PDP-120 - Hammer MSW - Free user manual and instructions

USER MANUAL PDP-120 MSW

Parameter description Parameter value:
Product name POST DRIVER
Model MSW-PDP-120 (10051455)
Engine type	1-cylinder, 4-stroke petrol engine, air cooled
Fuel type	Unleaded petrol, min. 52 octanes
Fuel tank capacity [L]	0,08
Lubrication system capacity [L]	0,08
Motor oil type	API SE or higher SAE 10W30 (-15 + 40 °C) or 5W30 (below -15 °C)
Engine displacement [cm2]	37,7
Maximum torque [Nat] 1,9550 rpm
Fuel consumption [L/h] ≥10 566
Impact frequency [stroke/min]	900-1300
Impact energy [J] 25-50
Starter Pull starter
Maximum engine speed [rpm]	7900
Maximum engine power [kW]	1/6700 rpm
Acoustic pressure level [Pa [dB(A)]	94,6
Sound power level [Wb [dB(A)]	105,8
Dimensions [Width x Depth x Height/mm]	290x325x825
Weight [kg] 21,75
Spark plug type CM35H
Maximum tire diameter [mm]	120

1. GENERAL DESCRIPTION

The user manual is designed to assist in the safe and trouble-free use of the device. The product is designated and manufactured in accordance with strict technical guidelines, using state-of-the-art technologies and remanence. Additionally, it is produced in compliance with the most stringent quality standards.

DO NOT USE THE DEVICE UNLESS YOU HAVE THOROUGHLY READ AND UNDERSTOOD THIS USER MANUAL.

To increase the product life of the device and to ensure trouble-free operation, use it in accordance with this user manual and regularly perform maintenance tasks. The technical data and specifications in this user manual are up to date. The manufacturer reserves the right to make changes associated with quality improvement. The device is designed to take into account the emission risks to a minimum, taking into account technological progress and noise reduction opportunities.

LEGEND

The product satisfies the relevant safety standards.

Read instructions before use.

The product must be recycled.

WARNING OR CAUTION OR REMEMBER Applicable to the given situation (general warning sign.)

Use ear protection. Exposure to loud noise may result in hearing loss.

Wear head and face protection

ATTENTION! Lead noise

Wear foot protection.

Wear protective clothing.

WARNING! Toxic substances, danger of poisoning!

ATTENION! Fire hazard - flammable material!

ATTENTION: The surface, risk of burnout

PLEASE NOTE! Drawings in this manual are for illustration purposes only and in some details may differ from the actual product.

The original operation manual is written in German. Other language versions are translations from the German.

2.USAGE SAFETY

ATTENTION! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in serious injury or even

The terms 'device' or 'product' are used in the warnings and instructions to refer to POST DRIVER.

Prevent the device from getting wet. Risk of electric shock! Do not cover air inlets / outlets. Do not put your hands or office items inside the device while it is in use! Do not cover the ventilation openings!

2.1.SAFETY IN THE WORKPLACE

a) Do not use the device in a potentially explosive environment, for example in the presence of flammable liquids, gases or dust. The device generates sparks which may injure dust or fumes.
b) If you discover damage or irregular operation, immediately switch the device off and report it to a supervisor without delay.
c) If there are any doubts as to the correct operation of the device, contact the manufacturer's support service.
e) Only the manufacturer's service point may repair the device. Do not attempt any repairs independently!
e) Children or unauthorised persons are forbidden to use the device. The construction must result in loss of control over the device).
f Use the device in a well-ventilated space.
G Please keep this manual available for future reference. It may be used by a third party, the manual must be passed on with it.
h) Keep packaging elements and small assembly parts in a place that are available to children.
1) Keep the device away from children and animals. 2) Avoid touching the device with the hands or other objects.
1) This device is used together with an atomotet equipment, drawing instructions for use shall also be followed.

REMEMBER! When using the device, protect children and other bystanders.

2.2.PERSONAL SAFETY

a) Do not use the device when tired, ill or under the influence of alcohol, narcotics or medication which can significantly impair the ability to operate the device.
b) The machine may be operated by physically fit persons who are able to handle the machine, are properly trained, who have reviewed this operating method and have received training in occupational health and safety.
c) The device can be handled only by physically fit persons who are capable of handling it, properly trained, familiar with this manual and trained within the scope of occupational health and safety.
When working with the device, use common sense and stay alert. Temporary loss of concentration while using the device may lead to serious injuries.
r) The personal protective equipment as required for working with the device, specified in section 1 (Legend). The use of correct and improved personal protective equipment reduces the risk of injury.
1) Do not overestimate your abilities. When using the device, keep your balance and remain stable at all times. This will ensure better control over the device in unexpected situations.
g) Do not wear loose clothing or jewellery. Keep hair, clothes and gloves away from moving parts. Loose clothing, jewellery or long hair may get caught in moving parts.
b) The eye, nose and respiratory protection. i) The safety of the device. ii) The safety of the supervisor in ensure that they do not play with the device.

2.3.SAFE DEVICE USE

a) Do not overload the device. Use the appropriate tools for the giver task. A correctly-selected device will perform the task for which it was designed better and in a safer manner.
b) When not in use, store in a safe place, away from children and people not familiar with the device who have not read the user manual. The device may pose a hazard in the hands of inexperienced users.
c) Keep the device in perfect technical condition. Before each use check for general damage and especially check for cracked parts or elements and for any other conditions which may impact the safe operation of the device. If damage is discovered, hand over the device for repair before use.
d) Keep the device out of the reach of children.
e) Device repair or maintenance should be carried out by qualified technicians only using original spare parts. This will ensure safe use.
f) To ensure the operational integrity of the device, do not remove factory-fitted guards and do not loosen any screws.
(ii) When transporting and handling the device between the warehouse and the destination, observe the occupational health and safety principles for manual transport operations which apply in the country where the device will be used. Empyce the fuel from the tank before transportation.
h) Avoid situations where the device stops working during use due to excessive loading. This may result in overheating of the drive elements and damage to the device.
1) Do not leave this appliance unattended while it is in use.
j Clear the device regularly to prevent stubborn grime from accumulating.
k) The specified vibrations emission was measured using standard measurement methods. Vibrations emissions may change if the device is used in different surroundings.
I) Do not work on two workpieces at the same time.
II) Do not cover the air intake and outlet.
n) The device is not a toy. Cleaning and maintenance may not be carried out by children without supervision by an adult person.
a) It is forbidden to interfere with the structure of the device in order to change its parameters or to use it.
p) Keep the device away from sources of fire and heat.
q) Do not overload the device.
r) The average speed during operation. Avoid sudden acceleration or deceleration of the machine. a) The average speed during operation.
ATTENTION Despite the safe design of the device and its protective features, and despite the use of additional elements protecting the operator, there is still a slight risk of accident or injury when using the device. Stay alert and use common sense when using the device.

EN

EN

1. USE GUIDELINES

The device is intended for sticking vertical stakes into the ground with a maximum pole diameter of 120mm .

The user is liable for any damage resulting from unintended use of the device.

3.1. DEVICE DESCRIPTION

1. Air filter
2. Fuel tank cap
3. fuel tan
4. Throttle switch
5. Throttle cable
6. Camping spring
7. Muller
8. Ollner
   B. On/Off Cover
9. Inspection and lubricant application window
10. Handle
11. Pile driver housing
12. Piling nest
13. Stop switch
14. Adjustment switch
15. Drive train housing

3.2. PREPARING FOR USE

APPLIANCE LOCATION

The ambient temperature must not exceed 45^ and the relative humidity should not exceed 85% . Only use the device in well-ventilated areas. Do not obstruct the air outlet of the device. Keep the device away from any hot surfaces. The device should always be operated on a stable, fireproof surface and out of reach of children and persons with limited mental and/or sensory functions.

ASSEMBLING THE APPLIANCE

Before the first use (and also after every 10 operating hours) check the engine oil and, if necessary, top it up to a safe level. Pour the engine oil through the hole in the oil plug. In order to add oil or check its level, place the machine vertically cold or at least a dozen or so minutes after use). wait a while (if it was previously filled with oil), then uncrew the oil plug and check the level at the end of the scale. The correct level should reach at least the bottom of the graduation at the tip of the filler plug. If there is not enough oil, top it up so that its level is within the range on the filler plug. If the oil is used up (evidently dark colour and /or is less transparent)- be sure to replace it.

PLEASE NOTE: the maximum engine oil level should not exceed the lower edge of the end of the filling hole (see the picture below, thus not exceed the upper limit of the graduation at the tip of the oil plug. In the event of overflow, the excess can be sucked off through the filler opening.

A. Oil plug with level graduation
B. Oil fillet
C. Minimum engine oil level
D. Maximum engine oil level
PLEASE NOTE: to drive the machine, use only petrol (min. 92 octane) without any oil admixture!

3.3.DEVICE USE

3.3.1 STARTING THE MACHINE

After filling the tank with fuel and making sure that there is enough oil in the engine, before starting, press the transparent semi-circular fuel bubble several times (next to the choke lever) until the carburettor is filled with fuel. If you are starting the cold engine, turn the choice "ON" by pushing the choke lever down. If engine is warm, the choke should be turned off—the choke lever up ("OFF"). Holding the machine vertically with one hand, grasp the starter cord with the other and pull it vigorously when you feel resistance while pulling. Immediately after starting the engine, do not release the cord, but hold it to allow it to return to the initial position freely and smoothly. Let the running engine run idle for about 5 minutes to bring it up to operating temperature, and turn the choke off by pulling the lever upwards. PLEASE: Sometimes it may take several attempts of pulling the cord before the engine starts. In extremely cold ambient conditions, it may take longer for the engine to reach the operating temperature.

3.3.2 OPERATION

After warming up the engine and turning off the choke, you can start working. First, set the engine speed with the trigger on the handle, depending on the desired impact force. It is recommended to work at medium engine speed - working at high speed while not piling is strongly not recommended. PLEASE NOTE: when using the factory new device for the first time, it is recommended to work at low to maximum average speed for the first 20 hours in order to run in the engine, and thus extend its service life.

3.3.3 TURNING THE MACHINE OFF

Stop pilling, release the throttle trigger and allow the unit to continue idle for 3-5 minutes. Then, press the stop button lock to unlock it and move the stop button upwards according to the arrow marked on it.

PLEAES NOTE:If the device will not be used for some time, let it cool down completely and drain the remaining fuel from the tank.

3.3.4 DISMANTUNG THE PILING SOCKET

If you need to replace the piping/post driving socket (adapter), it is enough to unscrew the 4 hexagonal socket screws (use the Allen key) on the upper end of the socket and remove the socket from the device.

3.4.CLEANCING AND MAINTENANCE

a) Before each cleaning, adjustment, replacement of accessories and also when the device is not in use, let it cool down completely. Wait for the rotating elements to stop.
b) Use only non-corrosive cleaners to clean the surface.
c) Store the unit in a dry, cool place, free from moisture and dust.
d): Do not spray the device with a water jet or submerge it in water.
e) Do not allow water to get inside the device through vents in the housing of the device.
f Clean the vents with a brush and compressed air.
g) The device must be regularly inspected to check its technical efficiency and spot any damage.
h Use a soft cloth for cleaning.
I. Do not use sharp and/or metal objects for cleaning (e.g. a wire brush or a metal spatula, because they may damage the surface material of the appliance).

3.4.1 MAINTENANCE INTERVALS

This Table lists the standard intervals for service and maintenance of the machine under normal operation conditions. In the case of operation under harder conditions, e.g. cloudy surroundings, long hours of continuous operation, etc., service intervals are shorter.		Before work	After work or daily	After oil re-ill	Every week	Every month	When worn down	When required
Complete machine	Visual check (general condition, tightening screws)	√		√
	Cleaning v
Control handle/switches	Operation check v
Air liter	Cleaning v
	Replacement v
Fuel liter	Check v
	Replacement v
Fuel tank/fuel tank cap	Cleaning v
	Check v
	Tightening v
Gear/cylinder	Cleaning v
	Oil r-ill v
Vac r	Check v
	Removing accumulated dirt						√
Cylinder radiator	Check v
	Cleaning v
Spark plug	Check/setting the gap between electrodes					√
	Replacement v
Nuts and bolts	Check v
	Tightening v

3.4.2 AIR FILTER

Regularly check the condition of the air liter for contamination that could block it, thus reducing engine performance and its service life.

To get to the air liter, remove the plastic casing on the side of the machine by squeezing the two tails from the top of the casing (see pictures below). If the liter is dirty, remove it and wash it in warm water with a detergent (e.g. grey soap). Before reassembly, wipe it and dry it well. If the liter is damaged, replace it with a new one.

3.4.3 FUEL FILTER

If the fuel liter is blincked, the engine seep and impure energy of the machine will be reduced. To clean the liter, remove the rap from the tank, pull out the liter through the funnel and put it into a container. If the paper is not cleaned to clean the fuel, liter you should also clean the fuel tank.

3.4.4 SPARK PLUG

To ensure proper engine operation, the spark plug gap must be properly set (0.5-0.7 mm).

To get to the spark plug, I remove the machine housing by unscrewing the hexagonal socket screw located on top of the housing, and then pull the housing slightly upwards. Then, locate the ignition cable with a rubber L-shaped cap on one of its ends - after removing it, you will see the spark plug. In the case of a used spark plug, i.e., removed from the machine, before checking and possible adjustment of the gap, i.e., clean the flail accumulated on the tip of the spark plug with a wire brush. You can also use extraction petrol.

EN

3.4.5 MUFFLER

Regularly remove the dirt at the inlet and outlet of the muffer. You can also clean it with appropriate detergents. WARNING: Only clean the muffer when it is cold.

3.4.6 CYLINDER RADIATOR

Regularly remove the accumulated dust and other dirt from the cylinder cooling fins. The machine has an air-cooled engine, therefore unobstructed cylinder fins are crucial for its trouble free long-term operation.

3.4.7 LUBRICATION OF THE IMPACT CYLINDER After 50 hours of operation (pilling or past driving), lubricate the hammer cylinder. To do this, unscrew the lubricant inspection window and tap up approx. 50g transmission fluid:17-80W90 GL through the window. Regularly check the fluid level through the window.

3.4.8 ENGINE OIL

The condition of the oil influences the operation and life of the engine considerably. The engine oil must be replaced after the first use after 10 operating hours, then every 50

operating hours or every six months, whichever comes first. To replace the oil, prepare a right capacity special oil pump with a 10 inch diameter oil filter cap on the vertically positioned machine, and tilt it so that all the oil flows out through the filler opening.

PLEASE NOTE: warm oil is thinner and easier to drain, however, be careful and mind the hot parts of the device and the warm oil itself - there is a risk of burns.

DISPOSING OF USED DEVICES

Do not dispose of this device in municipal waste systems. Hand it over to an electric and electrical device recycling and collection point. Check the symbol on the product, instruction manual and packaging. The plastics used to construct the device can be recycled in accordance with their markings. By choosing to recycle you are making a significant contribution to the protection of our environment. Contact local authorities for information on your local recycling facility.

INSTRUKCJA OBSLUGI

DANE TECHNICZNE
1.DGOLNYOPIS

3.4.4 CANDELA DI ACCENSIONE

For the disposal of the device please consider and act according to the national and local rules and regulations.

CONTACT

expondo Polska sp. z o.o. sp. k.