BDL90 - Laser level BLACK & DECKER - Free user manual and instructions

USER MANUAL BDL90 BLACK & DECKER

This Black & Decker tool has been designed to project laser lines to aid in DIY applications. This tool is intended for consumer use only.

Safety instructions

Warning! When using battery-powered tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, leaking batteries, personal injury and material damage.
Read all of this manual carefully before operating the tool.
Retain this manual for future reference.

Keep work area clean

Cluttered areas and benches can cause accidents.

Consider work area environment

Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the work area well lit. Do not use the tool where there is a risk of causing fire or explosion, e.g. in the presence of flammable liquids and gases.

Keep children away

Do not allow children, visitors or animals to come near the work area or to touch the tool.

Do not overreach

Keep proper footing and balance at all times.

Stay alert

Watch what you are doing. Use common sense. Do not operate the tool when you are tired.

Use appropriate tool

The intended use is described in this instruction manual.

Warning! The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury.

Check for damaged parts

Before use, carefully check the tool for damage. Ensure that the tool will operate properly and perform its intended function. Do not use the tool if any part is damaged or defective.

Store idle tools

When not in use, tools and batteries should be stored in a dry, locked up or high place, out of reach of children.

Repairs

This tool complies with relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user.

Additional safety instructions for non-rechargeable batteries

• Never attempt to open for any reason.
  Do not store in locations where the temperature may exceed 40^

• When disposing of batteries, follow the instructions given in the section "Protecting the environment". Do not incinerate the batteries.

• Under extreme conditions, battery leakage may occur. When you notice liquid on the batteries, proceed as follows:

• Carefully wipe the liquid off using a cloth.

Avoid skin contact.

Additional safety instructions for lasers

Read all of this manual carefully.

This product is not to be used by children under 16.

Warning! Laser radiation.

Do not look into the laser beam.

Do not view the laser beam directly with optical instruments.

Refer to the laser product characteristics.

This laser complies with class 2 according to IEC 60825-1+A1+A2:2001. Do not replace a laser diode with a different type. If damaged, have the laser repaired by an authorised repair agent.
Do not use the laser for any purpose other than projecting laser lines.
An exposure of the eye to the beam of a class 2 laser is considered safe for a maximum of 0.25 seconds. Eyelid reflexes will normally provide adequate protection. At distances over 1m the laser complies with class 1 and thus is considered completely safe.
- Never look into the laser beam directly and intentionally.
Do not use optical tools to view the laser beam.
- Do not set up the tool at a position where the laser beam can cross any person at head height.
Do not let children come near the laser.

Features

1. On/off switch
2. Laser apertures
3. Mounting bracket
4. Vials
5. Scale

Assembly

Warning! Make sure that the tool is switched off.

Fitting the batteries (fig. A)

• Remove the battery cover (6) from the tool.
• Insert the batteries into the tool in the orientation as shown.
• Refit the cover and let it click into place.

Installing the tool (fig. B)

The tool can be installed on a horizontal surface such as a floor or a table. To optimise the length of the laser line, the tool must be installed onto its bracket. Alternatively, the tool can be mounted to a wall.

Fitting the tool to the mounting bracket

Install the unit by clinging the bottom to the magnet (7). To remove the unit from the bracket, pull the unit off.

Wall mounting (fig. B & C)

The round plate in the bottom of the wall mount rotates to three positions in order to facilitate wall mounting using a screw (I), a small nail (II), or an adhesive strip (III).

Keyhole wall mount

The keyhole wall mount (8) is used for mounting to most wall constructions.

Drive a screw or nail into the wall.
- Rotate the plate (9) into position (I).
Hang the bracket onto the fastener by the keyhole (8).
Fit the tool to the bracket.

Wall pin

If the unit is mounted to drywall or other soft materials, a wall pin must be used:

• Rotate the plate (9) into position (II).
• Hold the bracket against the wall.
  Drive a small nail through the hole into the wall.
  Fit the tool to the bracket.

Adhesive strip

If the unit is mounted to surfaces where screws or nails cannot be used, a removable adhesive adhesive strip must be used. Adhesive strips can be obtained from your local retailer. Warning! Test the strip on an inconspicuous area to make sure it does not damage the surface material.

• Rotate the plate (9) into position (III).
• Peel the protective foil from one side of the strip.
• Stick the strip to the bracket.
• Peel the protective foil from the other side of the strip.
• Press the bracket with the strip to the wall.
• Fit the tool to the bracket.

To remove the strip, proceed as follows:

Remove the tool from the bracket. Hold the bracket with one hand and grasp the end of the adhesive strip with the other hand.
- Slowly stretch the strip parallel to the wall and away from the bracket, until the entire strip has released.
Dispose of the strip.

Use

Install the tool as required.
Switch the tool on.
- Adjust the position of the tool as necessary to position the laser lines. Be aware that extreme temperature changes may affect the adjustment of the unit.
After finishing work, always switch off the tool.

Switching on and off

To switch on, slide the switch (1) into position I.
To switch off, slide the switch (1) into position 0.

Levelling the laser lines (fig. D & E)

When projecting laser lines in horizontal applications, adjust the unit as necessary until the vials (4) are level.
- When projecting laser lines in vertical applications, adjust the unit as necessary until one of the vials (4) is level.

Using the scale

The scale (5) can be used to transfer a square angle.

Position the unit with the laser lines at the starting point.
Align the 0^ position on the scale with one of the laser beams.
Holding the bracket (3) with one hand, position the tool with the other hand as necessary.

Cleaning and maintenance

Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

To clean the tool, use only mild soap and a damp cloth. Never let any liquid get inside the tool and never immerse any part of the tool into liquid.

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste.

Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

ENGLISH

Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.

Batteries

At the end of their useful life, discard batteries with due care for our environment.

Remove the batteries as described above.
Place the batteries in a suitable packaging to ensure that the terminals cannot be short-circuited.
Take the batteries to a local recycling station.

Technical data
BDL90

	BDL90
Voltage V 3
Battery size 2 x LR03 (AAA)
Wave length nm 630-690
Laser class 2
Laser power mW < 4
Laser length cm 600
Accuracy (at 1 m) mm +/- 1
Operating temperature °C 0 - 40
Weight kg 0.2

EC declaration of conformity

BDL90

Black & Decker declares that these products conform to:

IEC 60825-1, EN 61000

Kevin Hewitt

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Guarantee

Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless:

The product has been used for trade, professional or hire purposes:
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign objects, substances or accidents:
Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at:

www.2helpU.com.

Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk.

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

DEUTSCH

Garantie

Spennymoor, County Durham DL16 6JG

Royaume-Uni

01-04-2006

Garantie

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Garanzia

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Garantie

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Garantía

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Garantia

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Reservdar / reparationer

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

Reservedele / reparationer

Varoitus! Lasersately.

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

01-04-2006

PpoeiOnoInon! BeaawOeTe 0T to epyaeeio evau anevpyoOnuEvO.

TOnoTeRtnon mparapiwv (Eik.A)

ApaipoeToKaUmuMaatapiaC(6) ano to epyaIio.
Toonotne Tc natape c eo o eyaio kata tov unodekvuouevo npoavatoiao.
EnavatooEto KaLmuKa apote To va aopalio stn owot tou eon.

Eykaotraon tou epyaleou (ek.B)

Ynapexi duvatomta eykataotaonc tou epyaieou enavw oe opizovia enipaveia, onwc danedo n tranepi. Tia va beAIOTE to kpos mc ypaunc lezep, to epyaio npenvi va Eykataostei oTov ouykarntn Tou. Aiaopetika, to epyaio mnpei va tonoetnei naW OE Toixo.

TOnoTeTnTo epyaleoiOTo ouyKpattnEykataaans

EyataoTnOte T m ova kOaWvTaC To KATw epoc stov maaynt (7).
Ia va anoakpuveTn movada ano to ouykpattn, TpaBnE TnV.