Q: Can this refrigerator operate on gas?

No, the DOMETIC RCD 10.5T cannot operate on gas. It is a compressor refrigerator that operates exclusively on electricity . The power specifications for this model are: Connection voltage: 12 V DC Average power consumption: 54 W Energy consumption: 0.70 kWh per 24 hours This refrigerator is designed for use with direct current (typically powered by a battery, a solar panel with an inverter, or a stabilized external 12 V power supply). There is no gas operation option for this model.

Q: How do I set the temperature of the DOMETIC DM50CF refrigerator?

The DOMETIC DM50CF refrigerator has three temperature levels : 4°C (39°F), 7°C (45°F), and 12°C (54°F). Steps to change the temperature: Press and hold the adjustment button for 3 seconds until the interior light starts to blink Press the button again immediately The number of blinks of the light indicates the selected temperature: 5 blinks = 4°C (the coldest, ideal for quick freezing) 3 blinks = 7°C (default setting at 25°C ambient) 1 blink = 12°C (the least cold, for light preservation) The temperatures cycle in this order: 4°C → 7°C → 12°C → then start over in a loop. The manual recommends selecting the middle level (7°C) and adjusting according to the quantity and type of food stored to avoid spoilage.

Q: Is it normal for the refrigerator compressor to be hot and the fan to be running?

Yes, this is completely normal. The DOMETIC RC 10.4T 70 is designed for the refrigeration unit (compressor and condenser) located at the back to become very hot during operation. This is the natural and intended operation of the refrigerator. The heat generated is dissipated by the external ventilation fan, which runs precisely to cool the unit and prevent dangerous overheating. The behavior you observe depends on the selected operating mode: in Performance mode , the compressor and fan run at high speed, generating more heat and noise (about 42 dB); in Quiet mode , they operate at low speed for less noise (39 dB); in Boost mode , they run at high speed for maximum cooling. The lower the temperature setting or the hotter it is around the refrigerator, the harder the compressor works and the more heat is generated. To check that your refrigerator is functioning correctly, ensure that: the internal temperature gradually decreases after starting; the compressor (blue snowflake on the screen) stops once the desired temperature is reached; air circulates freely around the refrigerator without blockage of the rear ventilation grilles; the refrigerator is at least a few centimeters away from walls or objects to allow heat dissipation. It is normal and expected for the refrigeration unit to be hot to the touch: do not touch the heat-conducting parts at the back to avoid burns. Ensure that heat can dissipate properly; otherwise, the refrigerator may go into thermal protection. If an error code is displayed on the screen (for example, E34 for compressor overload), contact an authorized Dometic service center.

Q: Does the refrigerator automatically switch to 12V battery power while driving?

The DOMETIC RM 8405 uses an AES (Automatic Energy Selection) system that automatically selects the available power source according to the following priority order: Solar panels (if available) 230V AC mains 12V vehicle battery Liquefied gas (last resort) Important: The system does NOT automatically switch TO the 12V battery if 230V mains is available, as mains power has priority. Additionally, the 12V battery only operates correctly when the engine is running to avoid draining the vehicle battery. For safety, the AES system waits 15 minutes after the engine stops before switching to liquefied gas, preventing accidental switching at gas stations. If you wish to force battery operation while driving, refer to the section "Manual Energy Selection" in the manual, which explains how to switch from automatic mode to manual control of power sources.

Q: Why won't my DOMETIC RMS 8551 start in gas mode?

Mandatory preliminary checks Before any manipulation , ensure that: The gas bottle valve is open The gas shut-off valve of the refrigerator is open The refrigerator is properly powered (12V DC or 230V AC) - this is necessary for the igniter to work, even in gas mode If these elements are not in place, the device will never start in gas mode. Energy selector checks Depending on your RMS 8551 model (rotary selector or buttons), explicitly set the mode to “Gas” . Then press the battery ignition button . You should hear a clicking sound (igniter) for a few seconds and see the flame ignite in the combustion chamber. Technical checkpoints Flame indicator - Check that the flame indicator gauge shows a flame presence. If no flame appears, the igniter is not working or gas is not reaching. Gas pipe - Visually check that the gas supply pipe is not bent, crushed, or damaged. Safety shut-off - The device automatically stops the gas supply after about 30 seconds if the flame goes out. This is a normal safety system. If the problem persists If the igniter does not click at all, the igniter battery is likely depleted. If the igniter works (clicking sound) but no flame appears, gas is not reaching or there is a flow issue. In these cases, professional repair is recommended.

Question 1

Can this refrigerator operate on gas?

Accepted Answer

No, the DOMETIC RCD 10.5T cannot operate on gas. It is a compressor refrigerator that operates exclusively on electricity.

The power specifications for this model are:

Connection voltage: 12 V DC
Average power consumption: 54 W
Energy consumption: 0.70 kWh per 24 hours

This refrigerator is designed for use with direct current (typically powered by a battery, a solar panel with an inverter, or a stabilized external 12 V power supply). There is no gas operation option for this model.

Question 2

How do I set the temperature of the DOMETIC DM50CF refrigerator?

Accepted Answer

The DOMETIC DM50CF refrigerator has three temperature levels: 4°C (39°F), 7°C (45°F), and 12°C (54°F).

Steps to change the temperature:

Press and hold the adjustment button for 3 seconds until the interior light starts to blink
Press the button again immediately

The number of blinks of the light indicates the selected temperature:

5 blinks = 4°C (the coldest, ideal for quick freezing)
3 blinks = 7°C (default setting at 25°C ambient)
1 blink = 12°C (the least cold, for light preservation)

The temperatures cycle in this order: 4°C → 7°C → 12°C → then start over in a loop. The manual recommends selecting the middle level (7°C) and adjusting according to the quantity and type of food stored to avoid spoilage.

Question 3

Is it normal for the refrigerator compressor to be hot and the fan to be running?

Accepted Answer

Yes, this is completely normal. The DOMETIC RC 10.4T 70 is designed for the refrigeration unit (compressor and condenser) located at the back to become very hot during operation. This is the natural and intended operation of the refrigerator. The heat generated is dissipated by the external ventilation fan, which runs precisely to cool the unit and prevent dangerous overheating.

The behavior you observe depends on the selected operating mode: in Performance mode, the compressor and fan run at high speed, generating more heat and noise (about 42 dB); in Quiet mode, they operate at low speed for less noise (39 dB); in Boost mode, they run at high speed for maximum cooling. The lower the temperature setting or the hotter it is around the refrigerator, the harder the compressor works and the more heat is generated.

To check that your refrigerator is functioning correctly, ensure that: the internal temperature gradually decreases after starting; the compressor (blue snowflake on the screen) stops once the desired temperature is reached; air circulates freely around the refrigerator without blockage of the rear ventilation grilles; the refrigerator is at least a few centimeters away from walls or objects to allow heat dissipation.

It is normal and expected for the refrigeration unit to be hot to the touch: do not touch the heat-conducting parts at the back to avoid burns. Ensure that heat can dissipate properly; otherwise, the refrigerator may go into thermal protection. If an error code is displayed on the screen (for example, E34 for compressor overload), contact an authorized Dometic service center.

Question 4

Where is the temperature probe of the refrigerator located exactly?

Accepted Answer

The manual for the DOMETIC RC 10.4T 70 does not specify the exact location of the temperature probe on the product itself. The manual only mentions that a temperature sensor ensures the thermal regulation of the refrigerator compartment.

According to the available documentation:

The probe monitors the temperature of the refrigerating compartment (as indicated by error code W02 if it is defective)
It is integrated into the thermal regulation system of the model
If you suspect a malfunction of the sensor (for example, temperature stuck at 12°C), this is generally handled by an authorized DOMETIC professional

To locate the probe precisely or to perform a replacement, contact an authorized DOMETIC service, as these internal repairs are only recommended for qualified personnel.

Question 5

The refrigerator temperature is stuck at 12 degrees, how do I adjust the thermostat?

Accepted Answer

If the temperature is stuck at 12°C without an error code, it generally indicates a thermostat setting issue or a malfunctioning regulation. Here’s how to proceed:

Checking and adjusting the thermostat

The thermostat of the RC 10.4T 70 should be set between 2°C and 8°C for normal operation. Check that you have not intentionally set it to an intermediate level.
Press the control button for 2 seconds to restart the device. It will resume the last selected settings.
Check the operating mode: make sure you are in PERFORMANCE Mode or SILENT Mode (not in BOOST Mode where the thermostat is set to maximum).

If the problem persists

If the temperature remains at 12°C after these steps, the temperature sensor (thermal probe) may be defective. Although you do not have an error code displayed, a faulty sensor can keep the device at an intermediate temperature. In this case, contact the manufacturer DOMETIC for a diagnosis or replacement of the sensor.

Question 6

What does the flashing orange light on the DOMETIC CRE 50E refrigerator mean?

Accepted Answer

The flashing orange light on the DOMETIC CRE 50E refrigerator is a fault indicator of the system. The number of pulses (rapid flashes) indicates the nature of the problem according to the following error codes:

1 pulse: Abnormal power supply voltage (out of operating range)
2 pulses: Fan overcurrent (greater than 1 A)
3 pulses: Compressor or fan restarts too frequently in a short period
4 pulses: Abnormal rotor speed (rotor stuck or jammed)
5 pulses: Excessive differential pressure in the refrigerant system (greater than 5 bar)
Rapid continuous flashing: Temperature sensor fault

If you observe this orange flashing, start by turning off the refrigerator by pressing the power button, then disconnect the appliance from its power supply for at least one minute. Then plug it back in and turn it on normally. This procedure resets the system and may resolve some temporary faults.

If the orange light persists after this reset, or if you identify the specific error code (number of pulses), contact an authorized DOMETIC technician for a thorough diagnosis. The problem may require technical intervention depending on the nature of the detected code.

Question 7

What does error code Fehler 8 mean on the DOMETIC RMS 10.5XT?

Accepted Answer

Fehler 8 (E08) means No cooling power in 230 V operating mode (AC mode). The refrigerator is running on mains power but not cooling properly. This error code indicates a problem affecting the cooling power specifically in mains mode, distinct from a total lack of operation.

Troubleshooting steps:

Check the leveling of the appliance: This step is fundamental. Ensure that the refrigerator is level (not tilted forward and backward or sideways). Use a level if necessary. A poorly positioned appliance has reduced cooling power. This check should be done as a priority.
Check the ventilation: Make sure that the ventilation grilles are not blocked by debris, dust, or objects. Clean the external ventilation grilles if they are dirty. Insufficient ventilation significantly reduces cooling power.
Check the refrigerator door: Ensure that the door closes properly and that the seal is not damaged or misaligned. A poorly closing door allows warm air to escape and reduces cooling power.
Check the winter covers: In 230 V mode, both winter covers (if installed) must be in place to prevent heat buildup. Check that they are not partially detached.
Reset the error: Once the checks are completed, press and hold the control button for 2 seconds to reset the error code. The refrigerator will continue to operate in 230 V mode.
Contact customer service: If the error reappears after these checks and the appliance is properly leveled with clear ventilation, there may be a technical issue (faulty AC heating element or internal malfunction of the cooling system). Contact an authorized Dometic service center.

Important note: Unlike gas or 12 V DC modes, operation in 230 V (AC mode) heavily depends on the horizontal leveling of the appliance. If the motorhome or caravan is parked on sloped ground, this is often the cause of a loss of cooling power in mains mode.

Question 8

Does the refrigerator automatically switch to 12V battery power while driving?

Accepted Answer

The DOMETIC RM 8405 uses an AES (Automatic Energy Selection) system that automatically selects the available power source according to the following priority order:

Solar panels (if available)
230V AC mains
12V vehicle battery
Liquefied gas (last resort)

Important: The system does NOT automatically switch TO the 12V battery if 230V mains is available, as mains power has priority. Additionally, the 12V battery only operates correctly when the engine is running to avoid draining the vehicle battery.

For safety, the AES system waits 15 minutes after the engine stops before switching to liquefied gas, preventing accidental switching at gas stations.

If you wish to force battery operation while driving, refer to the section "Manual Energy Selection" in the manual, which explains how to switch from automatic mode to manual control of power sources.

Question 9

How to connect the DOMETIC RML 9435 to 12V DC and 230V AC?

Accepted Answer

The DOMETIC RML 9435 refrigerator can operate on three power sources: 230V AC, 12V DC, and gas. Here are the electrical connection instructions taken from the manual.

Connection 230V AC (alternating current)

Use exclusively the appropriate connection cable provided with the device.
Plug into a standard power outlet 230V~ / 50 Hz.
Ensure that the voltage of your installation matches that indicated on the device's nameplate.
To disconnect, always grasp the plug - never pull on the cable.
Power consumption: 170 W - Consumption: 3.2 kWh/24h

Connection 12V DC (direct current)

The 12V DC must be used only with the engine running, when the alternator provides sufficient voltage.
Alternatively, you can use a battery protector to prevent complete discharge.
Do not use the 12V mode with the engine off: you risk completely discharging the vehicle's battery.
Power consumption: 170 W - Consumption: 340 Ah/24h (to be considered for sizing your installation)

The detailed wiring diagram (terminal numbers, wire colors) is available in the PDF manual accessible from this page.

Question 10

Why won't my DOMETIC RMS 8551 start in gas mode?

Accepted Answer

Mandatory preliminary checks

Before any manipulation, ensure that:

The gas bottle valve is open
The gas shut-off valve of the refrigerator is open
The refrigerator is properly powered (12V DC or 230V AC) - this is necessary for the igniter to work, even in gas mode

If these elements are not in place, the device will never start in gas mode.

Energy selector checks

Depending on your RMS 8551 model (rotary selector or buttons), explicitly set the mode to “Gas”. Then press the battery ignition button. You should hear a clicking sound (igniter) for a few seconds and see the flame ignite in the combustion chamber.

Technical checkpoints

Flame indicator - Check that the flame indicator gauge shows a flame presence. If no flame appears, the igniter is not working or gas is not reaching.
Gas pipe - Visually check that the gas supply pipe is not bent, crushed, or damaged.
Safety shut-off - The device automatically stops the gas supply after about 30 seconds if the flame goes out. This is a normal safety system.

If the problem persists

If the igniter does not click at all, the igniter battery is likely depleted. If the igniter works (clicking sound) but no flame appears, gas is not reaching or there is a flow issue. In these cases, professional repair is recommended.

User manual DOMETIC Fridge : user manuals and guides in PDF

Models DOMETIC Fridge most viewed

Other categories DOMETIC

Recent questions about Fridge DOMETIC