WX718 - Grinder WORX - Free user manual and instructions

USER MANUAL WX718 WORX

1.SAFETY INSTRUCTIONS ORIGINAL INSTRUCTIONS PRODUCT SAFETY GENERAL POWER TOOL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3.PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/ or the battery pack from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5. SERVICE

a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

SAFETY WARNINGS COMMON FOR GRINDING OR ABRASIVE CUTTING-OFF OPERATIONS:

a) This power tool is intended to function as a grinder, or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
b) Operations such as sanding, wire brushing, polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your

accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.

f) Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
j) Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock
k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
I) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.

n) Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
o) Do not operate the power tool near flammable materials. Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
q) Your hand must hold on the handle when you are working. Always use the auxiliary handles supplied with the tool. Loss of control can cause personal injury

FURTHER SAFETY INSTRUCTIONS FOR ALL OPERATIONS

Kickback and RelatedWarnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel's movement at the point of pinching. Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory. Accessory may kickback over your hand.
c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.

ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDING AND CUTTING-OFF OPERATIONS Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations:

a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.
b) The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
c) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect operator from broken wheel fragments and accidental contact with wheel and sparks that could ignite clothing.
d) Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

ADDITIONAL SAFETY INSTRUCTIONS FOR

CUTTING-OFF OPERATIONS

Additional SafetyWarnings Specific for Abrasive Cutting-Off Operations:

a) Do not "jam" the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
f) Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

SYMBOLS

To reduce the risk of injury, user must read instruction manual

Double insulation

Warning

Wear ear protection

Wear eye protection

Wear dust mask

Wear protective gloves.

Make sure the tool is unplugged prior to changing accessories.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

2.COMPONENT LIST

1. SPINDLE LOCK BUTTON

2. ON/OFF SWITCH

3. AUXILIARY HANDLE

4. SPANNER

5. INNER FLANGE

6. OUTER FLANGE

7. WHEEL GUARD*

8. DISC*

*Not all the accessories illustrated or described are included in standard delivery.

3. TECHNICAL DATA

Type WX718 WX718.X WX717 WX717.X(700-749 -designation of machinery, representative of Angle Grinding)

	WX718 WX718.X**	WX717 WX717.X**
Voltage 220-240V~50/60Hz
Power input 900 W 750 W
Rated speed 1200 0 /min 11000 /min
Disc Size 125 mm 115 mm
Disc bore 22.2 mm
Spindle thread M14
Protection class	☐/II
Machine weight	2.17 kg	1.77 kg

X = 1 - 999 A-Z, M1-M9 there are only used for different customers, there are no safe relevant changes between these models

We recommend that you purchase your accessories from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.

NOISE INFORMATION

	WX718 WX718.X	WX717 WX717.X
A weighted sound pressure	LpA: 83,6 dB(A)	LpA: 83.7 dB(A)
A weighted sound power	LwA: 94,6 dB(A)	LwA: 94.7 dB(A)
K & K pA wA	3.0 dB
Wear ear protection

VIBRATION INFORMATION

		WX718 WX718.X	WX717 WX717.X
Vibration total values (triax vector sum) determined according to EN 60745:
Grinder	surface grinding	Vibration emission value ah,AG = 4,320 m/s2	Vibration emission value ah,AG = 4.106 m/s2
	Uncertainty K = 1.5m/s2

The declared vibration total value may be used for comparing one tool with another, and may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission value

during actual use of the power tool can differ

from the declared value depending on the ways in which the tool is used dependant on the following examples and other variations on how the tool is used:

How the tool is used and the materials being cut.

The tool being in good condition and well maintained The use the correct accessory for the tool and ensuring it is sharp and in good condition.

The tightness of the grip on the handles and if any anti vibration accessories are used.

And the tool is being used as intended by its design and these instructions.

This tool may cause hand-arm vibration syndrome if its use is not adequately managed.

WARNING! To be accurate, an estimation of

exposure level in the actual conditions of use

should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level

over the total working period.

Help to minimize your vibration exposure risk.

Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate)

If the tool is to be used regularly then invest in anti vibration accessories.

Avoid using tools in temperatures of 10^ or less

Plan your work schedule to spread any high vibration tool use across a number of days.

4.INTENDED USE

The machine is intended for cutting, roughing and brushing metal and stone materials without using water. For cutting metal, a special protection guard for cutting (accessory) must be used.

5.OPERATING

INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

ASSEMBLY AND OPERATION

Action Figure
ASSEMBLY
Assembling Auxiliary Handle See Fig. A
Assembling Grinding/Cutting Disc	See Fig. B1,B2,B3

REPLACING DISC

NOTE: Before any work on the machine itself, pull the mains plug. For work with grinding or cutting discs, the protection guard must be mounted.

Removing the disc by following the reverse steps of Fig. B1,B2,B3.
Removing the wheel guard.	See Fig. C1, C2(For WX718 WX718.X)
	See Fig. D1, D2(For WX717 WX717.X)
Repalcing the wheel guard. NOTE: The coded projection on the wheel guard ensures that only a guard that fits the machine type can be mounted. NOTE: Place the wheel guard with coded projection into the coded groove on the spindle of the machine head and rotate to the required position (working position). The closed side of the wheel guard must always point to the operator. NOTE: To fasten the wheel guard by closing the clamping lever (For WX718 WX718.X), or tightening the screw(For WX717 WX717.X).
Repalcing the disc.
OPERATION
Plugging in the Power See Fig. E
Using On/Off Switch See Fig. F
Hand Grip Areas See Fig. G
Rough Grinding WARNING! Never use a cutting disc for roughing.
Cutting See Fig. H

WORKING HINTS FOR YOUR ANGLE GRINDER

1. Always start at no load to achieve maximum speed then start working.
2. Do not force the disc to work faster, reducing the Disc's moving speed means longer working time.
3. Always work with a 15-30 angle between disc and workpiece. Larger angles will cut ridges into the workpiece and affect the surface finish. Move the angle grinder across and back and forth over the workpiece.
4. When using a cutting disc never change the cutting angle otherwise you will stall the disc and angle grinder motor or break the disc. When cutting, only cut in the opposite direction to the disc rotation. If you cut in the same direction as the disc rotation the disc may push itself out of the cut slot.
5. When cutting very hard material best results can be achieved with a diamond disc.

6. When using a diamond disc it will become very hot. If this happens you will see a full ring of sparks around the rotating disc. Stop cutting and allow to cool at no load speed for 2-3 minutes.

7. Always ensure the workpiece is firmly held or clamped to prevent movement.

6.MAINTENANCE

Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.

There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

TROUBLESHOOTING

Although your new angle grinder is really very simple to operate, if you do experience problems, please check the following:

1. If your grinder will not operate check the power at the main plug.
2. If your grinder wheel wobbles or vibrates, check that outer flange is tight; check that the wheel is correctly located on the flange plate.
3. If there is any evidence that the wheel is damaged do not use as the damaged wheel may disintegrate, remove it and replace with a new wheel. Dispose of old wheels sensibly.
4. If working on aluminum or a similar soft alloy, the wheel will soon become clogged and will not grind effectively.

7 ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

8. DECLARATION OF CONFORMITY

We,

Positec Germany GmbH

Postfach 32 02 16, 50796 Cologne, Germany

Declare that the product,

Description Worx Angle Grinder

Type WX718 WX718.XWX717 WX717.X(700-749

-designation of machinery, representative of Angle.
Grinder)

Function Peripheral and lateral grinding

Complies with the following Directives,

2006/42/EC

2011/65/EU&(EU)2015/863

2014/30/EU

Standards conform to:

EN IEC 55014-1 EN IEC 55014-2

EN IEC 61000-3-2 EN 61000-3-3

EN 60745-1 EN 60745-2-3

The person authorized to compile the technical file, Name: Marcel Filz

Address: Positec Germany GmbH

Postfach 32 02 16, 50796 Cologne, Germany

2022/3/31

Allen Ding

Deputy Chief Engineer, Testing & Certification

Positec Technology (China) Co., Ltd

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

INHALTSVERZEICHNIS

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

TABLE DES MATIÈRES

1. CONSIGNES DE SECURITE
2. LISTES DES COMPOSANTS
3. DONNÉES TECHNIQUES
4. UTILISATION CONFORME
5. FONCTIONNEMENT
6. ENTRETIEN
7. PROTECTION DE L'ENVIRONNEMENT
8. DÉCLARATION DE CONFORMITE

1. CONSIGNES DE SECURITE AVERTISSEMENTS DE SECURITE GENÉRAUX POUR L'OUTIL

INFORMATIONS RELATIVES AU BRUIT

INFORMATIONS RELATIVES AUX VIBRATIONS

WX718 WX718.X

WX717 WX717.X

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

WX718 WX718.X

WX717 WX717.X

Codice WX718WX718.XWX717WX717.X (700-

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

TABLA DE CONTENIDOS

WX718 WX718.X

WX717 WX717.X

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

TABLE OF CONTENT

1. INSTRUÇÉS DE SEGURANÇA
2. LISTA DE COMPONENTES
3. DADOS TECNICOS
4. AMBITO DE UTILIZAO
5. FUNCIONAMENTO
6. MANUTENÇA O
7. PROTECÇAO AMBIENTAL
8. DECLARACAO DE CONFORMIDADE

1. INSTRUÇões DE SEGURANÇA AVISOS GÉRAIS DE SEGURANÇA DE FERRAMENTAS ELECTRICAS

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

INHOUDSOPGAVE

1. VEILIGHEIDSINSTRUCTIES
2. ONDERDELENLIJST
3. TECHNISCHE GEGEVENS
4. GEBRUK VOLGENS BESTEMMING
5. BEDIENINGSINSTRUCTIES
6. ONDERHOUD
7. BESCHERMING VAN HET MILIEU
8. CONFORMITEITVERKLARING

1.VEILIGHEIDSINSTRUCTIES ALGEMENE

VEILIGHEIDSWAARSCHUWING- EN VOOR VERMOGENSMACHINE

WAARSCHUWING! Lees alle instructies

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

INDHOLDSFORTEGNELSE

1. SIKKERHEDSINSTRUKTIONER
2. AGGREGATELEMENTER
3. TEKNISK DATA
4. MULIG ANVENDELS
5. BRUGSANVISING
6. VEDLIGEHOLDELS
7. MILJØBESKYTTALSE
8. KONFORMITETSERKLÄERING

1.SIKKERHEDSINSTRUKTIONER GENERELLE ADVARSLER IFORBINDELSMED MASKINVÅRKTØJ

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

INNHOILDSFORTEGNEALSE

1. SIKKERHETSINSTRUKSJONER
2. APPARATELEMENTER
3. TEKNISKE DATA
4. FORMÁLSMESSIG BRUK
5. BRUKSANVISNING
6. VEDLIKEHOLD
7. MILJØVERNTILTAK
8. SAMSVARSERKLAERING

1.SIKKERHETSINSTRUKSJONER GENERELLE SIKKERHETS- ADVARSLER FOR ELEKTROVERKTOY

Type WX718 WX718.XWX717 WX717.X (700-749

-betegner maskin, anger Vinkelslipestol)

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

INNEHÄLLSFORTECKNING

1. SÄKERHETS INSTRUKTIONER
2. LADDARENS KOMPONENTER
3. TEKNISKA DATA
   4.ÄNDAMALSENLG ANVÄNDNING
4. BRUKSANVISING
5. UNDERHÄLL
6. MILJÖSKYDD
7. DEKLARATION OM ÖVERENSSTÄMMELSE

1.SÄKERHETS INSTRUKTIONER GENERELLA SÄKERHETSVARELVERKTYG

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

SPIS TRESCI

1. INSTRUKCJE BEZPIECZENSTWA
2. LISTAKOMPONENTOW
3. DANE TECHNICZNE
4. UZYCIE ZGODNE Z PRZEZNACZENIEM
5. INSTRUKCJE OBSLUGI
6. KONSERWACJA
7. OCHRONA SRODOMWISKA
8. DEKLARACJA ZGODNOSCI

1. INSTRUKCJE BEZPIECZENSTWA OGOLNE OSTRZEZENIA DOTYCZACE BEZPIECZENSTWA PODCZAS PRACY Z ELEKTRONARZEDZIAMI

Positec Technology (China) Co., Ltd 18, Dongwang Road, Suzhou Industrial Park, Jiangsu 215123, P. R. China

ΠΙΝΑΚΑΣ ΠΕΡΙEXΟΜΕΝ

1. O△HΓIEΣAΣΦΑΛΕΙΑΣ
2. ΛΙΣΤΑ ΣΥΣΤΑΤΙΚΟΝ
3. TEXNIKEΣ ΠΑΗΡΟΦΟΥΕΣ
4. NPOBAENOMENXPHSH
5. OΔHΓIEΣ ΣΕΙΤΟΥΡΙΑΣ
   6 ΣYNTHPHSEH
6. IPOSTAIA TOY INEPIBAAANTO
   8.△HAQSH YMMOPΦQSH

1.0ΔHΓIEΣ AΣΦΑΛΕΙΑΣ ΠΡΟΕΙΔΟΝΟΙΗΣΕΙΣ AΣΦΑΛΕΙΑΣ ΓΕΝΙΚΟΥ ΗΑEKΤΡΟΚINHTΟΥ

EPTAAEIOY

IPOEIAOIOIH! Aiaβaote oAεc tic unodεiεic. H μη τήρησι των napakatw

unodxiEwv mnpi va exe oauvenia nAektpoannEla, kivduo npkaia c /kai oOapouc tpaupatioouc.

ΦuáéTe oλeTic npoεiδoŋouηeic kal tic odnyie cyia μελλovτικ ᵩavapopá.

O xaapaktnpiooC p i o epyaiao》nou xpnoiopoiaetai otic napakatw npoeisobointikec unodieic apopa n to opnpto (xepiopoc 2e to xepi) nEKTpko uxAvauna oac (uE nEKTpko kaawdo) n to uxAvauna oac u e pataia (xomega).

1. XΩPOΣ EPΓAΞIΔΣ

a) AiatnpieTo xwpo Nou epyaceoKaahop Ka kala wtiogevo.Ataia oTo xwpo nou epyaceoKai mI wtiogevecpiioxc e pyaoiac mOpei va obnynoov oe atuxnata. b) Mv npzoe To nEeKtpko epyaleio 0e Tepiaalov nou unapxki Kivduvoeckpnnc, OTO OIOU npxov EupekTA Upa,aepia nokvN.Ta nEeKtpka epyaleia mOpei va 8nuioupynov otivnpiuo o onoioc mOpesi va avapEeTn oKovn n tCavaOuiaoeic.
c) Otav xnpoiopoite to nEKTpuKo epyaaleio Kpatate ta naiai Ka aaaa tuyov npoogna paekia ano to xwpo nou epyazoe. nepintwnou aa atoa anoanaov tnV npoox' oac mopsi va xaote tov eAeyxo tou mXavmuatoC.

Ppoeiobonouoic Aopaaiaac, Koivc yia Aetoupyie TpoxioaatoN TpiuKnc Konic:

Enpuicwn: Piv xpoonoioe to epyaiaia aot to bio oyniw

προεκτικα.

SYNAPMOANOHTHEKAI AEITOYPTIA

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

TARTALOMJEGYZÉK

1. BIZTONSAGI UTASITÁSK
2. SZIMBOLUMOK
3. MUSZAKI ADATOK
4. RENDELTETES
   5.. HASZNALATI UTASITASOK
5. KARBANTARTÁS
6. KÖRNYEZETVEDELEM
7. MEGFELELOSEGINYILATKOZAT

1.BIZTONSÁGIGUTASITÁSOKELEKTROMOSKÉZISZERSZÁMOKBIZTONSAGOSHASZNÁLATÁVALKAPCSOLATOSÁLTALANOSFIGYELMEZTETÉSE

WX718 WX718.X

WX717 WX717.X

Tipus WX718 WX718.X WX717 WX717.X (700-749

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

CUPRINS

1. INSTRUCTION DE SIGURANTA
2. LISTÄ DE COMPONENTE
3. DATE TEHNICE
4. UTILIZARE CONFORM DESTINATIONI
5. INSTRUCTION DE UTILIZARE
6. INTRETINERE
7. PROTECPIA MEDIULUI
8. DECLARATIE DE CONFORMITATE

1. INSTRUCTION DE SIGURANTA AVERTISMENTE GENERALE DE SIGURANTA PENTRU UNELTE ELECTRICE

AVERTISMENT: Citi toate averismentele de siguranta s toate instructiunile. Dacn

WX718 WX718.X

WX717 WX717.X

Valori totale vibratji (suma vectoriala triaxiala) determinata conform EN 60745:

Function Peripheral and lateral grinding

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

OBSAH

1. BEZPEČNOSTNÉ INSTRUKCIE
2. ZOZNAM SUCASTI
3. TECHNICKE UDAJE
4. NÁVOD NA POUZITIE
5. URČENE POUŽITIE
6. PRE AKUMULÁTOROVÉ NÁRADIE
7. OCHRANA ZIVOTNEHO PROSTREDA
   8.VYHLASENIE O ZHODE

1.BEZPECNOSTNÉ INŠTRUKCIE OBEÇNA BEZPECNOSTNÍ UPOZORNÉNÍ PRO ELEKTRICKÉ NASTROJE

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

OBSAH

1. BEZPECNOSTNE INSTRUKCIE
2. ZOZNAM SUCASTI
3. TECHNICKE UDAJE
4. URÇENE POUŽITIE
5. NÁVOD NA POUZITIE
6. UDRZBA
7. OCHRANA ZIVOTNEHO PROSTREDA
8. VYHLÁSENIE O ZHODE

1.BEZPECNOSTNÉ INŠTRUKCIE VSEOBECNÉ BEZPECNOSTNÉ VAROVANIA NA POUŽIVANIE ELEKTRICKÉHO NÁRADIA

BEZPECNOSTNÉ POKYNY PRE VSETKY CINNOSTI

BEZPECNOSTNE VYSTRAHY SPOLOCNPRE CINNOSTI BRUSENIA A ROZBRUSOVANIA:

DALSIE BEZPECNOSTNE POKNY PRE VSETKY CINNOSTI

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

KAZALO

1. VARNOSTNA NAVODILA
2. SESTAVNI DELI
3. TEHNICNI PODATKI
4. NAVODILA ZA UPORABO
5. NAMENUPORABE
   6.VZDRZEVANJE
6. VAROVANJE OKOLJA
7. IZJAVA O SKLADNOSTI

1.VARNOSTNA NAVODILA SPLOŠNA VARNOSTNA NAVODILA ZA ELEKTRICNA ORODJA

OPOZORILO! Preberite vsa opozorila in

napothe. Napake zaradi neuostoceanja

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

WORX

you've got the power

www.worx.com

Copyright © 2023, Positec. All Rights Reserved.

AR01666904