Q: How to bake a ciambella with the ARIETE Bon Cuisine 450 0986 oven?

Parameters for the ciambella: Temperature: 170°C (use the thermostat knob) Cooking mode: Combined heating (top + bottom) for even cooking Time: 10-15 minutes depending on size Positioning: Place the ciambella on a baking tray in the center of the oven, at least 2 cm from the top heating elements Procedure: Select the Combined heating mode (top and bottom heating) Turn the thermostat knob to 170°C Place the ciambella in the oven Set the rotary timer for 10-15 minutes The indicator light will turn on and off once the temperature is reached At the end of the time, check that the surface is golden Important tip: Never cover the inside of the oven with aluminum foil, as this could damage the thermostat. Use a regular baking tray.

Q: How do I open the bottom of the oven for cleaning?

First of all: wait for the oven to cool completely before accessing the lower part. Procedure to access the crumb tray: Turn the oven over using the specially designed knob for this purpose (Fig. 4) Open the drawer by lifting it slightly upwards first (Fig. 5) This gives you access to the crumb tray (E) , the lower compartment that collects food residues. Cleaning: Clean it with a damp sponge and remove any food, crumbs, or residues. This operation should be performed after each use for optimal operation of your oven.

Question 1

Why is the nozzle of my ARIETE 1329 coffee maker spraying everywhere?

Accepted Answer

The spraying issue with your ARIETE 1329 nozzle is generally caused by clogging or an overload of coffee. Here’s how to resolve it:

Cleaning the Thermocream® nozzle

Unclog the nozzle with a fine pin - The outlet may be blocked by coffee residues or accumulated limescale
Let the steam escape for a few seconds after each use to prevent residues from building up

Check the filter and coffee dose

Reduce the coffee dose - Do not exceed 50 ml per coffee (maximum dose). An overload prevents the filter from sealing correctly and causes overflow or splashing
The Thermocream® filter can become clogged with greasy residues or limescale after a few months of use, disrupting the uniform flow of water and causing splashes

Recommended maintenance

Use COFFEE CLEAN tablets every 3 months to thoroughly clean the filter (refer to the product instructions)
Regularly clean the internal openings of the filter with a small soft brush
Ensure that the seal between the filter and the nozzle is correct by checking for any coffee residues

If the problem persists after these interventions, it is possible that the Thermocream® filter is damaged or that the nozzle requires professional cleaning from an authorized ARIETE service.

Question 2

How to bake a ciambella with the ARIETE Bon Cuisine 450 0986 oven?

Accepted Answer

Parameters for the ciambella:

Temperature: 170°C (use the thermostat knob)
Cooking mode: Combined heating (top + bottom) for even cooking
Time: 10-15 minutes depending on size
Positioning: Place the ciambella on a baking tray in the center of the oven, at least 2 cm from the top heating elements

Procedure:

Select the Combined heating mode (top and bottom heating)
Turn the thermostat knob to 170°C
Place the ciambella in the oven
Set the rotary timer for 10-15 minutes
The indicator light will turn on and off once the temperature is reached
At the end of the time, check that the surface is golden

Important tip: Never cover the inside of the oven with aluminum foil, as this could damage the thermostat. Use a regular baking tray.

Question 3

Why does the rotating brush continue to turn while charging the ARIETE Evolution 2.0 2712 vacuum cleaner?

Accepted Answer

According to the manual for the ARIETE Evolution 2.0 2712, the brushes should not turn during charging. During charging, the screen displays "1111" (repeating from right to left) and the side brushes should remain stationary.

If a rotating brush continues to turn constantly during charging:

Check that the charging cable is properly inserted into the socket (Y) of the robot or that the charging poles (S) are correctly aligned with the contacts (G) of the base
Ensure that no debris or dust is blocking the affected brush - stop charging and clean the rotating areas
Wait a few minutes and try a full recharge again to see if the behavior persists

This abnormal behavior may indicate a fault in the charging circuit or a motor issue. If the brush continues to turn after these checks, contact ARIETE customer service or your retailer for a thorough diagnosis.

Question 4

How to install and lock the lid of the RoboMix Compact 1769?

Accepted Answer

To install the lid of the ARIETE RoboMix Compact 1769, follow these steps:

Position the lid (O) on the bowl (P) by properly aligning the notch located inside the bowl with the corresponding symbol on the lid.
Lock the lid by turning it to the right until it clicks. This rotation ensures a secure and complete closure.
Check the locking: before turning on the device, make sure that the lid is firmly locked and that the bowl is correctly installed.

Important: The robot has a safety device that prevents it from operating if the lid is not properly locked or if the bowl is not installed. You will not be able to start the device until the assembly is complete.

Question 5

Why does water leak when I reinsert the tank after filling it?

Accepted Answer

When you reinsert the tank after filling it, a water leak may occur if the tank valve is not properly aligned with the fixing axis. According to the Steam Jet Pro 6248 manual, during reinstallation, you must align the tank valve with the axis - this is a critical step.

Here is the correct procedure:

Unplug the device before any handling
Remove the tank (O)
Turn the tank upside down and remove the cap (N)
Fill with fresh water directly from the tap, without exceeding the MAX level
Replace the cap
Carefully reinsert the tank, aligning its valve with the fixing axis

Other important points to avoid leaks:

Never fill the tank beyond the indicated MAX level
Ensure that the tank is securely locked in place
Never point the dispenser horizontally during use - this causes hot water leaks from the nozzles
Regularly check the water level while ironing

If leaks persist despite proper alignment, the tank seal may be worn. You can then order a replacement part from the manufacturer ARIETE.

Question 6

How do I open the bottom of the oven for cleaning?

Accepted Answer

First of all: wait for the oven to cool completely before accessing the lower part.

Procedure to access the crumb tray:

Turn the oven over using the specially designed knob for this purpose (Fig. 4)
Open the drawer by lifting it slightly upwards first (Fig. 5)

This gives you access to the crumb tray (E), the lower compartment that collects food residues.

Cleaning: Clean it with a damp sponge and remove any food, crumbs, or residues. This operation should be performed after each use for optimal operation of your oven.

Question 7

What is the capacity of the tank of the ARIETE XVapor Comfort 4145 steam cleaner?

Accepted Answer

The capacity of the tank of the ARIETE XVapor Comfort 4145 steam cleaner is 0.5 L (500 ml).

With this capacity, the device offers a continuous steam autonomy of up to 30 minutes. This autonomy is generally sufficient to effectively clean a medium-sized room without requiring additional refills.

The heating time of the device is approximately 5 minutes, allowing you to start cleaning quickly after turning it on.

Question 8

How to stop a running program and change programs on the ARIETE PANE EXPRESS?

Accepted Answer

To stop a running program on your ARIETE PANE EXPRESS bread machine and select another one, follow these steps:

1. Stop the current program

Locate the Stop or Cancel button on your device's control panel.
Press this button to interrupt the active program. This will stop the current cycle.

2. Wait for complete stop

Wait a moment for the machine to finish its stopping process. This ensures that the program is completely interrupted before proceeding.

3. Select a new program

Use the selection buttons to choose the desired new program.
Confirm your choice by pressing the start button.

These steps allow you to correct a selection error and easily start another program on your ARIETE PANE EXPRESS.

Question 9

How to replace the power cord of the ARIETE Bon Cuisine 974 oven?

Accepted Answer

To replace the power cord of your ARIETE Bon Cuisine 974 oven, follow these steps safely:

1. Unplug the oven

Before any intervention, make sure the oven is unplugged from the electrical outlet to avoid any risk of electric shock.

2. Access the power cord

Remove the screws or panels located at the back or underneath the oven to access the connection point of the power cord inside the appliance.

3. Disconnect the old cord

Identify the connections of the existing cord and carefully unplug it. Note or take a picture of how it is connected to facilitate the connection of the new cord.

4. Install the new cord

Connect the new power cord following the same connections as before. Ensure that the connections are secure and insulated.

5. Reassemble the oven

Replace the panels or screws you removed to access the cord.

6. Test the oven

Plug the oven back into the electrical outlet and turn it on to check that the cord replacement went well and that the appliance is functioning correctly.

Important: If you are not comfortable with electrical work, it is recommended to call a qualified professional to perform this replacement safely.

Question 10

What does the blinking light mean when cooking is finished on the ARIETE PANE EXPRESS METAL 125?

Accepted Answer

On the ARIETE PANE EXPRESS METAL 125, the blinking lights after cooking indicate that your bread has been baked and the machine automatically switches to warm keeping mode. During this phase, the 4 indicator lights located under the power button (A) blink to signal that the bread is being kept warm inside the appliance.

Duration of warm keeping: This function automatically lasts for 60 minutes after cooking is finished. Your bread remains warm and ready to be removed at any time during this period.

How to remove your bread: To take out the bread before the end of the 60 minutes of warm keeping, press the power button (A) to turn off the program. You can then open the lid and carefully remove your bread from the pan.

Beware of alarms: Do not confuse with alarm blinking: if the 5 indicator lights located under the program selection button (C) blink accompanied by a beeping sound, this indicates an overheating of the appliance. In this case, open the lid and let the machine cool down for 10 to 20 minutes before continuing.

Once the bread is removed, let it cool for about 20 minutes before slicing. Remember to turn off the appliance and unplug it before cleaning.

User manual ARIETE : user manuals and guides in PDF

Models ARIETE most viewed

Browse manuals ARIETE by appliance type

Recent questions about devices ARIETE