PCJ-302 - Air jack MSW - Free user manual and instructions

Product Type	Pneumatic Car Jack
Brand	MSW
Model	PCJ-302
Load Capacity	3000 kg
Minimum Height	150 mm
Maximum Height	400 mm
Working Air Pressure	10 bar
Air Connection	G 1/4"
Dimensions (L x W x H)	520 x 260 x 150 mm
Weight	15.2 kg
Casters	No
Power Supply	Compressed air
Recommended Use	Vehicle lifting (body sill)
Required Floor Type	Hard, flat floor
Safety	Use jack stands to support the vehicle
Maintenance	Clean, dry compressed air; store indoors
Repairability	Do not disassemble; contact the manufacturer

Frequently Asked Questions - PCJ-302 MSW

What is the load capacity of the MSW PCJ-302 pneumatic jack?

The load capacity is 3000 kg. Do not exceed this capacity.

What air pressure is required to operate the jack?

The working air pressure is 10 bar. Use clean, dry compressed air.

Can I use the jack to support the vehicle during repairs?

No, the jack is only intended for lifting. Always use safety jack stands of adequate capacity to support the vehicle.

What are the minimum and maximum lifting heights?

Minimum height 150 mm, maximum height 400 mm.

How to assemble the pneumatic jack?

Route the pneumatic hose through the lower and upper parts, secure with bolts and nuts, then connect to the control system. Tighten without excessive force.

What to do if the jack does not rise?

Check the compressed air supply, pressure, and that the valves are properly open. If the problem persists, contact the manufacturer.

Can I use the jack on an inclined floor?

No, use only on a hard, flat, stable surface. Place chocks under the wheels that are not lifted.

How to lower the jack?

Open the left switch to release air. The jack then descends gradually.

What is the warranty and after-sales service?

The manufacturer is not responsible in case of unauthorized disassembly. Contact the dealer or manufacturer for repairs.

Can the jack be used for vehicles other than cars?

This jack is designed for passenger cars. For other uses, check compatibility.

USER MANUAL PCJ-302 MSW

This User Manual has been translated for your convenience using machine translation. Reasonable efforts have been made to provide an accurate translation; however, no automated translation is perfect nor is it intended to replace human translators. The official User Manual is the English version. Any discrepancies or differences created in the translation are not binding and have no legal effect for compliance or enforcement purposes. If any questions arise related to the accuracy of the information contained in the User Manual, please refer to the English version of those contents which is the official version.

Technical data

Parameter description	Parameter value
Product name	Pneumatic Car Jack
Model	MSW-PCJ-301	MSW-PCJ-302	MSW-PCJ-303
Load Capacity [kg]	3000
Minimum Height [mm]	150
Maximum Height [mm]	400
Working Air Pressure [bar]	10
Air Inlet size	G 1⁄4"
Wheels	Yes	No	Yes
Dimensions [Width x Depth x Height; mm]	1120 x 250 x 150	520 x 260 x 150	1120 x 250 x 150
Weight [kg]	15.75	15.2	15.24

IMPORTANT: Please read these instructions carefully before using your jack. Proper use and care of the jack will be helpful to assure you of continuous safe trouble-free problems.

Matters needing attention:

1. This lifting jack is only used in the process of rising and falling, and if to support the cart, please use the safety stands. This product can only be used for the skirt part of the car.
2. Please use it on relatively level, solid ground.
3. Please place a triangle block under the car dependency wheel.
4. The normal operating pressure is 10 bar.
5. Compressed air should be clean and contain no water.
6. There is no need to raise the balloon to the maximum, as long as it is to the desired height (such as to lift off the ground), that is to say, to close the ball valve switch, to stop gas supply, to cram the safety bracket, and then to work.
7. Remember that if the balloon rises to the maximum (stop to rise), immediately shut off the valve switch, and stop gas supply.
8. When used, the jack should take a position outside of center for 10–20cm, that is, the jack should be put under the car just a little.
9. The safety value has been set at 10 bar. If exceeded, the pressure will be automatically discouraged. If it doesn't work, please correct it again.
10. When not in use, it should be placed indoors and must not be placed outdoors. Please use the supplied accessories.
11. It is strictly prohibited to disassemble the jack balloon subject; otherwise, there will be consequences to bear. At the same time, the manufacturer is not responsible for after-sale service.

Instructions for use:

When inflated, the lifter rises, when deflated, the lifter descends.

1. To control the switch in the rod back, insert the compressed air in the right gas nozzle, and close the left switch.
2. Open the right ball valve switch, and when the gasbag rises, it can be used.
3. To lower the jack, please open the left switch.

Assembly

Main body

MSW-PCJ-301	MSW-PCJ-302	MSW-PCJ-303

Connecting rod bottom part

MSW-PCJ-301	MSW-PCJ-302	MSW-PCJ-303

Connecting rod upper part

MSW-PCJ-301	MSW-PCJ-302	MSW-PCJ-303

1. The pneumatic hose passes through the bottom part, which is secured to the bottom plate with four bolts and nuts.
2. First, pass the pneumatic hose through the upper part and place the pneumatic connector nut onto the pipe port; then insert the pneumatic hose into the pneumatic control system and tighten the nuts (do not apply excessive force); finally, connect the spindles with bolts.

		Weight must be supported by a set of jack stands rated at the proper capacity before any work or inspection can be done on the vehicle. Do not exceed the rated capacity or loss of load may occur
		Always firmly apply parking brake
		This jack is designed for use on hard, level surfaces only. Use on uneven or unstable surfaces could result in instability and possible failure to support the load
		Place wheel chocks at the front and rear of the tires that will not be lifted before proceeding
		Always center the jack under the axle or a flat reinforced frame surface

Line drawing of a car with a numbered wheel and attached plug (no text or symbols)

For the disposal of the device please consider and act according to the national and local rules and regulations.

CONTACT

expondo Polska sp. z o.o. sp. k.