PABS 20Li F7 - Drill PARKSIDE - Free user manual and instructions

USER MANUAL PABS 20Li F7 PARKSIDE

Translation of the original instructions

SET 20V PABS 20-Li F7 Introduction Congratulations on the purchase of your new appliance. You have chosen a high-quality product. The operating instructions are part of this product. They contain important information about safety, usage and disposal. Before using the product, please familiarise yourself with all of the operating and safety instructions. Use the product only as de- scribed and for the range of applications specified. Please also pass these operating instructions on to any future owner. Intended use This appliance is designed for screwing and drilling into wood, plastic and metal. The appliance may only be used as described and for the specified application areas. Any other usage of or modifica- tion to the appliance is deemed to be improper and carries a significant risk of accidents. The manufacturer accepts no responsibility for damage caused by incorrect use of the appliance. This appliance is not intended for commercial use. Features 1 Speed selector switch 2 Bit holder (magnetic) 3 Rotation direction switch/lock 4 ON/OFF switch/speed control 5 Belt clip 6 Battery charge level button 7 Battery display LED

Battery pack (2x) 9 Battery pack release button 0 LED work light q Chuck w Torque preselection ring e High-speed charger r Red charge control LED t Green charge control LED z Replacement lead for pencil u Cutter knife i Tape measure o Centre punch p Countersink 20a Socket wrench set a 75 mm bits s 50 mm bits d Metal drill set f Bit holder g 25 mm bits h Wood drill set j Carpenter’s pencil Package contents 1 cordless drill driver 20V 1 high-speed battery charger 2 battery packs 1 bit holder 20 bits (25 mm) 10 bits (50 mm) 10 bits (75 mm) 1 cutter knife 1 carpenter’s pencil incl. 2 spare leads 1 tape measure (5 m) 8 socket wrench set 1 countersink 1 centre punch Set of 5 wood drills Set of 14 metal drills 1 carrying case 1 set of operating instructionsPABS 20-Li F7

3 ■ Technical data Cordless Drill Driver 20V PABS 20-Li F7 Rated voltage 20 V (DC) Rated idle speed 1st gear n

0–400 rpm 2nd gear n

0–1400 rpm Chuck clamping range max. Ø 13 mm Max. drill diameter Steel 13 mm Wood 30 mm Battery PAP 20 B1 Type LITHIUM ION Rated voltage 20 V (DC) Capacity 2 Ah Cells 5 High-speed battery charger PLG 20 C1 INPUT Rated voltage 230–240 V ∼, 50 Hz (AC) Rated power consumption 65 W Fuse (internal) 3.15 A T3.15A OUTPUT Rated voltage 21.5 V (DC) Rated current 2.4 A Charging time approx. 60min. Protection class II / (double insulation) Noise emission value Noise measurement value determined in accord- ance with EN 62841. The A-rated noise level of the power tool is typically: Sound pressure level L

= 68.4 dB (A) Uncertainty K K

= 5 dB Sound power level L

= 79.4 dB (A) Uncertainty K K

= 5 dB Vibration emission value Total vibration values (vector total of three direc- tions) determined in accordance with EN 62841: Screwdriving Vibration emission value

NOTE ► The vibration emission values and the noise emission values specified in these instructions have been measured in accordance with a standardised test procedure and can be used for comparing the power tool with another power tool ► The specified total vibration values and the noise emission values can also be used to make a provisional estimate of the load. WARNING! ► Depending on the manner in which the power tool is being used, and in particular the kind of workpiece being worked, the vibration and noise emission values can deviate from the values specified in these instructions during actual use of the power tool. ► Try to keep the vibration load as low as possible. Measures to reduce the vibration load are, e.g. wearing gloves and limiting the working time. Wherein all states of operation must be included (e.g. times when the power tool is switched off and times where the power tool is switched on but running without load).PABS 20-Li F7 ■ 4 

General power tool safety warnings WARNING! ► Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmos- pheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of elec- tric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating a power tool may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection.Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate condi- tions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.PABS 20-Li F7

5 ■ g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. h) Do not allow yourself to get lulled into a false sense of security and do not ignore the safety rules for power tools, even if you are familiar with the power tool after repeated use. A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that can- not be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or remove the battery pack, if detacha- ble, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool acci- dentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edg- es are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits, etc., in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Use and handling of the cordless

electrical power tool a) Charge a rechargeable battery using only the charger recommended by the manu- facturer. Chargers are often designed for a particular type of rechargeable battery unit. There is the danger of fire if other types of rechargeable battery units are used. b) Only the rechargeable battery units supplied are to be used with an electrical power tool. The use of other rechargeable battery units may lead to the danger of injury or fire. c) When they are not being used, store re- chargeable battery units away from paper- clips, coins, keys, nails, screws or other small metal objects that could cause the contacts to be bridged. Short-circuiting the contacts of a rechargeable battery unit may result in heat damage or fire. d) Fluids may leak out of rechargeable battery units if they are misused. If this happens, avoid contact with the fluid. If contact occurs, flush the affected area with water. Seek addi- tional medical help if any of the fluid gets into your eyes. Escaping battery fluid may cause skin irritation or burns. e) Do not use damaged or modified batteries. Damaged or modified batteries may behave unexpectedly and cause fires, explosions or pose a risk of injury.PABS 20-Li F7 ■ 6 

f) Do not expose a battery to fire or excessively high temperatures. Fire or temperatures in excess of 130°C (265°F) can cause an ex- plosion. g) Follow all instructions regarding charging and never charge the battery or the cordless tool outside of the temperature range given in the operating instructions. Incorrect charging or charging outside of the permissible tempera- ture range can destroy the battery and increase the risk of fire. CAUTION! RISK OF EXPLOSION! Never charge non-rechargeable batteries. Protect the rechargeable battery from heat (for example, from continuous exposure to sunlight), fire, water and moisture. There is a risk of explosion.

a) Have your power tool serviced by a qualified repair person using only identical replace- ment parts. This will ensure that the safety of the power tool is maintained. b) Never try to repair damaged batteries. Battery maintenance should only be carried out by the manufacturer or an approved customer service centre. Safety instructions for drills Safety instructions for all work ■ Hold the appliance by the insulated gripping surfaces when carrying out work during which the screws or the accessory tool may hit concealed power lines. If the accessory tool or the screws come into contact with a live wire, this may make exposed metal parts of the power tool live and result in an electric shock. ■ Collect any dust that is produced; for example, using a vacuum cleaner. Safety instructions when using long drill bits ■ Do not use a higher speed than the maximum permissible speed for the drill bit. At higher speeds, the drill bit can easily bend if it is al- lowed to rotate freely without being in contact with the workpiece, which may lead to injuries. ■ Always start drilling at a low speed and with the drill bit in contact with the workpiece. At higher speeds, the drill bit can easily bend if it is allowed to rotate freely without being in contact with the workpiece and this can lead to injuries. ■ Do not exert excessive pressure, and only apply pressure along the length of the drill bit (no lateral pressure). Drill bits can bend and and break which can lead to a loss of control and injuries. Original accessories/attachments ■ Use only the accessories and attachments which are specified in the operating instructions and are compatible with the appliance. WARNING! ■ Do not use any accessories which have not been recommended by PARKSIDE. This can lead to electric shock and fire.PABS 20-Li F7

7 ■ Safety guidelines for battery chargers ■ This appliance may be used by children aged 8 years and above and by persons with limited physical, sensory or mental capabilities or lack of experience and knowledge, provided that they are under su- pervision or have been told how to use the appliance safely and are aware of the potential risks. Do not allow children to use the appliance as a plaything. Cleaning and user maintenance tasks may not be car- ried out by children unless they are supervised. ■ To avoid potential risks, if the mains cable of this appliance is damaged, it must be replaced by the manufac- turer, or its customer service depart- ment or a similarly qualified person. The charger is suitable for indoor use only. ATTENTION! ♦ This charger can only charge the following batteries: PAP20A1/PAP20A2/ PAP20A3/PAP20B1/PAP20B3. ♦ An up-to-date battery compatibility list can be found at www.Lidl.de/Akku. Before use Charging the battery pack (see fig. A) CAUTION! ► Always disconnect the mains plug before removing the battery pack 8 from or insert- ing it into the charger. NOTE ► Never charge the battery pack at an ambient temperature of below 10°C or above 40°C. If a lithium-ion battery is to be stored for an extended period, the charge level must be checked regularly. The optimum charge level is between 50% and 80%. The storage climate should be cool and dry and the ambient tem- perature should be between 0°C and 50°C. ♦ Insert the battery pack 8 into the high-speed charger e (see fig. A). ♦ Insert the power plug into the socket. The green charge control LEDt lights up briefly, then the red charge control LED r lights up. ♦ The green control LED t indicates that charging is complete and the battery pack 8 is ready for use. ♦ Insert the battery pack 8 into the appliance (see fig. B). Inserting/removing the battery pack Inserting the battery pack: ♦ Set the rotation direction switch 3 to the middle position (lock, see fig. C). Slide the battery pack 8 into the handle until it engages (see fig. B). Removing the battery pack: ♦ Press the release button 9 and remove the battery pack 8 (see fig. D).PABS 20-Li F7 ■ 8 

Checking the battery charge level ♦ To check the battery status, press the battery charge level button 6 (see fig. E). The status/ remaining charge is shown on the battery display LED 7 as follows: GREEN/RED/ORANGE = maximum charge/ performance RED/ORANGE = medium charge/performance RED = low charge – charge the battery Changing tools Your cordless screwdriver has a fully automatic spindle lock . When the motor is at a standstill, the drive train is locked so that you can open the drill chuck q by turning it . After you have inserted the desired tool and clamped it by turning the drill chuck , you can resume working immediately (see fig. F). The spindle lock is released automatically when the motor is started (by pressing the ON/OFF switch 4). Torque selection ring/drill setting You can set the torque using the torque pre- selection ring w (see fig. G). ♦ Select a low level for small screws or soft materials. ♦ Select a high level for large screws, hard materials or for removing screws. ♦ For drilling operations, select the drill setting by moving the torque preselection ring w to the position. 2-speed gearbox CAUTION! ► Operate the speed selector switch 1 only when the appliance is at a standstill. Other- wise the appliance could be damaged. In first gear (speed selector switch 1 in position 1) you can reach a speed of approx. 400 rpm and ahigh torque. This setting is suitable for all screw driving jobs. In second gear (speed selector switch 1 in position 2) you can reach a speed of approx. 1400 rpm for carrying out drilling work. Changing the cutter knife blade WARNING! ■ Wear protective gloves! ♦ Press the red button on the rear end of the cutter knife to pull out the spare blade holder completely. ♦ Carefully remove the worn upper blade. ♦ Slide the spare blade holder back into the housing. Detaching the blunt cutter knife blade ♦ Break the blunt section of the blade off at the defined breaking point using a pair of pliers. Use Switching on/off Switching on ♦ Press and hold the ON/OFF switch 4 to start up the appliance. The LED work light 0 lights up when the ON/ OFF switch 4 is pressed slightly or fully, and illuminates the working area in low light conditions. Switching off ♦ Release the ON/OFF switch 4 to switch off the appliance.PABS 20-Li F7

9 ■ Setting the rotational speed The ON/OFF switch 4 has a variable speed con- trol. Pressing the ON/OFF switch 4 yields a low speed. Increasing the pressure increases the speed. NOTE ► The integrated motor brake ensures that the appliance stops quickly. Changing the direction of rotation ♦ Change the direction of rotation by pushing the rotation direction switch 3 to the right or left. Tips and tricks Tip! How to do things correctly. ♦ Before operation, check whether the screw or drill insert is correctly fitted, i.e. centred in the drill chuck. ♦ Screw bits are labelled according to their di- mensions and their shape. If you are uncertain, always check first whether the bit fits tightly in the screw head without any play. Torque ♦ Smaller screws/bits can be damaged if you set too high a torque or too high a speed. Hard screw joints (in metal) ♦ Particularly high torques occur, e.g. in metal screw joints made using socket wrench bits. Select a low rotational speed. Soft screw joints (e.g. in soft wood) ♦ Here, too, use a low speed to avoid damaging the wood surface when it comes into contact with the metal screw head. Use a countersink. When drilling in wood, metal and other materials, observe the following ♦ Use a high speed for drill bits with a small diameter and a low speed for drill bits with a large diameter. ♦ Select a low speed for hard materials and a high speed for soft materials. ♦ Secure or fasten the workpiece in a clamp or vice (if possible). ♦ Mark the spot where you want to drill with a punch or nail. Select a low rotational speed when you start drilling. ♦ Pull the rotating drill bit out of the hole several times to remove dust and chips and clear the hole. Drilling in metal ♦ Use a metal drill (HSS). For optimum results, cool the drill bit with cutting oil. Metal drill bits can also be used to drill into plastics. Pre-drill with a 3 mm diameter drill bit and then increase the size until the desired hole diameter is achieved. Drilling in wood ♦ Use a wood drill with a centring point: for deep drilling use an auger bit and for large drill diameters use a Forstner bit. Small screws can be screwed directly into soft wood without pre-drilling.PABS 20-Li F7 ■ 10 

Maintenance and cleaning WARNING! RISK OF INJURY! Always switch the appliance off and remove the battery before carrying out any work on the appliance. The cordless screwdriver is maintenance-free. ■ The appliance must always be kept clean, dry and free from oil or grease. ■ Never allow liquids to get into the appliance. ■ Use a dry cloth to clean the housing. Never use petrol, solvents or cleansers which can damage plastic. ■ If a lithium-ion battery is to be stored for an extended period, the charge level must be checked regularly. The optimum charge level is between 50% and 80%. The optimum storage environment is cool and dry. NOTE ► Replacement parts that are not listed (such as batteries, switches) can be ordered via our Service Hotline. Kompernass Handels GmbH warranty Dear Customer, This appliance has a 3-year warranty valid from the date of purchase. If this product has any faults, you, the buyer, have certain statutory rights. Your statutory rights are not restricted in any way by the warranty described below. Warranty conditions The warranty period starts on the date of purchase. Please keep your receipt in a safe place. This will be required as proof of purchase. If any material or manufacturing fault occurs within three years of the date of purchase of the product, we will either repair or replace the product for you or refund the purchase price (at our discretion). This warranty service requires that you present the defective appliance and the proof of purchase (re- ceipt) within the three-year warranty period, along with a brief written description of the fault and of when it occurred. If the defect is covered by the warranty, your prod- uct will either be repaired or replaced by us. The repair or replacement of a product does not signify the beginning of a new warranty period. X 12 V and X 20 V Team Series battery packs come with a 3-year warranty valid from the date of purchase.PABS 20-Li F7

11 ■ Warranty period and statutory claims for defects The warranty period is not prolonged by repairs effected under the warranty. This also applies to replaced and repaired components. Any damage and defects present at the time of purchase must be reported immediately after unpacking. Repairs carried out after expiry of the warranty period shall be subject to a fee. Scope of the warranty This appliance has been manufactured in accord- ance with strict quality guidelines and inspected meticulously prior to delivery. The warranty covers material faults or production faults. The warranty does not extend to product parts subject to normal wear and tear or to fragile parts which could be considered as consumable parts such as switches or parts made of glass. The warranty does not apply if the product has been damaged, improperly used or improper- ly maintained. The directions in the operating instructions for the product regarding proper use of the product are to be strictly followed. Uses and actions that are discouraged in the operating instructions or which are warned against must be avoided. This product is intended solely for private use and not for commercial purposes. The warranty shall be deemed void in cases of misuse or improper handling, use of force and modifications / repairs which have not been carried out by one of our authorised Service centres. The warranty period does not apply to ■ Normal reduction of the battery capacity over time ■ Commercial use of the product ■ Damage to or alteration of the product by the customer ■ Non-compliance with safety and maintenance instructions, operating errors ■ Damage caused by natural hazards Warranty claim procedure To ensure quick processing of your case, please observe the following instructions: ■ Please have the till receipt and the item number (IAN)374072_2104 available as proof of purchase. ■ You will find the item number on the type plate on the product, an engraving on the product, on the front page of the operating instructions (below left) or on the sticker on the rear or bottom of the product. ■ If functional or other defects occur, please contact the service department listed either by telephone or by e-mail. ■ You can return a defective product to us free of charge to the service address that will be pro- vided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred. You can download these instructions along with many other manuals, product videos and installation software at www.lidl-service.com. This QR code will take you directly to the Lidl service page (www.lidl-service.com) where you can open your operating instructions by entering the item number (IAN) 374072_2104.PABS 20-Li F7 ■ 12 

WARNING! ► Have your appliances repaired by the service centre or a qualified electrician and only using genuine replacement parts. This will ensure that the safety of the appliance is maintained. ► Always ensure that the power plug or the mains cable is replaced only by the man- ufacturer of the appliance or its customer service department. This will ensure that the safety of the appliance is maintained. Service Service Great Britain Tel.: [phone] E-Mail: [e-mail] Service Ireland Tel.: [phone] (0,08 EUR/Min., (peak)) (0,06 EUR/Min., (off peak)) E-Mail: [e-mail] IAN 374072_2104 Importer Please note that the following address is not the service address. Please use the service address provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com Disposal The packaging is made from environ- mentally friendly material which can be disposed of at your local recycling plant. Do not dispose of power tools in the normal domestic waste! European Directive 2012/19/EU requires that worn-out power tools be collected separately and recycled in an environmentally compatible manner. Do not dispose of batteries in your normal household waste! Remove the batteries from the tool before disposal. Defective or worn-out rechargeable batteries must be recy- cled according to Directive 2006/66/EC. Take the battery pack and/or tool to a nearby collection facility. Please contact your local authority or town council for information about disposal options for used power tools/battery packs. Dispose of the packaging in an environ- mentally friendly manner. Note the labelling on the packaging and sepa- rate the packaging material compo- nents for disposal if necessary. The packaging material is labelled with abbreviations (a) and numbers (b) with the following meanings: 1–7: plastics, 20–22: paper and cardboard, 80–98: composites. Your local community or municipal authorities can provide information on how to dispose of the worn-out product. The product is recyclable, subject to extended producer responsibility and is collected separately.PABS 20-Li F7

13 ■ Original declaration of conformity We, KOMPERNASS HANDELS GMBH, document officer: Mr Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards, normative documents and EC directives: Machinery Directive (2006/42/EC) EC Low Voltage Directive (2014/35/EU, charger only) EMC (Electromagnetic Compatibility) (2014/30/EU) RoHS Directive (2011/65/EU)*

• The manufacturer bears the full responsibility for compliance with this conformity declaration. The subject of the declaration described above meets the requirements of Directive 2011/65/EU of the European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic tools. Related harmonised standards EN 62841-1:2015 EN 62841-2-1:2018/A11:2019 EN 60335-1:2012/A2:2019 EN 60335-2-29:2004/A11:2018 EN 62233:2008 EN 55014-1:2006/A2:2011 EN 55014-1:2017/A11:2020 EN 55014-2:1997/A2:2008 EN 55014-2:2015 EN 61000-3-2:2014 EN 61000-3-2:2019 EN 61000-3-3:2013 EN 61000-3-3:2013/A1:2019 EN 50581:2012 Type/appliance designation: Cordless Drill Driver Set 20V PABS 20-Li F7 Year of manufacture: 07–2021 Serial number: IAN 374072_2104 Bochum, 02/08/2021 Semi Uguzlu - Quality Manager - We reserve the right to make technical changes in the sense of further product development.PABS 20-Li F7 ■ 14 

Ordering a replacement battery If you want to order a replacement battery for your appliance, you can do so easily via the Internet on www.kompernass.com or by telephone. Due to limited stocks, this item may sell out in a relatively short time. NOTE ► Online ordering of replacement parts is not possible in all countries. In this case, please contact the Service hotline. Telephone ordering Service Great Britain Tel.: [phone] Service Ireland Tel.: [phone] (0,08 EUR/Min., peak · 0,06 EUR/Min., off peak) To ensure fast processing of your order, have the article number of your appliance to hand (IAN374072_2104) in case of questions. The article number can be found on the type plate or the title page of these instructions.PABS 20-Li F7