A320M-DGS - Motherboard ASROCK - Free user manual and instructions

USER MANUAL A320M-DGS ASROCK

Version 1.0 Published February 2017 Copyright©2017 ASRock INC. All rights reserved. Copyright Notice: No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to infringe. Disclaimer: Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation. With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product. is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate” ASRock Website: http://www.asrock.comAUSTRALIA ONLY Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : [phone] ext.123 (Standard International call charges apply) e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.AB350M-HDV/A320M-HDV/A320M-DGS

3AB350M-HDV/A320M-HDV/A320M-DGS

English A320M-DGS: No. Description No. Description 1 USB 2.0 Ports (USB12) 6 USB 3.0 Ports (USB3_34) 2 LAN RJ-45 Port* 7 USB 3.0 Ports (USB3_12) 3 Line In (Light Blue)** 8 DVI-D Port (DVI_CON1) 4 Front Speaker (Lime)** 9 PS/2 Mouse/Keyboard Port 5 Microphone (Pink)**

• ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications. Activity / Link LED Speed LED Status Description Status Description O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection ACT/LINK LEDSPEED LEDLAN Port

** To congure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.Function of the Audio Ports in 7.1-channel Conguration: Port Function Light Blue (Rear panel) Rear Speaker Out Lime (Rear panel) Front Speaker Out Pink (Rear panel) Central /Subwoofer Speaker Out Lime (Front panel) Side Speaker Out

Chapter 1 Introduction

ank you for purchasing ASRock AB350M-HDV/A320M-HDV/A320M-DGS motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

ASRock AB350M-HDV/A320M-HDV/A320M-DGS Motherboard (Micro ATX Form Factor)

ASRock AB350M-HDV/A320M-HDV/A320M-DGS Quick Installation Guide

ASRock AB350M-HDV/A320M-HDV/A320M-DGS Support CD

1 x I/O Panel ShieldAB350M-HDV/A320M-HDV/A320M-DGS

ank you for purchasing ASRock AB350M-HDV/A320M-HDV/A320M-DGS motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

ASRock AB350M-HDV/A320M-HDV/A320M-DGS Motherboard (Micro ATX Form Factor)

ASRock AB350M-HDV/A320M-HDV/A320M-DGS Quick Installation Guide

ASRock AB350M-HDV/A320M-HDV/A320M-DGS Support CD

1 x I/O Panel Shield Because the motherboard specications and the BIOS soware might be updated, the content of this manual will be subject to change without notice. In case any modica-tions of this manual occur, the updated version will be available on ASRock’s website without further notice. If you require technical support related to this motherboard, please visit our website for specic information about the model you are using. You may nd the latest VGA cards and CPU support list on ASRock’s website as well. ASRock website http://www.asrock.com.English

Solid Capacitor design CPU

Supports AMD Socket AM4 A-Series APUs (Bristol Ridge) and Ryzen Series CPUs (Summit Ridge)

7 Power Phase design

Supports CPU up to 65W Chipset

Dual Channel DDR4 Memory Technology

• Please refer to Memory Support List on ASRock’s website for more information. (http://www.asrock.com/)

• Please refer to page 23 for DDR4 UDIMM maximum frequency support.

Max. capacity of system memory: 32GB

• Supports NVMe SSD as boot disks

Integrated AMD Radeon

Max. shared memory 2GB AB350M-HDV/A320M-HDV:

ree graphics output options: D-Sub, DVI-D and HDMIAB350M-HDV/A320M-HDV/A320M-DGS

Supports Triple Monitor

Supports HDMI with max. resolution up to 4K x 2K (4096x2160) @ 24Hz / (3840x2160) @ 30Hz

Supports DVI-D with max. resolution up to 1920x1200 @ 60Hz

Supports D-Sub with max. resolution up to 2048x1536 @ 60Hz

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI monitor is required)

Supports HDCP with DVI-D and HDMI Ports

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D and HDMI Ports A320M-DGS:

Supports DVI-D with max. resolution up to 1920x1200 @ 60Hz

Supports HDCP with DVI-D Port

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D Port Audio

• To congure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.

Supports Surge Protection

Supports Wake-On-LAN

Supports Lightning/ESD Protection

Supports LAN Cable Detection

Supports Energy Ecient Ethernet 802.3az

Supports PXE Rear Panel I/O

2 x USB 2.0 Ports (Supports ESD Protection)

4 x USB 3.0 Ports (Supports ESD Protection)

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

HD Audio Jacks: Line in / Front Speaker / MicrophoneEnglish

AB350M-HDV/A320M-HDV:

1 x DVI-D Port Storage

4 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0, RAID 1 and RAID 10), NCQ, AHCI and Hot Plug

1 x Ultra M.2 Socket, supports type 2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s) (with Ryzen Series CPU) or Gen3 x2 (16 Gb/s) (with A-Series APU)*

• Supports NVMe SSD as boot disks

• Supports ASRock U.2 Kit Connector

1 x Chassis Intrusion and Speaker Header

1 x CPU Fan Connector (4-pin)

2 x Chassis Fan Connectors (1 x 4-pin, 1 x 3-pin)

• e CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.

1 x Front Panel Audio Connector

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD Protection)

1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports ESD Protection) BIOS Feature

AMI UEFI Legal BIOS with GUI support

Supports “Plug and Play”

ACPI 5.1 compliance wake up events

DRAM Voltage multi-adjustmentAB350M-HDV/A320M-HDV/A320M-DGS

• For detailed product information, please visit our website: http://www.asrock.com Hardware Monitor

CPU/Chassis temperature sensing

CPU/Chassis Quiet Fan

CPU/Chassis Fan multi-speed control

ErP/EuP ready (ErP/EuP ready power supply is required) Please realize that there is a certain risk involved with overclocking, including adjust- ing the setting in the BIOS, applying Untied Overclocking Technology, or using third- party overclocking tools. Overclocking may aect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.English

is is a Micro ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it. Pre-installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.

In order to avoid damage from static electricity to the motherboard’s components, NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over- tighten the screws! Doing so may damage the motherboard.

Chapter 2 InstallationAB350M-HDV/A320M-HDV/A320M-DGS

2.1 Installing the CPU

Unplug all power cables before installing the CPU.

3AB350M-HDV/A320M-HDV/A320M-DGS

2.2 Installing the CPU Fan and Heatsink

Aer you install the CPU into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. Installing the CPU Box Cooler SR1 Please turn o the power or remove the power cord before changing a CPU or heatsink.

4-pin FAN cableAB350M-HDV/A320M-HDV/A320M-DGS

3AB350M-HDV/A320M-HDV/A320M-DGS

English 4-pin FAN cable

2AB350M-HDV/A320M-HDV/A320M-DGS

CPU_ FAN1 Please note that this connector is the interface to the LED control board on the SR3, it requires the AMD utility "SR3 Settings Soware" to control the LED. *e diagram shown here are for reference only. Please refer to page 28 for the orientation of USB Header.

English Please note that this connector is the interface to the LED control board on the SR3, it requires the AMD utility "SR3 Settings Soware" to control the LED. *e diagram shown here are for reference only. Please refer to page 28 for the orientation of USB Header.

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology. DDR4 UDIMM Maximum Frequency Support A-Series APUs: Ryzen CPUs: SR: Single rank DIMM, 1Rx4 or 1Rx8 on DIMM module label DR: Dual rank DIMM, 2Rx4 or 2Rx8 on DIMM module label 1. For dual channel conguration, you always need to install identical (the same brand, speed, size and chip-type) DDR4 DIMM pairs. 2. It is unable to activate Dual Channel Memory Technology with only one memory module installed.3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged. UDIMM Memory Slot Frequency (Mhz) A1 B1 - SR 2400 SR - 2400 - DR 2400 DR - 2400 SR SR 2400 DR DR 2400 UDIMM Memory Slot Frequency (Mhz) A1 B1 - SR 2667 SR - 2667 - DR 2667 DR - 2667 SR SR 2667 DR DR 2667English

e DIMM only ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

3AB350M-HDV/A320M-HDV/A320M-DGS

ere are 2 PCI Express slots on the motherboard. PCIe slots: PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

• PCIE2 will downgrade to x8 mode when A-Series APU is installed. Before installing an expansion card, please make sure that the power supply is switched o or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.English

e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (CLRCMOS1) (see p.1, 2, No. 12) CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right aer you update the BIOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default prole will be cleared only if the CMOS battery is removed. If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status. Clear CMOSDefaultAB350M-HDV/A320M-HDV/A320M-DGS

2.6 Onboard Headers and Connectors

System Panel Header (9-pin PANEL1) (see p.1, 2, No. 13) Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may congure the way to turn o your system using the power switch. RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. PLED (System Power LED): Connect to the power status indicator on the chassis front panel. e LED is on when the system is operating. e LED keeps blinking when the system is in S3 sleep state. e LED is o when the system is in S4 sleep state or powered o (S5). HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. e LED is on when the hard drive is reading or writing data. e front panel design may dier by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assign- ments and the pin assignments are matched correctly. Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.

GNDR ESET#PWRBTN#PLED-PLED+GNDHDLED-HDLED+

Chassis Intrusion and Speaker Header (7-pin SPK_CI1) (see p.1, 2, No. 14) Please connect the chassis intrusion and the chassis speaker to this header. Serial ATA3 Connectors (SATA3_1: see p.1, 2, No. 10) (SATA3_2: see p.1, 2, No. 11) (SATA3_3: see p.1, 2, No. 8) (SATA3_4: see p.1, 2, No. 9) ese four SATA3 connectors support SATA data cables for internal storage devices with up to

6.0 Gb/s data transfer rate.

USB 2.0 Header (9-pin USB_3_4) (see p.1, 2, No. 6) (9-pin USB_5_6) (see p.1, 2, No. 7) Besides two USB 2.0 ports on the I/O panel, there are two headers on this motherboard. Each USB

2.0 header can support

two ports. USB 3.0 Header (19-pin USB3_5_6) (see p.1, 2, No. 5) Besides four USB 3.0 ports on the I/O panel, there is one header on this motherboard. Each USB

3.0 header can support

two ports. Front Panel Audio Header (9-pin HD_AUDIO1) (see p.1, 2, No. 18) is header is for connecting audio devices to the front audio panel. SATA3_3 SATA3_4 SATA3_2 SATA3_1

1AB350M-HDV/A320M-HDV/A320M-DGS

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must

support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by

the steps below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to con- nect them for the AC’97 audio panel. E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”. Chassis and Power Fan Connectors (4-pin CHA_FAN1) (see p.1, 2, No. 20) (3-pin CHA_FAN2) (see p.1, 2, No. 15) Please connect fan cables to the fan connectors and match the black wire to the ground pin. CPU Fan Connector (4-pin CPU_FAN1) (see p.1, 2, No. 2) is motherboard pro- vides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3. ATX Power Connector (24-pin ATXPWR1) (see p.1, 2, No. 4) is motherboard pro- vides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin

ATX 12V Power Connector (4-pin ATX12V1) (see p.1, 2, No. 1) Please connect an ATX 12V power supply to this connector. Serial Port Header (9-pin COM1) (see p.1, 2, No. 17) is COM1 header supports a serial port module. TPM Header (17-pin TPMS1) (see p.1, 2, No. 19) is connector supports Trusted Platform Module (TPM) system, which can securely store keys, digital certicates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. Print Port Header (25-pin LPT1) (see p.1, 2, No. 16) is is an interface for print port cable that allows convenient connection of printer devices. CCTS#1RRTS#1DDSR#1DDTR#1RRXD1GNDTTXD1DDCD#1

SLCTAB350M-HDV/A320M-HDV/A320M-DGS

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The Ultra M.2 Socket (M2_1) supports SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s) (with Ryzen CPU) or Gen3 x2 (16 Gb/s) (with A-Series APU) Installing the M.2_SSD (NGFF) Module Step 1 Prepare a M.2_SSD (NGFF) module and the screw.

ABC Step 3 Move the stando based on the module type and length. e stando is placed at the nut location D by default. Skip Step 3 and 4 and go straight to Step 5 if you are going to use the default nut. Otherwise, release the stando by hand. ABC Step 4 Peel o the yellow protective lm on the nut to be used. Hand tighten the stando into the desired nut location on the motherboard. Step 5 Align and gently insert the M.2 (NGFF) SSD module into the M.2 slot. Please be aware that the M.2 (NGFF) SSD module only ts in one orientation. ABC ABC

oAB350M-HDV/A320M-HDV/A320M-DGS

Step 6 Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw as this might damage the module.English

Deutsch AB350M-HDV/A320M-HDV:

AMD Promontory A320 (A320M-HDV/A320M-DGS) Mémoire

1 x port DVI-D Stockage

Supporto WOL (Wake-On-LAN)

Supporto Energy Ecient Ethernet 802.3az

1 x porta DVI-D Archiviazi- one

Supporta “Plug and Play”

AB350M-HDV/A320M-HDV:

1 x Porta HDMIAB350M-HDV/A320M-HDV/A320M-DGS

AB350M-HDV/A320M-HDV:

负责。AB350M-HDV/A320M-HDV/A320M-DGS

Kipas Hening CPU/Sasis

EN 55024: 1998 + A1:2001 + A2:2003 IEC 61000-4-2: 2008; IEC 61000-4-3: 2010; IEC 61000-4-4: 2010; IEC 61000-4-5: 2005; IEC 61000-4-6: 2008; IEC 61000-4-8: 2009; IEC 61000-4-11: 2004;

e following manufacturer / importer or authorized representative established within the EUT is responsible for this declaration: ASRock EUROPE B.V. (Company Name) Bijsterhuizen 1111 6546 AR Nijmegen e Netherlands (Company Address) Person responsible for making this declaration: (Name, Surname) A.V.P (Position / Title) March 17, 2017 (Date) P/N: 15G062027000AK V1.0