LB 37 - Humidifier BEURER - Free user manual and instructions

Technical Features	Ultrasonic humidifier, 3.5-liter tank capacity, adjustable humidity output, coverage area up to 40 mB2.
Usage	Ideal for bedrooms, offices, and living spaces, operates with tap water, desired humidity setting.
Maintenance and Repair	Regular cleaning of the tank and parts, filter replacement if necessary, monthly descaling recommended.
Safety	Automatic shut-off when the tank is empty, stable design to prevent tipping over.
General Information	Quiet operation, modern design, water level indicator, low energy consumption.

Frequently Asked Questions - LB 37 BEURER

How do I fill the water tank of the BEURER LB 37 humidifier?

To fill the tank, remove it from the device, open the cap, and pour clean water up to the maximum level mark. Replace the tank once filled.

What type of water should I use in the humidifier?

It is recommended to use distilled or demineralized water to avoid limescale buildup and prolong the device's lifespan.

The BEURER LB 37 humidifier makes noise. Is this normal?

A slight operating noise is normal. However, if the noise is excessive, check that the device is on a flat surface and that the tank is properly installed.

Why is the humidifier not working?

Make sure the device is plugged in, the water tank is filled and properly installed, and the device settings are correct.

How do I clean the BEURER LB 37 humidifier?

Unplug it, empty the tank, and use a soft cloth with warm water and a little vinegar to clean the internal surfaces. Avoid abrasive products.

What is the noise level of the humidifier during operation?

The BEURER LB 37 humidifier is designed to be quiet, with a noise level of about 35 dB, making it suitable for bedrooms.

Can the humidifier be used continuously all night?

Yes, the BEURER LB 37 is designed for continuous operation. Just make sure the water tank is full before using it overnight.

How do I know if the filter needs to be replaced?

Regularly check the filter's condition. If you notice decreased performance or buildup, it is time to replace it.

The humidifier emits an unpleasant odor. What should I do?

This may be due to bacteria buildup. Thoroughly clean the device and tank, and change the water daily to prevent odors.

USER MANUAL LB 37 BEURER

Two beurer-shaped water heaters with metallic trim, one gray and one white, shown against a white background (no text or symbols visible)

Exploded diagram of a device with numbered parts for identification

Diagram of a container with labeled parts, showing liquid flow through a container with a hand inserting into it.

White ceramic bowl with a black arrow indicating rotation (no text or symbols)

Technical line drawing of a cylindrical capacitor with mounting base (no text or symbols)

i Hinweis

Read these instructions for use carefully and keep them for later use, be sure to make them accessible to other users and observe the information they contain.

WARNING

• This device may be used by children over the age of eight and by people with reduced physical, sensory or mental skills or a lack of experience or knowledge, provided that they are supervised or have been instructed on how to use the device safely, and are fully aware of the consequent risks of use.
  • Children must not play with the device.
• Cleaning and user maintenance must not be performed by children unless supervised.
• Disconnect the device from the mains supply during filling or cleaning.
• Do not use any solvent-based cleaning products.
• If the mains connection cable of this device is damaged, it must be disposed of. If it cannot be removed, the device must be disposed of.

Dear Customer

Thank you for choosing a product from our range. Our name stands for high-quality, thoroughly tested products for applications in the areas of heat, weight, blood pressure, body temperature, pulse, gentle therapy, massage, beauty, air and baby.

With kind regards,

Your Beurer team

Getting to know your device

Humans spend a large proportion of their time indoors.

For ideal ambient air, a humidity level of between 40 % and 60 % is recommended. This value is often not reached, particularly in winter, when cold, dry air enters living spaces that are being aired and is then warmed up.

This dry ambient air draws in moisture, drying out mucous membranes and skin, but also furniture.

Ambient air that is too dry may have a number of negative effects.

• Mucous membranes and lips dry out.
- Eyes become irritated.
- Infections and respiratory diseases are more likely to occur.
- Exhaustion, tiredness and difficulty concentrating.
• Pets and plants are put under unnecessary strain.
- Dust forms more quickly.
• Electrostatic charging of textiles made of synthetic fibres, such as carpets and plastic floor coverings.
- Wooden furniture and, especially, parquet floors, are damaged.
• Musical instruments go out of tune.

Table of contents

1. Included in delivery....13
2. Signs and symbols ......13
3. Warnings and safety notes....13
4. Intended use....14
5. Device description.....15
6. Initial use ....15

7. Usage 16

8. Cleaning and maintenance.....17

9. Accessories and replacement parts.....18
10. What if there are problems?....19
11. Disposal....19
12. Technical specifications .....19
13. Warranty / Service 20

1. Included in delivery

• Base unit for air humidifier
  • Water tank for air humidifier
• Cleaning brush
• Instructions for use
  • 15 Aroma pads

2. Signs and symbols

The following symbols appear in these instructions for use:

	WARNINGWarning instruction indicating a risk of injury or damage to health		Manufacturer
	IMPORTANTSafety note indicating possible damage to the device/accessory		CE labellingThis product satisfies the requirements of the applicable European and national directives.
	Product informationNote on important information		Dispose of packaging in an environmentally friendly manner
	Read the instructions		Certification symbol for products that are exported to the Russian Federation and members of the CIS
	Disposal in accordance with the Waste Electrical and Electronic Equipment EC Directive – WEEE

3. Warnings and safety notes

Read these instructions for use carefully. Non-observance of the following information may result in personal injury or material damage. Store these instructions for use and make them accessible to all users. Make sure to include these instructions for use when handing over the device to third parties.

Electric shock

WARNING

As with every electrical device, use this air humidifier carefully and cautiously, in order to avoid hazards due to electric shock.

• Only operate the device at the voltage indicated on the device (the type plate is located on the underside of the base unit).
• Only insert the mains cable into the socket when the device is switched off.
• Never use the device if it or its accessories are visibly damaged.
• Do not use the device if it has sustained a fall or if water has penetrated the device interior.
• Do not use the device during a storm.
• In the event of defects or operational faults, switch off the device immediately and disconnect the device from the mains socket.

• Do not pull on the mains cable or on the device to disconnect the plug from the socket.

• Never hold or carry the device by the mains cable.

• Do not clamp or pinch the mains cable.
• Keep the mains cable away from hot surfaces.
• Ensure that the mains cable and plug do not come into contact with water, steam or other liquids.
• Only use the device in dry internal rooms (e.g. never in the bathroom, sauna, etc.).
• Never reach for a device that has been submerged in water. Pull the plug out of the mains socket immediately.
• Do not subject the device to any impacts or drop the device.

Repairs

WARNING

• Do not open the base unit.
• Only specialist personnel may perform repairs on electrical devices. Improper repairs may subject users to considerable danger. For repairs, please contact customer service or an authorised retailer.
• If the mains cable of the device is damaged, it must be replaced by the manufacturer or an authorised customer service point.

Risk of fire

WARNING

There is a risk of fire if the device is used improperly or these instructions for use are ignored.

• Never use the device underneath a cover, such as a blanket or pillow.
• Never use the device near highly flammable substances.

Operation

WARNING

• The device is only intended for the purpose described in these instructions for use. The manufacturer is not liable for damage resulting from improper or careless use.
• This device is not intended for use by people (including children) with restricted physical, sensory or mental skills or a lack of experience and/or a lack of knowledge, unless they are supervised by a person who has responsibility for their safety or instructed by him in how to use the device.
  • Children should be supervised around the device to ensure they do not play with it.
  • If you suffer from a severe respiratory or lung disease, consult your doctor before using the air humidifier.
• The device must be switched off after every use and before cleaning. Pull the plug out of the mains socket.
• Ensure that the mains cable does not pose a trip hazard.

IMPORTANT

• Ensure that the device is placed on a firm, flat surface that is not susceptible to moisture.
• Do not insert any objects into openings on the device. Ensure that the moving parts can move freely at all times.
• Do not place any objects on the device.
• Do not expose the device to high temperatures.
• Avoid direct sunlight.

4. Intended use

This air humidifier is designed for the humidification of ambient air. The device is intended for private use.

5. Device description

The air humidifier

• humidifies the air,
• quiet operation,
  • is suitable for rooms up to 20 m² in size,
• has a low energy consumption and switches off automatically when the water tank is empty,
• is easy to clean,

• features a night mode.

• Mist outlet

• Water tank
• Water tank screwed plug
• Water basin
• Base unit for air humidifier
• Ultrasound membrane
• ON/OFF button with LED display
• Aroma compartment

Exploded diagram of a device with numbered parts for identification

Principle behind the LB 37 air humidifier

1. High-frequency vibrations release tiny drops from the surface of the water.
2. The fan draws in air through the aroma compartment on the side of the device.
3. Water evaporation can also be switched on.
4. If you wish, the device can be used with aromas.

6. Initial use

Unpacking the device

WARNING

Diagram of a container with labeled parts, showing liquid flow through a container with a hand holding a container.

Keep packaging material away from children! There is a choking hazard.

• Open the cardboard packaging.
• Remove the protective insert.
• Keep the plastic film closed.
• Lift the device up and out of the packaging.
• Remove the plastic covering.
• Check the device, the mains plug and the cable for damage.

Installation location

WARNING

Before putting the device into operation, read the safety notes in the Safety chapter.

Note

• The immediate vicinity of the air humidifier can become damp.
  • Calcareous water can leave white deposits.
• Do not place the device on the floor, but in a raised position (e.g. on a table or chest of drawers).
• Position the device so that the mist outlet is not directed towards objects.
  • Empty any remaining water when the device is not in use.
• Place the air humidifier on a firm, level and water-resistant surface.
  If the device should accidentally tip over, water may escape, even if the device is switched off and unplugged.

Water

Note

• Do not add any essential oils or fragrances to the water. If additives are used, the plastic material may become discoloured and damaged. The ultrasound membrane gets stuck and is damaged.
• Use fresh drinking water below 40^ C in the device. If the drinking water is very hard, you can use demineralised or distilled water.
• Tip! If the water is hard, we recommend using the optional anti-limescale filter.

Filling the water tank

• Lift the water tank and rotate it.
  The water tank is kept closed by means of a spring valve.
• Open the screwed plug on the water tank.
• Fill with water.
  The water tank holds a maximum of 2 litres.
• Tightly close the water tank using the screwed plug.
• Rotate the water tank and position it on the base unit.
  The tank should sit tightly on the base unit.

7. Usage

Note

Check the humidity of your ambient air regularly. Intensive continuous operation can cause the ambient air to become excessively humid. The relative air humidity should not exceed 60 %.

Switching on the device

• Insert the plug into the mains socket.
• If there is no or not enough water in the water tank, a red LED lights up.
  The device has switched off for safety reasons.
• Fill the water tank.
  Fill the water tank as described under 5. Initial use.

Hinweis

The device has three different modes:

LED lighting Air humidifiers Evaporation output
Press the ON/OFF button (1)1x	blue Level	1 ~ 200 ml/h
Press the ON/OFF button (1)2x	white Level	2 ~ 150 ml/h
Press the ON/OFF button (1)3x (Night mode)	OFF Level	2 ~ 150 ml/h
Press the ON/OFF button (1)4x	OFF	OFF	-

Note

You may optionally add drops of aroma/scented oils to the aroma compartment (8). These will lend a pleasant odour to the room. Under no circumstances should you add the aroma directly to the water.

Switching off the device

• Press the ON/OFF button ( )4 times. The LED lighting goes off.
• Pull the plug out of the mains socket.

Note

In night mode, the air humidifier operates in level 2 with a lower evaporation output and no LED illumination to ensure undisturbed and therefore restful sleep.

8. Cleaning and maintenance

Regular cleaning and disinfection are a prerequisite for hygienic and fault-free operation.

The level of contamination of the device depends on the water quality and how long it has been in operation. In any case, we recommend the following cleaning intervals.

Every three days As	required
x Clean the ultrasound	and membrane	with a brush, rinse the base.
x Rinse the water tank	tank, replace the water.
	x Clean the air humidifier inside and out.
	x Descale.

WARNING

The device must be switched off after every use and before cleaning. Pull the plug out of the mains socket.

IMPORTANT

The water tank must be cleaned and the air humidifier completely emptied if the device has not been used for over a week.

Note

• Clean the device using only the methods specified.
  • Under no circumstances may liquid enter the base unit.
• Do not use any solvent-based cleaning products.
• Only use a mild flushing agent or vinegar/vinegar-based cleaner to perform cleaning or disinfection work.

Cleaning the ultrasound membrane with a brush, rinsing the base

Note

Empty the water from the base unit via the side rim in the direction indicated by the arrow. Ensure that no water gets inside the device, e.g. via the fan opening.

• Clean the ultrasound membrane using the cleaning brush provided.
• Empty the water from the base unit via the side edge.
• Should dirty residue remain in the base unit, pour some clean, fresh water into the base unit and empty it out via the side edge.

White ceramic bowl with a black arrow indicating rotation or movement (no text or symbols)

Rinsing the water tank, replacing the water

• Clean the water tank regularly, at least once a week if using daily.
• Use a mild cleaning agent or vinegar/vinegar-based cleaner.
• Clean the thread of the screwed plug using a soft brush.
  • Half-fill the water tank with water.
• Tightly close the water tank using the screwed plug.
• Shake the water tank by rocking it back and forth several times.
  • Empty out the water completely.
• Repeat the process using clean, fresh water.

Cleaning the air humidifier inside and out

• Empty the water from the base unit via the side edge.
- Wipe the air humidifier with a damp cloth inside and out.
- Only use a mild flushing agent or vinegar/vinegar-based cleaner to perform cleaning work.

Descaling

Descaling the ultrasound membrane

Hard water can cause limescale to build up in the device and, especially, on the ultrasound membrane. This forms white deposits. Descale the device regularly.

• Drop some descaler onto the ultrasound membrane.
• Leave it to take effect for two to five minutes.
• Clean the ultrasound membrane using the cleaning brush.
• Rinse the base unit twice with clean, fresh water.

Cleaning inside the base unit

• Dip a damp, soft cloth briefly in descaling solution.
• Use the cloth to wipe the inside of the base unit.
- Carefully pour some clean, fresh water into the base unit.
• Empty the water from the base unit via the side edge.
- Repeat the process using clean, fresh water.

Descaling the water tank

• Half-fill the water tank with water.
- Add a small quantity of descaler.
- Tightly close the water tank using the screwed plug.
- Shake the water tank by rocking it back and forth several times.
• Empty the descaling solution completely.
- Repeat the process twice using clean, fresh water.

9. Accessories and replacement parts

Tip!

If the water is hard, we recommend using the optional anti-limescale filter. Anti-limescale filter (optional).

Note

Technical line drawing of a cylindrical electronic component with mounting base (no text or symbols)

• If the anti-limescale filter does not prevent limescale build-up, or if white deposits form on or in the device, the anti-limescale filter should be replaced.
  • The service life of the anti-limescale filter is around two to three months at most.
• If the device is not used for a relatively long time, the anti-limescale filter must be removed from the water tank and dried out.

Fitting the anti-limescale filter

• Lift the water tank and rotate it.
• Open the screwed plug on the water tank.
• Screw the anti-limescale filter onto the screwed plug on the inside.
• Tightly close the water tank using the screwed plug.

Replacement items

For replacement parts and additional items visit www.beurer.com or contact the corresponding service address in your country (according to the service address list).

Replacement parts and additional items are also available from retailers.

Item Item number
Beurer by Taoasis “Vitality” aroma oil (10 ml) 681.30
Beurer by Taoasis “Harmony” aroma oil (10 ml) 681.31
Beurer by Taoasis “Relax” aroma oil (10 ml) 681.32
Beurer by Taoasis “Sleep Well” aroma oil (10 ml) 681.33
10 aroma pads 163.801
Anti-limescale filter (optional) 163.803

1. What if there are problems?

Problem Cause Solution
No LED display The mains cable is not plugged in. Connect the plug.
Red LED The water level is too low; the wa-ter tank is empty.		Fill the water tank.
No mist is produced The LED display lights red . Fill the water tank.
The LED display does not light up.
The mist has a strange smell	The device is new.	Remove the water tank, turn the screwed plug and remove it.Air the open, emply water tank in a cool, dry place for twelve hours.
	Stale or dirty water.	Empty the base unit and the water tank and clean them thoroughly.Fill the water tank with fresh water.
Strange noise	The water tank is not positioned correctly on the base unit.	Lift up the water tank and position it correctly on the base unit.The tank should sit tightly on the base unit.
	There is too little water in the water tank.	Fill the water tank.
	The device is not level and unstable.	Place the device on a firm, level surface.
Mist escapes underneath the water tank	The water tank is not positioned correctly on the base unit.	Lift up the water tank.Check whether the join between the base unit and water tank is clean.Clean if required.Position the water tank correctly on the base unit.The tank should sit tightly on the base unit.
The LED lights up red although the tank is full	The device evaluates the water level incorrectly due to a fault.	Restart the device.

11. Disposal

For environmental reasons, do not dispose of the device in the household waste at the end of its useful life. Dispose of the unit at a suitable local collection or recycling point. Dispose of the device in accordance with EC Directive – WEEE (Waste Electrical and Electronic Equipment). If you have any questions, please contact the local authorities responsible for waste disposal.

1. Technical specifications

Dimensions (LxWxH) approx.	21 cm x 11 cm x 25,5 cm
Cable length approx. 1.5 m
Mains voltage/frequency	100 –240 V AC / 50/60 Hz
Nominal power	max. 20 W
Room size	up to 20 m^2
Capacity	approx. 2 litres
Evaporation output	200 ml/hour
Signs and symbols	☐ The unit is double-protected and thus corresponds to protection class 2.
Volume	approx. 35dB

13. Warranty / Service

Beurer GmbH, Söflinger Straße 218, 89077 Ulm, Germany (hereinafter referred to as "Beurer") provides a warranty for this product, subject to the requirements below and to the extent described as follows.

The warranty conditions below shall not affect the seller's statutory warranty obligations which ensue from the sales agreement with the buyer.

The warranty shall apply without prejudice to any mandatory statutory provisions on liability.

Beurer guarantees the perfect functionality and completeness of this product.

The worldwide warranty period is 3 years, commencing from the purchase of the new, unused product from the seller.

The warranty only applies to products purchased by the buyer as a consumer and used exclusively for personal purposes in the context of domestic use.

German law shall apply.

During the warranty period, should this product prove to be incomplete or defective in functionality in accordance with the following provisions, Beurer shall carry out a repair or a replacement delivery free of charge, in accordance with these warranty conditions.

If the buyer wishes to make a warranty claim, they should approach their local retailer in the first instance: see the attached “International Service” list of service addresses.

The buyer will then receive further information about the processing of the warranty claim, e.g. where they can send the product and what documentation is required.

A warranty claim shall only be considered if the buyer can provide Beurer, or an authorised Beurer partner, with

• a copy of the invoice/purchase receipt, and
• the original product.

The following are explicitly excluded from this warranty:

• deterioration due to normal use or consumption of the product;
• accessories supplied with this product which are worn out or used up through proper use (e.g. batteries, rechargeable batteries, cuffs, seals, electrodes, light sources, attachments and nebuliser accessories);
• products that are used, cleaned, stored or maintained improperly and/or contrary to the provisions of the instructions for use, as well as products that have been opened, repaired or modified by the buyer or by a service centre not authorised by Beurer;
• damage that arises during transport between manufacturer and customer, or between service centre and customer;
• products purchased as seconds or as used goods;
• consequential damage arising from a fault in this product (however, in this case, claims may exist arising from product liability or other compulsory statutory liability provisions).

Repairs or an exchange in full do not extend the warranty period under any circumstances.

FRANÇAIS

Exploded diagram of a device with numbered parts for identification

Diagram of a container with labeled parts, showing liquid flow through a funnel and tank.

White ceramic bowl with a black arrow pointing to the side of its rim (no text or symbols)

Technical line drawing of a cylindrical capacitor with mounting base (no text or symbols)

Remarque

Diagram of a container with labeled parts, showing liquid flow through a funnel and a side pipe.

ADVERTENCIA

White ceramic bowl with a black arrow indicating rotation or movement (no text or symbols)

Technical line drawing of a cylindrical electronic component with mounting base (no text or symbols)

Nota

Diagram of a container with labeled parts, showing liquid discharge from a tank and a valve inside.

White ceramic bowl with a black arrow pointing to the side of its rim (no text or symbols)

Technical line drawing of a cylindrical capacitor with mounting base (no text or symbols)

Note

Exploded diagram of a device showing exploded view with numbered parts for identification

Hava nemlendirici LB 37 prensibi

Diagram of a container with labeled parts, showing liquid discharge from a container and a manometer inserted into the liquid.

White plastic bowl with a black arrow pointing to the side of its side (no text or symbols)

Su haznesini doldurun, suyu tazeleyin

Technical line drawing of a cylindrical capacitor with mounting base (no text or symbols)

Not

Diagram of a filtration or separation device with labeled components 1, 2, 3, and 4

White ceramic bowl with a black arrow pointing to the side of its rim (no text or symbols)

Technical line drawing of a cylindrical electronic component with mounting base (no text or symbols)

Exploded diagram of a device with numbered parts for identification

Diagram of a container with labeled parts, showing liquid flow through a funnel and outlet with a drain.

White plastic appliance with a black arrow indicating rotation or movement (no text or symbols)

Technical line drawing of a cylindrical electronic component with mounting base (no text or symbols)

Wskazówka