Q: What blades and knives are compatible with the Gardol GBM-E 51 R HW E?

The Gardol GBM-E 51 R HW E lawn mower uses a genuine Einhell blade compatible with its cutting width of 510 mm . According to the manufacturer's manual, only genuine factory parts should be used for blade replacement, as using non-approved blades may unbalance the motor and damage your mower. How to obtain the genuine blade: Contact your authorized Einhell/Gardol dealer or the ISC-GmbH customer service (manufacturer) Provide the following information: Exact model: GBM-E 51 R HW E Article number: 34.043.56 Your serial number (visible on the device) For complete and up-to-date information on prices and availability, visit www.isc-gmbh.info or contact info@isc-gmbh.info Maintenance and blade replacement: The manual specifies that sharpening, balancing, and mounting of the blade must be carried out by an authorized service workshop . It is recommended to have the condition of the blade checked at least once a year to ensure optimal operation and maximum safety. Do not attempt to straighten a bent or damaged blade: it must be replaced with a genuine blade. Important: Blades and other wear parts are not covered by the manufacturer's warranty . They are considered consumables whose wear depends on usage and maintenance conditions.

Question 1

Where is the lower motor cover located and how can I access it?

Accepted Answer

The lower motor cover (motor cover) of your Gardol GEME 1536 lawn mower is located under the main motor housing, at the bottom of the device, directly beneath the motor block that drives the cutting blade.

To access this area:

Always unplug the power plug from the wall socket before performing any work
Place the lawn mower on a flat and stable surface
Gently tilt the lawn mower backward to have comfortable access to the lower part
The lower cover is usually held in place by a few fastening screws that you can unscrew with a suitable screwdriver

This area is important for motor maintenance. According to the manual, you should regularly check that all fastening elements (screws, nuts, etc.) are properly tightened to ensure safe use. You should also keep the motor housing as clean and dust-free as possible by wiping it with a clean cloth or blowing it with low-pressure compressed air.

Important notice: Only a qualified electrician is authorized to replace the carbon brushes. For any complex intervention on the motor, please contact our customer service or a duly authorized specialized workshop. Never use running water or high-pressure cleaner to clean your lawn mower, as this could damage the internal electrical components.

Question 2

What blades and knives are compatible with the Gardol GBM-E 51 R HW E?

Accepted Answer

The Gardol GBM-E 51 R HW E lawn mower uses a genuine Einhell blade compatible with its cutting width of 510 mm. According to the manufacturer's manual, only genuine factory parts should be used for blade replacement, as using non-approved blades may unbalance the motor and damage your mower.

How to obtain the genuine blade:

Contact your authorized Einhell/Gardol dealer or the ISC-GmbH customer service (manufacturer)
Provide the following information:
- Exact model: GBM-E 51 R HW E
- Article number: 34.043.56
- Your serial number (visible on the device)
For complete and up-to-date information on prices and availability, visit www.isc-gmbh.info or contact info@isc-gmbh.info

Maintenance and blade replacement:

The manual specifies that sharpening, balancing, and mounting of the blade must be carried out by an authorized service workshop. It is recommended to have the condition of the blade checked at least once a year to ensure optimal operation and maximum safety. Do not attempt to straighten a bent or damaged blade: it must be replaced with a genuine blade.

Important: Blades and other wear parts are not covered by the manufacturer's warranty. They are considered consumables whose wear depends on usage and maintenance conditions.

Question 3

Where is the lever to adjust the cutting size on the Gardol GLH-E 2540?

Accepted Answer

The adjustment knob for the counter blade of the Gardol GLH-E 2540 is located on the right side of the plastic housing. It is an easily identifiable rotary knob that allows you to adjust the spacing between the counter blade and the chopping knife.

How the adjustment works: By turning the knob to the right, you bring the counter blade closer to the chopping knife. By turning to the left, you move the counter blade away. Each half turn of the knob changes the spacing by about 0.50 mm.

Optimal spacing: For the chopper to function correctly, the gap between the counter blade and the chopping knife should be about 0.50 mm. After each adjustment, check that the knife cuts properly by performing a test with appropriate material.

Adjustment procedure: Ensure that the device is completely stopped and unplugged before intervening. Locate the knob on the right side of the housing, then gradually turn it while observing the approach of the counter blade. Quarters or half turns are usually sufficient to achieve the desired adjustment.

If the knob is damaged or missing, or if the device does not cut properly after adjustment, contact a Gardol or Einhell dealer to order the replacement knob.

User manual Gardol : user manuals and guides in PDF

Models Gardol most viewed

Browse manuals Gardol by appliance type

Recent questions about devices Gardol