KG 19001 - Other kitchen appliances ADE - Free user manual and instructions

USER MANUAL KG 19001 ADE

• English Scope of delivery Electric salt and pepper mill Battery type LR/R03 (AAA), 1.5 V (6x) Operating Manual Intended use This device is intended for private use and for the scope of use normally associated with it. The device is not recommended for commercial or household-like use in staff kitchens at shops, offices and other commercial areas, in agricultural estates, by customers in hotels, motels or other residential facilities, or in bed and breakfasts. General information p. 14
• Scope of delivery p. 15
• Safety p. 16
• Technical data p. 18
• Warranty p. 18
• Overview p. 19
• Inserting/changing batteries p. 20
• Filling the mill p. 21
• Use p. 22
• Cleaning p. 23
• Storing p. 23
• Fault/Remedy p. 24
• Declaration of Conformity p. 24
• Disposal Table of Contents16 Electric salt and pepper mill KG 1900-x Safety This product may be used by children aged8 and above, as well as by persons with reduced physical, sensory, or mental capacities or lacking experience and knowledge if they are supervised or have been instructed in the safe use of the product and understand the risks that may arise. Children must not play with the product. Cleaning and user maintenance must not be carried out by children, unless they are 8years of age or older and are being supervised. Batteries, when swallowed, can be life-threatening. You should therefore keep the item and batteries out of reach of children. If a battery has been swallowed, medical assistance must be sought immediately. DANGER for children Keep packaging material away from children. There is a risk of choking if swallowed. Also pay attention that children do not pull the packaging material over their heads.Electric salt and pepper mill KG 1900-x p. 24

English RISK of fire/burning and/or explosion There is a risk of explosion if the battery is replaced improperly. Replace the batteries only with those of the same or an equivalent type. Pay attention to the “Technical data”. Batteries must not be recharged, reactivated by other means, dismantled, thrown into re, or short-circuited. Otherwise, there is an increased risk of explosion and leakage; furthermore, gases may escape! Avoid contact of the battery uid with skin, eyes, and mucosa. In case of contact, immediately rinse the aected areas with plenty of clean water and consult a doctor. BEWARE of material damage The mill or its parts must not be immersed in water or other liquids. This will damage the article. Remove the batteries from the mill if they are empty or if the mill will not be used for an extended period of time. You will thus avoid damage that may result from leakage of battery acid. Do not expose the batteries to any extreme conditions, e.g. by storing them on heaters or under direct sunlight. Increased risk of leakage! Ensure the batteries are inserted with the correct polarity (+/-) to avoid damaging the device. Risk of explosion! Clean the battery and device contacts, as needed, before inserting the battery. Risk of explosion! Always replace all of the batteries at the same time. Do not mix battery types, brands or batteries with dierent capacities. Risk of explosion!18 Electric salt and pepper mill KG 1900-x The grinding chamber should be a maximum of 80% full. Dampness may cause salt crystals to expand, which might cause the chamber to burst. Only turn on the mill when it is lled (with salt or pepper). Otherwise, the grinding gears might get damaged. Do not make any modications to the device. Only allow repairs to be carried out at a specialist workshop and pay attention to the guarantee conditions. Unprofessional repairs can damage the device. Do not clean the mill with hard, rough or abrasive cleaning agents. Otherwise, the surface could be scratched. Technical data Model: Electric salt and pepper mill KG 1900-1 (mint) KG 1900-2 (red) KG 1900-3 (black) Batteries: 6x LR/R03 (AAA) / 1.5 V Rated current: 900 mA Dimensions: ø 57 x 205 mm Distributor: Waagen-Schmitt GmbH Neuer Höltigbaum 15 22143 Hamburg, Germany Our products are constantly being developed and improved. For this reason, design and technical modifications are possible at any time. Warranty Dear Customer, Waagen-Schmitt GmbH warrants for 2 years from the purchase date the cost- free rectification of defects in material and workmanship through repair or exchange. In the event of a warranty claim, please return the product with the proof of purchase (specifying the reason for claim) to your dealer.Electric salt and pepper mill KG 1900-x

English 1 On/off switch 2 Case cap 3 Engine block and battery compartment (under case cap) 4 Grinding rod 5 Light guide 6 Grinding chamber for salt or pepper 7 Protective cap 6 Setting knob for coarseness 9 Light

Electric salt and pepper mill KG 1900-x Inserting/changing batteries Six type LR/R03 1.5 V batteries are required to use the device (these are included).

1. Firmly hold the bottom of the mill.

2. Turn the case cap anti-clockwise as far as it will

go with the other hand. Note the position of the open lock symbol.

3. Pull the cap upwards.

4. Remove the old batteries. Note the information

about disposal of batteries.

5. Insert six batteries (see “Technical data” for the

type) as shown in the diagram. Pay attention to the correct polarity (+/-).

6. Replace the case cap and turn it clockwise as far

as it will go. Note the position of the closed lock symbol.Electric salt and pepper mill KG 1900-x

English If the salt and pepper mill no longer works, the batteries must be changed. Always change all the batteries at once. Only use the type of battery that is specied in the “Technical data”. Dispose of old batteries in an environmentally appropriate way (see “Disposal”). Filling the mill

1. Firmly hold the bottom of the mill.

2. Turn the case cap anti-clockwise as far as it will

go with the other hand. Note the position of the open lock symbol.

3. Pull off the case cap by pulling up.

4. Pull off the engine block by pulling up.

5. Fill the grinding chamber a max. of 80% with

salt crystals or peppercorns.22 Electric salt and pepper mill KG 1900-x

6. Put the engine block back on the grinding

chamber. Make sure that the contact for the lighting is in the correct position.

7. Replace the case cap and turn it clockwise as far

as it will go. Note the position of the closed lock symbol. The mill is now locked and ready-to-use. Use WARNING - damage to property − Only turn on the mill when it is lled (with salt or pepper). The mill enables you to grind salt or pepper right when you need them. This means that the spices are more aromatic.

1. Remove the protective cap.

2. Hold the mill over the food you want to season

and press the on/off switch. The grinding gears and light will operate as long as the switch is held down.

3. After use, replace the protective cap.

If the mill jams, this means the grinding gears are blocked. If this happens, shake the mill a bit, turn it upside-down and turn it on briefly. Setting the coarseness

1. Remove the protective cap.

2. Turn the mill upside-down and turn it on briefly

to clear out the grinding gears.Electric salt and pepper mill KG 1900-x

3. Turn the setting knob in the middle of the

grinding gears in the corresponding direction. Pay attention to the marking on the setting knob. Coarse grind − Turn anti-clockwise Fine grind − Turn clockwise The grinding gears can be completely closed by turning the setting knob clockwise as far as it will go. In this case, do not press the on/off switch, because doing so will quickly destroy the grinding gears. Cleaning WARNING - damage to property − The mill or its parts must not be immersed in water or other liquids.

1. Wipe the mill with a soft, slightly damp cloth.

2. The grinding chamber can be cleaned with mild

dishwashing detergent in water. Dry thoroughly afterwards. Storing If the mill will not be used for a long period of time:

1. Remove the batteries.

2. Remove the contents from the grinding

chamber and clean it.

3. Store the mill in a dry, frost-free location.24

Electric salt and pepper mill KG 1900-x Fault/Remedy Fault Possible cause No function Are the batteries empty or inserted the wrong way around? Mill is working, but nothing is coming out. Did you remove the protective cap? Have you accidentally turned the setting knob for coarseness as far as it will go? If the light stops working, it is not possible to repair or replace it. Declaration of Conformity Waagen-Schmitt GmbH hereby declares that the KG 1900-1, KG 1900-2, and KG 1900-3 electric salt and pepper mills conform with 2014/30/EU and 2011/65/EU standards. This declaration loses its validity if any modification is made to the item that has not been agreed with us in advance. Hamburg, March 2021 Waagen-Schmitt GmbH Disposal Dispose of the product in accordance with the regulations that apply in your country. You will find complete information about disposal in the full operating manual. Disposing of the packaging Dispose of the packaging with similar materials. Dispose of cardboard with waste paper and of films with recyclable materials.Electric salt and pepper mill KG 1900-x