PAS 10 A2 - LED Lighting PARKSIDE - Free user manual and instructions

USER MANUAL PAS 10 A2 PARKSIDE

Dispose of the packaging and product in an environmentally-friendly manner! Intertek / GS tested Lights for harsh operating conditions Cable length: 3 m C159239 Packaging from responsible sources 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 21353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 21 24.03.21 11:3024.03.21 11:3022 GB/IE LED work spotlight 10 W PAS 10 A2 Introduction We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important informa- tion concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applica- tions. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it. Intended use This light is suitable for indoor and outdoor use and is not intended for use as a hand-held lamp. This product withstands extreme physical con- ditions in the form of shocks (1.0 m

/ s³ 200–2000 Hz) and is also suitable for harsh conditions. This product is only intended for private household use. Any use other than that described or any product modi-

ication is prohibited and will result in damage. The manufacturer assu mes no liability for damages due to improper use. This product is not intended for commercial use. The product is not suitable for use as residential room lighting. 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 22353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 22 24.03.21 11:3024.03.21 11:3023 GB/IE Parts description

Fixture for tripod installation

Fixture for wall installation Technical data Model number: FCL-76003LI Operating voltage: 220–240 V∼ 50 Hz Illuminant: LED module (not replaceable) Power input: 10 W Luminous flux: 1000 lm (Φ 120 °: 910 lm) Colour temperature (light colour): 6500 K (Daylight white) Beam angle: 110 ° Maximum installation height: 2.5 m Maximum projected area: approx.: 28 m² (3.5 x 8 m) Protection type: product: IP65 (protected from water jets) plug: IP44 (protected from water spray) Protection class: I / Cable length: 3 m Dimensions: 20 x 16.5 x 5 cm (including bracket) 10 x 12 x 4.6 cm (lamp only, without bracket) Weight: approx. 955 g 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 23353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 23 24.03.21 11:3024.03.21 11:3024 GB/IE Scope of delivery Always check that all the parts are present and that the product is in perfect condition immediately after unpacking. 1 LED floodlight 1 Instructions for use General safety notes BEFORE USING THIS PRODUCT, PLEASE FAMILIARISE YOURSELF WITH ALL OF THE SAFETY NOTES AND INSTRUCTIONS FOR USE! PLEASE ALSO INCLUDE ALL DOCUMENTATION WHEN PASSING THIS PRODUCT ON TO OTHERS!

DANGER TO LIFE AND RISK

OF ACCIDENTS FOR INFANTS AND CHILDREN! Never leave children unsupervised with the packaging material. The packaging material poses a suffocation hazard. Chil- dren frequently underestimate the dangers. Always keep children away from the product. This product may be used by children aged 8 years and up, as well as by persons with reduced physical, sensory or mental capacities, or those lacking experience and/or knowledge, as long as they are supervised or instructed in the safe use of the product and they understand the associated risks. Do not allow children to play with the product. Never allow children to clean or maintain this product unsupervised. The LED module cannot be replaced. If the LED module fails at the end of its service life, the entire product must be replaced. 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 24353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 24 24.03.21 11:3024.03.21 11:3025 GB/IE This product‘s mains cable is non-replaceable. If the mains cable is damaged, the product must be disposed of. Avoid the risk of fatal injury from electric shock Check the product for damages before connecting it to the power supply. Never use the product if it is damaged in any way. Protect the mains cable from sharp edges, mechanical strain and hot surfaces. Only touch the insulated part of the mains plug when connecting or disconnecting it from the mains supply! Always unplug the mains plug from the socket before mounting, removing or cleaning it. Disconnect the product from the mains power if you are not using it for long periods (e.g. when on holiday). Never open any of the electrical equipment or insert any objects into this equipment. Such interferences pose a risk of fatal injury from electric shock. Before use, ensure that the available mains voltage matches the operating voltage required by the product (220–240 V∼, 50 Hz). Never carry the product by the mains cable. Lay the mains cable in such a way that nobody will step on or trip over it. Prevent fire and injury hazards CAUTION! RISK OF BURNS DUE TO HOT SURFACES! To prevent burns, make sure that the product has been switched off and has cooled down before touching it. Illuminants become very hot. Do not cover the product with any objects. Excessive heat can result in fire. 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 25353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 25 24.03.21 11:3024.03.21 11:3026 GB/IE Never leave the product unattended whilst in operation. Excessive heat can result in fire. The LED module is not dimmable. Do not look directly into the light source (illuminant, LED etc.). Do not look into the light source (illuminant, LED, etc.) with an optical instrument (e.g. magnifying glass).

A shattered protective covering must always be replaced. Never aim the LED light beam at reflective surfaces or at people or animals. Failure to observe this instruction can lead to eye injuries and / or loss of sight in people or animals. Even a weak LED light beam can cause eye damage. Disconnect the product from the mains supply whenever you want to set it up in a different location. The product is not suitable for use as room lighting. Before use Note: Remove all packaging materials from the product. Note: Protect delicate surfaces before setting up the product. Fully unwind the mains cable (remove the cable tie). Loosen the knurled screw

on the side of the product by turning it anticlockwise, in order to move the fold-out stand

the desired position. Then re-tighten the knurled screw

by turning it clockwise. Set up the product in the desired location. Note: The lamp head can be continuously tilted. 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 26353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 26 24.03.21 11:3024.03.21 11:3027 GB/IE Initial use Switching the product on / off Lay the mains cable in such a way that nobody will step on or trip over it. To switch the product on, plug the mains plug

into a properly installed mains socket. Note: Insert the mains plug

into an IPX4 plug socket to guarantee the protection against splashing water. To switch the product off, remove the mains plug

from the mains socket. Installing the product You can mount the product on a tripod or a wall, or hang it up using the fold-out hook

To mount the product on a tripod (not included in the scope of delivery), use the fixture for tripod installation

. Proceed as described in the instructions for your tripod. To mount the product on a wall, use the fixture for wall installation

. Information on suitable installation material can be obtained from specialist stores. Note: Pay attention to the cable length (3 m) when mounting the product on a wall. If you would like to hang up the product using the fold-out hook

from the mains socket before cleaning. DANGER OF ELECTRIC SHOCK! To ensure electrical safety, never clean the product with harsh cleaning products or immerse it in water. CAUTION! RISK OF BURNS DUE TO HOT SURFACES! Allow the product to cool down completely. Do not use solvents, petrol, etc. Doing so would damage the produc

Only clean with a dry, lint-free cloth. Use a slightly moist cloth to remove any stubborn dirt. Disposal The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1–7: plastics / 20–22: paper and fibreboard / 80–98: composite materials. The product and packaging materials are recyclable, dis- pose of it separately for better waste treatment. The Triman logo is valid in France only. Contact your local refuse disposal authority for more details of how to dispose of your worn-out product. 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 28353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 28 24.03.21 11:3024.03.21 11:3029 GB/IE To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority. Warranty and service Warranty The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below. The warranty for this product is 3 years from the date of purchase. Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you. The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your proof of purchase. This warranty becomes void if the product has been damaged, or used or maintained improperly. The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly con- sidered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts. 353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 29353561_2010_par_LED-Arbeitsstrahler_A6_content_OS.indd 29 24.03.21 11:3024.03.21 11:3030 GB/IE Service address Teknihall Elektronik GmbH Breitefeld 15 64839 Münster GERMANY 00800 333 00 888* [e-mail] [e-mail]