Q: What does the display "LO" mean on the Aquaria S1 10 P dehumidifier?

The display "LO" on your Olimpia Splendid Aquaria S1 10 P dehumidifier means that the ambient temperature is too low for the device to operate correctly. According to the technical specifications of the model, this dehumidifier is designed to operate within a temperature range of 5°C to 35°C . When the temperature drops below approximately 5°C , the system activates a protection function and displays this code to alert you. This protection is essential for the proper functioning of the dehumidification mechanism. The dehumidifier works by condensing moisture on its evaporator. At low temperatures, this condensation process becomes difficult or impossible, which is why the device automatically stops to protect you and preserve the compressor. To resolve this issue: first, ensure that the room temperature is above 5°C minimum . If necessary, move the dehumidifier to a warmer environment or increase the heating in the room. Once the ambient temperature exceeds the critical threshold (around 5°C), the "LO" display will automatically disappear, and the device will resume normal operation without any intervention from you. If the "LO" message still appears when you are certain that the temperature exceeds 5°C , it may indicate a malfunction of the temperature sensor . In this case, contact the Olimpia Splendid support service or an authorized repairer to have the sensor checked.

Question 1

Why does my dehumidifier turn off after 5 minutes of operation?

Accepted Answer

If your Olimpia Splendid Aquaria S1 20 P dehumidifier stops after 5 minutes of operation, the most likely cause is that you have set a timer for automatic shut-off. The device has a Timer function that allows you to schedule automatic on or off. To check: see if the LED L1 is lit (it indicates that the Timer function is active). If so, press the Timer button (D1) several times until '0' appears on the screen to completely cancel the timer programming.

If the Timer is not the cause: Next, check that the water tank is not full. When the LED L9 ('Water tank full') lights up, the device automatically stops and the buzzer emits a sound signal. Completely empty the 2.5-liter tank: remove it with both hands, open the tab (7b) at the bottom of the tank to let the water out, close the tab, and then correctly replace the tank in the body of the device.

Target humidity reached: Another common reason for stopping after a few minutes: the relative humidity in the room is already below the threshold you have set. Indeed, once the humidity drops below the configured level, the compressor temporarily stops to save energy. To check, press the 'Humidity level setting' button (D4) and slightly reduce the target value if you want the device to run longer.

Other possible causes: If the LED L4 (Defrost) lights up, the device is performing an automatic defrost cycle, which is normal. Also, ensure that the ambient temperature is between 5°C and 32°C, which is the normal operating range. A very dirty filter can also reduce efficiency and slow down moisture extraction; clean the air filter if it is very dirty.

After performing these checks, restart the device by plugging it back into the power outlet. If the shutdown persists after 5 minutes, consult the Olimpia Splendid technical support service.

Question 2

What does the display "LO" mean on the Aquaria S1 10 P dehumidifier?

Accepted Answer

The display "LO" on your Olimpia Splendid Aquaria S1 10 P dehumidifier means that the ambient temperature is too low for the device to operate correctly. According to the technical specifications of the model, this dehumidifier is designed to operate within a temperature range of 5°C to 35°C. When the temperature drops below approximately 5°C, the system activates a protection function and displays this code to alert you.

This protection is essential for the proper functioning of the dehumidification mechanism. The dehumidifier works by condensing moisture on its evaporator. At low temperatures, this condensation process becomes difficult or impossible, which is why the device automatically stops to protect you and preserve the compressor.

To resolve this issue: first, ensure that the room temperature is above 5°C minimum. If necessary, move the dehumidifier to a warmer environment or increase the heating in the room. Once the ambient temperature exceeds the critical threshold (around 5°C), the "LO" display will automatically disappear, and the device will resume normal operation without any intervention from you.

If the "LO" message still appears when you are certain that the temperature exceeds 5°C, it may indicate a malfunction of the temperature sensor. In this case, contact the Olimpia Splendid support service or an authorized repairer to have the sensor checked.

User manual OLIMPIA SPLENDID Dehumidifier : user manuals and guides in PDF

Models OLIMPIA SPLENDID Dehumidifier most viewed

Other categories OLIMPIA SPLENDID

Recent questions about Dehumidifier OLIMPIA SPLENDID