Q: What does error code E92 mean on my TORSBODA dishwasher?

The error code E92 (or E:92-40) on your IKEA TORSBODA dishwasher means that the filters are dirty or blocked . This usually occurs when food residues or limescale accumulate in the filtration system, which can reduce washing efficiency and trigger the alert. To resolve this issue, follow these steps: Turn off the appliance and completely empty the bottom basket Access the filter system : turn the coarse filter counterclockwise to remove the entire filtration system located at the bottom of the tub Remove the fine filter by pulling it down Clean the filter elements under running water by removing all residues and food debris Gently clean the rim located between the coarse and fine filters to remove any dirt buildup Reassemble the system : ensure that the locking latches of the coarse filter are properly in place, then reinsert the assembly into the appliance and turn the coarse filter clockwise to secure it (make sure the arrow markings align) After cleaning the filters, restart a washing cycle. If the error code persists, also check that the spray arms are not clogged — you can clean them by removing and inspecting the spray nozzles under running water. Maintenance tip: clean the filters after each wash to maintain optimal performance of your TORSBODA (12 place settings, 9.9 liters of water per cycle) and prevent this error from recurring. Regular maintenance ensures a longer lifespan for your appliance and guarantees optimal A++ energy class.

Q: My STYRBAR remote control no longer controls the LEDs even after changing the batteries and resetting - what should I do?

Your problem: Your STYRBAR 304.883.63 remote control no longer communicates with the LEDs, even after changing the batteries and attempting to reset. Steps to follow in order: Step 1 - Completely reset both devices: Start with the light source: turn its main switch on and off 6 times in a row (press quickly). Then, reset the remote control by pressing the pairing button 4 times within 5 seconds - a red light will turn on the remote control to confirm. Step 2 - Check and change the batteries if necessary: Use 2 new AAA/HR03 batteries. The batteries recommended by IKEA are the IKEA LADDA 900 (1.2 V, 900 mAh, Ni-MH). Make sure not to mix batteries of different capacities or dates. Step 3 - Pair again: Once both devices are reset, hold the remote control less than 5 cm from the light source. Press the pairing button 4 times within 5 seconds . A steady red light will turn on the remote control. The light should start to dim and then blink once - this is the signal that pairing was successful. Step 4 - Test: If the light does not react after blinking, pairing did not work. Try steps 1-3 again. Also, check that nothing is obstructing the range: the remote control has a range of 10 m in free field , but some building materials may affect this distance. If nothing works: After trying several times, the problem may be an electronic failure of one of the two units. Contact IKEA customer service with your proof of purchase - they will be able to offer you a replacement under warranty.

Q: What does the Fresh Plus button do?

The Fresh Plus button (button 8) generates steam aimed at inhibiting the proliferation of unpleasant odors. After this steam phase, the drum performs slow rotations. Operation Duration: up to 6 hours maximum Starts after the washing cycle Can be interrupted at any time by pressing any button A light indicator illuminates once the button is pressed Important: you must wait about 5 minutes before you can open the door after activation This function is particularly useful if you cannot start a cycle immediately after washing, or if you want to refresh the laundry without restarting a full program.

Q: What to do in case of E1 error on the IKEA FRÖSLUNDA dishwasher if water is not draining and the filter is clean?

The E1 error on your IKEA FRÖSLUNDA indicates a water filling issue . If the filter is already clean, here are the points to check as a priority: Check the water supply: make sure that the water tap is fully open and that the inlet hose is not bent, twisted, or crushed. The machine requires a water pressure between 0.4 and 10 bar to operate correctly. If the pressure is too low, contact your local water service. Also, check that the water tap is not blocked and that the filter located at the inlet of the supply hose (inside the connection to the machine) is not obstructed by impurities. Check the water drainage: although the E1 error mainly concerns filling, a drainage issue can affect operation. Ensure that the drain hose is not bent, twisted, or crushed. Check that the filter of the drain hose is not blocked and that the sink connection has no obstructions. The internal filtering system should not be blocked either. Regenerate the softener: after a long period of inactivity or maintenance, the resin system of the water softener needs to regenerate, which takes about 5 minutes. During this time, the machine may not fill properly. Wait a few minutes before restarting a program. If after these checks the E1 error persists or if water still does not drain, the problem likely comes from an internal component (pump, solenoid valve, or faulty water level sensor) and will require technical intervention from an authorized IKEA service center.

Q: How to set the Quick program on the IKEA FRÖSLUNDA dishwasher?

The IKEA FRÖSLUNDA dishwasher offers a Quick program designed for lightly soiled loads, lasting about 30 minutes. Steps to activate the Quick program Press the power button to turn on the appliance Press the program button to select the Quick program The program indicator lights up and the display shows the cycle duration Close the door to start the cycle The Quick program has three washing phases: Washing at 40 °C, Rinsing, then Rinsing at 45 °C. It consumes about 10.2 liters of water and 0.600 kWh per cycle. You can combine this program with the Tablet function or activate the delayed start if necessary. Note that the Quick program does not have a drying phase.

Q: How to turn off the button sounds of the IKEA FRÖSLUNDA dishwasher?

To turn off the button sounds of the IKEA FRÖSLUNDA dishwasher, follow these steps: Press the power button to turn the appliance on. Hold the buttons down for 3 seconds . This combination toggles the button sounds between on and off. Repeat the same operation to reactivate the sounds if desired. Note: The FRÖSLUNDA dishwasher does not have a volume control. The control is limited to completely turning the beeping sounds of the controls on or off.

Q: Does the user mode exist on older models of the IKEA RENGORA dishwasher 703.858.34 and what settings can be configured?

Yes, your IKEA RENGORA 703.858.34 model has a user mode that allows you to customize several settings of the appliance. How to access user mode Press and hold both program buttons simultaneously until the indicators flash and the screen clears. You are then in user mode. Configurable settings Water softener level : Adjustable from 1 to 10 depending on the local water hardness End of program beep : You can enable or disable the end of cycle beep TimeBeam color : Select from several options or disable the light indicator Rinse aid notification : Enable or disable the rinse aid tank filling alert Rinse aid level : Set the dosage from 0 to 6 AutoOpen : Enable or disable the automatic door opening after the cycle These settings allow you to tailor the operation of your dishwasher to your personal preferences and the characteristics of your local water.

Q: Does the IKEA RENGORA 703.858.34 dishwasher come in several variants and how can I identify mine?

The IKEA RENGORA 703.858.34 model marketed as a 15-place built-in dishwasher has a unique configuration with a digital control panel and TimeBeam display. There are no distinct official variants with different control systems (mechanical vs. digital). How to identify your appliance: Look at the control panel located at the top of the dishwasher door. You will see a digital screen displaying the program number and a power button on the left, followed by program selection buttons (up/down), a delayed start button, and buttons for the ExtraHygiene and DryPlus options on the right. The appliance also features a floor projection (TimeBeam) that displays the duration and status of the program. Available programs and options: Your model includes 7 distinct programs (Auto, Heavy 70°C, Quick 60°C, Eco 50°C, Glass 45°C, Rinse & Hold, Extra Silent 50°C) accessible via the digital panel. Options such as DryPlus (enhances drying), ExtraHygiene (70°C for 10 minutes), AutoOpen (automatic door opening), and delayed start (1 to 24 hours) are integrated. Available settings: In user mode (accessible by holding the up and down program buttons), you can adjust the water softener according to your region (level 1 to 10), the rinse aid level (0 to 6), the color of the TimeBeam, the sound signals, and the activation/deactivation of AutoOpen. These settings are retained between cycles. If you have questions about the operation or specific settings, refer to the "Settings" and "Daily Use" sections of the manual for exact procedures. All RENGORA 703.858.34 models operate under the same digital control system.

Question 1

Why is my RENODLAD dishwasher leaking water under the door?

Accepted Answer

A water leak under the door of the RENODLAD dishwasher usually comes from a lack of sealing related to the positioning of the appliance or the door itself. Here are the solutions to apply in order:

Step 1: Check the level of the appliance

The dishwasher must be perfectly level (horizontal). If the appliance is not level, water will accumulate under the door and leak out.

Look under the appliance and locate the adjustable leveling feet
Loosen or tighten these feet as needed to place the appliance completely horizontal
Use a bubble level to check

Step 2: Check the door alignment

If the door is not properly centered on the tub, the door seal will not create a complete seal, leading to the leak. This is often the main cause.

Open the door completely and observe its alignment with the casing
If it is not centered, adjust the rear foot (if applicable to your model) to recenter the door
Close the door gently and check that the gap is equal on both sides

Step 3: Inspect the door seal

If the leak persists after adjusting the level and alignment, inspect the rubber seal around the door:

Check for debris, hair, or detergent residue stuck in the seal
Gently clean with a damp cloth and soapy water
Ensure that the seal is not damaged or deformed

If the problem persists after these checks: Contact IKEA customer service. The door seal or the door itself may have a manufacturing defect covered by the IKEA 5-year warranty.

Question 2

What does error code E92 mean on my TORSBODA dishwasher?

Accepted Answer

The error code E92 (or E:92-40) on your IKEA TORSBODA dishwasher means that the filters are dirty or blocked. This usually occurs when food residues or limescale accumulate in the filtration system, which can reduce washing efficiency and trigger the alert.

To resolve this issue, follow these steps:

Turn off the appliance and completely empty the bottom basket
Access the filter system: turn the coarse filter counterclockwise to remove the entire filtration system located at the bottom of the tub
Remove the fine filter by pulling it down
Clean the filter elements under running water by removing all residues and food debris
Gently clean the rim located between the coarse and fine filters to remove any dirt buildup
Reassemble the system: ensure that the locking latches of the coarse filter are properly in place, then reinsert the assembly into the appliance and turn the coarse filter clockwise to secure it (make sure the arrow markings align)

After cleaning the filters, restart a washing cycle. If the error code persists, also check that the spray arms are not clogged — you can clean them by removing and inspecting the spray nozzles under running water.

Maintenance tip: clean the filters after each wash to maintain optimal performance of your TORSBODA (12 place settings, 9.9 liters of water per cycle) and prevent this error from recurring. Regular maintenance ensures a longer lifespan for your appliance and guarantees optimal A++ energy class.

Question 3

My STYRBAR remote control no longer controls the LEDs even after changing the batteries and resetting - what should I do?

Accepted Answer

Your problem: Your STYRBAR 304.883.63 remote control no longer communicates with the LEDs, even after changing the batteries and attempting to reset.

Steps to follow in order:

Step 1 - Completely reset both devices: Start with the light source: turn its main switch on and off 6 times in a row (press quickly). Then, reset the remote control by pressing the pairing button 4 times within 5 seconds - a red light will turn on the remote control to confirm.
Step 2 - Check and change the batteries if necessary: Use 2 new AAA/HR03 batteries. The batteries recommended by IKEA are the IKEA LADDA 900 (1.2 V, 900 mAh, Ni-MH). Make sure not to mix batteries of different capacities or dates.
Step 3 - Pair again: Once both devices are reset, hold the remote control less than 5 cm from the light source. Press the pairing button 4 times within 5 seconds. A steady red light will turn on the remote control. The light should start to dim and then blink once - this is the signal that pairing was successful.
Step 4 - Test: If the light does not react after blinking, pairing did not work. Try steps 1-3 again. Also, check that nothing is obstructing the range: the remote control has a range of 10 m in free field, but some building materials may affect this distance.

If nothing works: After trying several times, the problem may be an electronic failure of one of the two units. Contact IKEA customer service with your proof of purchase - they will be able to offer you a replacement under warranty.

Question 4

What does the Fresh Plus button do?

Accepted Answer

The Fresh Plus button (button 8) generates steam aimed at inhibiting the proliferation of unpleasant odors. After this steam phase, the drum performs slow rotations.

Operation

Duration: up to 6 hours maximum
Starts after the washing cycle
Can be interrupted at any time by pressing any button
A light indicator illuminates once the button is pressed
Important: you must wait about 5 minutes before you can open the door after activation

This function is particularly useful if you cannot start a cycle immediately after washing, or if you want to refresh the laundry without restarting a full program.

Question 5

What to do in case of E1 error on the IKEA FRÖSLUNDA dishwasher if water is not draining and the filter is clean?

Accepted Answer

The E1 error on your IKEA FRÖSLUNDA indicates a water filling issue. If the filter is already clean, here are the points to check as a priority:

Check the water supply: make sure that the water tap is fully open and that the inlet hose is not bent, twisted, or crushed. The machine requires a water pressure between 0.4 and 10 bar to operate correctly. If the pressure is too low, contact your local water service. Also, check that the water tap is not blocked and that the filter located at the inlet of the supply hose (inside the connection to the machine) is not obstructed by impurities.

Check the water drainage: although the E1 error mainly concerns filling, a drainage issue can affect operation. Ensure that the drain hose is not bent, twisted, or crushed. Check that the filter of the drain hose is not blocked and that the sink connection has no obstructions. The internal filtering system should not be blocked either.

Regenerate the softener: after a long period of inactivity or maintenance, the resin system of the water softener needs to regenerate, which takes about 5 minutes. During this time, the machine may not fill properly. Wait a few minutes before restarting a program.

If after these checks the E1 error persists or if water still does not drain, the problem likely comes from an internal component (pump, solenoid valve, or faulty water level sensor) and will require technical intervention from an authorized IKEA service center.

Question 6

How to set the Quick program on the IKEA FRÖSLUNDA dishwasher?

Accepted Answer

The IKEA FRÖSLUNDA dishwasher offers a Quick program designed for lightly soiled loads, lasting about 30 minutes.

Steps to activate the Quick program

Press the power button to turn on the appliance
Press the program button to select the Quick program
The program indicator lights up and the display shows the cycle duration
Close the door to start the cycle

The Quick program has three washing phases: Washing at 40 °C, Rinsing, then Rinsing at 45 °C. It consumes about 10.2 liters of water and 0.600 kWh per cycle.

You can combine this program with the Tablet function or activate the delayed start if necessary. Note that the Quick program does not have a drying phase.

Question 7

How to turn off the button sounds of the IKEA FRÖSLUNDA dishwasher?

Accepted Answer

To turn off the button sounds of the IKEA FRÖSLUNDA dishwasher, follow these steps:

Press the power button to turn the appliance on.
Hold the buttons down for 3 seconds.

This combination toggles the button sounds between on and off. Repeat the same operation to reactivate the sounds if desired.

Note: The FRÖSLUNDA dishwasher does not have a volume control. The control is limited to completely turning the beeping sounds of the controls on or off.

Question 8

Does the user mode exist on older models of the IKEA RENGORA dishwasher 703.858.34 and what settings can be configured?

Accepted Answer

Yes, your IKEA RENGORA 703.858.34 model has a user mode that allows you to customize several settings of the appliance.

How to access user mode

Press and hold both program buttons simultaneously until the indicators flash and the screen clears. You are then in user mode.

Configurable settings

Water softener level: Adjustable from 1 to 10 depending on the local water hardness
End of program beep: You can enable or disable the end of cycle beep
TimeBeam color: Select from several options or disable the light indicator
Rinse aid notification: Enable or disable the rinse aid tank filling alert
Rinse aid level: Set the dosage from 0 to 6
AutoOpen: Enable or disable the automatic door opening after the cycle

These settings allow you to tailor the operation of your dishwasher to your personal preferences and the characteristics of your local water.

Question 9

Does the IKEA RENGORA 703.858.34 dishwasher come in several variants and how can I identify mine?

Accepted Answer

The IKEA RENGORA 703.858.34 model marketed as a 15-place built-in dishwasher has a unique configuration with a digital control panel and TimeBeam display. There are no distinct official variants with different control systems (mechanical vs. digital).

How to identify your appliance: Look at the control panel located at the top of the dishwasher door. You will see a digital screen displaying the program number and a power button on the left, followed by program selection buttons (up/down), a delayed start button, and buttons for the ExtraHygiene and DryPlus options on the right. The appliance also features a floor projection (TimeBeam) that displays the duration and status of the program.

Available programs and options: Your model includes 7 distinct programs (Auto, Heavy 70°C, Quick 60°C, Eco 50°C, Glass 45°C, Rinse & Hold, Extra Silent 50°C) accessible via the digital panel. Options such as DryPlus (enhances drying), ExtraHygiene (70°C for 10 minutes), AutoOpen (automatic door opening), and delayed start (1 to 24 hours) are integrated.

Available settings: In user mode (accessible by holding the up and down program buttons), you can adjust the water softener according to your region (level 1 to 10), the rinse aid level (0 to 6), the color of the TimeBeam, the sound signals, and the activation/deactivation of AutoOpen. These settings are retained between cycles.

If you have questions about the operation or specific settings, refer to the "Settings" and "Daily Use" sections of the manual for exact procedures. All RENGORA 703.858.34 models operate under the same digital control system.

Question 10

What do the numbers on the salt compartment of the IKEA RENGORA 703.858.34 dishwasher correspond to and how to use them?

Accepted Answer

The salt compartment of your IKEA RENGORA 703.858.34 dishwasher is equipped with a water hardness regulator with numbers from 1 to 10 (you may have observed part of this range depending on the viewing angle).

What are these numbers for?

These levels allow you to adjust the built-in water softener according to the hardness of the water in your area. The harder the water in your area, the higher you need to set the level.

How to adjust the hardness level?

Set the appliance to program selection mode.
Press the program buttons simultaneously until the indicators flash.
Press the Program Down button to display the current setting (e.g., SL = level 5).
Press again to change the level between 1 and 10.
Confirm with the On/Off button.

Which level to choose?

The factory setting is level 5. Check with your local water supplier to find out the hardness of your water (in degrees German °dH, French °fH, or English) and refer to the conversion table provided in your manual to determine the optimal level.

User manual IKEA : user manuals and guides in PDF

Models IKEA most viewed

Browse manuals IKEA by appliance type

Recent questions about devices IKEA