UP-DF750 - Printer SONY - Free user manual and instructions

Brand	Sony
Model	UP-DF750
Product Type	Professional digital printer
Print Technology	Thermal dye sublimation
Print Resolution	Up to 300 dpi
Dimensions (W × D × H)	Approx. 400 × 350 × 200 mm
Weight	Approx. 12 kg
Power Supply	100-240 V AC, 50/60 Hz
Power Consumption	Max. 150 W (operating), less than 10 W (standby)
Supported Paper Formats	Sony specific paper UPP-110S and UPP-110HD
Interface	USB 2.0, Ethernet (optional)
Main Functions	High-quality printing, automatic image correction, flexible layout
Maintenance and Cleaning	Regular cleaning of the print head with the supplied kit
Safety	Mandatory grounding, automatic shutdown in case of overheating
Spare Parts and Repairability	Parts available via Sony after-sales service
General Information	User manual available for free download at notice-facile.com

Frequently Asked Questions - UP-DF750 SONY

How many pages can I print with one set of consumables?

With a standard paper and ink ribbon kit, you can print approximately 100 pages (10x15 cm format). The exact number depends on the paper size and type.

How do I clean the print head of my UP-DF750?

Use the supplied cleaning kit. Follow the procedure in the manual: insert the cleaning sheet into the feeder and start the cleaning cycle from the menu. Repeat if necessary.

What should I do in case of a paper jam?

Turn off the printer, open the top cover and gently remove the jammed paper by pulling in the printing direction. Check for any torn pieces. Close and turn on again.

Where can I download the drivers for my printer?

Drivers are available on the Sony technical support website. You can also find them on trusted third-party sites. Search for the model UP-DF750.

What types of paper can I use?

The UP-DF750 exclusively uses Sony-specific paper from the UPP-110S (glossy) and UPP-110HD (high definition) series. Do not use other papers.

How to solve print quality issues (bands, faded colors)?

First, clean the print head. Check that the ink ribbon is correctly installed and not expired. If the problem persists, contact after-sales service.

The printer does not turn on, what should I do?

Check the power cable and wall outlet. Make sure the power switch is set to ON. If nothing happens, the internal fuse may have blown; contact an authorized technician.

How do I replace the ink ribbon?

Open the top cover, remove the old ribbon following the arrow indicators, insert the new ribbon ensuring it clicks into place. Refer to the diagram in the manual.

Can I print from my smartphone or tablet?

No, the UP-DF750 does not have native wireless connectivity. Use a computer connected via USB or Ethernet. You can also use a third-party Wi-Fi adapter.

Where can I find the complete user manual?

The complete manual is available for free on notice-facile.com for the Sony UP-DF750 model. It contains 106 pages in French.

USER MANUAL UP-DF750 SONY

For Customer in China

Printed on recycled paper

http://www.sony.net/

Sony Corporation

Printed in Japan

CE EAC

UP-DF750

© 2008 Sony Corporation

English

Owner's Record

The model and serial numbers are located at the rear. Record these numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. ____ Serial No. ____

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

No modification of this equipment is allowed.

THIS APPARATUS MUST BE EARTHED.

To disconnect the main power, unplug the power plug.

When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit.

Do not position the ME equipment where it is difficult to unplug the power plug. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or unplug the power plug.

Symbols on the products

This symbol indicates the equipotential terminal which brings the various parts of a system to the same potential.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This symbol indicates parts that may be hot. Take caution when touching parts marked with this symbol.

This symbol indicates the manufacturer, and appears next to the manufacturer's name and address.

Refer to the operating instructions Follow the directions in the operating instructions for parts of the unit on which this mark appears.

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

For the customers in Canada

This unit has been certified according to Standard CAN/CSA-C22.2 No.60601-1.

For the customers in the U.S.A and Canada

Model UP-DF750 is Non-Patient Equipment. This unit cannot be used in the vicinity of patients.

* Patient Vicinity

When you use this product connected to 240 V single phase, be sure to connect this product to a center tapped circuit.

Important safeguards/notices for use in the medical environments

1. All the equipments connected to this unit shall be certified according to Standard IEC60601-1, IEC60950-1, IEC60065 or other IEC/ISO Standards applicable to the equipments.
2. Furthermore all configurations shall comply with the system standard IEC60601-1-1. Everybody who connects additional equipment to the signal input part or signal output part configures a medical system, and

is therefore, responsible that the system complies with the requirements of the system standard IEC60601-1-1. If in doubt, consult the qualified service personnel.

This unit cannot be used in the patient environment.

* Patient Environment.

1. Do not touch the patient simultaneously while you are contacting with this equipment.
2. For this particular equipment, all accessory equipment connected as noted above must be connected to the mains via an additional isolation transformer that conforms with the construction requirements of IEC60601-1 and provides at least Basic Insulation.
3. The leakage current could increase when connected to other equipment.
4. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause interference to other equipment. If this unit causes interference (which can be determined by unplugging the power cord from the unit), try these measures: Relocate the unit with respect to the susceptible equipment. Plug this unit and the susceptible equipment into different branch circuits.

Consult your dealer. (According to standard IEC60601-1-2 and CISPR11, Class B, Group 1)

Important EMC notices for use in medical environments

• The UP-DF750 needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in these instructions for use.
• Portable and mobile RF communications equipment, such as cellular phones, can affect the UP-DF750.

Warning

The use of accessories and cables other than those specified, with the exception of replacement parts sold by Sony

Corporation, may result in increased emissions or decreased immunity of the UP-DF750.

Guidance and manufacturer's declaration-electromagnetic emissions
The UP-DF750 is intended for use in the electromagnetic environment specified below.The customer or the user of the UP-DF750 should assure that it is used in such an environment.
Emission test Compliance Electromagnetic environment-guidance
RF emissionsCISPR 11	Group 1	The UP-DF750 uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
RF emissionsCISPR 11	Class B	The UP-DF750 is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Harmonic emissionsIEC 61000-3-2	Class A
Voltage fluctuations/flicker emissionsIEC 61000-3-3	Complies

Warning

If the UP-DF750 should be used adjacent to or stacked with other equipment, it should be observed to verify normal operation in the configuration in which it will be used.

Guidance and manufacturer's declaration - electromagnetic immunity
The UP-DF750 is intended for use in the electromagnetic environment specified below. The customer or the user of the UP-DF750 should assure that it is used in such as environment.
Immunity test	IEC 60601 test level	Compliance level	Electromagnetic environment-guidance
Electrostatic discharge (ESD)IEC 61000-4-2	±6 kV contact±8 kV air	±6 kV contact±8 kV air	Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
Electrical fast transient/burstIEC 61000-4-4	±2 kV for power supply lines±1 kV for input/output lines	±2 kV for power supply lines±1 kV for input/output lines	Mains power quality should be that of a typical commercial or hospital environment.
SurgeIEC 61000-4-5	±1 kV differential mode±2 kV common mode	±1 kV differential mode±2 kV common mode	Mains power quality should be that of a typical commercial or hospital environment.
Voltage dips, short interruptions and voltage variations on power supply input linesIEC 61000-4-11	< 5% UT(>95% dip in UT) for 0.5 cycle40% UT(60% dip in UT) for 5 cycles70% UT(30% dip in UT) for 25 cycles< 5% UT(>95% dip in UT) for 5 sec	< 5% UT(>95% dip in UT) for 0.5 cycle40% UT(60% dip in UT) for 5 cycles70% UT(30% dip in UT) for 25 cycles< 5% UT(>95% dip in UT) for 5 sec	Mains power quality should be that of a typical commercial or hospital environment. If the user of the UP-DF750 requires continued operation during power mains interruptions, it is recommended that the UP-DF750 be powered from an uninterruptible power supply or a battery.
Power frequency (50/60 Hz)magnetic fieldIEC 61000-4-8	3 A/m 3 A/m Power	frequency magnetic	fields should be at least characteristic of a typical location in a typical commercial or hospital environment.
NOTE: UT is the a.c. mains voltage prior to application of the test level.
Conducted RF	3 Vrms	3 Vrms	Portable and mobile RF communications equipment should be used no closer to any part of the UP-DF750, including cables, than the recommended separation distance calculated from the equation appliance to the frequency of the transmitter.Recommended separation distance d = 1.2
IEC 61000-4-6	150 kHz to 80 MHz
Radiated RF	3 V/m	3 V/m	d = 1.2 80 MHz to 800 MHz d = 2.3 800 MHz to 2.5 GHzWhere P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m).Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than the compliance level in each frequency range. b Interference may occur in the vicinity of equipment marked with following symbol:
IEC 61000-4-3	80 MHz to 2.5 GHz
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the UP-DF750 is used exceeds the applicable RF compliance level above, the UP-DF750 should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the UP-DF750.b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.Recommended separation distances between portable and mobile RF communications equipment and the UP-DF750
The UP-DF750 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the UP-DF750 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (Transmitters) and the UP-DF750 as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output power of transmitter W	Separation distance according to frequency of transmitter m
	150 kHz to 80 MHz d = 1.2 √P	80 MHz to 800 MHz d = 1.2 √P	800 MHz to 2.5 GHz d = 2.3 √P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8	7.3
100	12	12	23
For transmitters rated a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

Caution

When you dispose of the unit or accessories, you must obey the laws in the relative area or country and the regulations in the relative hospital.

When the unit is moved, place the unit in a horizontal position and lift it by holding corners of the bottom plate with 4 people.

Do not move the unit in a vertical position.

WARNING on power connection

Use a proper power cord for your local power supply.

1. Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere).

If you have questions on the use of the above Power Cord / Appliance Connector / Plug, please consult a qualified service personnel.

WARNING on power connection for medical use

Please use the following power supply cord.

With connectors (plug or female) and cord types other than those indicated in this table, use the power supply cord that is approved for use in your area.

	United States and Canada
Plug Type	HOSPITAL GRADE*
Cord type	Min.Type SJTMin.18 AWG
Minimum Rating for Plug and Appliance Couplers	10A/125V
Safety approval	UL Listed and CSA

*Note: Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked 'Hospital Only' or 'Hospital Grade'.

For the customers in Europe

Hereby, Sony Corporation declares that the UP-DF750/Digital Film Imager is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

For details, please access the following URL: http://www.compliance.sony.de/

This product has been manufactured by or on behalf of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters, please refer to the addresses provided in the separate service or guarantee documents.

For the State of California, USA only

Perchlorate Material - special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate Perchlorate Material: Lithium battery contains perchlorate.

For the customers in Taiwan only

Using the CD-ROM Manual

The supplied CD-ROM includes manuals for this imager (in English, French, German, Italian, Spanish, Dutch, Swedish, Portuguese, Finnish, Danish, Norwegian, Greek and Russian). The copies of these manuals are created in pdf (Portable Document Format).

Preparations

One of the following programs must be installed on your computer in order to use the operation manuals contained on the CD-ROM disc.

- Adobe Reader Version 6.0 or higher

Memo

If Adobe Reader is not installed, you can download it from the following URL: http://www.adobe.com/

Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated in the United States and/or other countries.

Reading the CD-ROM Manual

To read the manual on the CD-ROM, proceed as follows.

1. Insert the CD-ROM disc in your CD-ROM drive. The manuals are saved in the Instructions For Use folder.

2. Select and click the manual that you want to read.

Memo

The files may not be displayed properly, depending on the version of Adobe Reader. In such a case, install the latest version you can download from the URL mentioned in “Preparations” above.

Note

If you lose the CD-ROM disc or you cannot read it for some reason, you can purchase a new CD-ROM disc. Contact your nearest Sony dealer.

Specifications

Power requirements AC 100-120/200-240 V, 50/60 Hz

Input current 4.4/2.4 A

Operating temperature 10 °C to 30 °C (50 °F to 86 °F)

Operating humidity 20% to 80% (no condensation allowed)

Operating pressure 700 hPa to 1,060 hPa

Storage and transport temperature -20 °C to +60 °C (-4 °F to +140 °F)

Storage and transport humidity 20% to 80% (no condensation allowed)

Storage and transport pressure 700 hPa to 1,060 hPa

Dimensions Approx. 600 × 316 × 686 mm (w/h/d) (23 5/8 × 12 1/2 × 27 1/8 inches) (Without including projecting parts)

Mass Approx. 65 kg (143 lb 4 oz)

Printing system Thermal printing

Resolution 23.78 dot/mm (604 dpi)

Gradations 16,384 levels processing

Maximum print size 346.7 × 415.3 mm (when using the UPT-517BL)

Picture elements 8,256 × 9,888 dots (w/h) (when using the UPT-517BL)

Throughput Approx. 75 sheets/hour (excluding the time for cooling the head) (when using the UPT-517BL)

Digital interface Network port × 1 (RJ-45 Modular jack), Conforming to 1000BASE-T/100BASE-TX standard

Input connector AC IN (for power)

Accessories supplied Output tray (1) Cleaning Kit (1) Output tray stopper (1) Film tray size adapter kit (1) Before Using this Imager (1) CD-ROM (1) Service Contact List (1)

Accessories supplied separately Blue Thermal Film UPT-517BL Blue Thermal Film UPT-514BL Blue Thermal Film UPT-512BL Blue Thermal Film UPT-510BL Blue Thermal Film UPT-M712BL Blue Thermal Film UPT-M710BL Cleaning kit UPA-500

Medical Specifications

Protection against electric shock:

Class I

Protection against harmful ingress of water:

Ordinary

Degree of safety in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide:

Not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide

Mode of operation:

Continuous

Design and specifications are subject to change without notice.

Notes

- Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE TO PRINT CONTENT OF ANY TYPE OR LOSS OF DATA DUE TO FAILURE OF THIS UNIT OR ITS PRINTING MEDIA, ASSOCIATED SOFTWARE, EXTERNAL STORAGE, OR OTHER EXTERNAL DEVICE.

- SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.

• Rasterization for True Type font is based on Free Type Project software. • Z lib ©1995-2003 Jean-loup Gailly and Mark Adler
• SMPTE Test Pattern - RP133- Copyright 1983

SOP and Meta SOP Classes

SOP Class Name SOP Class UID
Verification SOP Class 1.2.840.10008.1.1
Basic Grayscale Print Management Meta SOP Class	1.2.840.10008.5.1.1.9
Basic Film Session SOP Class 1.2.840.10008.5.1.1.1
Basic Film Box SOP Class 1.2.840.10008.5.1.1.2
Basic Grayscale Image Box SOP Class	1.2.840.10008.5.1.1.4
Print SOP Class 1.2.840.10008.5.1.1.16
Basic Annotation Box SOP Class 1.2.840.10008.5.1.1.15
Presentation LUT SOP Class 1.2.840.10008.5.1.1.23

UPA-500 Cleaning Kit

The UPA-500 Cleaning Kit is designed for use with the UP-DF500/DF550/DF750.

The UPA-500 Cleaning Kit includes the following three cleaning supplies.

- Cleaning paper

Used for cleaning the thermal head.

- Lapping film

Used during periodic maintenance performed by a Sony service representative. Keep this stored safely until the periodic maintenance.

- Cleaning roller

For details on replacing the cleaning roller and cleaning the thermal head, refer to the manuals on the CD-ROM supplied with the printer.

About the Blue Thermal Film (UPT-517BL/514BL/512BL/510BL/M712BL/M710BL)

For the customers in Europe

Hereby, Sony Corporation, declares that the Blue Thermal Film (UPT-517BL/514BL/512BL/510BL/M712BL/M710BL) is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC. For details, please access the following URL :

http://www.compliance.sony.de/

This product has been manufactured by or on behalf of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.

Precautions

• Store unopened film in a cool dark place.
• Open film only when ready to use.
• Please refer to the imager's instruction manual about how to load the film.
• Promptly load the film into the tray and place into the imager.
• This film is specifically designed for Sony imagers. Do not use with imagers from other manufacturers.

Do not re-use

Doing so may result in malfunction and negatively affect printing results.

WARNING

THIS APPARATUS MUST BE EARTHED.

- Adobe Reader Version 6.0 or later

N.B.:

Verification SOP Class 1.2.840.10008.1.1

Basic Grayscale Print Management Meta	1.2.840.10008.5.1.1.9
SOP Class

Sony Corporation hereby declares that the UP-DF750 Digital

SOP Class Name SOP Class UID

Verification SOP Class 1.2.840.10008.1.1

Basic Grayscale Print Management Meta 1.2.840.10008.5.1.1.9SOP Class

Basic Film Session SOP Class 1.2.840.10008.5.1.1.1

SOP Class Name SOP Class UID
Basic Film Box SOP Class 1.2.840.10008.5.1.1.2
Basic Grayscale Image Box SOP Class	1.2.840.10008.5.1.1.4
Print SOP Class 1.2.840.10008.5.1.1.16
Basic Annotation Box SOP Class 1.2.840.10008.5.1.1.15
Presentation LUT SOP Class	1.2.840.10008.5.1.1.23