Curl & Straight AS8606 - Curling iron REMINGTON - Free user manual and instructions

USER MANUAL Curl & Straight AS8606 REMINGTON

• During use, always ensure the inlet and outlet grilles are not blocked in any way as this will cause the unit to automatically stop. If this should occur, switch o and allow the unit to cool.

• Keep the power plug and cord away from heated surfaces.

• Do not leave the appliance unattended while plugged in.

• Do not place the appliance on any soft furnishings.

• Do not use attachments other than those we supply.

• Do not set the appliance down while still on.

• Do not twist or kink the cable, or wrap it round the appliance.

• Do not use the appliance if it is damaged or malfunctions.

• Check the cord regularly for any sign damage.

• This appliance is not intended for commercial or salon use. PARTS

7. 40 mm soft bristle brush

8. Firm paddle brush

9. Pre-styling nozzle

• Plug the product into the mains power supply.

• Select your attachment before you turn on the appliance. To t an attachment:

• Align the Usymbol on the attachment with the 9 mark on the body (g. A).

• Turn the ring on rotating attachments (30 mm tong and 40mm brush), or the attachment itself (paddle brush or pre-styling nozzle) until the Lsymbol is aligned with the 9 mark to secure (g. B). To remove an attachment

• Align the U symbol with the 9 mark and pull the attachment o the handle. Temperature settings

• There are three temperature settings on the styler High, Low and Cool (for setting the style).

• To turn the appliance on slide the temperature control switch to I for low heat, II for high heat or f for the cool setting.

• Select the appropriate temperature for your hair type: ENGLISH

AE6 Temperature Hair Type Low Thin/ne, damaged or bleached hair High Thick and dicult to style hair Rotation settings

• Only the 30 mm tong and the 40 mm brush rotate.

• To use the rotating function press the right arrow (+) on the rotation switch to rotate the attachments clockwise and the left arrow (-) to rotate the attachments anti clockwise.

• NOTE: The brush and tong attachments will only start rotating when a temperature setting has been selected. Prepare the hair for styling

• Wash and condition the hair as normal.

• Squeeze out excess moisture with a towel and comb through.

• Using the pre-styling nozzle rough dry the length and roots until 80% dry.

• Divide the hair into sections, style the lower layers rst. Create volume and shape using the 40mm rotating brush

• To dry your roots and add volume, place the brush underneath the section close to the roots and hold for a few seconds, lifting the hair as you dry.

• Move the styler downwards through the hair section, at the same time rotate the brush away from the head by pressing and holding -or + as required.

• Keep moving the styler downwards to resist the brush rotation. Doing this will create tension through the section of hair.

• If the brush spins too quickly release the rotation switch and remove the brush from your hair.

• To create shape, continue rotating the brush until you reach the ends of the hair and then roll the ends under.

• For even more volume, wrap the bottom of the hair section around the brush. Press and hold the applicable rotation switch (- +) and wind the entire length of the section around the barrel, stopping at the roots. Release the rotation switch and hold the brush in the hair for a few seconds or until the section is dry.

• Repeat this around the head.

• Let the hair cool before styling.

• Let the attachment cool before removing.

• Place the protective cover over the brush head to protect the bristles from damage in storage. Create loose curls with the 30 mm rotating tong

• Place the end of a section of hair underneath the tong clip.

• Press and hold the applicable rotation switch (- +) and wind the entire length of the section around the barrel, stopping at the roots. ENGLISH7

• Release the rotation switch and hold the tong in your hair for 10 seconds or until the section is dry.

• Unwind the tong and release the curl.

• Repeat this around the head.

• Let the hair cool before styling.

• Let the attachment cool before removing. Create smooth, sleek hair using the rm paddle brush

• Starting at the roots, slowly brush through each section just as you would with a normal brush.

• To add additional volume tip your head upside down and brush the underneath of your hair.

• When dry use your ngers to shape the hair and ends.

• Let the attachment cool before removing Cool setting

• To set your style whilst using any of the attachments, use the cool setting. To operate slide the temperature control switch to the f position.

STORAGE, CLEANING AND MAINTENANCE

• After use, turn the appliance o by moving the temperature control switch to the O position.

• Unplug the appliance and allow to cool before cleaning and storing away.

• Wipe all surfaces with a damp cloth

• Don’t use harsh or abrasive cleaning agents or solvents,

• To maintain peak product performance and to prolong motor life, it is important to regularly remove any dust and dirt from the air lter grille and clean with a soft brush.

• Remove the grille as shown (g. C), clean with a cloth or soft brush, then replace it. RECYCLING

To avoid environmental and health problems due to hazardous substances, appliances and rechargeable and non-rechargeable batteries marked with one of these symbols must not be disposed of with unsorted municipal waste. Always dispose of electrical and electronic products and, where applicable, rechargeable and non-rechargeable batteries, at an appropriate ocial recycling/ collection point. ENGLISH

• Let the attachment cool before removing Koele instelling

9. Ugello pre-styling

• To maintain peak product performance and to prolong motor life, it is important to regularly remove any dust and dirt from the air lter grille and clean with a soft brush.