TS 200 FC - Lamp Cameo - Free user manual and instructions

USER MANUAL TS 200 FC Cameo

TS 200 FC THEATER SPOT WITH FRESNEL LENS AND 200W 6-IN-1 LED

SETUP AND INSTALLATION 11

DMX TECHNOLOGY 11 TECHNICAL SPECIFICATIONS 12

MANUFACTURER’S DECLARATIONS 13

CONTROLLO DMX 693 DMX DEUTSCHFRANCAIS ESPAÑOL ENGLISH ITALIANO POLSKI ENGLISH YOU‘VE MADE THE RIGHT CHOICE! We have designed this product to operate reliably over many years. Please read this User‘s Manual carefully, so that you can begin making optimum use of your Cameo Light product quickly. Learn more about Cameo Light on our website WWW.CAMEOLIGHT.COM. PREVENTIVE MEASURES

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observ e the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. This appliance is designed exclusively for indoor use, do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment - in this case, observe the special instructions noted below). Do not expose this equipment to flammable materials, fluids or gases. 12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with liquids, such as vases or drinking vessels, on the equipment.

13. Make certain that objects cannot fall into the device.

14. Use this equipment only with the accessories recommended and intended by the manufacturer.

15. Do not open or modify this equipment.

16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards. 17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries. 18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.

19. Clean the equipment using a dry cloth.

20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.

21. Plastic bags must be kept out of reach of children.

FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS: 22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord. 23. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature. 24. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician. 25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power adapter and the equipment connector. 26. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands. 27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the equipment. 28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorised service centre. 29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet. 30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be re- moved. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables. 31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

32. The device must only be installed in a voltage-free condition (disconnect the mains plug from the mains).

33. Dust and other debris inside the unit may cause damage. The unit should be regularly serviced or cleaned (no guarantee) depending on ambient conditions (dust etc., nicotine, fog) by qualified personnel to prevent overheating and malfunction.

34. Please keep a distance of at least 0.5 m to any combustible materials.

35. Power cables to power multiple devices must have a cross-section of at least 1.5 mm². Within the EU, the cables must correspond to H05VV-F, or similar. Suitable cables are offered by Adam Hall. With these cables, you can connect multiple devices via the power OUT connection to the power IN connection of an additional device. Make sure that the total current consumption of all connected devices does not exceed the specified value on all connected devices (label on the device). Make sure to keep power cable connections as short as possible.4 DMX ITALIANO POLSKI ESPAÑOL FRANCAIS DEUTSCHENGLISH 36. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

37. Children must be instructed not to play with the device.

38. If the power cord of the device is damaged, do not use the device. The power cord must be replaced by an adequate cable or assembly from an authorized service center. CAUTION: To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts inside. Maintenance and repairs should be exclusively carried out by qualified service personnel. The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an electrical shock. The warning triangle with exclamation mark indicates important operating and maintenance instructions. Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait for a cool-down period of at least 10 minutes before handling or transporting the device. Warning! This device is designed for use below 2000 metres in altitude. Warning! This product is not intended for use in tropical climates. Caution! Intense LED light source! Risk of eye damage. Do not look into the light source. CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS! 1. The product has been developed for professional use in the field of event technology and is not suitable as household lighting.

2. Do not stare, even temporarily, directly into the light beam.

3. Do not look at the beam directly with optical instruments such as magnifiers.

4. Stroboscope effects may cause epileptic seizures in sensitive people! People with epilepsy should definitely avoid places where strobes are used.5 DMX DEUTSCHFRANCAIS ESPAÑOL ENGLISH ITALIANO POLSKI

POWER OUT White Power Twist power socket for the power supply of additional CAMEO spotlights. Ensure that the total power consumption of all devic- es connected to the device does not exceed the given ampere (A) value.

FUSE Fuse holder for 5 x 20 mm micro fuses. IMPORTANT NOTE: Exclusively replace the fuse with a fuse of the same type and same values (T3A/250 V). If a fuse trips repeatedly, please contact an authorized service center.

DMX IN Male 3-pin and 5-pin XLR connectors to connect a DMX control device.

DMX OUT Female 3-pin and 5-pin XLR connectors to transmit the DMX control signal.

Display for the currently active mode and the menu items in the processing menu. INTRODUCTION

FRESNEL THEATER SPOT RGBALC

CLTS200FC CONTROL FUNCTIONS 1-channel, 3-channel 1, 3-channel 2 HSI, 3-channel 3 CCT, 6-channel direct, 12-channel HSI, 14-channel direct DMX control RDM-enabled Master/slave mode Stand-alone functions: PROPERTIES 200 W RGBALC LED. Fresnel lens. Continuous manual zoom. Multifunctional strobe. Flicker-free projection. 3- and 5-pin DMX connectors. Barn door and color filter frame included. 100–240 V AC operating voltage. 200 W power consumption. The spotlight complies with the RDM standard (Remote Device Management). Remote device management allows the user to view the status and configuration of RDM terminals via an RDM-enabled controller.

CONNECTIONS, CONTROL, AND DISPLAY ELEMENTS

CONTROL KEYS MENU – access the options menu for system settings by pressing MENU. Pressing it again will return you to the main screen. ENTER – lets you change a value and confirm changes to values. UP and DOWN – select the individual menu items in the options menu and in the submenu (mode, system information, etc.). Changes a value, for example, the DMX address. Press MENU and ENTER at the same time to access the last edited menu item.

ZOOM Knurled knob for adjusting the size of the light beam (adjusted fully to the right= minimum light beam size, adjusted fully to the left = maximum light beam size).

SAFETY EYEBOLT Safety eyebolt for securing the spotlight on crossbeam installations. OPERATION NOTE: As soon as the spotlight is correctly connected to the power, various pieces of information will appear on the display during startup: “Update Wait...” (only for servicing purposes), “WELCOME TO Cameo”, the model number, and the software version. The spotlight is ready after this process, and the mode that was previously selected will activate.

MAIN SCREEN DMX MODE

The upper row on the display shows “DMX Addr” and the bottom line shows the currently set DMX start address. As soon as the DMX signal is interrupted, the display begins to flash. Once the DMX signal is restored, it stops flashing. If there is no input within approx. 30 seconds, the main screen is automatically activated.

MAIN SCREEN STAND-ALONE MODE

The bottom row on the display shows the currently active stand-alone mode (Slave, Auto, Macro, HSI, CCT, Direct). If there is no input within approx. 30 seconds, the main screen is automatically activated.7 DMX DEUTSCHFRANCAIS ESPAÑOL ENGLISH ITALIANO POLSKI

CONFIGURING DMX MODE

You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “DMX Addr” menu item (bottom row) and confirm via ENTER. You can now set the DMX start address as desired using UP and DOWN (hold down to quickly change values, highest value depends on the activated DMX mode). Confirm your input via ENTER and press MENU once to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. If the main screen is activated, it is possible to change the DMX start address directly (UP and DOWN buttons).

CONFIGURING DMX MODE

You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Mode” menu item (bottom row) and confirm via ENTER. Using the UP and DOWN buttons again, select the “DMX” menu item and confirm via ENTER. You can now select the desired DMX mode using UP and DOWN and then press ENTER to confirm your selection. Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. You can find tables on channel assignment in the different DMX modes in these instructions under DMX CONTROL. SLAVE MODE You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Mode” menu item (bottom row) and confirm via ENTER. Using the UP and DOWN buttons again, select the “Slave” menu item and confirm via ENTER. Connect the slave and master unit (same model, same software version) using a DMX cable, and activate one of the stand-alone modes (Auto, Macro, HSI, CCT, Direct) on the master unit. The slave unit will now follow the master unit. Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. STAND-ALONE MODE AUTOMATIC CONTROL (Auto) Stand-alone mode for selecting an auto program (Program) and for setting the brightness (Dimmer) and speed (Speed). You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Mode” menu item (bottom row) and confirm via ENTER. Afterwards, select the “Auto” menu item by using the UP and DOWN buttons again. Confirm with ENTER. Now use UP and DOWN to select the submenu item you’d like to edit and then press ENTER. Set the desired value by pressing UP and DOWN (hold down to quickly change values) and confirm via ENTER. Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. If the main screen is activated, the overall brightness (dimmer) can now be set directly (UP and DOWN buttons). Six different audio programs are available: Auto program 7ColJum = 7 color jumping 7ColFad = 7 color fading 15ColJum = 15 color jumping 15ColFad = 15 color fading RandJump = Random jumping RandFade = Random fading8 DMX ITALIANO POLSKI ESPAÑOL FRANCAIS DEUTSCHENGLISH STAND-ALONE MODE COLOR MACROS (Macro) Stand-alone mode for selecting a color preset (Color), for setting the brightness (Dimmer), and the stroboscope (Speed). You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Mode” menu item (bottom row) and confirm via ENTER. Afterwards, select the “Macro” menu item by using the UP and DOWN buttons again. Confirm with ENTER. Now use UP and DOWN to select the submenu item you’d like to edit and then press ENTER. Set the desired value by pressing UP and DOWN (hold down to quickly change values) and confirm via ENTER. The values for setting the stroboscopic function correspond to the values of the multifunctional stroboscope in channel 3 of the 12- and 14-channel DMX mode. Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. If the main screen is activated, the overall brightness (dimmer) can now be set directly (UP and DOWN buttons). Fifteen color macros are available: Macro Red Turquoise Magenta Amber Cyan Pink Yellow Warm Blue Warm White Yellow Lavender White Green Mauve Cold White STAND-ALONE MODE HSI (Hue saturation intensity) Stand-alone mode for setting the hue (Hue), color saturation (Saturation), brightness (Intensity), and stroboscope (Strobe). You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Mode” menu item (bottom row) and confirm via ENTER. Afterwards, select the “HSI” menu item by using the UP and DOWN buttons again. Confirm with ENTER. Now use UP and DOWN to select the submenu item you’d like to edit and then press ENTER. Set the desired value by pressing UP and DOWN (hold down to quickly change values) and confirm via ENTER. The values for setting the stroboscopic function correspond to the values of the multifunctional stroboscope in channel 3 of the 12- and 14-channel DMX mode. Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. If the main screen is activated, the overall brightness (intensity) can now be set directly (UP and DOWN buttons). STAND-ALONE MODE CCT (Correlated Color Temperature) Stand-alone mode for setting the color temperature (Temperature), tint (Tint), brightness (Dimmer), and stroboscope (Strobe). You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Mode” menu item (bottom row) and confirm via ENTER. Afterwards, select the “HSI” menu item by using the UP and DOWN buttons again. Confirm with ENTER. Now use UP and DOWN to select the submenu item you’d like to edit and then press ENTER. Set the desired value by pressing UP and DOWN (hold down to quickly change values) and confirm via ENTER. The values for setting the stroboscopic function correspond to the values of the multifunctional stroboscope in channel 3 of the 12- and 14-channel DMX mode. Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. If the main screen is activated, the overall brightness (dimmer) can now be set directly (UP and DOWN buttons).9 DMX DEUTSCHFRANCAIS ESPAÑOL ENGLISH ITALIANO POLSKI STAND-ALONE MODE DIRECT (Direct) Stand-alone for setting the overall brightness (Dimmer), the stroboscope (Strobe), and the color mixing of R, G, B, A, L, and C (Red, Green, Blue, Amber, Lime, Cyan). You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Mode” menu item (bottom row) and confirm via ENTER. Afterwards, select the “Direct” menu item by using the UP and DOWN buttons again. Confirm with ENTER. Now use UP and DOWN to select the submenu item you’d like to edit and then press ENTER. Set the desired value by pressing UP and DOWN (hold down to quickly change values) and confirm via ENTER. Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. If the main screen is activated, the overall brightness (dimmer) can now be set directly (UP and DOWN buttons). DEVICE SETTINGS You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Settings” menu item and confirm via ENTER. This will take you to the submenu for setting the submenu items (see table, select via UP and DOWN, confirm via ENTER, change status via UP and DOWN, confirm via ENTER): Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. Settings (bold = factory setting) DispBack = Display backlight Backlight on Permanently on Backlight off Deactivates after approx. 30 seconds of inactivity DMX Fail = Operating mode for DMX signal interruption Hold Last DMX command is retained Blackout Activates blackout Fan = Adjust fan control Auto Automatic fan speed control Silent Extra quiet fan (with reduced brightness, if required) RedShift = Imitates color drift of a halogen spotlight when dimming. The dimming of the spotlight automatically changes the color temperature along a rising curve of warm white and amber (and vice-versa). On Color drift activated Off Color drift deactivated DimCurve = Dimmer curve Linear Light intensity increases linearly with DMX value Expo Light intensity can be finely adjusted at lower DMX values and broadly adjusted at higher DMX values Log Light intensity can be broadly adjusted at lower DMX values and finely adjusted at higher DMX values S-curve Light intensity can be finely adjusted at lower and higher DMX values, and broadly adjusted at medium DMX values10 DMX ITALIANO POLSKI ESPAÑOL FRANCAIS DEUTSCHENGLISH DimResp = Dimmer response LED The LED spotlight responds abruptly to changes in the DMX value Halogen The spotlight behaves like a halogen spotlight with soft changes in brightness PWM = LED PWM frequency 650 Hz Sets the LED PWM frequency 1530 Hz 3600 Hz 12 kHz 25 kHz FacReset = Reset to factory settings No Do not reset (confirm via ENTER) Yes Implement reset (confirm via ENTER) Calibrate = Individual color calibration R, G, B, A, L, C Multimode calibration of red, green, blue, amber, lime, and cyan colors with values from 000 to 255 DEVICE INFORMATION You can access the options menu by pressing MENU. Using the UP and DOWN buttons, now select the “Sys Info” menu item and confirm via ENTER. This will take you to the submenu for displaying the device information. Use the UP and DOWN buttons again to select the desired submenu item and then access the information by pressing ENTER (see table). Press MENU again to return to the main screen. If there is no input within approx. 30 seconds, the main screen is automatically activated. Sys Info Temp = Displays temperature of LED unit Temp LED xxx °C / xxx °F Temp C°/F° °C (= displays in degrees Celsius) °F (= displays in degrees Fahrenheit) Op. Hours = Operating time display Op. hours x:xx h Displays the total operating time in hours and minutes Firmware = Displays the device software version Firmware V1.xx11 DMX DEUTSCHFRANCAIS ESPAÑOL ENGLISH ITALIANO POLSKI DMX TECHNOLOGY DMX-512 DMX (Digital Multiplex) is the designation for a universal transmission protocol for communications between corresponding devices and controllers. A DMX controller sends DMX data to the connected DMX device(s). The DMX data is always transmitted as a serial data stream that is forwarded from one connected device to the next via the "DMX IN" and "DMX OUT" connectors (XLR plug-type connectors) that are found on every DMX-capable device, provided the maximum number of devices does not exceed 32 units. The last device in the chain needs to be equipped with a terminator (terminating resistor). DMX CONNECTION DMX is the common "language" via which a very wide range of types and models of equipment from various manufacturers can be connected with one another and controlled via a central controller, provided that all of the devices and the controller are DMX compatible. For optimum data transmission, it is necessary to keep the connecting cables between the individual devices as short as possible. The order in which the devices are integrated in the DMX network has no influence on the addresses. Thus the device with the DMX address 1 can be located at any position in the (serial) DMX chain: at the beginning, at the end or somewhere in the middle. If the DMX address 1 is assigned to a device, the controller "knows" that it should send all data allocated to address 1 to this device regardless of its position in the DMX network.

SERIAL CONNECTION OF MULTIPLE LIGHTS

1. Connect the male XLR connector (3-pin or 5-pin) of the DMX cable to the DMX output (female XLR socket) of the first DMX device (e.g. DMX-Controller). 2. Connect the female 3-pin XLR connector of the DMX cable connected to the first projector to the DMX input (male 3-pin socket) of the next DMX device. In the same way, connect the DMX output of this device to the DMX input of the next device and repeat until all devices have been connected. Please note that as a rule, DMX devices are connected in series and connections cannot be shared without active splitters. The maximum number of DMX devices in a DMX chain should not exceed 32 units.

SETUP AND INSTALLATION

Thanks to its four rubber feet, the spotlight can be placed in a suitable location on a flat surface. Install on a crossbeam using the prein- stalled mounting bracket (A) and a suitable crossbeam clamp (available as an accessory). Make sure that the spotlight is firmly attached and secure it using a suitable safety cable on the provided safety eyebolt (B). Use the laterally mounted level screw (C) to configure the vertical beam angle. Important info: Overhead installation requires extensive experience, which includes calculating the limit values of the work- ing load, of the installation material to be used, and regularly conducting safety inspections of all installation materials and spotlights. If you do not have these qualifications, do not attempt to carry out the installation yourself; contact a professional company.12 DMX ITALIANO POLSKI ESPAÑOL FRANCAIS DEUTSCHENGLISH The Adam Hall 3 STAR, 4 STAR, and 5 STAR product ranges include an extensive selection of suitable cables. DMX CABLES When fabricating your own cables, always observe the illustrations on this page. Never connect the shielding of the cable to the ground contact of the plug, and always make certain that the shielding does not come into contact with the housing of the XLR plug. If the shielding is connected to the ground, this can lead to short-circuiting and system malfunctions. Pin Assignment DMX cable with 3-pin XLR connectors: DMX cable with 5-pin XLR connectors (pin 4 and 5 are not used): Shield

Shield DMX TERMINATORS (TERMINATING RESISTORS) To prevent system errors, the last device in a DMX chain needs to be equipped with a terminating resistor (120 ohm, 1/4 Watt). 3-pin XLR connector with a terminating resistor: K3DMXT3 5-pin XLR connector with a terminating resistor: K3DMXT5 Pin Assignment 3-pin XLR connector: 5-pin XLR connector:

DMX ADAPTER The combination of DMX devices with 3-pin connectors and DMX devices with 5-pin connectors in a DMX chain is possible with suitable adapters. Pin Assignment DMX Adapter 5-pin XLR male to 3-pin XLR female: K3DGF0020 Pins 4 and 5 are not used. Pin Assignment DMX Adapter 3-pin XLR male to 5-pin XLR female: K3DHM0020 Pins 4 and 5 are not used. TECHNICAL SPECIFICATIONS Model number: CLTS200FC Product type: LED Spotlight Type: Fresnel theater spot with zoom function Color spectrum: RBGALC CRI (CCT Modus) > 90 Number of LEDs: 1 LED type: 200 W LED PWM frequency: 650 Hz, 1530 Hz, 3600 Hz, 12 kHz, 25 kHz (confi gurable) Beam angle (half peak angle) 13 ° – 49 ° DMX input: 3-pin and 5-pin XLR, male DMX output: 3-pin and 5-pin XLR, female DMX color functions: Direct, HSI, CCT DMX functions: Dimmer, fi ne dimmer, stroboscope, red, green, blue, amber, lime, cyan, color macros, CCT, tint, hue, saturation, device setting13 DMX DEUTSCHFRANCAIS ESPAÑOL ENGLISH ITALIANO POLSKI Controller: DMX512, RDM-enabled Standalone functions: Direct, HSI, CCT, color macros, master/slave Control elements: Menu, enter, up, down, zoom Display elements: Illuminated 2-line LC display Operating voltage: 100 – 240 V AC / 50 – 60 Hz Power consumption: 200 W Illumination intensity (@ 1 m): 34000 lx @ 13 ° Luminous flux: 5300 lm Power supply connection: INPUT: Blue Power Twist power socket OUTPUT: White Power Twist power socket (max. 8 A) Fuse: T3 A / 250 V (5 x 20 mm) Ambient temperature (running): 32 °F to 104 °F Relative humidity: < 80 %, non-condensing Housing material: Cast metal Housing color: Black Housing cooling: Temperature-controlled fan Dimensions (W x H x D, without mounting bracket):

12.6 x 14.6 x 12.2 inches

Weight: 17.9 lbs Additional features: Filter frame, barn door, and mounting bracket included in product contents, manual zoom

MANUFACTURER´S DECLARATIONS

CORRECT DISPOSAL OF THIS PRODUCT

(valid in the European Union and other European countries with a differentiated waste collection system) This symbol on the product, or on its documents indicates that the device may not be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased this product, or their local government office, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste for disposal. FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation CE Compliance Adam Hall GmbH states that this product meets the following guidelines (where applicable): R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017 Low voltage directive (2014/35/EU) EMV directive (2014/30/EU) RoHS (2011/65/EU) The complete declaration of conformity can be found at www.adamhall.com. Furthermore, you may also direct your enquiry to [e-mail].14 DMX ITALIANO POLSKI ESPAÑOL FRANCAIS DEUTSCHENGLISH DEUTSCH SIE HABEN DIE RICHTIGE WAHL GETROFFEN! Dieses Gerät wurde unter hohen Qualitätsanforderungen entwickelt und gefertigt, um viele Jahre einen reibungslosen Betrieb zu gewähr- leisten. Bitte lesen Sie diese Bedienungsanleitung sorgfältig, damit Sie Ihr neues Produkt von Cameo Light schnell und optimal einsetzen können. Weitere Informationen über Cameo Light erhalten Sie auf unserer Website WWW.CAMEOLIGHT.COM. SICHERHEITSHINWEISE

FRESNEL THEATER SPOT RGBALC

006 - 010 Strobe closed

103 - 127 Strobe break effect, 5s…..1s (short burst with break)

Transition Time between Color Modes

006 - 105 0,1s - 10s (0,1s Steps)

106 - 214 11s - 119s (1s Steps)

215 - 244 2m - 4m50s (10s Steps)

Device settings (please read remark 1*)

006 - 010 Strobe closed

103 - 127 Strobe break effect, 5s…..1s (short burst with break)

CCT (overides RGBALC)

Transition Time between Color Modes

006 - 105 0,1s - 10s (0,1s Steps)

106 - 214 11s - 119s (1s Steps)

215 - 244 2m - 4m50s (10s Steps)

Device settings (please read remark 1*)