Q: Where is the power button on the T-FAL ULTRAGLIDE EASYCORD FV4379 iron?

This T-FAL iron does not have a traditional power button. It simply activates by plugging it into an electrical outlet and automatically turns off after 8 minutes in an upright position or 30 seconds in a horizontal position. The main controls you will find on this iron are: Temperature adjustment dial (fig. 5) - Turn it to select the desired temperature Steam control (fig. 7) - Continuously adjustable to adjust the steam flow Steam boost button (fig. 8) - Press to get more steam Water spray button (fig. 9) - Sprays a fine mist on fabrics Self-cleaning button (fig. 14a) - Used for cleaning the iron Easycord system extension button (fig. 4) - Automatically deploys the cord guide A just temperature indicator (fig. 6) lets you know when the iron has reached the selected temperature.

Question 1

My T-FAL ULTRAGLIDE EASYCORD FV4379 iron does not heat up when I plug it in. What should I do?

Accepted Answer

The T-FAL ULTRAGLIDE EASYCORD FV4379 iron does not have a traditional power button - it activates automatically as soon as it is plugged in. Here’s how to check its operation:

Essential Checks

Check the temperature indicator light (fig. 6): after plugging it in, this light should turn on immediately. It will stay on during heating and will turn off once the temperature is reached. Wait a few minutes - heating can take time.
Check the temperature selector: make sure the temperature dial is set to an appropriate setting (between 3 and MAX depending on the fabric). If it is set too low, the iron may heat slowly.
Check your electrical outlet: test the outlet with another device to confirm it is working properly. Inspect the power cord for visible damage.
Wait long enough: before concluding that the iron does not heat, leave it plugged in for at least 3-5 minutes and place your hand near the soleplate to check if it gets warm.

If the iron remains cold

If the temperature indicator light does not turn on after plugging in or if the iron does not heat up after 5 minutes, the problem is likely due to an internal electrical fault. In this case, contact T-FAL customer service for repair or replacement.

Question 2

Where is the power button on the T-FAL ULTRAGLIDE EASYCORD FV4379 iron?

Accepted Answer

This T-FAL iron does not have a traditional power button. It simply activates by plugging it into an electrical outlet and automatically turns off after 8 minutes in an upright position or 30 seconds in a horizontal position.

The main controls you will find on this iron are:

Temperature adjustment dial (fig. 5) - Turn it to select the desired temperature
Steam control (fig. 7) - Continuously adjustable to adjust the steam flow
Steam boost button (fig. 8) - Press to get more steam
Water spray button (fig. 9) - Sprays a fine mist on fabrics
Self-cleaning button (fig. 14a) - Used for cleaning the iron
Easycord system extension button (fig. 4) - Automatically deploys the cord guide

A just temperature indicator (fig. 6) lets you know when the iron has reached the selected temperature.

Question 3

How do I clean the stains on the soleplate of my T-FAL ULTRAGLIDE Anti-Calc iron?

Accepted Answer

To remove stains from the soleplate of your T-FAL ULTRAGLIDE Anti-Calc iron, follow these simple steps:

Steps to clean the iron's soleplate:

Unplug and let cool: Make sure the iron is unplugged and completely cool before starting the cleaning process.
Gentle cleaning: Dampen a soft cloth with a little warm water. For more effective cleaning, you can add a bit of diluted white vinegar.
Wipe the soleplate: Gently rub the soleplate with the damp cloth to remove light stains. Avoid abrasive materials that could scratch the surface.
For stubborn stains: Prepare a paste by mixing baking soda with a little water. Apply this paste to the stained areas and gently rub with a soft cloth or a non-abrasive sponge.
Rinsing: Then wipe the soleplate with a clean, damp cloth to remove any residue of baking soda or vinegar.
Drying: Dry the soleplate with a soft, dry cloth before storing or using the iron again.
Cleaning steam holes: If necessary, use a cotton swab dipped in white vinegar to clean the holes in the soleplate and remove any limescale deposits.

By following these tips, you can keep the soleplate of your iron clean and in good condition, ensuring better glide and effective ironing.

User manual T-FAL : user manuals and guides in PDF

Models T-FAL most viewed

Browse manuals T-FAL by appliance type

Recent questions about devices T-FAL