DR 564 CD - CD Player CLATRONIC - Free user manual and instructions

USER MANUAL DR 564 CD CLATRONIC

General safety instructions

Use the device only for the intended purpose.

Only connect the device at a properly installed plug socket. Pay attention that the specified voltage corresponds to the voltage of the plug socket.

When using external mains supply, pay attention to the correct polarity and voltage. Always place the batteries in the correct direction.

Assemble the device in such a way that the available ventilation openings are not covered.

Never open the housing of the device. Incorrect repairs can constitute a considerable risk for the user. Should the device become damaged, in particular the mains supply cable, do not operate the device any longer, but rather have it repaired by an expert. Check the mains supply cable regularly for damage.

For safety reasons a broken or damaged mains lead may only be replaced by an equivalent lead from the manufacturer, our customer service department or a similar qualified person.

If the device is not used for a longer period, remove the plug connector from the plug socket or take out the batteries.

These symbols may be found on the machine and are intended to indicate the following:

The lightning symbol should advise the user of parts in the inside of the device which carry dangerously high voltage levels.

The symbol with an exclamation mark should advise the user of important operation or maintenance instructions in the accompanying documentation.

Devices bearing this symbol work with a „class 1 laser“ for tracing the CD. The built-in safety switches should prevent the user being exposed to dangerous laser light, which is invisible to the human eye, when the CD compartment is opened.

Under no circumstances should these safety switches be bypassed or manipulated, as this could result in a danger of exposure to the laser light.

Wall Installation

• The device can also be mounted on the wall. To do so, measure the distance between the two indentations and drill two holes at the same horizontal distance from one another.
• Please ensure beforehand that you will not damage any electric cables that are hidden in the wall! Then insert rawplugs and screws into the drilled holes.
• Hang up the device and check that it is securely in place.

Overview of the components

1 Carrying belt

14 Frequency scale

2 CD compartment

15 LED display

3 CD compartment flap

16 Function selector switch (FM ST./AM/CD)

4 PROG button

17 ST. control lamp

5 REPEAT button

18 REP control lamp

6 REW button (fast rewind)

19 PROG control lamp

7 F.FWD button (fast forward)

20 POW. control lamp

8 VOLUME / volume regulator

9 Function selector switch ON/OFF POWER

Reverse side

10 STOP button

21 PHONES (Headphone connection)

11 PLAY/PAUSE button

22 DC 9 V socket

12 Regulator TUNING

23 Foot

13 OPEN / button for opening the CD compartment

24 Suspension device

25 Battery compartment

Commissioning the device

Battery Mode (not supplied)

• Open the battery compartment (25) on the back of the machine by turning the screw in the direction of OPEN.
• Insert 8 1.5V AA type batteries. Match the polarities correctly (see the inside of the battery compartment).
• Close the battery compartment (LOCK).
• If the device is not used for a long period of time, remove the batteries to avoid the "spilling" of battery acid.
  Always change the battery set completely, do not change just one battery.

Warning: batteries are not to be disposed of together with domestic wastes.

Dispose of the used batteries at the relevant collection bin or at your dealer's.

Never throw batteries into the fire.

AC Adapter Mode (not supplied)

You can also use the device with an adapter.

1. Insert the AC adapter into a duly installed 230V/50Hz protective contact outlet.
2. Connect the device to the power supply unit by inserting the plug of the supply unit into the 9 V DC socket (22).
3. If a power supply unit is used, please ensure correct polarity as shown by the inscription on the device.
4. If you have connected a power supply unit, the batteries are automatically switched off.

GB

Spray water proof

The device is spray water proof. It can hence be used also in the shower. Owing to the fact that the housing is protected against water spray, the VOLUME and TUNING regulators are somewhat stiff.

Caution: Please note that in the shower or bath the device may only be used on battery power.

Note: Always make sure that the device is dry when changing a CD or the batteries

General Operating

Suspension device / foot (24/23): ON OFF POWER (9):

Hang up the device or place it on its foot. Switches the unit to "ready for operation" or to "off". The POW control lamp (20) shows the function.

VOLUME (8):

Is used to set the volume of the music.

9 V socket (22):

For connecting a mains adapter.

PHONES (21):

For connecting head- or earphones.

Switching off

The device is switched off by turning the function selector switch (9) to OFF.

Playing CDs

1. If the OPEN button (13) is pushed down the CD compartment opens.
2. Insert a CD with the label facing upwards and press carefully over the button until it snaps into place. Please close the CD compartment flap (3).
3. Turn the function selector switch (16) to the CD position
4. Press the PLAY/PAUSE button (11) to start the playback. "--" appears in the display followed by the number of tracks.. The CD starts from the first track. The track currently being played and the time that has elapsed are shown in the display.
5. To remove a CD, press the STOP key (10), open the CD deck with the OPEN key and take out the CD carefully.

Always keep the CD deck cover closed.

Description of the CD buttons

PLAY/PAUSE (11):

You can briefly interrupt the playing. Renewed pressing of the button will re-start the playing from the same place.

REW (6):	Press once = This starts the current track again from the beginning. Press a second time = This jumps back to the previous track. Press a third time = This plays the song before etc. If the button is kept pressed down, the machine starts to search through the tracks.
F.FWD (7):	With this button you can jump to the following track or the next track but one etc. If the button is kept pressed down, the machine starts to search through the tracks.
STOP (10):	The CD is stopped.
REPEAT (5):	The following functions can be selected with the REPEAT button Press once = The REP control lamp (18) flashes in the display. The current track is repeated continuously. Press a second time = The REP control lamp lights up in the display. The whole CD is played continuously. Press a third time = All the functions are reset. The normal play mode is resumed.

GB

Programmed Play

1. Press the STOP key.
2. Press the PROG key (4).
3. The PROG (19) control lamp flashes in the display together with "01" (track number).
4. Use the REW/F.FWD buttons to select the desired track and then press the PROG button again.
5. The display changes to memory slot 02.
6. Use the REW/F.FWD buttons to select the next track and press the PROG button again. Repeat the procedure until all the desired tracks are selected.
7. Press the PLAY/PAUSE key. The PROG control lamp lights up in the display. The playback starts. Press this button to pause briefly the playback.
8. Press once the STOP key to stop the playback while retaining the program.
9. To resume the playback of the program press first the PROG key once and then the PLAY/PAUSE key.
10. To delete the program, press the STOP key twice.

The device stops automatically once the entire sequence of programmed tracks is completed. The programmed order of tracks remains in the memory until you delete the programme, remove the CD from the CD compartment or switch off the machine. In order to play the programmed order of tracks again, first press the PROG and then that PLAY/PAUSE button.

GB

It is possible to combine the programmed tracks with the REPEAT function. After you have programmed and started the device, please press the REPEAT button up to three times. You can now use the functions described in the "REPEAT" section.

Listening to the Radio

1. Turn the function selector switch (16) to the FM ST or AM position.
2. With this switch you can select the desired frequency band.
3. UKW = FM ST., medium wave = AM (mono).
4. Tune in the desired station with the station adjustment knob TUNING (12).
5. The stereo control lamp (17) only lights up if you have selected FM stereo and the station is being received in stereo quality. If reception is too weak and the station being received is subject to interference, it is possible that this lamp will not light up. If it is not possible to improve reception it is advisable to try a change of location.
6. To receive MW/AM stations proceed in the same manner. In this frequency band programs are transmitted in "mono" only.

Note: An aerial is integrated in the device for the reception of FM ST/AM stations. The device can be aligned to the transmitter by turning and changing its position.

Cleaning and storage

• Clean the device with a moist cloth and dry it well.
• Do not use abrasive detergents!
• If the device is not used for a long period of time (a few months), the battery is to be removed from the battery compartment to avoid the „spillage“ of the battery acid.

This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Subject to technical changes without prior notice!

Guarantee

The device supplied by our Company is covered by a 24 month guarantee starting on the date of purchase (receipt).

During the life of the guarantee any fault of the device or its accessories *) ascribable to material or manufacturing defects will be eliminated free of charge by repairing or, at our discretion, by replacing it. The guarantee services do not entail an extension of the life of the guarantee nor do they give rise to any right to a new guarantee!

Proof of the guarantee is provided by the proof of purchase. Without proof of purchase no free replacement or repair will be carried out.

For repairs or replacement during the life of the guarantee return the device in its original packing together with the proof of purchase to your dealer.

*) Damage to accessories does not mean automatic free replacement of the whole machine. In such cases please contact our hotline. Broken glass or breakage of plastic parts are always subject to a charge.

Defects to consumables or parts subject to wearing (e.g. motor pistons, kneading blades, drive shafts, spare remote control, spare toothbrushes, saw blades, etc.) as well as cleaning, maintenance or the replacement of said parts are not covered by the guarantee and hence are to be paid!

The guarantee lapses in case of unauthorized tampering.

After the expiry of the guarantee

After the expiry of the guarantee repairs can be carried by the competent dealer or repair service against the payment of the ensuing costs.

PL