactory Co., LTD
91440300755667743W
B, 3 Bldg, Tangwupu Industrial Park,
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
KINAI NÉPKÖZTÁRSASAG
Naziv proizvajalca ali E-TEK Electronics Manufactory Co., LTD
blagovna znamka, stevilka 91440300755667743W
vpisa v register gospodarskih B, 3 Bldg, Tangwupu Industrial Park,
druzb in naslov:
Yanchuan, Songgang Subdistrict, Bao'an
District, 518105 Shenzhen, Guangdong,
LJUDSKA REPUBLIKA KITAJSKA
Identifikacijska oznaka
modela: ZD12D300025EU
Vhodna napetost: 100-240 V~
