HDM1037 - Drill Ferm - Free user manual and instructions

Product type	Corded drill
Brand	Ferm
Model	HDM1037
Power supply	220-240 V ~ 50 Hz
Power consumption	650 W
No-load speed	0-2800 rpm
Chuck	Keyless, capacity 1.5-13 mm
Max. drilling diameter (wood)	25 mm
Max. drilling diameter (steel)	10 mm
Max. drilling diameter (concrete)	12 mm
Weight	1.5 kg
Cable length	2 m
Sound pressure level	82 dB(A)
Sound power level	93 dB(A)
Vibration (drilling metal)	2.5 m/s²
Main functions	Drilling, screwdriving, hammer
Rotation direction	Left/right
Variable speed	Yes, by trigger
Spindle lock	Yes
Auxiliary handle	Yes, removable
Included equipment	Chuck, screwdriver bit, hex key
Maintenance and cleaning	Unplug before cleaning. Clean with a dry cloth, without solvents.
Safety	Wear hearing and eye protection. Do not use in presence of flammable vapors.
Spare parts	Available from Ferm customer service or authorized dealers.
Warranty	2 years (subject to general conditions)

Frequently Asked Questions - HDM1037 Ferm

How to change the chuck of the Ferm HDM1037 drill?

To change the chuck, first unplug the tool. Use the supplied hex key to loosen the fixing screw (located inside the chuck). Turn the chuck counterclockwise to remove it. To install a new chuck, screw it on by hand, then tighten the fixing screw.

What is the power of the Ferm HDM1037 drill?

The Ferm HDM1037 drill has a power consumption of 650 W, allowing it to drill effectively in wood, steel and concrete.

How to adjust the speed of the drill?

The speed is progressively adjustable by pressing the trigger more or less. A light press gives low speed, a stronger press increases the speed. A rotation direction selector (left/right) is also present.

Can I use the drill for screwdriving?

Yes, the Ferm HDM1037 drill has a screwdriving function. Simply reduce the speed and use a suitable screwdriver bit. The hammer function must be deactivated for screwdriving.

How to activate the hammer function?

The hammer function is activated by turning the mode selector located above the chuck to the hammer position (hammer symbol). This function is reserved for drilling in masonry.

What maximum drilling diameter can I achieve?

The recommended maximum diameters are: 25 mm in wood, 10 mm in steel and 12 mm in concrete. For larger diameters, use a suitable drill bit and reduce the speed.

How to clean the drill after use?

Always unplug the tool. Clean the housing with a dry cloth or slightly damp cloth. Do not use solvents or abrasive products. The ventilation slots can be dusted with compressed air.

What to do if the chuck jams?

If the chuck jams, first make sure the tool is unplugged. Try to loosen manually by holding the clamping ring. If that does not work, use an adjustable spanner while protecting the chuck with a cloth. Avoid excessive force.

Where to find spare parts for the Ferm HDM1037?

Spare parts (brushes, chuck, etc.) are available from Ferm customer service or authorized dealers. Visit the Ferm website for the list of service centers.

What are the essential safety precautions?

Always wear safety glasses and hearing protection. Use the auxiliary handle for better control. Ensure the work area is clear and that you do not damage hidden electrical cables. Unplug the tool before changing an accessory.

USER MANUAL HDM1037 Ferm

Blue FERM drill put tool with black handle and blade, shown against black background (no text or symbols on device body)

HDM1037

EN Original instructions 04
DE Übersetzung der Originalbetriebsanleitung 08
NL Vertaling van de oorspronkelijke gebruiksaanwijzing 13
FR Traduction de la notice originale 18
ES Traducción del manual original 23
PT Tradução do manual original 28
IT Traduzione delle istruzioni originali 33
SV Översättning av bruksanvisning i original 38
FI Alkuperäisten ohjeiden käännös 42
NO Oversatt fra orginal veiledning 46
DA Oversættelse af den originale brugsanvisning 50

HU Eredeti használati utasítás fordítása 54
CS Překlad původního návodu k používání 58
SK Prevod izvirnih navodil 62
PL Tłumaczenie instrukcji oryginalnej 66
LT Originalios instrukcijos vertimas 70
LV Instrukciju tulkojums no originālvalodas 74
RO Traducere a instructiunilor originale 78
RU Перевод исходных инструкций 82
EL Μετάφραση του πρωτοτύπου των οδηγιών χρήσης 87

CE

Fig. A

Fig. B

Fig. C

Fig. D

T

A

C

-

B

D
Fig. E

ROTARY HAMMER DRILL

Thank you for buying this FERM product. By doing so you now have an excellent product, delivered by one of Europe's leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.

1.SAFETYWARNINGS

WARNING

Read the enclosed safety warnings, the additional safety warnings and

the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

Read the user manual.

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Risk of electric shock

Immediately remove the mains plug from the mains if the mains cable becomes damaged and during cleaning and maintenance.

Always wear eye protection!

Wear hearing protection.

Wear safety gloves.

Do not dispose of the product in unsuitable containers.

The product is in accordance with the applicable safety standards in the European directives.

Additional safety warnings for rotary hammers

a) Wear ear protectors. Exposure to noise can cause hearing loss.

b) Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

c) Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

Electrical safety

When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the voltage of the power supply corresponds to the voltage on the rating plate label.

Class II machine - Double insulation - You don't need any earthed plug.

If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Replacement of power cords or plugs

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is damaged and needs replacing, it is important that it is correctly destroyed and replaced by an approved BS1363/13A fused plug and that the following wiring instructions are followed.

The wires in the mains cable are coloured in accordance with the following code:

• blueneutral
  •brownlive

As the colours of the wires in the mains cable of the unit may not correspond to the coloured markings identifying the terminals in the plug, proceed as follows:

• The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

Use of extension leads

Only ever use approved extension leads that are suitable for the power rating of the machine. The minimum core thickness is 1.5 mm^2 . Whenever using a reel extension lead, always fully unroll the lead.

Immediately switch off the machine when:

• Excessive sparking of the carbon brushes.
• Interruption of the mains plug, mains lead or mains lead damage.
• Defectswitch.
• Smoke or stench of scorched isolation.

2. MACHINE INFORMATION

Intended use

This rotary hammer is intended for drilling holes in masonry such as brick, concrete and similar material. Furthermore, the machine can be used as a demolition hammer in combination with the SDS cold chisels provided. The machine is on no account intended for other purposes.

Not suitable for construction site usage

Technical specifications

Mains voltage 230 V ~
Mains frequency 50 Hz
Power input 1500 W
No-load speed 0-950 /min
Impact rate 0-4400 /min
Max. Drill diameter
-Concrete	32 mm
-Steel	13 mm
-Wood	42 mm

Weight 5.2 kg

Sound pressure (L _PA ) 92.7dB(A) K=3 dB(A)
Acoustic power (L _WA )	103.7dB(A) K=3 dB(A)
Vibration
Hammer drilling concrete a _h'HD	17.360m/s ^2 K=1.5m/s ^2
Chiseling a _h,Cheq	13.334 m/s ^2 K=1.5m/s ^2

Vibration level

The vibration emission level stated in this instruction manual has been measured in accordance with a standardized test given in EN60745. It may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned.

• Using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level.
• The times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level.

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm and organizing your work patterns.

Description

The numbers in the text refer to the diagrams on pages 2-3

Fig. A

1. On/off switch
2. Drill selection switch
3. Hammer selection lever

4.Chuck
5.Lockingsleeve
6.Maingrip
7.Auxiliarygrip
9. Lubricationpoint
10. Adjusting wheel for electronic speed control

3. ASSEMBLY

Before assembly, always switch off the machine and remove the mains plug from the mains.

Mounting and removing the accessory

Fig. B

Do not use blunt drill bits or chisels. Immediately sharpen or replace blunt drill bits or chisels.

Mounting

• Apply a few drops of oil to the shaft of the accessory.
• Slide the locking sleeve (5) to the rear.
• Insert the accessory into the chuck (4).
• Secure the accessory by turning it counterclockwise until it locks into place.
• Release the locking sleeve (5).

Removing

• Slide the locking sleeve (5) to the rear.
• Remove the accessory from the chuck (4).
• Release the locking sleeve (5).

Mounting and removing the auxiliary grip Fig. C

Mounting

• Loosen the auxiliary grip (7) by turning it counterclockwise.
• Mount the auxiliary grip (7) by sliding it over the chuck (4).
• Turn the auxiliary grip (7) to the required position.
• Tighten the auxiliary grip (7) by turning it clockwise.

Removing

• Loosen the auxiliary grip (7) by turning it counterclockwise.
• Remove the auxiliary grip (7).
• Tighten the auxiliary grip (7) by turning it clockwise.

Mounting and removing the dust collector

Fig. D

The dust collector prevents dust from entering the machine when drilling into ceilings.

Immediately replace a damaged dust collector.

Mounting

• If necessary, remove the accessory from the chuck (4).
• Slide the dust collector (15) over the shaft of the accessory.
• Insert the accessory with the dust collector (15) into the chuck (4).

Removing

• Remove the accessory with the dust collector (15) from the chuck (4).
• Remove the dust collector (15) from the accessory.

4. USE

Switching on and off

Fig. A

• To switch on the machine, press the on/off switch (1).
• To switch off the machine, release the on/off switch (1).

Speed Preselection (10)

The required speed can be preselected with the thumbwheel. Also during running the rotational speed can be adjusted.

1 - 2 = low speed

3 - 4 = medium speed

5 - 6 = high speed

Max = maximum speed

The required speeds depends on the material and can be determined by practical testing.

Setting the operating mode

Fig. A & E

The drill selection switch and the hammer selection lever must be set according to the required operating mode. Refer to the table below to set the required operating mode.

Setting Operating mode

Fig. E

A Chisel

BHammerdrill

CDrill

D Chisel angle adjustment

- Turn the drill selection switch (2) and the hammer selection lever (3) to the required position.

Hints for optimum use

• Clamp the workpiece. Use a clamping device for small workpieces.
• Firmly hold the machine by the grip.
• Set the operating mode.
• Switch on the machine.
• Do not apply too much pressure on the machine. Let the machine do the work.
• Switch off the machine and wait for the machine to come to a complete standstill before putting the machine down.

5. CLEANING AND MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.

Clean the machine casings regularly with a soft cloth, preferably after each use. Make sure that the ventilation openings are free of dust and dirt. Remove very persistent dirt using a soft cloth moistened with soapsuds. Do not use any solvents such as gasoline, alcohol, ammonia etc. Chemicals such as these will damage the synthetic components.

Defects

The machine should be regularly inspected for the following possible defects and repaired if necessary.

• Damage to power cord.
- Broken on/off trigger assembly.
- Shortcircuiting.
- Damaged moving parts.

Faults

Should a fault occur, e.g. after wear of a part, please contact your seller or the service address on the warranty card. Separate you find an exploded view showing the parts that can be ordered.

WARRANTY

The warranty conditions can be found on the separately enclosed warranty card.

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

The product and the user manual are subject to change. Specifications can be changed without further notice.

BOHRHAMMER

ROTERANDE HAMMARBORR

1 - 2 = niskie obroty

CE

DECLARATION OF CONFORMITY HDM1037 - ROTARY HAMMER

(EN) We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 9 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt der Direktive 2011/65/EU des Europäischen Parlaments und des Rats vom 9 Juni 2011 über die Einschränkung der Anwendung von bestimmten gefährlichen Stoffen in elektrischen und elektronischen Geräten entspricht. den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijkheid dat dit product voldoet aan de conform Richtlijn 2011/65/EU van het Europees Parlement en de Raad van 8 juni 2011 betreffende beperking van het gebruik van bepaalde gevaarlijke stoffen in elektrische en elektronische apparatuur en in overeenstem ming is met de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants: est conforme à la Directive 2011/65/EU du Parlement Européen et du Conseil du 8 juin 2011 concernant la limitation d'usage de certaines substances dangereuses dans l'équipement électrique et électronique.
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento: se encuentra conforme con la Directiva 2011/65/UE del Parlamento Europeo y del Consejo de 8 de junio de 2011 sobre la restricción del uso de determinadas sustancias peligrosas en los equipos eléctricos y electrónicos.
(PT) Declaramos por nossa total responsabilidade de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem: está em conformidade com a Directiva 2011/65/EU do Parlamento Europeu e com o Conselho de 8 de Junho de 2011 no que respeita à restrição de utilização de determinadas substâncias perigosas existentes em equipamento eléctrico e electrónico.
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti: è conforme alla Direttiva 2011/65/UE del Parlamento Europeo e del Consiglio dell'8 giugno 2011 sulla limitazione dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche.
(SV) Vi garanterar på eget ansvar att denna produkt uppfyller och följer följande standarder och bestämmelser: uppfyller direktiv 2011/65/EU från Europeiska parlamentet och EG-rådet från 8 juni 2011 om begränsningen av användning av farliga substanser i elektrisk och elektronisk utrustning.
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset: täyttää Euroopan parlamentin ja neuvoston 8. kesäkuuta 2011 päivätyn direktiivin 2011/65/EU vaatimukset koskien vaarallisten aineiden käytön rajoitusta sähkö- ja elektronisissa laitteissa.
(NO) Vi erklærer under vårt eget ansvar at dette produkteter i samsvar med følgende standarder og regler: er i samsvar med EU-direktivet 2011/65/EU fra Europa-parlamentet og Europa-rådet, pr. 8 juni 2011, om begrensning i bruken av visse farlige stoffer i elektrisk og elektronisk utstyr.
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser: er i overensstemmelse med direktiv 2011/65/EU fra Europa-Parlamentet og Rådet af 8. juni 2011 om begrænsning af anvendelsen af visse farlige stoffer i elektrisk og elektronisk udstyr.
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak: je v souladu se směrnici 2011/65/EU Evropského parlamentu a Rady EU ze dne 8. června 2011, která se týká omezení použití určitých nebezpečných látek v elektrických a elektronických zařízeních.

(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami: Je v súlade s normou 2011/65/EÚ Európskeho parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronickom vybavení.
(SK) Výhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcími normami a predpismi: Je v súlade s normou 2011/65/EÚ Európske ho parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronikom vybavení.
(SL) S polno odgovomostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom: je v skladu z direktivo 2011/65/EU Evropskega parlamenta in Sveta z dne 8. junij 2011 o omejevanju uporabe določenih nevarnih snovi v električni in elektronski opremi.
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach; jest zgodny z Dyrektywą 2011/65/UE Parła mentu Europejskiego i Rady z dnia 8 czerwca 2011 r. w sprawie ograniczenia stosowania niektórych niebezpiecznych substancji w sprzęcie elektrycznym i elektronicznym.
(LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau paminėtus standartus arba nuostatus: atitinka 2011 m. birželio 8 d. Europos Parlamento ir Tarybos direktyvą 2011/65/EB dėl tam tikrų pavojingų medžiagų naudojimo elektros ir elektroninėje įrangoje apribojimo.
(LV) Ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās.
(ET) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem: ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās.
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive: este în conformitate cu Directiva 2011/65/UE a Parlamentului European și a Consiliului din 8 iunie 2011 cu privire la interzicerea utilizării anumitor substanțe periculoase la echipamentele electrice și electronice.
(HR) Izjavljujemo pod vlastitom odgovornoLsu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama: usklađeno s Direktiv 2011/65/EU europskog parlamenta i vijeća izdanom 8. lipnja 2011. o ograničenju korištenja određenih opasnih tvari u električnoj i elektroničkoj opremi.
(SRL) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama: usaglašen sa direktivom 2011/65/EU Evropskog parlamenta i Saveta od 8.juna.2011. godine za restrikciju upotrebe određenih opasnih materija u električnoj i elektronskoj opremi.
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам: соответствует требованиям Директивы 2011/65/EU Европейского парламента и совета от 8 июня 2011 г. по ограничению использования определенных опасных веществ в электрическом и электронном оборудовании
(UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає наступним стандартам і нормативам: задовольняєв вимоги Директиви 2011/65/ЄС Європейського Парламенту та Ради від 8 червня 2011 року на обмеження використання деяких небезпечних речовин в електричному та електронному обладнанні.
(EL) Δηλώνουμε υπεύθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτυ κανονισμούς και πρότυπα: συμμοφώνεται με την Οδηγία 2011/65/ΕΕ του Ευρωπαϊκού Κοινοβουλιου και του Συμβουλιου της Νςς Ιουνίου 2011 για τον περιορισμό της χρήσης ορισμένων επικίνδυνων υσιών σε ηλεκτρικό και ηλεκτρονικό εξοπλισμό.

EN 60745-1, EN 60745-2-6, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3

2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EC

Zwolle, 01-03-2019

FERM - Lingenstraat 6 - 8028 PM - Zwolle - The Netherlands