GS 1102 PI - Water pump Güde - Free user manual and instructions

Product type	Submersible water pump
Brand	Güde
Model	GS 1102 PI
Power supply	230 V / 50 Hz
Motor power P1	1100 W
Max flow rate	20,000 l/h
Max delivery head	8 m
Max submersion depth	7 m
Discharge connection	1 1/2"
Protection rating	IPX8
Max water temperature	35 °C
Max particle size	35 mm
Power cable length	10 m (type H07RNF)
Float switch	Yes, adjustable
Thermal protection	Yes, with automatic reset
Application area	Clean water and dirty water
Main functions	Draining, evacuation, dewatering
Maintenance	Rinse with clean water after use
Cleaning	Clean suction strainer regularly
Safety	30 mA residual current device required
Housing material	Synthetic (estimated)
Package contents	Pump, handle, connection, float switch, cable
Warranty	24 months for private use, 12 months for professional use

Frequently Asked Questions - GS 1102 PI Güde

How to install the GS 1102 PI pump?

Connect a 1 1/2 inch hose to the outlet. Attach a rope to the handle and submerge the pump at an angle to release air. Plug it into an outlet with a 30 mA residual current device.

What is the maximum submersion depth?

The maximum submersion depth is 7 meters.

What to do if the pump does not start?

Check the mains voltage. Make sure the impeller is not blocked by debris. Ensure the float switch is not in the off position.

How to adjust the float switch?

The float cable can be shortened or lengthened on the handle. The shorter the cable, the higher the switch-on level. Ensure the float can move freely.

Can hot water be pumped?

The maximum pumped water temperature is 35 °C. Above this, the pump may be damaged.

How to maintain the pump?

After each use, rinse the pump with clean water to remove residues. Clean the suction strainer regularly to prevent clogging.

Can the pump run dry?

No, the pump must never run dry. It must always be fully submerged to avoid damage to the seal and motor.

What are the electrical hazards?

Use a 30 mA residual current device without fail. Never touch the plugged-in pump with wet hands. The cable must be in good condition.

What to do if the thermal cut-out trips?

Wait about 25 minutes for the motor to cool down. The pump restarts automatically. If the problem persists, check for clogging or water temperature.

Can the pump be used for a swimming pool?

Yes, but no one should be in the water during operation. The pump must be installed according to safety standards.

USER MANUAL GS 1102 PI Güde

Translation of original operating instructions

DIRTY-WATER SUBMERSIBLE PUMP

Francais FR 12

Please read carefully the following Operating Instructions before putting the appliance into operation

A.V. 2 Any reprints, even partial, are subject to approval. Technical changes reserved. Illustrative pictures! Translation of original operating instructions.

Marking:

Product safety:

CE
Product corresponds to appropriate norms of the European Community

Prohibitions:

Staying in the transportation medium prohibited	Access to children prohibited
	>35°C
Cable bullying / transport prohibited	Transportation medium of max. 35 °C

Warning:

9
Warning against dangerous electric voltage	Warning against automatic starting

Commands:

Read the Operating Instructions

Environment protection:

	PAP
Dispose the waste professionally in order not to pollute the environment.	Packing cardboard material may be delivered to collecting centres for recycling.
Any damaged or disposed electric or electronic devices must be delivered to appropriate collection centres.

Package:

J	II
Protect against humidity This side up

Disposal

Disposal instructions are illustrated in the form of pictograms on the device or packaging. Description of the pictograms is given in "Identification" chapter.

Disposal of transport packaging

Packaging protects the device against damage during transport. Packaging materials are usually selected according

to their effect on environment and disposal methods and can therefore be recycled.

Returning of the packaging back to circulation saves resources and costs for packaging disposal. Parts of the packaging (e.g. foil, styropor) may be dangerous for children. Risk of suffocation!

Keep these parts of the packaging out of reach of children and dispose as soon as possible.

Appliance

GS 1102 PI

Permanent use. Cable RNF 10 m long. Float automatics

Areas of Use: To pump/pump out water - clean and dirt - from sewers, tanks etc.

Supply includes (pic. A)

1. Carrying handle
2. Pump connection
3. Electric cable
4. Foot
5. Connecting neck of the pump
6. Floating switch
7. Pump cover/body

Warranty

A warranty period of 12 months applies to commercial use and 24 months apply to private use and commences on the day of purchase of the device.

Warranty applies exclusively to failures due to defective material or workmanship. An original sale slip with indication of date of sale must be presented in case of claiming for the warranty rights.

Warranty does not cover unprofessional use such as device overload, violent use, damage caused by third party or foreign materials, failure to comply with operations and assembly manual, and normal wear and tear.

General safety instructions

The Operating Instructions need to be read thoroughly before first use of the appliance. If there are any doubts concerning appliance connection and handling, please contact the producer (service department).

TO ENSURE HIGH SAFETY LEVEL, FOLLOW CAREFULLY THE FOLLOWING INSTRUCTIONS:

Attention: Operation is only allowed with a safety switch against stray current (max. stray current of 30mA according to VDE regulation, part 702). Please ask your electrician.

Attention: The pump must not in any case run without fillings. The pump must work fully plunged in liquid.

• The user is responsible to third parties if pump (dumping stations, etc.) is used.
• Operate it only on connections with a safety switch against stray current (FI)!

• Before putting into operation, a qualified electrician must check whether electric safety measures required are in place.
  Electric connection to a socket.

• Check the voltage. Technical data given on the type label must correspond with electric network voltage.

• If the pump is used in ponds, wells, etc. and appropriate pumping stations, standards valid for pumps in the given country must unconditionally be observed.
• Pumps used outdoors (e.g. in ponds, etc.) must be equipped with a H07RNF type rubber connecting cable, according to DIN 57282 or DIN 57245 standards.
• If the pump is in operation, neither people nor animals can be present or plunged in the pumped liquid (e.g. pools, cellars, etc.).
• The temperature of the drained liquid must not exceed +35^ircC . If an extension cable is used, it must solely be out of rubber, H07RNF type, according to DIN 57282 or DIN 57245 standards. Never touch, lift or carry with a cable a pump connected to network. It is necessary to make sure the connecting socket was not near water and humidity and the plug was protected against humidity.
• Before putting the pump into operation, check whether the electric cable and/or socket are not damaged.
• Before any work on the pump, pull the plug out of the socket.
• If the pump is inbuilt in a floor outlet, the floor outlet must subsequently be covered to ensure inviolability of passers-by.
• Connection of the discharge pipe needs to be ensured with a hose clip (pic. F).
• Keep the max. plunge depth (see the technical data). To prevent damage (such as flooded rooms, etc.) as a result of faulty pump operation (failure or fault) the owner (user) is obliged to take reasonable safety measures (alarm assembly, spare pump, etc.). At sandy or muddy soils, it is necessary to let the pump run hanging on a rope or chains or put the pump on a reasonable support to prevent suction part falling.
• If the pump is faulty, the repair needs to be solely executed by an authorised service centre. Only original spare parts can be used.

• Let us refer to the fact we do not assume any responsibility - according to standards in force - for damage eventually caused by our appliances in the below-mentioned cases:

• Unprofessional repairs executed by unauthorised service centres;

• Use in conflict with the designed purpose, or failure to observe the use as designed;
• Pump overload with a continuous run;
• Damage as a result of icing or any other fault caused by climatic influences;

Identical regulations apply for accessory parts.

At any damage of the power supply cable of the appliance, please unconditionally contact the electrician. Under no circumstances, execute any repair with your hands.
This appliance is not designed to be used by persons (including children) with any bodily, sensory or mental restriction. Also persons with a lack of experience or knowledge of the appliance are not allowed to work with the appliance.
- Never let unauthorised and unattended persons, especially children, get near the appliance. Always keep children and unauthorised persons out of reach of the appliance.

The pump is not suitable for long-term operation (e.g. as a circulation pump in ponds or brooks). The service life gets shorter accordingly if the pump is used in this manner. In such

a case, use a switching clock and ensure sufficiently long breaks between the operating cycles.

The pump must not be connected to the existing water supply system as equipment increasing the pressure.
The pump is not suitable as a long-term, automatic safety against overflow of tanks and wells or for control of underground water in cellars.
Do not leave the pump unattended to prevent damage as a result of any faulty function. Always disconnect the pump from network if not used.

The producer does not guarantee for any damage caused by unqualified installation or unprofessional operation of the pump.

The equipment must be regularly inspected and its faultless condition needs to be checked.

Before each putting into operation, the pump must be visually inspected for any damage (especially on the power supply cable and plug). Using a damaged pump is strictly prohibited.

Connecting cable for drowned pumps

The drowned pumps are equipped with a 10-m H07RNF cable, depending on the type.

According to the valid regulation, drowned pumps with a connecting cable length of less than 10m can only be used indoors for water drainage from cellars.

Therefore the cable length and type need to be considered at purchasing.

Thermal fuse

A probe automatically switching the pump off when specific temperature is exceeded and on when the pump has cooled down is assembled inside the electric motor. That manifold increases the pump service life and prevents electric motor burn-out.

Procedure:

The pump is put into operation when the plug is inserted in appropriate socket and the floating switch is in the required position (see the Instructions). If the pump is lifted or transported, it is done with an assembled handle and not with the connecting cable. If the pump is being plunged, a rope, chain, etc. fastened to the handle need to be used if necessary.

At muddy, sandy or siliceous soil the pump must be hung on a rope or chain or put on a suitable wide baseplate to be able to work plunged. Sand and other abrasive solids reduce the service life of hydraulic parts and seal of the pump and therefore they need to be prevented. In frost conditions, the pump must be removed from the pumped liquid. It is necessary to absolutely make sure the pump is not exposed to a risk of frost. The pump must be emptied and stored at a place protected against frost.

Attention! Important information for the customer It is recommended to plunge or put the pump sideways in the liquid. The body air cushion can thus be released and the pump starts immediately working. The pump can subsequently be stood straight.
Attention! Important information for the customer To ensure long service life of the pump seal, we recommend rinsing the pump with clean water in regular intervals.

Automatic float

The float will automatically put the pump into operation when the liquid level goes up or down. If the float cable is extended or shortened, based on its support point, it will switch the pump on or off due to the minimum or maximum height required. The float cable is fixed to the pump handle with a suitable pressure holder. Please check whether the float is moving freely at pump operation. The pump must always be rinsed with clean water when used in very dirty water. The switching on and off heights can differ.

Thermal fuse/engine protection circuit-breaker

The drowned pump is equipped with an engine protection circuit-breaker. If the engine is overheated, the engine protection circuit-breaker will automatically switch the pump off. Cooling time is app. 25 minutes, the pump subsequently switches on. If the engine protection circuit-breaker switches on, it is absolutely necessary to identify the cause and remove it (see also the "Failure searching"). The given data cannot be used for "family style" repairs as it requires specific professional knowledge. You must contact the customer service department at any failures.

Residual risks and protective measures

Electric residual risks:

Threat	Description	Protective measure(s)
Direct electric contact	Electric shock	Safety switch against FI stray current
Indirect electric contact	Electric shock through medium	Safety switch against FI stray current

Requirements for operating staff

The operating staff must carefully read the Operating Instructions before using the appliance.

Qualification

Apart from the detailed instructions by a professional, no special qualification is necessary for appliance using.

Minimum age

Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education.

Training

Using the appliance only requires corresponding training by a professional or the Operating Instructions. No special training is necessary.

Technical data

GS 1102 PI
Voltage/Frequency 230 V / 50 Hz
Motor capacity P1 1100 W
Maximum delivered quantity 20000 l/h
Maximum head of delivery 8 m
Maximum immersion 7 m
Hose connection 1 1/2"
Protection class IPX8
Water temperature 35 °C
Granulation 35 mm
Max. suction 6,4 kg
Weight ca 94634

Transport and storage

At winter storing, it is necessary to make sure there is no water in the appliance as the frost could damage the appliance.

Safety instructions for first putting into operation

Attention: The pump must not run without fillings.

The user is responsible to third parties if pump (pumping station, etc.) is used.

To be operated on connections with a safety switch against stray current (RCD) only!

Before putting into operation, a competent electrician must check whether electric safety devices are in place.

Electric connection to a socket.

Check the voltage. Technical data given on the type label must correspond with electric network voltage.

If the pump is used in ponds, wells, etc. and appropriate pumping stations, standards valid for pumps in the given country must unconditionally be observed.

Electric pumps used outdoors (e.g. in ponds, etc.) must be equipped with a H07RNF type rubber connecting cable, according to DIN 57282 or DIN 57245 standards.

If the pump is in operation, neither people nor animals can be present or plunged in the pumped liquid (e.g. pools, cellars, etc.).

The temperature of the drained liquid must not exceed +35^ircC . If an extension cable is used, it must solely be out of rubber, H07RNF type, according to DIN 57282 or DIN 57245 standards.

Never touch, lift or carry with a cable a pump connected to network (pic. E)

It is necessary to make sure the connecting socket was not near water and humidity and the plug was protected against humidity.

Before putting the pump into operation, check whether the electric cable and/or socket are not damaged.

Before any work on the pump, pull the plug out of the socket.

Emergency Action

Apply the first aid adequate to the injury and get qualified medical assistance as quickly as possible. Protect the injured person from more accidents and calm him/her down.

For the sake of eventual accident, in accordance with DIN 13164, a workplace has to be fitted with a first-aid kit. It is essential to replace any used material in the first-aid kit immediately after it has been used. If you seek help, state the following pieces of information:

1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)

Instructions step by step

• Connect the water hose to appropriate pump outlet (see the Assembly and first putting into operation).
  Fix the rope, chain, etc. to the pump handle and place it to the right place.
• Put the pump "sideways" (pic. D) to the pumped medium. Make sure the floating switch is in the operating position.
  Plug in the pump.
• Rinse the pump with clean water after work finishing.

Floating switch positions (pic. B + C)

The operating or shutdown point of the pump can be set with various floating switch positions. In pic. B you can see the float cable without any fixation change with full switch radius. The figure 1 is the working position and figure 0 the shutdown position.

Due to appropriate fixation of the float cable, possible on the pump handle, the switch radius can be reduced when there is no sufficient space or at a corresponding level control.

The figure 1 in pic. C is the working position and figure 0 the shutdown position.

Failures - causes - removal

(problem): Engine does not start (cause):

1. No system voltage
2. Blocking pump wheel
3. Floating switch in shutdown position

(measures):

1. Check the voltage
2. Inspect the pump wheel for foreign objects
3. Check the water level (pic. B/C)

(problem): Pump does not suck (cause):

1. Pump without water
2. Water level too low
3. Restricted pump wheel

(measures):

1. Let the air bubbles release (pic. D)
2. Switch the pump off, water level must go up.
3. Remove the obstruction

(problem): Insufficient amount of water pumped (cause):

1. Dirty tube filter
2. Water level quickly going down

3. Maximum head of delivery exceeded

4. Transport guide broken

(measures):

1. Clean the tube filter
2. Ensure sufficient inflow
3. Check the transport path length
4. Check the transport guide

(problem): Thermal detector switching the pump off

(cause):

1. Dirty tube filter
2. Water temperature too high
3. Pump running continuously at maximum pressure.

(measures):

1. Clean the tube filter and let the pump cool down
2. Reduce the water temperature
3. Make more breaks

Inspections and maintenance

Except for the below-described cases, the pump must be delivered to the customer service department for any repairs. Sand and other abrasive solids cause premature wear and pump power reduction. Works on the pump electric equipment can explicitly be executed by the customer service department only (that also applies for the electric cable and float). The drowned sludge pumps are virtually maintenance-free. Oilless bearings. Occasional filter support cleaning is enough, no other maintenance is necessary. Original spare parts must only be used in any case.

To ensure long service life of the pump seal, we recommend rinsing the pump with clean water in regular intervals.

Safety instructions for inspections and maintenance

It is always necessary to interrupt feeding (plug pulled out of socket) and make sure the pump is not going to start before any pump maintenance. Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries.

Inspection and maintenance plan

Time interval Description Any other		details
As needed Cleaning and rinsing out

Service

Any technical questions? Complaint? Do you need spare parts or operation manual?

Go to our website www.guide.com and the section Service will help you quickly and without bureaucracy. Please, help us to help you. In order to identify your device in case of complaint, please indicate serial number, order number and year of manufacture. All information is available on the product label. To have all information always at hand, put them down.

Serial number:

Order number:

Year of manufacture:

Phone: [phone] / 700-360

Fax: [phone]

E-Mail: [e-mail]

Important information for the customer

Please be sure to know that returning the product in or after the warranty period must be made in the original packaging.

Manuale step by step

(npo6nem): MoTope He ce 3aBnxBa

(Причизна):

1. JuncBa HanpeXeHne Ha MpeXaTa
   2.Блokирано колно Ha nomnata
2. BkIIOUbATEJIHa nannabBaKbI NOJIOXeHHe Ha N3KIIOYBaHe

(B3eTa Mpa):

(npo6nem): Nomnata He 3acMykBa

(нрчина):

1. Tomma 6e3 Boda
2. IpekaJeHo HnCKO HnBO Ha BoDaTa
3. 3aDpbcTeHO KOJEno Ha NOMnata

(B3eTa MЯрka):

1. OctaBeTe da ce oCBO6oJrBb3dyuHnTe Mexypn (kapr.D)
   2.ИЗКИЧЕТЕnomnata，HNBOTHa BOДаТТРбВдаCE nobuIN.
2. OTePahHe 3aDpbCTBaHETO

(npo6nem): HeoctaTbUHO KOINueCTBO

( npnnuHa): n3nomBaHa Boda

1. 3ambpceh 3acMykBaU KOU
   2.HIBOTO HA BOJATA 6bp30 cna
2. MakcImaHata TpaHCnOpTHa BNCOuHa e PpeMHATA
   4.ПуechунbaheВТрансортнataHHTaJIaUN

(B3eTa MЯрka):

1. NocTeTe 3acMyKBaUNa KOU
   2.OcnrypeTe DocTaBueH npITOK
2. Поверете дьлхината на Траснортото Трace
   4.Поверете TrpaHcnpTHaTaNCTaJIaUNI

(npo6nem): TonHHHna DaTcHKN3KIOUba nomnata

(нрчина):

1. 3ambpcen 3acMykBaau Koo
   2.Ппекално Висока TempepaTypa Ha BOДАТа
2. Tomnata pa60Tu nocToHHo npu MaKcMaJIHO HaIraHe.

(B3eTa Mrykka):

1. TOnHCTeTe 3aCMyKBaUNa K0U N OCTaBeTe NOMnTa Da N3CTVHe.
   2.Поннжerte temnepaypataHa BOdaTa
2. PpaBeTe No-ecTo npay3n

IperJeun noDpBxka

Cn3KIOUeHHe HaOny OnNCaHIne Cnyau nOMnTa Tp8Ba Bcnyau Ha pEmoHT da ce 3nPaTn B KIneHTCKn cepBN3.
PncbN ndpyrn a6pa3nBnB BeueCTBa npuHHBaT
npexDeBPemHeHO H3NOCBaHe N NOHNKeHe HA MoUHocTTA
Ha nOmNaTAp. PabOta H enEeKTPnuCeTKO yCTpoINCTBO Ha
nomnata MOKe Da n3BbPwBA M3KnIOuTHeNo CAMO KIneHTCKn
cepBN3 (TOBa BaXn I 3a enEeKTPnuCeKN Ka6en I nonnaBka).
NotanruiTe NOMn 3a yTaKn npakTNueckn ca 6ez
noDpBXKa. NaepRte Ce cMaBt Camn. OoctaTuHo e
nePiOnuHNO noocTbaHe NaOkbIa H foNTbpa, dpyra
noDpBXKa He e Heo6XoDMa. Pa3peSeHoe E bB BCEk
cUYaJ da ce nON3BaTcAMn oprtnHaHn pe3epBNu acTHn.

3a da 6bde rapaTnpaH bIb r cpoK Ha XepMeTnHocTTHa NOMNaTa, npenOpBvBaMe B peoBHN HHTepBann OT BpeMe Da ce n3nJaKHe C YnCTa BOda.

Hnctpykun 3a 6e30anacnoct 3a npereNn noDpBxka

IpeiN3BbPbBaHe Ha KaKbATO n da 6nlo noDpBxka Ha NOMnata e Heo6XoIMBO BnHaHn Da ce NpeKbcHE 3axpaHbAeTO (da CE I3BaDN ciEcnBba NT iEENCeHNHATA KyTHa) n da CE y6BeNTe, Ye NOMnATA HMA Da CE BKIOUH. Camo peoBHO NoDlbPxkAn IOcbNyBbAH ypei MoKe da 6bJe 3aOBoNBAuO nomarano. HeoCTaTbUHa NoDpBxxKa I npKka Morat da DoBeMaT do HeoayKaBHn 3NONONYK IN HapaHbAHNA.

PnHaHn pnernei nnoDpBxka

Инт扼Вал оТ Врeme	Описанne	ЕbvENT. Другни детайни
Сторад hyждиTe	Да се почinctи и изллakнe

CepBn3

IMate INTexHnueckn Bbnpoc? Peknamaun? Heo6xOJIMn INBcpe3epBnH qacTn nn ynbTbaHe 3a o6cnyKbaHe? Ha HauInTe ctpanuNw.guede.com B otDen CepBn3 ue Bin NOMORHEM 6bp30 n 6e3 n3nnuHa 6hopokpaia. IOMORHete HN,MOJ, 3a da MoXem Da BN nomarame. 3a da MoXem Da NdeHTnФmUpame Baunr ypeB cCnyaH na peKnaumra, Hn e Heo6xOJIMNo Da 3haem HerOBnB cepenH Omep, Homepa Ha npOyKa T NODnHa N pOn43BOdCTBO.BCNKN Te3n daHHn Ue HamePte NaTNOBATA Ta6Ebn. 3a da n IMate No pBka NoctOAHHO, 3aNNuTe rN, MOJ, TYK.

CepneH HOMeP:

Homep Ha npodykta:

TOnHa Ha npOn3BOcTBo:

Ten.: +49 (0) 79 04 / 700-360

ΦaKc: +49 (0) 79 04 / 700-51999

E-Mail: [e-mail]

BaxHHnHΦopMaun3aKJIneHTa

PpeynpekdaBame,Ye BpshaHeTo No BpeMe Ha rapaHOnHnIcPOK nIIN cIeI rapaHOnHnIcPOK e Heo6XOnMo BNHaN Da ce I3bBpUIN B opRiHaJIHa ONaKOBKa. C TaI MpaKpe 1e Ce n36berHe N3JIMHOTO yBpeXdAHe NO BpeMe Ha TpaHCnpTIPane H erHOBOTo YcTeCtO CNOpHO ypeXdAe. YcTpoIcTBOTO e 3aUHTeHO ONTImaJIHO CAMO B opRiHaJIHaTa ONaKOBKa, IN Taka E OCHTypeHa PJIaBAHn npepaBoTka.

RO

Translation of the EC-Declaration of Conformity

We, hereby declare the conception and construction of the below mentioned appliances correspond - at the type of construction being launched - to appropriate basic safety and hygienic requirements of EC Directives.

In case of any change to the appliance not discussed with us the Declaration expires.

2006/95/EC 2004/108/EC

2009/105/EC 1907/2006/EC

2011/65/EC ROHS 2009/142/EC

89/686/EEC (PPE) 1935/2004/EC

2006/42/EC

Annex IV

Notified Body

0197

Name: TUV Rheinland LGA Products GmbH

Adress: Nystrasse 2

90431 Nurnberg Germany

Type Ex.Cert.-No.:

97/68/EC_

Emission No.:

2000/14/EC_2005/88/EC