Q: How to lower the temperature of the refrigerator on the model ERAVE180-90V2?

On the ESSENTIELB ERAVE180-90V2, it is the B button that controls the temperature of the refrigerator compartment. This button allows you to set between 2°C and 8°C , or completely deactivate the compartment in the "OFF" position. If you notice that pressing increases the temperature instead of decreasing it, you are acting in the wrong direction . Make sure to check the direction of button B - you need to press in the opposite direction to lower the temperature. The manufacturer's recommended setting is 3°C to start . If the OK indicator does not appear, set it to 2°C (the minimum temperature). Note that the actual temperature also varies depending on the amount of food stored and the ambient temperature of your kitchen. If you want very fast cooling, you can also activate the SUPER COOLING mode, which will run the compartment at its lowest temperature for about 2 hours.

Q: How to reset the ESSENTIELB Easy WiFi AC 750 WiFi repeater?

To reset the ESSENTIELB Easy WiFi AC 750: Locate the Reset button (a small recessed hole located at the back, bottom, or side of the repeater) Using a paperclip or a sharp pointed object , press and hold the Reset button for about 10 seconds The LED indicators will blink to indicate the restart The device will reset to factory settings After the reset: The SSIDs will revert to easywifi_AC750_2.4G_XXXXXX and easywifi_AC750_5G_XXXXXX with the default password 12345678 . You will then need to reconfigure the repeater by connecting it to your main Wi-Fi network (see the question "How to connect the WiFi repeater..." for detailed steps).

Q: What is the capacity in liters of the bowl of the ESSENTIELB EBM10 robot?

The bowl of the ESSENTIELB EBM10 robot has a capacity of 1.5 liters . This size is suitable for preparing mixtures, doughs, or other culinary preparations in quantities sufficient for a family or regular household use.

Question 1

What are the default credentials (username and password) to access the configuration page of the ESSENTIELB Easy WiFi AC 750 WiFi repeater?

Accepted Answer

To access the configuration page of the ESSENTIELB Easy WiFi AC 750 WiFi repeater, use the following default credentials:

Username: admin
Password: 12345678

You can access the configuration interface via one of these addresses:

URL: http://easywifi.config
Alternative IP address: 192.168.1.200

For security reasons, it is recommended to change the default password after the first configuration of the repeater.

Question 2

How to lower the temperature of the refrigerator on the model ERAVE180-90V2?

Accepted Answer

On the ESSENTIELB ERAVE180-90V2, it is the B button that controls the temperature of the refrigerator compartment. This button allows you to set between 2°C and 8°C, or completely deactivate the compartment in the "OFF" position.

If you notice that pressing increases the temperature instead of decreasing it, you are acting in the wrong direction. Make sure to check the direction of button B - you need to press in the opposite direction to lower the temperature.

The manufacturer's recommended setting is 3°C to start. If the OK indicator does not appear, set it to 2°C (the minimum temperature). Note that the actual temperature also varies depending on the amount of food stored and the ambient temperature of your kitchen.

If you want very fast cooling, you can also activate the SUPER COOLING mode, which will run the compartment at its lowest temperature for about 2 hours.

Question 3

How to connect the ESSENTIELB Easy WiFi AC 750 repeater to your network?

Accepted Answer

To connect your ESSENTIELB Easy WiFi AC 750 repeater to your network, follow these steps:

Method 1: Via the web interface (recommended)

Connect to the WiFi network of the repeater (SSID: easywifi_AC750_2.4G_XXXXXX or easywifi_AC750_5G_XXXXXX).
Open your browser and go to http://easywifi.config (or 192.168.1.200).
Log in with the username admin and the default password 12345678.
Select the Repeater mode in the setup wizard.
Click on Start Scan to display the available WiFi networks.
Choose your main WiFi network (the one from your internet box). Ensure that the signal is above 60% for optimal speed.
Enter the security key of your network, then click Next.

Method 2: Via WPS (faster)

Press the WPS button on your internet box, then within the next 2 minutes, press the WPS button on the repeater. The connection will be established automatically.

Once connected, the repeater will broadcast the WiFi signal of your main network over an extended range.

Question 4

Where is the reset button on the ESSENTIELB Easy WiFi AC 750 repeater?

Accepted Answer

The reset button on the ESSENTIELB Easy WiFi AC 750 repeater is a small recessed hole that needs to be held down for about 10 seconds using a paperclip to reset the device to its default settings.

Although the manual does not specify the exact location of the button on the casing (back, bottom, or side), here’s how to locate it:

Look for a small hole or recessed cavity (very small diameter)
It may be located at the back, on the bottom, or on a side of the device
Check for an inscription “Reset” or a symbol nearby
Use a paperclip or a thin pin to press the button (never force it)

During the reset, the LED indicators will blink and the device will restart. The default settings will be restored (SSID: easywifi_AC750_2.4G_XXXXXX and easywifi_AC750_5G_XXXXXX, password: 12345678).

If you cannot find the physical button, you can also perform a reset via the web interface by connecting to the IP address 192.168.1.200 after connecting to the repeater's network.

Question 5

How to reset the ESSENTIELB Easy WiFi AC 750 WiFi repeater?

Accepted Answer

To reset the ESSENTIELB Easy WiFi AC 750:

Locate the Reset button (a small recessed hole located at the back, bottom, or side of the repeater)
Using a paperclip or a sharp pointed object, press and hold the Reset button for about 10 seconds
The LED indicators will blink to indicate the restart
The device will reset to factory settings

After the reset: The SSIDs will revert to easywifi_AC750_2.4G_XXXXXX and easywifi_AC750_5G_XXXXXX with the default password 12345678. You will then need to reconfigure the repeater by connecting it to your main Wi-Fi network (see the question "How to connect the WiFi repeater..." for detailed steps).

Question 6

How do I set the freezer thermostat on the Essentielb ERCVE190-60B1 refrigerator?

Accepted Answer

The thermostat for the freezer of the Essentielb ERCVE190-60B1 is located inside the freezing compartment and offers 3 adjustment positions:

NORMAL - Standard and daily use (default position)
COLD - Colder temperature, recommended when the ambient temperature exceeds 35 °C (especially in summer)
COLDER - The coldest temperature, recommended when the ambient temperature is below 10 °C (especially in winter)

The setting is mainly adjusted according to seasonal conditions and the temperature of your environment. Start with the NORMAL position and adjust to COLD or COLDER as needed for cooling.

Question 7

Why is the refrigerator section of my ESSENTIELB ERAVE180-90V2 freezing food?

Accepted Answer

If your ESSENTIELB ERAVE180-90V2 is freezing food in the refrigerator compartment, it is almost always due to a temperature set too low. Your refrigerator offers a temperature range of 2°C to 8°C for the refrigerator compartment (button B). The recommended setting is 3°C. If food is freezing, immediately adjust the button to a higher temperature, for example 4°C or 5°C, and wait a few hours to see if there is an improvement.

Check that you have not accidentally activated the SUPER COOLING mode by pressing button C. This special mode operates the refrigerator at its lowest temperature for about 2 hours to quickly cool food. At the end of this period, the temperature automatically returns to the previous setting. If this mode is activated (you will see it on the display), select another mode: SMART, ECO, or USER SETTINGS.

Ensure that the air circulation inside the refrigerator is not blocked. Overcrowded or poorly arranged food can create excessively cold spots, especially if you place items directly against the back wall or bottom of the compartment. Organize your food to leave free space around them to allow fresh air to circulate.

Limit the prolonged opening of the refrigerator door. Leaving the door open for a long time causes a significant increase in temperature inside, which forces the cooling system to compensate by overcooling. Keep the door closed unless necessary and only leave it open for a few seconds.

Avoid placing a large amount of hot food in the appliance within the last 24 hours. This forces the compressor to work hard and can create excessively cold spots. If you have recently stored a lot of food, wait a few hours and check the temperature again.

Also, check that your refrigerator is not installed near a heat source (radiator, stove, direct sunlight) or in a poorly ventilated area. A too warm environment forces the appliance to cool more. Ensure there is good air circulation around the refrigerator and that it does not touch walls or other objects.

Question 8

What is the capacity in liters of the bowl of the ESSENTIELB EBM10 robot?

Accepted Answer

The bowl of the ESSENTIELB EBM10 robot has a capacity of 1.5 liters. This size is suitable for preparing mixtures, doughs, or other culinary preparations in quantities sufficient for a family or regular household use.

Question 9

What does the flashing temperature indicator on the ESSENTIELB ESLHP8-2B radiator mean and how can I resolve this issue?

Accepted Answer

The flashing temperature indicator on your ESSENTIELB ESLHP8-2B radiator generally indicates a malfunction related to the device's temperature. Here are the possible causes and solutions to consider:

Possible Causes

Overheating of the device: The radiator detects an internal temperature that is too high.
Inadequate ambient temperature: The device is placed in an environment that is too hot or poorly ventilated.
Blocked filters or grilles: Dust or debris obstructs air circulation, which can lead to overheating.
Technical defect: An internal issue may trigger a temperature alert.

Solutions to Try

Check the location: Ensure that the radiator is placed in a well-ventilated area, away from direct heat sources.
Clean the filters and grilles: Remove accumulated dust from the filters and air grilles to ensure proper air circulation.
Restart the device: Turn off the radiator, wait about 5 minutes, then turn it back on to reset the system.
Check the settings: Ensure that the set temperature is appropriate and does not cause overheating.

If the indicator continues to flash after these checks, it is advisable to have the device inspected by a professional or the after-sales service to avoid any risk of damage or safety issues.

Question 10

How to exit demo mode on the ESSENTIELB ESLHP8-2B dryer?

Accepted Answer

Your ESSENTIELB ESLHP8-2B is a heat pump dryer, not a washing machine. According to the official manual available, this model does not have a documented demo mode function. The dryer operates in standard mode: once you select a program using the program selection button and press the Start/Pause button, the drying cycle starts immediately to dry your laundry.

If your appliance does not start the drying cycles normally after powering on, check that the loading door is properly closed and that a program is correctly selected before pressing Start/Pause. Also, check that the child lock is not activated (it locks the buttons): to deactivate it, press and hold the Ringtone/Timer and Drying Level buttons simultaneously for 3 seconds.

If you encounter operational difficulties, refer to the troubleshooting guide in the manual or contact the SOURCING & CREATION customer service.

User manual ESSENTIELB : user manuals and guides in PDF

Models ESSENTIELB most viewed

Browse manuals ESSENTIELB by appliance type

Recent questions about devices ESSENTIELB