Question 1

What is the charging time of the battery of the GIGASET GLX 8?

Accepted Answer

The technical manual of the GIGASET GLX 8 does not specify an exact charging time in hours or minutes. However, based on the technical specifications of the product, it is possible to estimate this duration.

Your phone is equipped with a 2500 mAh Li-Polymer battery and charges via a USB-C cable with the provided adapter rated at 5 V - 1.0 A (5 W). With this configuration, the full charging time is estimated to be around 2.5 to 3.5 hours.

Important recommendations for charging:

Allowed temperature: between 0 and 45 °C during charging. Avoid environments that are too cold or too hot.
Do not charge for more than 12 consecutive hours to preserve battery health.
Charge only indoors and do not use the phone while charging.
Use only the original Gigaset adapter or a compatible approved adapter.

To extend the life of your battery, keep it between 15 and 35 °C at rest and avoid leaving it at 100% charge for long periods. Also, disable unnecessary wireless connections (Bluetooth, Wi-Fi) when you do not need them, as they consume more energy and prolong the charging time.

Question 2

How do I turn off the GIGASET PA530 Audio Plus baby monitor?

Accepted Answer

To turn off the GIGASET PA530 Audio Plus baby monitor, follow these simple steps:

Locate the power button, which is usually found on the side or underneath the parent unit or baby unit.
Press and hold this button for a few seconds until the device turns off.
Check that the indicator lights go out, confirming that the baby monitor is indeed powered off.

Properly turning off the baby monitor helps save battery and prevents any unnecessary sound or transmission.

Question 3

How to disable the earpiece on the GIGASET GLX 8?

Accepted Answer

To disable the earpiece on your GIGASET GLX 8 during a call, press the speaker icon displayed on the screen. This switches the audio output from the earpiece (handset) to the device's built-in speaker. Press this icon again to return to the earpiece.

To adjust the volume of the earpiece or the speaker, use the side key on your phone. This key controls the volume level depending on the usage mode (call, ringtone, or selected profile).

If you want to disable the earpiece permanently or adjust advanced audio settings, go to your phone's Settings, then look for sound or audio options. In this menu, you can configure your default audio output preferences, including using the speaker for all calls.

Note that you also have the option to connect wireless headphones via Bluetooth (the GLX 8 supports Bluetooth 5.0), which gives you a discreet alternative to the built-in earpiece. You can pair your Bluetooth headphones by going to the Settings menu and selecting the Bluetooth option.

Question 4

How to disable the automatic callback on a GIGASET SL910 cordless phone?

Accepted Answer

To disable the automatic callback on your GIGASET SL910 cordless phone, follow the steps below:

Access the main menu: Press the Menu button on your handset.
Open the settings: Use the arrows to navigate to Settings or Preferences and confirm with the OK button.
Find the option related to callbacks: Look for a section like Ringtones, Alerts, or Callback.
Disable the automatic callback: Select the Automatic Callback or Callback option and choose Disabled or Off.
Confirm and exit: Confirm your choice and exit the menu. The automatic callback will now be disabled.

This feature allows you to stop automatic alerts for unanswered call callbacks, which can be useful if you do not wish to be disturbed by these notifications.

Question 5

Why does my GIGASET DL500A cordless phone not emit any signal and how can I resolve this issue?

Accepted Answer

If your GIGASET DL500A cordless phone is not emitting any signal, several causes may be responsible for this malfunction. Here are the steps to follow to identify and resolve the issue:

1. Check the base connections

Ensure that the phone base is properly plugged into a functional power outlet.
Check that the telephone cable is properly connected to the wall socket and the base.

2. Check the handset registration

The handset must be registered to the base to function. If it is not, it will not be able to emit a signal.
Proceed with a new registration of the handset to the base according to the specific procedure for the GIGASET DL500A.

3. Test the telephone line

Plug another phone into the same socket to check that the line is functioning correctly.
If the other phone does not work either, the problem is likely with the telephone line.

4. Check the handset battery

Ensure that the battery is properly installed and sufficiently charged.
A weak or defective battery may prevent the handset from emitting a signal.

5. Eliminate interference

Keep the phone and its base away from other electronic devices that may cause interference (microwaves, Wi-Fi routers, etc.).

6. Reset the phone

As a last resort, perform a factory reset of the phone.
Note that this operation will erase saved data, so be sure to back up your contacts if possible.

By following these steps, you should be able to identify the cause of the problem and restore the normal functioning of your GIGASET DL500A phone.

Question 6

How to unlock a GIGASET SL930A phone when the lock code is forgotten?

Accepted Answer

If you have forgotten the lock code (system PIN) of your GIGASET SL930A base, you can reset it to the factory value 0000 by following the procedure below. Note: this operation will reset all the settings of the base and all registered handsets will need to be re-registered.

System PIN code reset procedure:

Unplug the power cord from the GIGASET SL930A base.
Press and hold the registration/paging button located on the base.
Reconnect the power cord to the electrical outlet while holding the button down.
Continue to hold the button for about 10 seconds after plugging it in.
Release the button. The base will restart and the PIN code will be reset to 0000.

After the reset:

All custom settings and configurations of the base are deleted.
Each registered handset must be re-registered on the base. Refer to your handset's manual for the exact registration procedure.
You can now access the base with the default PIN code 0000.
It is recommended to change this PIN code to a memorized custom code to avoid having to reset it again in the future.

Important: If you prefer not to reset the base and lose your settings, contact GIGASET technical support at 01 57 32 45 22 (Monday-Saturday 8am-8pm) or via the contact form on www.gigaset.com/contact for assistance specific to your situation.

Question 7

How to disable the silent mode on a GIGASET SL910 cordless phone?

Accepted Answer

To disable the silent mode on your GIGASET SL910 cordless phone, follow the steps below:

Access the main menu: Press the Menu button on your phone.
Open settings: Use the navigation arrows to select Settings, then press OK.
Access sound options: In the settings menu, choose Sound.
Disable silent mode: Look for the Silent mode option and select it. You will then be able to choose to disable this mode.

Once these steps are completed, the silent mode will be disabled and your phone will emit the usual sounds during calls or other notifications.

If you cannot find this option or if the menus differ, please refer to the official user manual for your GIGASET SL910, available on the manufacturer's website or on online manual platforms.

User manual GIGASET : user manuals and guides in PDF

Models GIGASET most viewed

Browse manuals GIGASET by appliance type

Recent questions about devices GIGASET