Q: What does the F1 code displayed on the screen mean?

The F1 code displayed on your Dolceclima Air Pro 13 A+ WiFi is a signal to clean the air filters . This message automatically appears every 250 hours of fan motor operation to remind you that filter maintenance is necessary. Your air conditioner has two types of filters : a main mesh filter (reusable and washable) and additional supplementary filters. To maintain effective filtration and ensure good cooling performance, it is recommended to clean the main filter every two weeks under normal use. The supplementary filters should be replaced every 500 hours of operation . Make sure to use only original Olimpia Splendid replacement parts. After cleaning the filters, you need to reset the F1 counter. Press and hold the ON/OFF button located on the device's control panel for 5 seconds . The F1 message will disappear and the counter will reset to zero. Do not turn the device back on without the main filter installed, as this would reduce its cooling capacity.

Q: What does the display "LO" mean on the Aquaria S1 10 P dehumidifier?

The display "LO" on your Olimpia Splendid Aquaria S1 10 P dehumidifier means that the ambient temperature is too low for the device to operate correctly. According to the technical specifications of the model, this dehumidifier is designed to operate within a temperature range of 5°C to 35°C . When the temperature drops below approximately 5°C , the system activates a protection function and displays this code to alert you. This protection is essential for the proper functioning of the dehumidification mechanism. The dehumidifier works by condensing moisture on its evaporator. At low temperatures, this condensation process becomes difficult or impossible, which is why the device automatically stops to protect you and preserve the compressor. To resolve this issue: first, ensure that the room temperature is above 5°C minimum . If necessary, move the dehumidifier to a warmer environment or increase the heating in the room. Once the ambient temperature exceeds the critical threshold (around 5°C), the "LO" display will automatically disappear, and the device will resume normal operation without any intervention from you. If the "LO" message still appears when you are certain that the temperature exceeds 5°C , it may indicate a malfunction of the temperature sensor . In this case, contact the Olimpia Splendid support service or an authorized repairer to have the sensor checked.

Q: What are the main features of the Olimpia Splendid Dolceclima 12 HP P portable air conditioner?

The Olimpia Splendid Dolceclima 12 HP P portable air conditioner is designed to provide optimal comfort in medium-sized spaces thanks to its various features: Operating modes Cooling: Effectively lowers the ambient temperature. Ventilation: Provides airflow without cooling for pleasant air circulation. Dehumidification: Reduces humidity in the air for a healthier environment. Main features Cooling capacity: 12,000 BTU, suitable for medium-sized rooms. Remote control: Remote included to adjust temperature, fan speed, and modes without moving. Timer function: Programming for automatic on and off according to your needs. Air filter: Captures dust and allergens to improve indoor air quality. Mobility: Compact design and integrated wheels for easy movement from room to room. Energy efficiency: Designed to limit electricity consumption while ensuring good performance. These features make the Dolceclima 12 HP P a versatile portable air conditioner, easy to use and suitable for daily air conditioning and ventilation needs.

Question 1

What does the F1 code displayed on the screen mean?

Accepted Answer

The F1 code displayed on your Dolceclima Air Pro 13 A+ WiFi is a signal to clean the air filters. This message automatically appears every 250 hours of fan motor operation to remind you that filter maintenance is necessary.

Your air conditioner has two types of filters: a main mesh filter (reusable and washable) and additional supplementary filters. To maintain effective filtration and ensure good cooling performance, it is recommended to clean the main filter every two weeks under normal use. The supplementary filters should be replaced every 500 hours of operation. Make sure to use only original Olimpia Splendid replacement parts.

After cleaning the filters, you need to reset the F1 counter. Press and hold the ON/OFF button located on the device's control panel for 5 seconds. The F1 message will disappear and the counter will reset to zero. Do not turn the device back on without the main filter installed, as this would reduce its cooling capacity.

Question 2

How to pair or synchronize the remote control of the UNICO air conditioner?

Accepted Answer

Unlike some devices, the OLIMPIA SPLENDID UNICO air conditioner does not require any pairing or synchronization procedure for the remote control.

Here’s what you need to do:

Install two 1.5V AAA (LR03) alkaline batteries in the remote control compartment, following the indicated polarities.
Point the remote control at the device's control panel.
A beep confirms the reception of commands.

If you do not receive any sound confirmation or if the buttons do not respond:

Check that the batteries are correctly installed and not depleted (the screen may darken if the batteries are weak).
Ensure there are no obstacles between the remote control and the device (effective range: about 8 meters maximum).
Replace the batteries if necessary.

In case of persistent malfunction, contact customer service.

Question 3

What does the flashing orange diode on my OLIMPIA SPLENDID Unico Inverter 13 A+ mean?

Accepted Answer

The flashing orange diode on your Olimpia Splendid Unico Inverter 13 A+ indicates a serious alarm state, usually accompanied by the simultaneous flashing of the green diode. This combination of intermittent lighting of the first two indicators (green and orange) indicates an anomaly in the condensate drainage system that has caused the automatic shutdown of the device.

The most likely causes are: a blocked or detached drainage pipe, insufficient slope of the drainage circuit (the minimum required slope is 3%), a buildup of dirt in the condensation battery, or a completely full condensate tank. The technical manual specifies that once this anomaly is detected, only cleaning the condensate management system and the condensation battery can restore operation.

Immediate procedure to follow: First, completely turn off the device and disconnect the power supply. Then, wait at least 3 minutes (compressor protection time) before inspecting the drainage circuit. Check that the condensate drainage pipe (minimum diameter 16 mm) is not blocked or crushed, that it is properly connected to the back of the unit, and especially that it slopes downwards towards the outside with a constant slope of at least 3%. Also, ensure that the recovery container (if there is one) is not hermetically sealed and that the pipe is not submerged in water.

If the problem persists after this check, the internal system requires professional cleaning. The manual states that cleaning the condensation battery and the condensate management system must be carried out exclusively by a certified technician. In this case, contact the support center mentioning specifically that the green and orange indicators are flashing together, which will greatly facilitate diagnosis.

In case of emergency or if water is visibly accumulating in the internal tank, you can proceed with an emergency manual drainage: first, place a container of at least 50 liters under the air conditioner, then carefully remove the drainage plug located at the bottom of the unit (see figure 23 of the technical manual). This operation must be performed with caution to avoid splashes.

Question 4

The remote control of my Dolceclima Air Pro 14 HP is not working - what should I do?

Accepted Answer

If your Dolceclima Air Pro 14 HP remote control is not working, the most common cause is a battery issue. Here are the troubleshooting steps to check in order:

Check and replace the batteries

Your remote control uses two AAA alkaline batteries of 1.5V
If the low battery icon (D12) appears on the remote control screen, the batteries are worn out and need to be replaced
Open the battery compartment (Figure 15 of the manual)
Ensure that both batteries match the polarity indicated at the bottom of the compartment (+ and -)
Always replace both batteries at the same time with new ones - using old or different types of batteries can cause malfunction of the remote control
Close the compartment properly

Check the range and eliminate obstacles

Maximum operating distance: approximately 8 meters with charged batteries
Point the remote control towards the device's receiver - the remote control works via infrared beam
Remove any obstacles between the remote control and the device (furniture, curtains, walls) that reduce the range
Do not expose the remote control directly to sunlight or too close to heat sources

Eliminate potential interference

Electronic and fluorescent lamps can interfere with infrared transmission
Other remote-controlled devices in the room (TV, stereo, etc.) can cause interference
Test the remote control in different areas away from these sources

Maintenance and protection of the remote control

Never wet the remote control - this may cause short circuits
Do not immerse or expose to excessive humidity
If the remote control remains unused for several weeks or more, remove the batteries to prevent leaks that could damage it
Clean the remote control only with a dry, soft cloth

If after thoroughly checking the batteries, range, and absence of interference the remote control still does not work, it is likely defective. Contact the retailer or the authorized OLIMPIA SPLENDID after-sales service for a replacement.

Question 5

How do I pair my phone with the air conditioner via WiFi?

Accepted Answer

Steps to pair your phone with the Dolceclima Air Pro 13 A+ WiFi:

Press the SW8 button on the device for about 3 seconds to activate the WiFi function. The screen will then display "AP", indicating that the device is in pairing mode.
On your phone, download the official OLIMPIA SPLENDID app from your app store (iOS or Android).
Launch the app and follow the setup instructions to connect your phone to the device's WiFi network.
Once pairing is complete, you will be able to control your air conditioner directly from your smartphone - temperature control, modes, and power remotely.

Make sure your phone has an active WiFi connection and that you are close to the device during the initial pairing.

Question 6

What does error code 8 mean on the Dolceclima Silent S1 10 P air conditioner?

Accepted Answer

The error code 8 is not listed in the official documentation for the Dolceclima Silent S1 10 P.

The documented error codes for this model are:

P1 - Lower tray full (empty it)
F1 - Filter cleaning required (after 250 hours of operation)
E1 to E4 - Sensor errors
EC - Refrigerant leak detection failure

If your unit displays code 8:

First, check that you are reading the code correctly (some codes may look similar on the screen)
Refer to section 6 - Troubleshooting in the manual for common issues (lack of cooling, noises, water leaks)
If code 8 persists, contact customer service, as this code is outside the range documented by the manufacturer

Question 7

Why does my dehumidifier turn off after 5 minutes of operation?

Accepted Answer

If your Olimpia Splendid Aquaria S1 20 P dehumidifier stops after 5 minutes of operation, the most likely cause is that you have set a timer for automatic shut-off. The device has a Timer function that allows you to schedule automatic on or off. To check: see if the LED L1 is lit (it indicates that the Timer function is active). If so, press the Timer button (D1) several times until '0' appears on the screen to completely cancel the timer programming.

If the Timer is not the cause: Next, check that the water tank is not full. When the LED L9 ('Water tank full') lights up, the device automatically stops and the buzzer emits a sound signal. Completely empty the 2.5-liter tank: remove it with both hands, open the tab (7b) at the bottom of the tank to let the water out, close the tab, and then correctly replace the tank in the body of the device.

Target humidity reached: Another common reason for stopping after a few minutes: the relative humidity in the room is already below the threshold you have set. Indeed, once the humidity drops below the configured level, the compressor temporarily stops to save energy. To check, press the 'Humidity level setting' button (D4) and slightly reduce the target value if you want the device to run longer.

Other possible causes: If the LED L4 (Defrost) lights up, the device is performing an automatic defrost cycle, which is normal. Also, ensure that the ambient temperature is between 5°C and 32°C, which is the normal operating range. A very dirty filter can also reduce efficiency and slow down moisture extraction; clean the air filter if it is very dirty.

After performing these checks, restart the device by plugging it back into the power outlet. If the shutdown persists after 5 minutes, consult the Olimpia Splendid technical support service.

Question 8

What does the display "LO" mean on the Aquaria S1 10 P dehumidifier?

Accepted Answer

The display "LO" on your Olimpia Splendid Aquaria S1 10 P dehumidifier means that the ambient temperature is too low for the device to operate correctly. According to the technical specifications of the model, this dehumidifier is designed to operate within a temperature range of 5°C to 35°C. When the temperature drops below approximately 5°C, the system activates a protection function and displays this code to alert you.

This protection is essential for the proper functioning of the dehumidification mechanism. The dehumidifier works by condensing moisture on its evaporator. At low temperatures, this condensation process becomes difficult or impossible, which is why the device automatically stops to protect you and preserve the compressor.

To resolve this issue: first, ensure that the room temperature is above 5°C minimum. If necessary, move the dehumidifier to a warmer environment or increase the heating in the room. Once the ambient temperature exceeds the critical threshold (around 5°C), the "LO" display will automatically disappear, and the device will resume normal operation without any intervention from you.

If the "LO" message still appears when you are certain that the temperature exceeds 5°C, it may indicate a malfunction of the temperature sensor. In this case, contact the Olimpia Splendid support service or an authorized repairer to have the sensor checked.

Question 9

How to perform periodic maintenance on the OLIMPIA SPLENDID Dolceclima 12 HP P air conditioner?

Accepted Answer

Regular maintenance of your OLIMPIA SPLENDID Dolceclima 12 HP P air conditioner is essential to ensure its proper functioning, efficiency, and durability. Here are the main steps to follow:

1. Cleaning the air filter

Check and clean the air filter every two weeks, especially during periods of intensive use. A clean filter improves air quality and optimizes the device's performance. To clean it, gently remove it, then vacuum the dust or rinse it with warm water. Ensure it is completely dry before putting it back in place.

2. Checking the drain

Regularly check that the water drainage is not blocked. A clogged drain can cause water leaks and promote the growth of mold.

3. Cleaning the external unit

If your model has an external unit, ensure it is clean and free from any obstructions (leaves, dust, debris) to ensure good air circulation.

4. Checking for refrigerant leaks

Regularly inspect the air conditioner for any refrigerant gas leaks. If you suspect a leak, call a qualified professional to carry out the repair.

5. Testing functions

Periodically test all functions of the device (cooling, ventilation, dehumidification) to verify their proper operation.

6. Storage during periods of non-use

If you do not use the air conditioner for an extended period, clean it thoroughly and store it in a dry, cool place.

7. Professional maintenance

It is recommended to have a complete maintenance performed by a professional at least once a year to ensure the longevity and safety of your device.

By following these tips, you will help keep your OLIMPIA SPLENDID Dolceclima 12 HP P in perfect working condition and extend its lifespan.

Question 10

What are the main features of the Olimpia Splendid Dolceclima 12 HP P portable air conditioner?

Accepted Answer

The Olimpia Splendid Dolceclima 12 HP P portable air conditioner is designed to provide optimal comfort in medium-sized spaces thanks to its various features:

Operating modes

Cooling: Effectively lowers the ambient temperature.
Ventilation: Provides airflow without cooling for pleasant air circulation.
Dehumidification: Reduces humidity in the air for a healthier environment.

Main features

Cooling capacity: 12,000 BTU, suitable for medium-sized rooms.
Remote control: Remote included to adjust temperature, fan speed, and modes without moving.
Timer function: Programming for automatic on and off according to your needs.
Air filter: Captures dust and allergens to improve indoor air quality.
Mobility: Compact design and integrated wheels for easy movement from room to room.
Energy efficiency: Designed to limit electricity consumption while ensuring good performance.

These features make the Dolceclima 12 HP P a versatile portable air conditioner, easy to use and suitable for daily air conditioning and ventilation needs.

User manual OLIMPIA SPLENDID : user manuals and guides in PDF

Models OLIMPIA SPLENDID most viewed

Browse manuals OLIMPIA SPLENDID by appliance type

Recent questions about devices OLIMPIA SPLENDID