GZ 121 - Ice machine Guzzanti - Free user manual and instructions

Product Type	Ice Machine
Brand	Guzzanti
Model	GZ 121
Ice Cube Type	Bullet Ice
Ice Production Capacity	Up to 12 kg per 24 hours
Water Tank Capacity	2.2 L
Ice Storage Capacity	0.6 kg
Compressor Type	Hermetic, R600a refrigerant
Cooling System	Air-cooled condenser
Power Supply	220-240 V, 50 Hz
Power Consumption	150 W
Noise Level	< 45 dB
Dimensions (W x D x H)	290 x 360 x 380 mm
Net Weight	10.5 kg
Control Type	Electromechanical
Indicator Lights	Power, Ice Full, Water Shortage
Cleaning Mode	Recommended every 3 months
Material	Stainless steel and ABS plastic
Safety Features	Automatic shut-off when ice full or water low
Accessories Included	Ice scoop, drip tray, user manual
Repairability	Spare parts available via authorized service

Frequently Asked Questions - GZ 121 Guzzanti

How do I clean the GZ 121 ice machine?

Unplug the unit and remove any ice. Mix a solution of warm water and mild detergent. Wipe down the interior and water tank. Rinse thoroughly. Run a cleaning cycle if available. Descale every 3 months.

Why is my ice not forming?

Check if the water tank is filled to the MAX line. Ensure the ambient temperature is between 10°C and 35°C. The compressor may need time to cool down. Clean the condenser coils if dusty.

How long does it take to produce first batch of ice?

Approximately 6-8 minutes after first power on, depending on ambient and water temperature.

Can I use tap water?

Yes, but for better taste and to reduce scale, use filtered or distilled water. Hard water may require more frequent descaling.

How do I store the ice machine when not in use?

Empty the water tank, dry all parts, and store in a cool dry place. Leave the lid slightly open to prevent mold.

What should I do if the 'Ice Full' indicator is on but the basket is empty?

The sensor may be blocked. Turn off the machine, remove the ice basket, and check for any obstruction. Clean the sensor with a soft cloth.

Is the GZ 121 noisy during operation?

It operates at under 45 dB, similar to a refrigerator. Some sounds from water flow and compressor are normal.

What is the warranty period?

Check your purchase documentation. Typically 2 years for household use, covering manufacturing defects.

Can I make different sizes of ice?

No, the GZ 121 produces fixed bullet-shaped ice cubes, about 2.5 cm in diameter.

How do I reset the machine after an error?

Unplug the unit for 5 minutes, then plug back in. If error persists, consult the manual or contact support.

USER MANUAL GZ 121 Guzzanti

Line drawing of a small electronic device with a control panel and display (no text or symbols)

Návod k obsluze

Návod na obsluhu

Instrukcja obsługi

Használati útmutató

Navodila za uporabo

Gebrauchsanleitung

Instruction manual

Symbol of a trash bin crossed with no text or numbers, representing waste sorting or restriction (no text present)

Symbol of a trash bin crossed with no text or numbers, representing waste sorting or disposal (no text present)

III. ZASADY BEZPIECZEŃSTWA

Symbol of a trash bin crossed with two diagonal lines, representing no waste or discharge (no text or labels)

Symbol of a trash bin crossed with no text or numbers, representing waste sorting or restriction (no text present)

III. VARNOSTNI NAPOTKI

Opis tipk in funkci j:

(1) Tipka ON/OFF/Stand-by
(2) Indikator ICE FULL (polna posoda za led)
(3) Indikator ADD WATER (dolijte vodo)
(4) Indikator WORK (delovanje)

DELOVANJE:

Symbol of a trash bin crossed with no text or numbers, representing environmental protection (no text present)

Symbol of a trash bin crossed with no text or numbers, representing waste sorting or disposal (no text present)

Important Safety Instructions: read carefully and keep for future reference.

Thank you for buying our product. We hope you enjoy using the appliance. Make sure you have read and understand this manual before using. Please well keep this instruction manual.

BASIC INTRODUCTION

Ice maker is a professional product used to make ice cubes. With a luxurious appearance, mantiseptic internal material, it is suitable for long-term use. Automatic ice-making system works in high speed and always produces ice cubes in standard shape.

In order to keep the ice maker working efficiently and smoothly, please always follow our instructions.

I. PRODUCT FEATURES

1. Adopting compressor refrigerating technology, the ice maker produces cubes efficiently.
2. This appliance is intended to be used in household and similar applications such as:
   Staff kitchen areas in shops, offices and other working environments;
   Farm houses;
   By clients in hotels, motels and other residential type environments.
3. The ice making process can be viewed through the transparent window.
4. Push-button operation, LED indicators-lights indicate the various statuses.
5. Warning for "Low-water" and for "Full ice cube bucket". Just simply remove ice to continue process.

II. LIST OF MAIN PARTS:

1. Transparent window
2. Lid
3. Evaporator
4. Ice making box
5. Ice cube bucket
6. Operation panel
7. Air inlet
8. Water outlet
9. Power cord
10. Air outlet
11. Ice scoop

III. SAFETY PRECAUTIONS

1. Before use, always check that the mains voltage is the same as the voltage on the rating plate of the appliance.
2. Keep it away from sources of heat, direct sunlight, humidity. Do not use the appliance with wet hands. If the appliance is humid or wet, unplug it immediately.
3. Do not use this appliance in the immediate surroundings of a bath, a shower or a swimming pool.
4. Do not use the appliance if the main cable or the mains plug is damaged or defective. If the mains cable or the mains plug is damaged or defective, it must be replaced by the manufacturer or an authorized repair agent.
5. Disconnect the mains plug from the mains when the appliance is not in use, before assembly or dis-assembly and before cleaning and maintenance.
6. In order to ensure your children's safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.
7. Do not pull out the plug in the way of pulling the power cord, must hold the plug tightly and pull it out from the socket directly.
8. Ice maker is specially used to make ice cubes, do not use the appliance to refrigerate other food or beverages, or it will damage the system.
9. Do not store or use gasoline and other flammable substances near the ice maker. Do not use ice maker if has leakage of flammable gas, to avoid cause a fire.
10. Do not move the appliance while it is switched on, to avoid damaging the cooling system.

11. Please dispose the flammable gas of ice maker according to local regulations.

12. WARNING: fill with potable water only.

13. Do not overfill water as this may cause a hazard. Do not fill above the MAX or below MIN mark.
14. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
15. WARNING – Keep ventilation openings; leave at least 20 cm space near the air inlet and outlet of heat dissipation.
16. WARNING – Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
17. WARNING – Do not damage the refrigerant circuit.
18. This appliance is intended to be used in household and similar applications such as:
    Staff kitchen areas in shops, offices and other working environments;
    Farm houses and by clients in hotels, motels and other residential type environments;
    Catering and similar non-retail applications.
19. Do not try to repair the appliance on your own. Always contact only an authorized technician. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard.
20. The appliance is suitable for domestic use only.

CAUTION: Risk of overheating!

Keep the ventilation slots free!

If the heat generated by the operation is not properly dissipated, it can result in overheating and fire.

IV. PLACEMENT ENVIRONMENT

1. Place the appliance on a stable and flat surface.
2. Keep the appliance away from heat sources and direct sunlight, to avoid affecting the ice-making performance.
3. Keep the appliance in a well-ventilated place; leave at least 20cm space near the air inlet and outlet of heat dissipation.
4. Do not use the appliance when placed in too cold or too hot environment. If the environment temperature is lower than 5 degrees or over 43 degrees, will cause the machine have problems of making ice.
5. Do not use outdoors.

V. PREPARATION BEFORE USE

1. Clean the machine and its components before use.
2. The appliance needs to sit down for 30 minutes after moving, before switching the power on. Failure to follow this instruction might cause damage to your Ice Maker.
3. Pour the water into water storage box (Only allow the water conformed to drinking standard).

Caution!

Do not exceed the maximum mark (H-MAX) when you fill the water reservoir.

VI. OPERATION PANEL

Introduction of buttons and functions:

(1) ON/OFF/Stand-by button
(2) ICE FULL indicator light
(3) ADD WATER indicator light
(4) WORK indicator light

OPERATION:

Fit the plug into the wall socket, the WORK indicator light will flash and emit a short beeping sound, and now the appliance is ready for use.

• To switch on the appliance, press the ON/OFF/Stand-by button ✪. The WORK indicator light will keep display not flash. The appliance starts making ice cubes.
• Within 15 minutes, the appliance is at the correct temperature and the first ice cubes are ready. As long as the appliance is switched on, it will continue to produce 6 ice cubes every 9-13 minutes.
• Regarding look through the transparent window (1) to check whether the ice-cube making process is running smoothly.
• If the ice cube bucket is completely full with ice cubes the ICE FULL indicator light will be on and emits a short beeping sound.
  Take the ice cube bucket out of the appliance, store the ice cubes in a cool place and put the bucket back into the appliance. The ice cubes makers can be switched on again straight away to prepare a new batch of ice cubes.
• In the absence of water, the ADD WATER indicator light will be on and emit a short beeping sound. Fill the reservoir with water and press the button continue the process.
• If the ice cubes are left in the appliance they will gradually melt, the melted water will collect in the water reservoir and then the ice cubes maker will start to produce a new batch of ice cubes. The machine can be stopped at any time by pushing the button .When the ice cube maker is not being used for an extended period of time, empty the water out of the reservoir and unplug the appliance from the electric wall socket.
• To interrupt the process, press the ON/OFF/Stand-by button.
• Remove the mains plug from the wall socket. The display goes off.
• Allow the appliance to cool down completely.

VII. SELF-CLEANING MODE

The self-cleaning mode should be put into operation before you use your ice maker for the first time and/or if there has been a long period without use.

WORK, ICE FULL, ADD WATER indicators will be on at the same time when the ice maker is in self-cleaning mode.

Stage 1:

1) Add equal amount of water and vinegar (1:1) into water reservoir.
2) In the state of stand-by mode, keep pressing ON/OFF button at least 5 seconds to activate self-cleaning mode. Please note self-clean mode will automatically start after "Beep" sound.
3) During the self-cleaning mode, pump will draw water to the ice making box and evaporator coils, then ice making box rotates and pours the water into water reservoir. This cycle will repeat for 5 times.
4) Upon completion, the unit automatically changes to stand-by mode.

Stage 2:

1) Remove the drain cap and plug, then drain off the water, insert the plug and screw drain cap.
2) Add fresh water to the maximum permit water volume line.
3) In the state of stand-by mode, keep pressing ON/OFF button at least 5 seconds to activate self-cleaning mode again with the purpose of clean-out.
4) Upon completion of this final stage of the self-cleaning process, the unit automatically changes to stand-by mode. Proceed to drain the water from the internal reservoir by removing the drain cap and plug. Leave the upper lid open to allow it to air dry.

Please note that if there is a water shortage during self-cleaning mode, the until will automatically go into stand-by mode; if ice making box fail to turn over, ICE FULL and ADD WATER indicators will be on at the same time, you need to keep pressing ON/OFF button for more than 5 seconds to release self-clean mode to change for other operations.

VIII. CLEANING AND MAINTENANCE

Warning:

Before cleaning or maintenance, switch off the appliance, remove the mains plug from the wall socket and wait until the appliance has cooled down.

Do not leave water in the appliance for a long period to prevent the water from being contaminated. Use the valve on the water outlet to remove the excess water.

Caution:

1. Do not use aggressive or abrasive cleaning agents to clean the appliance.
2. Clean the outside of the appliance with a soft, damp cloth. Thoroughly dry the outside of the appliance with a clean, dry cloth.

3. Clean the inside of the appliance with a soft, damp cloth. Thoroughly dry the inside of the appliance with a clean, dry cloth.

4. Clean the ice cube scoop in soapy water or in the dishwasher. Rinse the ice cube scoop under running water. Thoroughly dry the ice cube scoop with a clean, dry cloth.

5. If the ice machine will be off use for a long time, you should unplug the appliance, drain off the water and dry the appliance with a clean cloth, store the ice maker in a clean place.

6. Regularly check the appliance for possible damage.

IX.TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION
POWER indicator does not illuminate.	Power source is not switched on.	1. Check if the power supply is appropriate.2. Check if the power cord is connected properly to unit and power supply.3. Internal components may be damaged. Maintenance Required-seek professional help.
ICE FULL indicator is lit.	1. Ice bucket full.2. Low-temperature protection (ambient temperature is lower than 5°C).	1. Automatic recovery after removal of ice cubes.2. Move the ice maker to a warmer place where the ambient temperature above 5°C.
ADD WATER indicator is lit.	Absence of water. 1. Fill the	drinkable water into ice maker and press buttoneliminate the failure.2. Water supply system or components may be damaged. Maintenance by a professional is required.
ICE FULL and ADD WATER indicators are both on.	Ice making box is in an incorrect position.	1. Check whether any foreign objects is stuck in the ice making box.2. Internal components may be damaged. Maintenance by a professional is required.
Not making ice or not performing well.	1. Heat output is blocked.2. Water temperature is too high.3. The ambient temperature is too high.4. Leakage of refrigerant.	1. Clean the dust of air inlet and outlet.2. Fill with room temperature water.3. Move the ice maker to a cool place.4. Refrigerating system may be damaged. Maintenance by a professional is required.
Abnormal noise. Fan	or pump is obstructed.	1. Set up the appliance in proper location.2. Maintenance by a professional is required.

X. TECHNICAL SPECIFICATIONS:

Model GUZZANTI-GZ121
Rated Voltage 220 - 240 V ~
Rated Frequency 50 Hz
Rated Current 0,8 A
Protective Class I
Refrigerant R600a

XI. RECYCLING (DISPOSAL OF THE PRODUCT AT THE END OF ITS LIFE)

Waste Electrical Products Should Not Be Disposed Of With Household Waste. Please Recycle Where Facilities Exist. Check With Your Local Authority For Recycling Advice.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT

Symbol of a trash bin crossed with no text or numbers, representing environmental protection (no text present)

This symbol on products or original documents means that used electric or electronic products must not be added to ordinary municipal waste. For proper disposal, renewal and recycling hand over these appliances to determined collection points. Alternatively, in some European Union states or other European countries you may return your appliances to the local retailer when buying an equivalent new appliance. Correct disposal of this product helps save valuable natural resources and prevents potential negative effects on the environment and human health, which could result from improper waste disposal. Ask your local authorities or collection facility for more details. In accordance with national regulations penalties may be imposed for the incorrect disposal of this type of waste.

For business entities in European Union states

If you want to dispose of electric or electronic appliances, ask your retailer or supplier for the necessary information.

Disposal in other countries outside the European Union.

This symbol is valid in the European Union. If you wish to dispose of this product, request the necessary information about the correct disposal method from the local council or from your retailer.