SBS-LCS-112 - Sling STEINBERG - Free user manual and instructions

Product type	Chain sling
Brand	Steinberg
Model	SBS-LCS-112
Load capacity (1 leg, angle 0-90°)	2 tons
Safety factor	4:1
Operating temperature	-40 °C to +200 °C
Maximum lifting angle	120°
Material	Heat-treated steel
Main components	Master ring, connecting link, chain, hook
Intended use	Lifting and handling loads
Usage precautions	Visual inspection before each use, do not twist or knot the chain, avoid shocks
Maintenance	Periodic lubrication, store dry
Periodic inspection	Before each use: cracks, deformations, wear
Discard criteria	Hook wear >10%, chain elongation >5%, cracks
Repairability	Not repairable, replace if defective
Standards	EN 818-4:2008, Grade 8

Frequently Asked Questions - SBS-LCS-112 STEINBERG

What is the load capacity of the SBS-LCS-112 sling?

The load capacity for one leg at angle 0-90° is 2 tons. For other configurations, refer to the load chart.

What is the maximum allowed lifting angle?

The maximum lifting angle is 120°. Beyond that, the sling may be partially overloaded.

In what temperature range can I use this sling?

The authorized temperature range is -40 °C to +200 °C. Above 200 °C, the capacity decreases.

How to check the condition of the sling before use?

Visually inspect the ring, hook and chain for cracks, deformations or wear. Check the hook opening and chain elongation.

Can I tie or twist the chain during use?

No, it is strictly forbidden to knot, twist or tangle the chain. This could damage the sling and reduce its capacity.

What to do if the hook has a crack?

In case of a crack, the sling must be discarded immediately. It is not repairable.

What is the safety factor of this sling?

The safety factor is 4:1, meaning the breaking load is four times the working load.

Can the sling be used in a corrosive environment?

No, use near chemicals or corrosive products is prohibited. Store it in a dry place.

How to maintain the sling?

Apply grease regularly to prevent oxidation and store it in a dry environment after use.

What protective equipment should the operator wear?

The operator must wear a safety helmet and protective shoes. Do not stand under the load.

USER MANUAL SBS-LCS-112 STEINBERG

This User Manual has been translated for your convenience using machine translation. Reasonable efforts have been made to provide an accurate translation; however, no automated translation is perfect nor is it intended to replace human translators. The official User Manual is the English version. Any discrepancies or differences created in the translation are not binding and have no legal effect for compliance or enforcement purposes. If any questions arise related to the accuracy of the information contained in the User Manual, please refer to the English version of those contents which is the official version.

Technical data

WLL tonnes Grade 8 Classic / EN 818-4 :2008
		90°	b a		A b
Product type:		1 leg	2 leg		4-leg
Usage method :		Straight	b) 0-45°a) 0-90°	b) 45-60°a) 90-120°	b) 0-45°a) 0-90°	b) 45-60°a) 90-120°
Load factor		1	1.41	1	2.1	1.5
Model	SBS-LCS-113	2 / / / /
	SBS-LCS-112	2 / / / /
	SBS-LCS-111	2 / / / /
	SBS-LCS-110	2 / / / /
	SBS-LCS-109	3.15 / / / /
	SBS-LCS-108	3.15 / / / /
	SBS-LCS-107	/ 1.6 1.12 / /
	SBS-LCS-106	/ 1.6 1.12 / /
	SBS-LCS-105	/ 2.8 2 / /
	SBS-LCS-104	/ 2.8 2 / /
	SBS-LCS-103	/ 6.7 4.75
	SBS-LCS-102	2 / / / /
Safety factor 4 :1. Working load limits are based upon equally loaded and disposed product chain legs.

Product consists of the main ring, connecting link, chain and hook. All accessories are heat treated and some of them paint coated.

Limitations on the use of the chain sling due to adverse environmental conditions or hazardous conditions. Any limitations on the use of the chain sling due to the following shall be given:

a) This product should be used in the environment where relative temperature does not exceed the -40 to +200^ . Any environment that exceeds this temperature span is not allowed.
b) The product should not be used near the heat sources, in humid rain, and where corrosive chemicals or products are present.
c) It is prohibited from knotting, entangling, twisting chains and buckles.
d) The product should be used vertically only.
e) Multi-chains should be used within the prescribed angle. Do not use out of angle - see the table above.

Precautions before use

a) The product needs to be checked before use, such as rigging load, rigging length, chain diameter, inner length, inner width, hook opening size and other information or data on the nameplate.
b) The operator needs to have appropriate qualifications.
c) The operator must clearly see the working load and scope of application on the sign, overloading is strictly prohibited. Visual inspection of the product must be performed and it can be used only after compliance.
d) Under normal usage, the hoisting angle is the key to affecting the load. Max hoist angle must be within 120 degrees, otherwise chain sling will be partially overloaded.
e) It is forbidden to use informal connectors between the product.
f) It is forbidden to hang the load-bearing chain rigging directly on the components of the crane hook or wrap it around the hook.
g) When the product surrounds the hanging object, add padding at the corners to prevent the ring chain and the hanging object from being damaged.
h) Temperature has certain influence on the use of the product. When temperature is in the allowed range, the rated load is 90% of the given rated load. When the temperature is between 200 degrees and 300 degrees, it is 90% of the rated load. When it is between 400 degrees, it is 75% of the rated load.
i) Hoisting point of hook is required to be on the same vertical line as the center of gravity of the hoisting weight, so that the hoisting weight is in a stable and balanced state to prevent sliding or overturning during lifting.
j) Twisting, turning and knotting between the product is prohibited, and adjacent chain activities should be flexible.
k) When loading heavy objects, lifting-, lowering- and stopping-moves should be performed slowly and steady. Pay attention to the balance of the center of gravity of the objects to be lifted, avoid impact loads and do not hang heavy objects on the chain for a long time.
I) The product should be handled with care. It is strictly forbidden to beat, touch and drag it on the ground. It is necessary to prevent falling from a height to avoid deformation of the chain, surface and internal damage.
m) Strictly forbidden to use the product in hot-dip galvanizing or a pickling tank!

4. Use instruction:

a) Diameter of ring of the product should be within opening size of the crane hook and the crane hook should have a safety pin.
b) Connect the product ring with the crane hook.
c) Chain sling is prohibited from twisting and knotting during use, to avoid collision. Thelifted load object should be padded to prevent damage;
d) It is strictly forbidden to rotate when loaded;
e) It is strictly forbidden to shake when loaded;
f) If size of the product is too long, adjustment hook can be used to adjust it;
g) It is strictly forbidden to impact the product when loaded;
h) Operator of the product should wear safety helmet, well-fitting protective shoes and not stand with objects attached to it.
i) Make sure the hook safety is fully clamped, leaving no gap;
j) Multi-chain need to checked for the bearing capacity in the parameter table and use it within permissible load;
k) When unloading the personnel should stay away;
I) After the load landed smoothly, open safety pin of the hook and separate the product hook from the load;
m) After product had been used for a while, apply grease to prevent oxidation of the surface of the chain, and store in dry environment.

Periodic inspection and requirements

The appearance of the product should be inspected for cracks, deformations and twists before each use. The product should not be used anymore and (non-repairable) replaced if one of the following phenomenon occurs:

a) Ring and Hook

• Cracks: check the dangerous section at the lower part of the hook and the section of the relief groove at the threaded part of the hook tail. If there is any crack, it should be scrapped.
  Height wear of dangerous section of the hook reaches 10% of original size;
  Opening is increased by 10% compared with the original size
• Torsional deformation exceeds 10^ ;
• Plastic deformation of dangerous section or hook neck;

b) Chain

• Chain undergoes plastic deformation and when the elongation reaches 5% of the original length;
• The wear between the chain rings and the contact parts between the chain ring and the end fittings is reduced to 80% of the original diameter; the wear of other parts is reduced to 90% of the original diameter;
  The dangerous section wear of the end fittings is reduced to 10% of the original size;

For the disposal of the device please consider and act according to the national and local rules and regulations.

CONTACT

expondo Polska sp. zo.o. sp.k.