AS 3946 - Electric slicer SEVERIN - Free user manual and instructions

USER MANUAL AS 3946 SEVERIN

Before using the appliance, please read the following instructions carefully and keep this manual for future reference. The appliance must only be used by persons familiar with these instructions.

Familiarisation

1. Rating label (on underside of the unit)
2. Push switch
3. Release button
4. Slide lock for base plate
5. Power cord
6. Stainless steel blade
7. Blade mounting
8. Base plate (foldable)
9. End-piece holder with finger guard
10. Sliding tray
11. Stop plate
12. Thickness selection knob
13. Collection tray

Connection to the mains supply

Make sure that the supply voltage corresponds with the voltage marked on the rating label. This product complies with all binding CE labelling directives.

Important safety instructions

In order to avoid hazards, repairs to this electrical appliance or its power cord must be carried out by our customer service. If repairs are needed, please send the appliance to our customer service department

(see appendix).

• Before cleaning the appliance, ensure it is disconnected from the power supply and has cooled down completely.
• To avoid the risk of electric shock, do not clean the appliance with water and do not immerse it in water.
  The appliance must be cleaned regularly. For more detailed information, please refer to the section Cleaning and care.
• We strongly recommend that the appliance is only used with the sliding tray and end-piece holder properly installed and in position. Exceptions may be made only if required by the size or shape of the food to be sliced.
• Caution: Any misuse can cause severe personal injury.

• Caution: The blade is very sharp; extreme care should be taken when handling it.
  Always remove the plug from the wall socket

• when there is no supervision,

• before removing, replacing or

adjusting any part

• after use,
  -in case of any malfunction,
• during cleaning of the appliance.

This appliance is intended for domestic or similar applications, such as

• in shops, offices and other similar working environments,
• in agricultural working environments,
• by customers in hotels, motels etc. and similar establishments,
• in bed-and breakfast type environments.

The appliance may only be used by persons with reduced physical, sensory or mental capabilities, or lacking experience and knowledge, if they have been given supervision or instruction concerning the use of the appliance and fully understand all dangers and safety precautions involved.

Children must not be permitted to operate the appliance.
The appliance and its power cord must be kept well away from

children.

Children must not be permitted to play with the appliance.
- Caution: Keep any packaging materials well away from children – these materials are a potential source of danger, e.g. of suffocation.
- Every time the appliance is used, the main body including the power cord as well as any attachment fitted should be checked thoroughly for any defects. Should the appliance, for instance, have been dropped onto a hard surface, or if excessive force has been used to pull the power cord, it must no longer be used: even invisible damage may have adverse effects on the operational safety of the appliance.
- Do not allow the slicer to come into contact with open fl ames or any hot surface such as hotplates.
- Do not operate the slicer if the sliding tray, stop plate or base plate have not been correctly fitted.
- For safety reasons, always bring the stop plate back to its rest (zero) position after use, so that it is fl ush with the blade.
- Do not allow the power cord to come into contact with the blade. When removing the plug from the wall socket, never pull on the power cord.
- No responsibility is accepted if damage results from improper use, or if these instructions are not complied with.

Before using the appliance for the first time

• Unpack the appliance completely and remove any protective foils etc.
• Before first use, the unit should be

cleaned with a damp cloth, as described in Cleaning and care.

Operation

Applications

The slicer is designed for use with bread, cold cuts, ham, cheese, cold roasts and other foodstuffs suitable for slicing.

Short-term operation

The appliance has been designed for shortterm operation only, i.e. the slicer should not be operated continuously for more than 10 minutes. Switch it off afterwards and allow the motor to cool down before switching on again.

Positioning the slicer

The slicer must be positioned on a flat, solid surface.

Locking the base plate

Fold the base plate into its horizontal operating position, and then lock it by pushing the slide lock as far as possible in the direction of the hinge. To unlock, slide the lock away from the hinge.

Fitting the sliding tray

Hold the sliding tray vertically next to the base plate in such a way that the guide rail on the tray is located underneath the base plate. Pull the tray sideways and upwards so that the rail slips into the guide track underneath the base plate, and then fold the tray 90^ upwards to lock it into the track. The tray will now be securely fitted in the base plate track.

Setting thickness

The thickness of the slices is infinitely adjustable by means of the selection knob. Always bring the stop plate back to its rest (zero) position after use.

Safety switch

To activate the motor, first press the release button, then the push switch, which will lock in the operating position.

As soon as the switch is pressed again, the motor will automatically stop.

Slicing

Following the above safety instructions, the slicer can now be operated.

• Adjust the desired thickness of the slices.
• Position the collection tray next to the unit.
  Use the right hand to place the food to be sliced on to the sliding tray and to press it against the stop plate.
• Fit the end piece holder, with the studded side facing the blade, on to the tray.
• Use the left hand to press the release button and, almost simultaneously, the push switch, and then move the sliding tray against the rotating blade. At the same time, press the end piece holder containing the food lightly against the blade.
  The end piece holder ensures the food will be held safely while slicing takes place.
  The cut slices are collected in the tray underneath the unit.
• For safety reasons, always bring the stop plate back to its rest (zero) position after use so that it is fl ush with the blade.

Practical hints

• When cutting a loaf of bread where the crust is thicker or harder on the top, it should be placed against the blade in such a way that the firm part of the crust faces the cutting edge.
• When cutting cheese, or when cutting very thin slices of other foods, use a slightly moist cloth to wipe the blade first. This will make the slicing process easier.
• When cutting ham, ensure that the fatty side is facing upwards.

Cleaning and care

General

Always remove the plug from the wall socket before detaching any accessories, and before cleaning the appliance.
After switching off, always wait until the blade has come to a complete standstill. Bring the stop plate back to its rest (zero) position, so that the blade does not protrude.
- To avoid the risk of electric shock, do not clean the appliance with water and do not immerse it in water.
- Do not use abrasives or harsh cleaning solutions for cleaning. If necessary, the housing may be wiped with a slightly damp, lint-free cloth. The end piece holder and the sliding tray can be cleaned using hot water and a mild detergent (do not put them in a dish-washer).

Detaching and cleaning the blade

The blade is extremely sharp - there is a risk of serious injury if proper care is not taken.

The stainless-steel blade can be cleaned with a slightly damp, lint-free cloth.

The area behind the blade should also be cleaned occasionally. To remove the blade, loosen the central fixxing screw by turning it 90^ in a clockwise direction.

After cleaning, re-attach the blade following the same steps in reverse order.

Detaching the stop plate

For thorough cleaning, the stop plate can be removed. Turn the selection knob anticlockwise until the stop plate can be pulled out sideways. When refi tting the stop plate, follow the same steps in reverse order.

Detaching the base plate

The base plate can be removed for cleaning To facilitate correct ftting, the base plate has guide studs on both sides. Once the plate is brought into a vertical position, the studs can be pulled out of their guide slots and the plate can be taken off sideways. The plate may be cleaned with hot water and a mild detergent. When refi tting the plate, follow the same steps in reverse order.

Disposal

Devices marked with this symbol must be disposed of separately from your household waste, as they contain valuable materials

which can be recycled. Proper disposal protects the environment and human health. Your local authority or retailer can provide information on the matter.

Guarantee

This product is guaranteed against defects in materials and workmanship for a period of two years from the date of purchase. Under this guarantee the manufacturer undertakes to repair or replace any parts

found to be defective, providing the product is returned to one of our authorised service centres. This guarantee is only valid if the appliance has been used in accordance with the instructions, and provided that it has not been modifi ed, repaired or interfered with by any unauthorised person, or damaged through misuse.

This guarantee naturally does not cover wear and tear, nor breakables such as glass and ceramic items, bulbs etc. This guarantee does not affect your statutory rights, nor any legal rights you may have as a consumer under applicable national legislation governing the purchase of goods. If the product fails to operate and needs to be returned, pack it carefully, enclosing your name and address and the reason for return. If within the guarantee period, please also provide the guarantee card and proof of purchase.

FR

Trancheuse

Chere cliente, Cher client,

Sunnex Century Catering Equipment

(Shenzhen) Ltd.

2/F., Block A, Dong He Industrial Building

Yue He Street, Sha Shen Road, Sha Tou Jiao

Shenzhen

Tel.: [phone] or 25550852

Fax: [phone] or 25357498

eMail: [e-mail]

Web: http://www.severinchina.com

Czech Republic

BVZ Commerce s.r.o.

Parkerova c.p. 618

CZ 25067 Klecany

Tel.: [phone]

Fax:[phone]

Danmark

F&H of Scandinavia A/S

Gl. Skivevej 70

DK-8800 Viborg

Tel.: [phone]

Fax: [phone]

F-67210 OBERNAI CEDEX

Tel.: [phone]

Fax:[phone]

eMail: [e-mail]

Web: http://www.severin.fr

Greece

BERSON

C. Sarafi dis Bros. S.A.

Agamemnonos 47

176 75 Kallithea, Athens

Tel.: [phone]

Philippines Business Center

Service Post of Thermi

570 01 Thessaloniki, Greece

Tel.: [phone]

Hong Kong

Pacific Coffee Company

7/F Hollywood Centre, 233 Hollywood Road,

Sheung Wan, Hong Kong

Tel.: [phone]

Fax: [phone]

eMail:presso@pacifi ccoff ee.com

India

Zansaar

1210, 2nd Floor

Fawar Manor, 100ft Road

Indiranagar, Bangalore 560 038

Tel.: [phone]

eMail: [e-mail]

Web: http://www.zansaar.com

Iran

IRAN-SEVERIN KISH CO. LTD.

No.668,7th.Floor

Bahar Tower

Ave. South Bahar

TEHRAN - IRAN

Tel.: [phone]

Fax: [phone]

[e-mail]

www.iranseverin.com

Iraq

AI JOUD Home Appliances Manufacturing

Co. Ltd

PIC: Eng. Ahmad Al-Sharabi

Al Joud Building Karadat Kharej

Baghdad - Iraq

Tel.: [phone]
[phone]
[phone]

Ireland

Bluestone Sales & Distribution Ltd

26 Oaktree Business Park

Trim Co Meath Ireland

Tel.: [phone]

Fax: [phone]

Web: www.bluestone.ie

Italia

via Dino Col 52r-54r-56,

I-16149 Genova

Green Number: 800224155

Tel.: [phone]

Fax: [phone]

e-mail: [e-mail]

Jordan

J.L.C.

P.O.Box 910330

Mecca Street, Jaber Complex Building No. 193

Amman 11191 Jordan

Tel: [phone]

Korea

Jung Shin Electronics co., Ltd.

501, Megaventuretower 77-9

Moonrae-Dong 3ga, Yongdeungpo-Gu

Seoul, Korea

Tel: [phone]~7

Fax: [phone]

Service Hotline: [phone]

Kuwait

Mohammed Abdulrahman Al Bahar

Al Bahar Building P.O.Box 148

Safat 13002 Kuwait

Tel: [phone]

Latvia

SERVO Ltd.

Mr. Janis Pivovarenoks

Tel: [phone]

Lebanon

Khoury Home

7th Floor, Cité Dora 3 Building, Dora

P.O.Box 70611

Antelias, Lebanon

Tel: [phone]

Fax:[phone]

eMail: [e-mail]

Internet: www.khouryhome.com

Luxembourg

Ser-Tec

GHALA 112, P.O. Box 996

Muscat Sultanate of Oman

Tel.: [phone]

Fax.: [phone]

Philippines

COLOMBO MERCHANT PHILIPPINES, INC.

Mezzanine 1, South Center Tower

2206 Venture Street, Madrigal Business Park

Alabang, Muntinlupa City

Tel.: [phone]

eMail: severinconsumercare@colombophils. com.ph

Polska

SERV-SERWIS SP.Z 0.0.

UL.WSCHODNIA4

46-070 CHMIELOWICE K/OPOLA

Tel: [phone]

Fax:[phone]

Serbia and Montenegro

tel: [phone]

tel: [phone]

fax: [phone]

Singapore

Beste (S) Pte. Ltd.

Tagore Building

6 Tagore Drive, #03-04

Singapore 787623

Tel.: [phone]

Fax: [phone]

eMail: [e-mail]

Slovenia

SEVTIS d.o.o.

Smartinska 130

1000 Ljubljana

Tel: [phone]

Fax: [phone]

Slowak Republic

PREMT,s.t.o.

Skladova 1

917 01 Trnava

Tel: [phone]

Fax: [phone]

eMail:[e-mail]

South Africa

AL.CD. Ashley (Pty) Ltd

ABSA on Grove

Grove Avenue

Claremont, Cape Town 7708

Tel.: [phone]

Fax: [phone]

eMail:[e-mail]

Web: www.alcdashley.co.za

Svenska

Rakspecialisten HS

Mollevangsgatan 34

214 20 Malmö

Tel.: [phone]

Fax:[phone]

eMail: [e-mail]

Switzerland

Joud Industries Domestic Appliances Co.

P.O.Box 199 or 219

Motorway entrance

Lattakia - Syria

Tel.: [phone]

[phone]

Fax:[phone]

Thailand

Verasu Ltd. part.

83/7 Wireless Rd., Lumpini,

Patumwan, Bangkok 10330

Tel.: [phone]

eMail: [e-mail]

United Arab Emirates

Juma al Majid Est

P.O.Box 156

Dubai U.A.E.

Tel.: [phone]

Fax:[phone]

eMail: [e-mail]

Web: www.al-majid.com

United Kingdom

Homespares Centres Limited

Firwood Industrial Estate

Thicketford Road

Bolton, BL2 3TR

Tel.: [phone]

Fax: [phone]

eMail: offi [e-mail]

Web: www.hscl.info

Vietnam

Brand Partner

W.22, D. Binh Thanh

180/38 Nguyen Huu Canh Street

Ho Chi Minh City. Vietnam

Tel.: [phone]

Fax:[phone]

eMail: [e-mail]

Stand: 08.2014