iCMPFM2T03 - Flat screen mount Chief - Free user manual and instructions

Brand	Chief
Model	iCMPFM2T03
Product Type	Wall Mount for Flat Screen
Maximum Load	56.7 kg (125 lb)
Material	Steel
Model Compatibility	iCMPFM2 (fixed) and iCMPTM2 (tilt)
Mounting Type	On Wood Stud or Concrete Wall
Minimum Distance Between Wall Plates	304.8 mm
Drill Diameter for Wood	5.5 mm
Drill Diameter for Concrete	10 mm
Fasteners Provided	Lag Bolts, Washers, Anchors
Tilt Function	Yes (iCMPTM2 model only)
Horizontal Adjustment	Sliding Rails
Required Structural Capacity	5 times the total supported weight
Safety	Avoid electrical cables and gas lines during installation
Maintenance	Clean with a damp cloth
Use	Indoor
Plate Switching	Possible to adapt button location

Frequently Asked Questions - iCMPFM2T03 Chief

What is the maximum weight supported by the mount?

The iCMPFM2T03 mount can support a maximum weight of 56.7 kg (125 lb) for the entire TV and attached accessories.

Can I install this mount on a drywall wall?

No, the mount is designed to be mounted directly on a wood stud or concrete wall. The maximum drywall thickness is 16 mm, but the mount must be fixed into a load-bearing stud.

How to install the mount on a concrete wall?

For installation on concrete, drill 10 mm pilot holes at the marked locations, insert the supplied anchors (J1) using a hammer, then secure the mount with lag bolts (J3) and washers (J2). Ensure the wall can support 5 times the total weight.

Can the interface brackets be swapped?

Yes, if necessary, the left and right interface brackets can be swapped to place the tilt buttons inside the mount. Follow the swap steps described in the manual.

How to tilt the screen with the iCMPTM2 model?

For the tilt model, loosen the button on the interface bracket, adjust to the desired tilt, then tighten the button. Make sure the screen is locked after adjustment.

What is the minimum distance between the wall plates?

The minimum horizontal distance between the wall plates is 304.8 mm. Do not install the plates closer than this distance.

What tools are needed for installation?

You will need a level, a drill, drill bits of 5.5 mm (wood) or 10 mm (concrete), a hammer (for concrete anchors), appropriate wrenches for the bolts, and possibly a screwdriver.

What if the provided screws do not fit my TV?

Choose correctly sized screws from the hardware bag (H). If spacers are needed, use longer screws of the same diameter. Screws should thread easily and fully into the TV mounting holes.

Is the mount compatible with all flat screens?

The mount is designed for flat screens compatible with iCMPFM2 and iCMPTM2 models. Check that your TV respects the maximum load capacity of 56.7 kg and that the interface brackets can be securely attached to the back of the screen.

How to clean the wall mount?

Use a damp cloth to clean the mount. Do not use abrasive or chemical products that could damage the finish.

USER MANUAL iCMPFM2T03 Chief

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.

IMPORTANT WARNINGS AND CAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer's responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8 (1.6cm).

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all components attached to the iCMPFM2/iCMPTM2 does not exceed 125 lbs (56.7 kg).

AVISOS Y PRECAUCIONES IMPORANTES!

BAXHBIE INPEDYNIPEXJEHIN I PEPDOCTEPEKHEHIN

PENPYTPEKDEHNEI PEPYTPEKEHNEIpeBnOaRIM 8TOBHOCTBACXBOOMHOCTNOpEBe3HOpaBnIINM OEMPH,ECM BHe CnDyTe 3A HcTPOUAA

PNDYPTPEKDEHE. OXtAOKEeHbAaApekBAtyHX CTpykTyPOOcN 3TOI K0OMTHAEHTMOKETNPABCTN K cep3bONMY TENECHOMY NOBpEXDHNIOI NnOBpeTb HA OoOpydAnHe! 3TO -OTBCTTEHOHOCBT MOHTAXHNA YQoDCOEPBnTRC CTpykTyPA, K KOtOPARnpNOKHE 3TOI KOHOMHT, MOKET NODqEpaKbR pAS p3aO6bJenHHH Bec aecero o6OpODAHBA. Xypenite CTpykTyPK A Tpebyetr nepd MOHTAKOM KOMHOENTA.TOniHa HwyATyPAHn HA CTHEK, K KOtOPARpETCRKxPOHHTEH, DPOHKA coctanrBa He bOeae1.6 CM

PNEYPTPEKHEHNE. PnBbIeHHeAEMCTMOCHTBeCa MOXETnpBAACTNcOpebHOaHMyTeCHOMy NOBpEeHHN HINoBpEepTbHaOBcpOyDaHMe13To-OTAECTBEHCOHT MONTAHKIAQDCTOBEPVTCA, YTO OFbIeHHN BEC BoX KOMMOHHTo, pnoNKeHHxKICMPFM2ICMTPM2 He npBbaee125 yHToTb(56.7K).

VIGTIG ADVARSLER OG FORHOLDSREGLER!

1

INSTALLATION The iCMPFM2 and iCMPTM2 have been designed to be mounted directly onto either a wood stud or concrete wall. The iCMPFM2 has static brackets which keep the TV in an upright position. The iCMPTM2 has brackets which allow the TV to be tilted. WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the mount is being attached is capable of supporting five times the weight of the iCMPFM2 or iCMPTM2 and all attached equipment not to exceed 125 lbs (56.7 kg). Assembling the Wall Mount 1. Place both wall uprights (F) on the floor. 2. Slide rails (A) into wall uprights. 3. Thread endcaps (G) into the end of each rail. NOTE: Proceed to either the Installing to a Wood Stud Wall (2a) section or the Installing to a Concrete Wall (2b) section.

2a

Installing to a Wood Stud Wall 4. Determine the center of the TV screen, and where it should be located on the wall. 5. Locate the closest stud to the left and right of the selected location. NOTE: If the screen area lies over a stud, use that stud and the stud to either the left or right of it. 6. Line up the diamond on mount with center of screen marking to determine vertical center. 7. Measure up 6" from the center point to mark location of the upper mounting slots.

2b

Installing to a Concrete Wall

1. Determine the center of the TV screen, and where it should be located on the wall.
2. Line up the diamonds on mount with center of screen marking to determine vertical center.
3. Measure up 6'' from the center point to mark location of the upper mounting slots.

CAUTION: MINIMUM HORIZONTAL DISTANCE BETWEEN WALL BRACKETS IS 12". Do not place mounting brackets closer together than 12".

WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.

WARNING: EXPLOSION AND FIRE HAZARD! CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.

2b

1. Using a level, mark the wall through both upper mounting slots.
2. Drill one 25 / 64'' (10mm) pilot hole at each marking.
3. Install an anchor (J1) into each pilot hole using a hammer.
4. Use two 5 / 16 × 2 - 1 / 2 lag bolts (J3) and two 5 / 16 flat washers (J2) to attach top of mount to anchors in wall.
5. Mark the attachment points for the lower mounting slots.
6. Drill one 25/64" (10mm) pilot hole at each marking for lower mounting holes.
7. Install an anchor (J1) into each pilot hole using a hammer.
8. Use two 5 / 16 × 2 - 1 / 2 lag bolts (J3) and two 5 / 16 flat washers (J2) to attach the mount to the wall through the lower mounting holes.
9. Slide rails to approximate center of screen location.

3

Attaching Interface Brackets to TV

1. Align the center of the bracket with center of screen.

NOTE: The diamond-shape hole in the bracket corresponds to the center of the mount.

WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display. Properly sized screws will easily and completely thread into display mounting holes. If spacers are required, be sure to use longer screws of the same diameter.

1. Select correct screws, spacers (if necessary) and universal washers from the hardware bag (H) and attach brackets to back of screen.

Switching Interface Brackets (Optional)

If an installation situation makes adjusting the location of interface brackets necessary, there are several options.

1. The wall brackets may be adjusted side to side at the point of attachment.
2. The location of the left and right interface brackets may be switched, with the knobs on the iCMPTM2 interface brackets facing the inside of the mount.
3. If necessary, the tilt interface bracket knobs may be switched to allow the interface brackets to be reversed.

a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right interface bracket horizontally, tightly gripping it so that spacers do not move.
d. Remove the knob, washer and screw.
e. Replace the knob, washer and screw in the opposite order, with the knob on the inside of the bracket.
f. Switch the right interface bracket to the left side of the wall mount.
g. Repeat Steps 3c through 3f with the left interface bracket.

Tilting the Interface Brackets (ICMPTM2 only)

The brackets may be tilted by loosening the knob on the brackets, tilting to desired location, and tightening knob on the brackets.

5

NEVER place both interface brackets to one side of the wall mount center line (CL)!

Both interface brackets must NEVER be located to one side of the wall brackets!

(Screen not shown for clarity)

Attaching Screen to Wall Mount

1. Adjust Velcro® pull strap (if necessary) so it does not extend beyond bottom of screen.

NOTE: Do NOT allow both interface brackets to be located on same side of wall bracket.

NOTE: NEVER place both interface brackets to one side of the wall mount center line!

1. Hang top hook of interface brackets onto the top bar of the mount.

NOTE: The screen initially installs into the "kickstand mode" to allow easy cable access.

1. Slide screen and bars to desired viewing position.

2. Route cables between wall and bars.

CAUTION: PINCH POINTS! Keep fingers, hands and cables out of pinch point areas.

1. Pull downward on the pullstraps and swing inward toward wall, latching interface brackets to lower bar and locking bottom of screen to the mount.

Haknoh CoedHHHTbeBbHx KPOHHTeHOB (ToHko B Moden (CMPTM2)

KpOHTeHbMoHO HAcHOHTb. Dn stOro ocna6bepeyIaTOpb KpOHTeHbHO.HAHOHTe KpOHTeHbB HkyHOeNPOKHeHm 3aHHInTe peryTAtOpb Ha KpOHTeHaxdoynopa

5

Cpehnnn (CL)

YcTaHOBbKa 3KpaHa B HAcTeHHy OChTeMy KpenneHn

1. Otperympyte pny kpenexno nenty Velco (pnp Hoo6doMOCT) TAK,HTo6OHa HE BucTypana 3A HNOH Kpaik kpaik
   PINPMEYAHNE.3ANPEHEOpaMeaubObaa0oDHNHTBbHxKPOHHTeKaNoOdyCTOPOHyOTNtHEHOROMONTAHHORKPOHHTeKa.
   PIMMEYAHNE.3APNEEHOpaMeaTbO6a 00eHNHTBnKXPOHHTeHaNO OyH CTOPOHOTcpeHnNnKtAENHO 0CTEMbKPENHEI
   2.Пав�сье ворхину димы саддимпгштбнвь Вархину рожу саддимы креллеси.
   PIMMEYAHNEIpeoHaHbHOxHApYCTaHbAeBaTeor HANHEKOTOPMpaCTOHRNnOCTCHB（KAK npwncno3AOHHoONOp） TO6bOblenntbDcTynKk6eNo.
   3.YcHbOvBte kaphnpekpoa nnonoxenHe,Hyxhoe dna npocmorpa aaoo6paehenes
2. Ilponokite kabei Mexdy cte Hoi pekann

A

3ANPUEHEOpaMeaTb oba coeMHHTenbHxKpOHHeHaNo odnyctopOHy cTepeHHN(HCL) HACTEHNOCTeHHMKN

3JAPTEJEHO paaMaaatb 06a coeHHHtBnBHX KPOHHTEHa No any CTPOHY OTHACTEHbIX MOANTKHX KPOHHTHEH!

OPOXHO! 3OHbI 3AUEMNHEHr Cnqte 3a
TO6bI naBmu pyu KABeH He nnonadn B 3Hb
THeH
5. TnHHTe KENKHOB NHTMBAH3 3ABEPHEK X C TcHEn -TaAMObAPoAM Bly PnRINPEOT COEHNNTBHe HPOXHTBk H K Epeke X TaqDIOKpyTe HNOH KpAekpa BCACTMeKPNENHJI.

USA·8401 Eagle Creek Parkway, Suite 700·Savage, Minnesota 55378·800.572.1373

EMEA·[phone]

www.icmounts.com

©2009 Milestone AV Technologies. The iC Logo and StowAway are trademarks of Chief Manufacturing, a products division of Milestone AV Technologies, a Duchossois Group Company. All rights reserved Patents and patents pending. Milestone AV Technologies, Savage, MN 55378, USA

8805-000268 Rev 01

05/09