IAN 298812 - Lamp Livarno Lux - Free user manual and instructions

USER MANUAL IAN 298812 Livarno Lux

Dispose of the packaging and device in an environmentally-friendly manner! Observe the warnings and safety notices! LED Floor Lamp Introduction Congratulations on your new product. You have selected a high quality product. Please be sure to carefully read the com- plete operating instructions. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly in- stalled. Should you have any questions or you are unsure about operating the product, please contact the dealer or service centre. Please keep these in- structions in a safe place and pass them on third parties as applicable. Intended use This light is only suitable for indoor use in dry and enclosed spaces. This product is intended for private household use only. Scope of delivery Check immediately after unpacking that the parts are complete and that the product is in proper condition. 1 LED Floor lamp, model 14101902L or 14102002L 1 Base 1 Adjustment lever 1 Counterweight (model 14102002L) 1 Instructions for use13 GB/IE Introduction / SafetyIntroduction Parts description

Counterweight (model 14102002L)

Transportation lock Technical Data Model no.: 14101902L or 14102002L Operating voltage: 230–240 V∼, 50 Hz Illuminant: 2 LED modules, each approx. 5 Watts (LED module not replaceable) Protection class: II / Safety Safety information Damage due to failure to comply with these operat- ing instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions! Avoid the risk of fatal injury from electric shock Check the light for damage every time before you use it. Never use the light if it shows any signs of damage. A damaged light means danger of death from electric shock. In the event of damage, repairs or other problems with the light please contact the service centre or a qualified electrician. To prevent hazards, a damaged flexible outer lead on this lamp must be replaced by the man- ufacturer, its service representative or an equally qualified professional! Before use, verify the available mains voltage corresponds with the operating voltage of the lamp (see „Technical Data“). Ensure that the light does not come into contact with water or other liquids under any circum

stances. Always unplug from the mains before assembling, disassembling, cleaning, or if the lamp will not be used for extended periods. Never open any of the components of the elec- trical equipment or insert any objects into the same components. This will pose a risk of fatal injury from electric shock. The LED module in this light cannot be replaced; if the LED module has reached the end of its life, replace the entire light. This light is not suitable for dimmer or electronic switches. Prevent fire and injury hazards RISK OF INJURY! Check every illuminant for damage immediately upon unpacking. Do not install the light if the illuminants are defective. In this case contact the service centre for a replacement. Do not look directly into the illuminant (lamp, LED, etc.). Do not look into the illuminant (lamp, LED, etc.) with an optical instrument (e.g. magnifier). Do not leave the light or packaging material ly- ing unattended. Plastic film or bags, plastic parts etc. can turn into dangerous toys for children. Do not cover the lamp or the mains plug with objects. Excessive heat can result in a fire. Never leave the lamp unattended whilst in use.14 GB/IE Start-up / Maintenance and cleaning / Disposal / Warranty and serviceSafety / Preparation / Start-up Safe working Mount the light so that it is protected from mois- ture and dirt. Carefully prepare for assembly and allow your- self adequate time. Organise all parts and any necessary additional tools or materials before starting so they are easy to reach. Always be attentive! Always pay attention to what you are doing and use common sense. Never assemble the lamp if you are unfocused or feel unwell. In order to disconnect the lamp completely from the power supply, the mains plug must be removed from the socket. Preparation Required tools and material The tools and materials specified are not included. This information and these values are non-binding and are only provided as a reference. The nature of the material is determined by the individual local conditions. – Screwdriver Start-up Mounting the light Note: When assembling the stand tube

be sure not to damage the mains lead inside the lamp. Unfold the floor lamp. Remove the transport lock

from the support tube

Carefully pull the mains lead out of the stand tube

Be sure the cone 5 c is seated correctly. Tighten the retaining sleeve

to secure the stand tube

Screw the lower stand tube section 5 b clockwise into the base

Screw the adjustment lever

. You will need a small screwdriver to do this. Plug the mains plug

into a properly installed socket. Your light is now ready to use. Adjusting the height Unplug the mains plug

from the socket before adjusting the light. Loosen the retaining sleeve

Adjust the floor lamp to the desired height. Tighten the retaining sleeve

Note: Retighten the retaining sleeve

if it loosens and the lamp adjusts in height. Plug the mains plug

into the socket. Switching the lamp on / off Switch the lamp on or off using the ON / OFF switch

Adjusting the reflector Note: only change the position of the reflector

if the light is switched off. Allow the light to cool off completely. Turn the reflector

to the desired angle. Adjusting the lamp arm Note: only change the position of the lamp arm

if the light is switched off. Allow the light to cool completely. Model 14101902L: turn the lamp arm

the desired position. Model 14102002L: hold on to the lamp arm

to the desired position. Tighten the locking lever

.15 GB/IE Start-up / Maintenance and cleaning / Disposal / Warranty and serviceSafety / Preparation / Start-up Note: retighten the locking lever

moves out of position. Maintenance and cleaning

HOT SURFACES! Allow the lamp to cool down completely.

SHOCK! For electrical safety, never clean the light with water or other liquids, or immerse it in water. Do not use solvents, benzene or similar sub- stances. They could damage the light. Only use a dry, lint-free cloth for cleaning. Plug the mains plug

into the socket. Disposal The packaging is made entirely of recyclable mate- rials, which you may dispose of at local recycling facilities.