Qi TPBQS 10000 A1 - Power bank TRONIC - Free user manual and instructions

USER MANUAL Qi TPBQS 10000 A1 TRONIC

indicates the potential threat of explosion. Failure to observe this warning may result in serious or fatal injuries and potential property damage. Follow the instructions in this warning to prevent serious injuries, a danger to life or property damage! This symbol means that the operating instructions must be observed before using the product. Direct current / voltage Technology to optimize charging time. The equipment complies Quick Charge 3.0 specifications and agreements issued by Qualcomm Technologies, Inc.GB/IE 34 “Qi“ and the Qi logo mark are trademark of the Wireless Power Consortium (WPC) PD: Power Delivery (PD), introducted by the USB Implementers Forum, Inc., is a specification for handling higher power and allows a range of devices to charge quickly over a USB connection. It operates by facilitating a conversation between two devices so they can determine how much power can be pulled from the charger. CE mark indicates conformity with relevant EU directives applicable for this product.GB/IE 35

POWER BANK P Introduction We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it. P Intended use This QI

POWER BANK (hereinafter referred to as “product”) is an Information Technology device which is solely intended to be used to charge mobile devices which have Qi wireless charging technology. Devices that do not support Qi wireless technology can be charged through a USB port. This product is not intended for commercial use. Manufacturer is not liable for damages, which result from non-intended use. P Trademark notice ‒ USB

is a registered trademark of USB Implementers Forum, Inc. ‒ “Qi“ and the Qi logo mark are trademark of the Wireless Power Consortium (WPC). ‒ The TRONIC trademark and trade name is the property of their respective owners. ‒ The Smart Fast Charge trademark and trade name is the property of their respective owners.GB/IE 36 ‒ Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. Qualcomm Quick Charge is a trademark of Qualcomm Incorporated. All Qualcomm Incorporated trademarks are used under license. ‒ Any other names and products may be trademarks or registered trademarks of their respective owners. P Scope of delivery 1 Qi

Power bank 1 USB type A to USB type C cable 1 Instructions for use P Parts description Please refer to the fold out page.

USB Type A to Type C cable

Transmitted maximum radio frequency power (H-field): -9.5dBuA/m at 10m distance Maximum output power: 15 W* Maximum output current: 3 A* Minimum output current: approx. 100 mA Operating temperature: 5 – 35 °C Storage temperature: 0 – 45 °C Humidity (no condensation): 10 –70 % Dimensions: approx. 138 x 69 x 18 mm Weight: approx. 245 g *If all outputs are used at the same time, the sum of the output current must not exceed 3 A (5V 3A, 15W).GB/IE 38 Notes on Qi technology: This product with Qi wireless charging is designed to comply with the Qi (Wireless Power Consortium) standard, but no guarantees are given for its compatibility with all products that comply with the standard. Safety notices Please familiarise yourself with all instructions for use and safety notices before using the product for the first time. When passing this product on to third parties, please be sure to include all documentation. Check the product for visible external damage before use. Do not use the product if damaged or dropped. This product may be used by children age 8 years and up, as well as by persons with physical, sensory or mental impairments or lacking experience and/or knowledge, provided they are supervised or instructed in the safe use of the product and understand the associated risks. Do not allow children to play with the product. Never allow children to clean or maintain this product unsupervised.

DANGER! Packaging materials are not a toy. Keep all packaging materials out of the reach of children. Suffocation hazard! Always use the product on flat and smooth surface. The product could be damaged if it falls. Do not expose the product to direct sunlight or high temperatures. It may otherwise overheat and be damaged beyond repair. Do not operate the product near heat sources such as radiators or other devices producing heat. Do not operate the product near open flames.GB/IE 39 The product is not designed for use in rooms with high temperatures or humidity (i.e bathrooms) or those in which a great amount of dust is generated. Do not expose the product to dripping water or splashing water and do not place containers filled with liquids such as vases or open drinks on top of or beside the product. Do not expose the product to extremely high temperatures. This applies in particular if you are thinking about storing the product in your car. Over a prolonged period of time, the car and the glove compartment could become extremely hot. Remove electric and electronic devices from the car. Do not use the product immediately after it has brought from a cold room to a warm room. Allow the product to acclimatise before you switch it on.

WARNING! Never open the product casing. This product has no internal parts requiring maintenance. Do not independently convert or modify the product. Repairs to the product must be performed by authorised specialised companies or customer service. Improper repairs may place the user in considerable danger. They will also void the warranty.

WARNING! Metal objects between the charger and device to be charged will get hot and can burn you. Remove foreign objects from the charger before charging device.

WARNING! EXPLOSION HAZARD! Improper handling of lithium polymer batteries can result in fire, explosions, hazardous substances leaking, or other dangerous situations! Do not throw the product into the fire, as this could lead to the built-in battery exploding. Observe the usage restrictions and prohibitions of use for battery-operated products in situations which may be hazardous such as at petrol stations, airports, hospitals, etc.

WARNING! During charging process, please be noticed that the product must not be covered. Otherwise the product can be heated.GB/IE 40 The product should never be charged at a PC or notebook, because due to the high power consumption, the PC or notebook could be damaged. NOTE: Do not attach a metal object to the Qi charging surface

Do not charge your device when the Qi charging surface

is covered with a towel, layer of dust, etc. Do not allow the Qi charging surface

to get wet from water, beverages, etc. Do not use the Qi charging surface

if it is malfunctioning. Immediately switch the product off and remove the charging cable from the product if you smell burning or see smoke. Have the product examined by a qualified technician before using it again. Do not subject the Qi charging surface

with a strong forces or impact. Failure to do so may result in damage, injury and/or malfunction. Do not place magnetic recording media inside the charging area during charging. The magnetism generated may erase the data on credit cards. It may also cause wristwatches and other precision instruments to malfunction. During charging and immediately after charging, the Qi charging surface

and mobile device will be warm. This is normal and not a malfunction. If there is an unusual heating, check the Qi charging surface

and mobile device. Always place only one mobile device to charge on the Qi charging surface

. Only one device can be charged at a time. Compatibility with all Qi devices cannot be guaranteed.GB/IE 41 Do not attach an anti-slip mat or stickers to the Qi charging surface. The presence of an anti-slip mat or stickers between the mobile device to be charged and the Qi charging surface

that may prevent charging start. If a cover or decorative accessory that does not comply with the Qi wireless power standard has been attached to the supported device, it may not be possible for the device to be charged depending on the material, thickness, etc. of the cover or accessory. In such cases, remove the attached cover or accessory. If charging does not start even after the supported device has been placed in the charging area, place the device near the center of the charging area. Before starting with wireless charging, read the instructions provided with the mobile device as well. If you use a USB power supply for charging the power bank, the socket used must always be easily accessible so that the USB power supply can be quickly removed from the socket in the case of emergency. Please also refer to the manufacturer‘s instruction manual. ATTENTION! Two Qi charging devices and/or power banks must never be placed on top of each other with the charging surface. A device defect is the possible consequence. P Before use NOTE: Remove all packaging materials from the product. Please also check the content of delivery inside the packaging to see if there are any damages. If you notice any damage or missing parts, please contact the dealer who sold this product.GB/IE 42 P Operation and use P Charging the power bank The built-in rechargeable battery must be fully charged before using the product. To charge the power bank

only use power supplies with an output voltage and current matching the rated input voltage and current as stated in “Technical specifications” of this user manual.

ATTENTION! The power bank should not be charged from a PC or notebook. In order to get the fastest charging speed, charge the power bank

using a USB Type C to Type C cable (not included) and a USB Power Delivery (PD) enabled power charger (not included). Connect the USB Type C plugs of your Type C to Type C cable (not included) to the PD port

and the PD port of your USB PD enable power charger (not included) (see fig. A). Alternatively, you could charge the power bank

using the included USB Type-A to Type C cable

with a conventional USB charger but the charging time will be longer. Connect the USB Type C plug of the USB cable

and connect the USB Type A plug of the USB cable

to the USB power supply (not included) (see fig. B). NOTE: The Qi wireless charging function of the power bank is disabled when the power bank is being charged.GB/IE 43 During the charging process, the battery status indicator

goes up and shows you the appropriate charge level of the internal battery via 4 LED lights as described below: Battery status indicator

Power bank battery status 1 LED flashes 0-25 % 1 LED illuminates 1 LED flashes 25-50 % 2 LED illuminate 1 LED flashes 50-75 % 3 LED illuminate 1 LED flashes 75-100 % 4 LED illuminate 100 % NOTE: The 4th LED light (next to the Qi status indicator

) will turn green when the power bank is charged via PD input port

using a PD-enabled USB charger. If a conventional USB charger is used for charging, the 4th LED will still be the original colour of the battery status indicator. ATTENTION! Do not connect any device to the power bank for charging while the power bank itself is charging. Remove the charging cable from the power bank when it is fully charged.GB/IE 44 P Checking the battery status You can check the battery status on the battery status indicator

at anytime. Briefly press the On/off button

shows the approximate charge status of the internal battery for approx. 30 seconds. Qi wireless charging Put your Qi compatible device to be charged on the centre of the Qi charging surface

Slightly adjust the charging position of the device to be charged so that its charging surface is facing down to the centre of the Qi charging surface

to switch on the power bank

. The wireless charging will then start automatically. When Qi charging is active, Qi status indicator

shows the current charge status of the internal battery throughout the wireless charging process. NOTE: If your device supports 10 W wireless charging, the 4th LED of the battery status indicator

will turn green. For wireless charging below 10 W, the LED will still be the original colour of the battery status indicator

If wireless charging does not start, move your device to be charged more accurately to the centre of the Qi charging surface

until the Qi status indicator

starts flashing. While in idle status (standby mode), the Qi status indicator

will go off if no Qi compatible device is detected and idle for approx. 30 seconds.GB/IE 45 When the charging process has finished (i.e. the mobile device is fully charged) the Qi status indicator

stop flashing and light blue. The Qi status indicator

will go off when errors are detected on the Qi charging surface

*. In this case, remove your device and make sure that there are no unwanted metallic objects between your device and the Qi charging surface

and then try again. To stop the wireless charging, take your device away from the Qi charging surface

will light blue (standby mode)*. If no Qi compatible device is detected for approx. 30 seconds, the Qi status indicator

will go off. To switch off the power bank

during the standby mode, press the On/off button

twice. The Qi status indicator

and battery status indicator

may change back to blue colour (standby mode) when wireless charging has finished if the mobile device closed the wireless communication between the Qi charging surface

and the mobile device.

2) All devices to be charged must comply with Qi Standard.

3) The different modes of the Qi status indicator are

Starting process (boot phase), standby or searching for a Qi charging device Light blue Charging Flash blueGB/IE 46 Qi wireless charging status Qi status indicator

Fully charged Light blue Fault/Error condition Indicator off No Qi compatible device detected Indicator on P Charging mobile devices with the power bank via the USB output ports You can charge up to two devices at the same time using the USB ports of the power bank

. If all outputs are used at the same time, the sum of the output current must not exceed 3.0 A. To charge your QuickCharge 3.0 enabled device, connect the USB type A plug of the USB cable

or the original charging cable of the device to be charged to the USB Type A (QC3.0) output

. Then connect the USB Type C plug of the USB cable

to the Type C input of device to be charged. The charging process will start automatically. NOTE: You could also charge your conventional USB devices from the USB Type A output port

using the included USB cable

or a USB Type A to micro USB cable (not included). To charge your USB Power Delivery (PD) enabled device, connect the USB Type C plugs of your USB Type C to Type C cable (not included) to the PD port

and the PD port of the device to be charged. The charging process will start automatically.GB/IE 47 In case if the charging process does not begin immediately, press the On/off button

briefly to begin the charging process. The current battery status of the power bank

displayed during the charging process by the battery status indicator

To end the charging process, disconnect the USB charging cable from the mobile device and the power bank

and the battery status indicator

will switch off after approx. 30 seconds. To switch off the power bank

after your mobile device is disconnected: press the On/off button

twice. The power bank

and the battery status indicator

1) If you use all the USB ports, a voltage of 5 V will output at

all the outputs. The maximum output current must not exceed 3 A for all outputs. If all USB outputs are used, fast charge mode will not be activated.

is in quick charge or PD mode, and another USB port is connected to another device for charging, the quick charge or PD mode will be terminated and switched to normal charge mode. All devices will now be charged at 5 V each. P Charging mobile devices wirelessly and via USB simultaneously You can charge up to three devices at the same time using the USB ports and the wireless charging function of the power bank

. If all outputs are used at the same time, the sum of the output current must not exceed 3 A. Follow the procedures under the section “Charging mobileGB/IE 48 devices with the power bank

via USB output ports” to charge your devices via USB. During the USB charging process, put a Qi compatible device on the Qi charging surface

to start the Qi wireless charging process. For the details of wireless charging operation, please refer to the section “Qi wireless charging”. To end the charging process, disconnect the USB charging cable or remove the device from the Qi charging surface

twice to switch off the power bank

NOTE: If all USB output ports and wireless charging are used simultaneously for charging devices, a voltage of 5 V will be output at all outputs. The maximum output current must not exceed 3 A for all outputs. P Troubleshooting = Problem = Cause = Solution It may not be possible to charge a Qi compatible device. The mobile device is already fully charged. Take away the fully charged device for use, until its internal battery was drained again. Then put device back to Qi charging surface

for charging. The mobile device has become very hot as a result of charging.GB/IE 49 Remove the mobile device from the Qi charging surface

for a few hours to let it cool down, and also check if your product was damaged. This product is in a location where strong radio waves or noise is being generated, such as TV towers, electric power plants, or gas stations. Under this environment, use other output ports, such as USB type C or type A ports for charging up your mobile device. The power bank

is not being charged. It may be that the power bank

is not connected properly. Check that it is connected. In order to charge the power bank

, use a power supply with an output voltage and curernt matching the rated input voltage and current as stated in “Technical specifications“ of this user manual. A connected device is not being charged. The battery is drained. Charge the battery. The device is not connected. The device is not connected. Check that it is connected. Briefly press the On/off button

to begin the charging process. The current consumption of the connected device might be too low. Check with your connected device manual and see if your connected device current consumption comply with thisGB/IE 50 product. The minimal output current of the power bank

approx. 100 mA. The power bank

does not react when the button is pressed or when a device is connected, even though the battery is charged. The power consumption of the connected devices is too high. Therefore, the internal overcurrent protection device was activated. Reduce the number of devices connected and press the On/off button

Wireless charging did not start Device to be charged is not placed at the centre of the Qi charging surface

Make sure your device to be charged is at the correct position at the centre of the Qi charging surface

Make sure that there are no other objects on the Qi charging surface

Remove your device‘s protective case as it may be blocking the wireless signal. Wireless charging speed slow Device to be charged is too far away from the centre of the Qi charging surface

Make sure your device to be charged is at the correct position at the centre of the Qi charging surface

.GB/IE 51 P Cleaning and care This product has no internal parts requiring maintenance. Moisture entering the product may result in damage. Do not wipe the Qi charging surface

with oils, alcohol, benzine, thinners, etc. or expose it to hair sprays, insecticide sprays, etc If the Qi charging surface

becomes dirty, wipe off the dirt using a clean damp cloth. Ensure no moisture enters the product during cleaning to prevent damaging the product beyond repair. Do not use abrasive, solvent-based or aggressive cleaners. These can damage the surface of the product. Only clean the product with a slightly damp cloth and mild washing-up liquid. P Storage during non-use Store the product in a dry dust-free location, protected from direct sunlight. If the product is not used for a long time, the built-in battery should be fully charged to prolong its operating life. Regularly charge the built-in battery if you do not use the product for a long period of time. This is necessary to preserve the battery.GB/IE 52 P Disposal Packaging: The packaging is made of environmentally friendly materials, which may be disposed of through your local recycling facilities. Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1 - 7: plastics / 20 - 22: paper and fibreboard / 80 - 98: composite materials. Product: Contact your local refuse disposal authority for more details of how to dispose of your worn-out product. The adjacent symbol of a crossed out dustbin on wheels indicates this product is subject to Directive 2012/19/EU. This directive states at the end of the life this product must not be disposed of through regular household refuse but must be returned to special collection sites, recycling depots or waste management companies. This disposal is free of charge to you. Protect the environment and dispose of properly. The product is recyclable, subject to extended manufacturer responsibility, and collected separately. an be obtained from your local authority. The built-in rechargeable battery cannot be removed for disposal. Return the product completely to a collection site for used electronics.GB/IE 53 P Simplified EU declaration of conformity Hereby, OWIM GmbH & Co. KG, Stiftsbergstraße 1, 74167 Neckarsulm, GERMANY, declares that the product QI

“WAARSCHUWING! GEVAAR VOOR

is ong. 100 mA. De powerbank

to gange for, at slukke for powerbanken