Bravia KD65XG8599 - Television SONY - Free user manual and instructions

Product type	LED 4K TV
Brand	Sony
Model	Bravia KD65XG8599
Screen size	65 inches (164 cm)
Resolution	3840 x 2160 pixels (4K Ultra HD)
Display technology	LED LCD with Direct LED backlight
Dimensions (without stand)	Approximately 1450 x 836 x 70 mm (W x H x D)
Weight (without stand)	Approximately 20 kg
Power supply	220-240 V AC, 50 Hz
Power consumption	Approximately 150 W (typical)
Smart TV	Yes, Android TV system
HDR	HDR10, HLG
Connectivity	4x HDMI, 3x USB, Ethernet, Wi-Fi, Bluetooth
Compatible wall mount	Sony SU-WL450 (included in the box)
Wall mounting standard	VESA 400 x 300 mm (standard), 400 x 300 mm (slim)
Maintenance and cleaning	Dust with a soft, dry cloth. Do not use abrasive products.
Safety	Wall installation by a certified professional. Do not hang or lean on the TV.
Included parts	base plates, pulleys, spacers, screws, base adapters, safety strap
Repairability	Repairability index not provided. Sony recommends contacting an approved service.

Frequently Asked Questions - Bravia KD65XG8599 SONY

How to install the TV on the wall with the SU-WL450 mount?

Installation must be carried out by a certified installer. Use at least four 8 mm diameter screws suitable for the wall. Attach the base to the wall, then hang the TV by sliding the pulleys into the base. Tighten the safety strap at the bottom. Refer to the user manual for precise dimensions.

What is the maximum weight supported by the wall mount?

The wall must support at least four times the weight of the TV. The weight of the KD65XG8599 TV is approximately 20 kg without stand. Use wall plugs and screws suitable for the wall type.

Can I install the TV with a slim mount (close to the wall)?

Yes, the SU-WL450 mount allows standard or slim mounting. In slim mounting, access to rear terminals is limited. Make sure to connect all cables before hanging the TV.

What to do if the TV moves after installation?

Check that the safety strap is properly tightened and fixed to the wall with a 5 mm screw. If the looseness persists, the installation is not correct; have it checked by a professional.

How to clean the TV screen?

Use a soft, dry cloth (microfiber). Do not use chemical products, alcohol, or solvents. For stubborn stains, lightly dampen the cloth with distilled water.

What cables are needed for a wall installation?

Connect all cables (HDMI, USB, antenna, power) before attaching the TV to the wall. If you run the cables through the wall, do so before installation and plan a hole outside the mounting area.

Is the wall mount included with the TV?

Yes, the Sony SU-WL450 wall mounting bracket is included in the package. Check that all parts are present: base plate, pulleys, spacers, screws, base adapters and strap.

What are the VESA mounting dimensions?

The TV is compatible with VESA 400x300 mm in standard and slim mounting. Use the provided spacers to adjust the thickness.

Can I tilt the TV after wall installation?

No, the SU-WL450 mount does not allow tilting. The TV is fixed. For tilting, use a suitable articulated mount (not included).

What to do if I lose the provided screws?

Contact an authorized Sony dealer to obtain replacement parts. Do not use unsuitable screws, as this could compromise safety. Standard 8 mm and 5 mm diameter screws are commercially available.

USER MANUAL Bravia KD65XG8599 SONY

• In the actual model names, the "□□" indicates numbers and/or characters specific to each model.

To Customers: For product protection and safety reasons, Sony strongly recommends that installation of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

To Sony Dealers and Contractors: Provide full attention to safety during the installation, periodic maintenance, and examination of this product.

Sufficient expertise is required for installing this product, especially to determine the strength of the wall for withstanding the TV's weight. Be sure to entrust the attachment of this product to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation.

For safety and proper installation, follow the Wall-mount Bracket Operation Instructions, TV Setup Guide, and the directions in this manual.

On Safety

Thank you for purchasing this product.

To Customers

Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable for any damages or injury caused by mishandling or improper installation, or installing any other than the specified product. Your Statutory Rights (if any) are not affected.

To Sony dealers

Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or improper installation. Please give this manual to the customer after installation.

This instruction manual shows the correct handling of the product and important precautions necessary to prevent accidents. Be sure to read this manual thoroughly and use the product correctly. Keep this manual available for future reference.

Products by Sony are designed with safety in mind. If the products are used incorrectly, however, it may result in a serious injury through fire, electric shock, the product toppling over, or the product dropping. Be sure to observe the precautions for safety to prevent such accidents.

CAUTION

Specified products

This Wall-Mount Bracket is designed for use with the products specified TVs. For TVs, refer to their Reference Guide to verify that the Wall-Mount Bracket can be used.

To Customers

WARNING

If the following precautions are not observed, serious injury or death through fire, electric shock, or the product dropping can result.

Be sure to subcontract the installation to licensed contractors and keep small children away during the installation.

If the Wall-Mount Bracket or the TV is not installed correctly, the following accidents may occur. Be sure licensed contractors carry out installation.

The TV may fall and cause a serious injury such as a bruise or a fracture. - If the wall on which the Wall-Mount Bracket is installed is unstable, uneven, or not perpendicular to the floor, the unit may fall and cause injury or property damage. The wall should be capable of supporting a weight of at least four times the TV weight. (Refer to your TV's Reference Guide for its weight.) - If the installation of the Wall-Mount Bracket on the wall is not sufficiently sturdy, the unit may fall and cause injury or property damage.

Be sure to subcontract moving or dismounting of the TV to licensed contractors.

If persons other than licensed contractors transport or dismount the TV, it may fall and cause injury or property damage. Be sure that two or more persons (three or more persons for 75 inches and above TV set) carry or dismount the TV.

Do not remove screws, etc., after mounting the TV.

If you do so, the TV may fall and cause injury or property damage.

Do not make alterations to the parts of the Wall-Mount Bracket.

If you do so, the Wall-Mount Bracket may fall and cause injury or property damage.

Do not mount any equipment other than the specified product.

This Wall-Mount Bracket is designed for use with the specified product only. If you mount equipment other than specified, it may fall or break, and cause injury or property damage.

Do not apply any load other than the TV on the Wall-Mount Bracket. Do not shake the TV left/right, up/down.

If you do so, the TV may fall and cause injury or property damage.

Do not lean on or hang from the TV.

Do not lean on or hang from the TV as it may fall on you and cause serious injury.

CAUTION

If the following precautions are not observed, injury or property damage may occur.

Do not handle the product with excessive force during cleaning or maintenance.

Do not apply excessive force on the topside of the TV. If you do so, the TV may fall and cause injury or property damage.

Precautions

• If you use the TV installed on the Wall-Mount Bracket for a long time, the wall behind or above the TV may become discolored or the wallpaper may come unstuck, depending on the material of the wall.
• If the Wall-Mount Bracket is removed after installing it on the wall, the screw holes are left.
• Do not use the Wall-Mount Bracket in a place where it is subjected to mechanical vibrations.

Installing the Wall-Mount Bracket

To Sony Dealers

WARNING

The following instructions are for Sony dealers only. Be sure to read the safety precautions described above and pay special attention to safety during the installation, maintenance, and checking of this product.

Do not install the Wall-Mount Bracket on wall surfaces where the corners or the sides of the TV protrude away from the wall surface.

Do not install the Wall-Mount Bracket on wall surfaces such as a pillar, where the corners or the sides of the TV protrude away from the wall surface. If a person or object happens to hit the protruded corner or side of the TV, it may cause injury or property damage.

Do not install the TV over or under an air conditioner.

If the TV is exposed to water leaks or air current from an air conditioner for a long time, it may cause a fire, an electric shock, or a malfunction of the TV.

Be sure to install the Wall-Mount Bracket securely to the wall following the instructions in this instruction manual.

If any of the screws are loose or fall out, the Wall-Mount Bracket may fall and cause injury or property damage. Be sure to use the appropriate screws for the material of the wall and install the unit securely using four or more screws of 8 mm diameter (or equivalent).

Be sure to use the supplied screws and attachment parts properly following the instructions given in this instruction manual. If you use substitute items, the TV may fall and cause bodily injury to someone or damage to the TV.

Be sure to assemble the bracket properly following the instructed procedure explained in this instruction manual.

If any of the screws are loose or fall out, the TV may fall and cause bodily injury to someone or damage to the TV.

Be sure to tighten the screws securely in the designated position.

If you fail to do so, the TV may fall and cause bodily injury to someone or damage to the TV.

Be careful not to subject the TV to shock during installation.

If the TV is exposed to shock, it may fall or break apart. This may cause injury.

Be sure to install the TV on a wall that is both perpendicular and flat.

If you fail to do so, the TV may fall and cause injury.

After proper installation of the TV, secure the cables properly.

If people or objects get tangled with cables, this may result in injury or damage to the TV.

Do not allow the mains lead or the connecting cable to be pinched.

If the mains lead or the connecting cable is pinched between the unit and the wall or is bent or twisted by force, the internal conductors may become exposed and cause a short circuit or an electrical break. This may cause a fire or an electric shock.

The screws needed to secure the Wall-Mount Bracket to the wall are not supplied.

Use the appropriate screws for the wall material and structure when mounting the Wall-Mount Bracket.

Table of Contents

Preparing for installation. 5

Checking the parts. 5

Deciding on the installation location 6

Installing the Base on the wall 8

Preparing for the installation of the TV. 9

KD-85/75XG85□□, KD-75XG87□□

KD-65/55XG87□□, KD-65/55XG85□□.11

Installing the TV on the wall 13

KD-85/75XG85□□, KD-75XG87□□.13

KD-65/55XG87□□, KD-65/55XG85□□.15

Confirming the completion of the

installation 18

Other information. 18

Specifications 18

Installing the TV onto the wall

Installation procedure differs, depending on your TV.

Use the Wall-Mount Bracket SU-WL450 to install the TV to the wall.

Note

• Be sure to store the removed screws in a safe place, keeping them away from children.

Preparing for installation

• Have the TV's Reference Guide and Setup Guide at hand before installation.
• Be sure to have a Phillips screwdriver that fits the screws prior to the assembly.
• Confirm the installing position of your TV.
• Prepare four or more screws of 8 mm diameter and one screw of 5 mm or equivalent (not supplied). Select screws suitable for the material of the wall.

Checking the parts

Supplied with SU-WL450

• Verify that all the parts are included.

A Base (20) (1) B Pulley (2)
◎ PSW 6x20 (4)◎ PSW 4x20 with Bush (2)
◎ Spacer (20) (2)◎ Belt (1)
◎ Bush (20) (M4) (2)◎ PSW 4x20 (2)
① Base Adaptor (2)①	PSW 4x10 (8)
◎ Spacer (60) (2)◎ PSW 6x50 (2)
◎ Bush (M4) (2)◎ PSW 4x50 (2)

Deciding on the installation location

1 Decide on the installation location.

Make sure that the wall has enough space for the TV and is capable of supporting a weight of at least four times that of the TV.

Refer to the following table on installing the TV to the wall. Refer to your TV's Reference Guide for the TV's weight.

Standard mounting Slim mounting Screen centre point

Unit: mm

Model Name	Display dimensions		Screen centre dimension		Length for mounting
	a	b	c	d	e
					Standard mounting	Slim mounting
KD-85XG85□□	1,909	1,097	251	803	142	100
KD-75XG87□□ KD-75XG85□□	1,673	963	107	595	116	75
KD-65XG87□□ KD-65XG85□□	1,450	836	99	523	115	73
KD-55XG87□□ KD-55XG85□□	1,231	713	106	468	115	73

Note

• Figures in the table may differ slightly depending on the installation.
• When your TV is installed on the wall, the upper side of the TV slightly leans forward.

Allow for suitable clearance between the TV and the ceiling and protruding parts of the wall as shown below.

Unit: mm

To ensure proper ventilation and prevent the collection of dirt or dust:

Do not lay the TV set flat, install upside down, backwards, or sideways. - Do not place the TV set on a shelf, rug, bed or in a closet. - Do not cover the TV set with a cloth, such as curtains, or items such as newspapers, etc. - Do not install the TV set as shown below.

Air circulation is blocked.

Note

• If you intend to route the cables in the wall, make a hole in the wall to insert the cables before beginning the installation.

To prevent pinching the cables, prepare a hole in the wall somewhere outside the perimeter of the Base (20) A, Base Adaptor 1 and Spacer (20) E, Spacer (60) K.

2 Select Wall mounting style. It is selectable as shown below.

2-a Standard mount

2-b Slim mount

Refer to the table of step 1.

WARNING

• When 2-b is selected, rear terminal access is limited.

2-a 2-b

3 Refer to the below table about the Base Adaptor fitting location. In case of selecting 2-b, then skip this step.

Model Name Hook location
KD-85XG85□□
KD-75XG87□□	a
KD-75XG85□□
KD-65XG87□□
KD-65XG85□□	b
KD-55XG87□□
KD-55XG85□□

Fit Base Adaptor ① by using Screw (PSW 4x10) ⑧ to Base (20) ④ when selecting 2-a.

4 Decide the positions of the screws for installing the Base (20) A.

Refer to the specifications on page 18. When selecting 2-a, please use the hole positions of Base Adaptor ①.

WARNING

The wall that the TV will be mounted on should be able to support a weight of at least four times that of the TV (Refer to your TV's Reference Guide for its weight.). - Determine the strength of the wall the TV will be mounted on. Reinforce the wall sufficiently, if necessary.

Installing the Base on the wall

• Use four or more screws of 8mm diameter or equivalent (not supplied).
• Fit four screws to the holes of Base Adaptor ① with Base (20) A (2-a only). Install the Base (20) A on the wall horizontally.

Preparing for the installation of the TV

Refer to the Setup Guide for stand installation.

KD-85/75XG85□□, KD-75XG87□□

1 Mark the installation location on the wall.

• Use masking tape, etc. (not supplied) to mark the location of the TV near the Base or Base Adaptor. Refer to the following table.

Model Name	Length for marking			Screen centre dimension
	a	b	c	d
KD-85XG85□□	1,909	683	200	251
KD-75XG87□□ KD-75XG85□□	1,673	468	200	107

2 Remove the screws from the rear of the TV.

3 Attach the Attachment parts for Wall-Mount Bracket. Check the Attachment parts by referring to "Supplied with SU-WL450" in "Checking the parts" on page 5.

Note

• Firmly secure the attachment parts using screws.
• When using an electric screwdriver, set the torque setting to approximately 1.5 N·m {15 kgf·cm}.
• Be sure to store the used or unused parts in a safe place for future use. Retain this manual for future reference.

Standard mounting (2-a) Slim mounting (2-b)

Note

• You cannot use some of the terminals on the rear of the TV when using this mounting style.

4 Connect the necessary cable(s) to the TV.

Make sure to connect the cables before installing the TV on the wall. You will be unable to connect the cables when the TV is installed. Refer to the Reference Guide supplied with your TV.

Note

• Subcontract the cable routing in the wall to a licensed contractor.
• Bundle the connecting cables to prevent stepping on them before wall mounting.

5 Detach the Table-Top Stand from the TV.

• Remove one side of the Table-Top Stand at a time. Firmly hold the Table-Top Stand securely with both hands while the other people lift up the TV.

KD-85XG85□□

KD-75XG87□□, KD-75XG85□□

• Repeat the previous step and remove the other side of the Table-Top Stand.

Note

• Three or more people are required to detach the Table-Top Stand.
• Be careful not to use excessive force while detaching the Table-Top Stand from the TV as it may cause the TV set to fall resulting in personal injury or physical damage to the TV. Take care when handling the Table-Top Stand to prevent damage to the TV.
• Be careful when lifting the TV as the Table-Top Stand is detached, the Table-Top Stand may topple over and cause personal injury. Take care when removing the Table-Top Stand from the TV to prevent it from falling over and damaging the surface that the TV is sitting on.

1 Remove the screws from the rear of the TV.

2 Attach the Attachment parts for Wall-Mount Bracket. Check the Attachment parts by referring to "Supplied with SU-WL450" in "Checking the parts" on page 5.

Note

• Firmly secure the Attachment parts using screws.
• When using an electric screwdriver, set the torque setting to approximately 1.5 N·m {15 kgf·cm}.
• Be sure to store the used or unused parts in a safe place for future use. Retain this manual for future reference.

Standard mounting (2-a)

Slim mounting (2-b)

Note

• You cannot use some of the terminals on the rear of the TV when using this mounting style.

3 Connect the necessary cable(s) to the TV.

Make sure to connect the cables before installing the TV on the wall. You will be unable to connect the cables when the TV is installed.

Refer to the Reference Guide supplied with your TV.

Note

• Subcontract the cable routing in the wall to a licensed contractor.
• Bundle the connecting cables to prevent stepping on them before wall mounting.

4 Detach the Table-Top Stand from the TV.

• Remove one side of the Table-Top Stand at a time. Firmly hold the Table-Top Stand securely with both hands while the other people lift up the TV.

• Repeat the previous step and remove the other side of the Table-Top Stand.

Note

• Three or more people are required to detach the Table-Top Stand.
• Be careful not to use excessive force while detaching the Table-Top Stand from the TV as it may cause the TV set to fall resulting in personal injury or physical damage to the TV. Take care when handling the Table-Top Stand to prevent damage to the TV.
• Be careful when lifting the TV as the Table-Top Stand is detached, the Table-Top Stand may topple over and cause personal injury. Take care when removing the Table-Top Stand from the TV to prevent it from falling over and damaging the surface that the TV is sitting on.

Installing the TV on the wall

KD-85/75XG85□□, KD-75XG87□□

1 Lift the TV.

• For the location of the Pulleys (B) to hang on the Base or Base Adaptor, refer to the table of step 3 in "Deciding on the installation location" on page 7.
• Make sure that the rear of the TV touches the Base or Base Adaptor when holding the TV.

Note

• Hold the TV securely with both hands and make sure the Belt (F) and the bottom of the TV align with the masking tape.
• Carry the TV with three people and the person who is in front of the TV leads the others to adjust the position.

Take great care when installing the TV to the wall, especially for the person who is supporting the TV from below. The television set may fall, causing serious bodily injury or even death.

2 Install the TV onto the Base or Base Adaptor.

• Gently slide down the TV and hang the Pulleys (B) attached to the rear of the TV to the Base or Base Adaptor, making sure to confirm the shape of the holes. After installing the TV on the wall, confirm the Pulleys (B) are firmly latched into the Base or Base Adaptor.
• Release both hands slowly to ensure that the TV does not fall.

• After installing the TV on the wall, remove the masking tape, etc. from the wall.

2-a

2-b

WARNING

• Be sure that two or more persons (three or more persons for 75 inches and above TV set) hold the TV when carrying it.

3 Preventing the bottom of the TV from shifting.

Take up the slack of Belt F and attach it to the wall tightly.

• Use a 5 mm diameter screw or equivalent (not supplied).

Note

Try to pull the bottom of the TV towards yourself slightly, to make sure that it does not move forward. If there is any movement, it is not fixed correctly, and the Belt should be secured firmly again.

KD-65/55XG87□□

KD-65/55XG85□

1 Lift the TV.

• For the location of the Pulleys to the hang on the Base or Base Adaptor, refer to the table of step 3 in "Deciding on the installation location" on page 7.
• Make sure that the rear of the TV touches the Base or Base Adaptor when holding the TV.

Note

• Hold the TV securely with both hands.

2 Install the TV onto the Base or Base Adaptor.

Gently slide down the TV and hang the Pulleys ⑧ attached to the rear of the TV to the Base or Base Adaptor, making sure to confirm the shape of the holes. After installing the TV on the wall, confirm the Pulleys ⑧ are firmly latched into the Base or Base Adaptor. - Release both hands slowly to ensure that the TV does not fall.

2-a

2-b

↓

↓

WARNING

• Be sure that two or more persons (three or more persons for 75 inches and above TV set) hold the TV when carrying it.

3 Preventing the bottom of the TV from shifting.

Take up the slack of Belt F and attach it to the wall tightly.

• Use a 5 mm diameter screw or equivalent (not supplied).

Note

Try to pull the bottom of the TV towards yourself slightly, to make sure that it does not move forward. If there is any movement, it is not fixed correctly, and the Belt should be secured firmly again.

Confirming the completion of the installation

Check the following points.

• The Pulleys (B) are firmly hung onto the Base or Base Adaptor.
• The cord and the cable are not twisted or pinched.
• The Belt (F) is tight with no slack.

WARNING

• Improper placement of the mains lead, etc. may cause fire or electric shock through a short circuit. Be sure to confirm the completion of the installation for safety.

Other information

When removing the TV, reverse the previous installation procedure.

WARNING

• Be sure that two or more persons (three or more persons for 75 inches and above TV set) hold the TV when removing it.

Specifications

Dimensions: (Approx.) [mm]

a : 400

b : 300

c:200

d : 100

e:80

f:480

g: 100

h1: 20 (case 2-b)

h2: 60 (case 2-a)

Weight (base only): (Approx.) [kg]

0.8

Design and specifications are subject to change without notice.

Dimensions: (Approx.) [mm]

a: 400

b: 300

c: 200

d: 100

e: 80

f: 480

g: 100

h1: 20 (case 2-b)

h2: 60 (case 2-a)

Dimensions: (Approx.) [mm]

a: 400

b: 300

c: 200

d: 100

e: 80

f: 480

g: 100

h1: 20 (case 2-b)

h2: 60 (case 2-a)

Weight (base only): (Approx.) [kg]

0.8

Clearance hole for installation. 5

Check of parts 5

Find a location 6

Preparing for installation

1 Find the TV's location.

Have the wall bracket and the installation bracket nearby before installation. - Before mounting, make sure you have a Phillips screwdriver that fits the screws. - Verify the position of the TV bracket. Prepare three or more 5mm screws (if not provided). Use screws that are suitable for the wall material.

Check the accessories

Position indicator (2-b)

Note

Position indicator (2-b)

Note

Dimensions: (approx.) [mm]

a:400

b:300

c:200

d:100

e:80

f:480

q:100

h1:20 (case 2-b)

h2:60 (case 2-a)

Insert the screws into the other holes after mounting the TV.

If you do not, the TV may fall and cause injury or damage to property.

Do not skip the wall-mount bracket installation steps.

If you do not, the wall-mount bracket may fall and cause injury or damage to property.

Do not mount other equipment other than the specified product.

This wall-mount bracket is designed for use only with the specified product. If you mount equipment different from the specified one, it may fall and cause injury or damage to property.

Do not place the wall-mount bracket on any other item than the TV. Do not place the TV on a slanted or uneven surface.

If you do, the TV may fall and cause injury or damage to property.

Do not lean on or sit on the TV.

Do not lean on or sit on the TV, as it may fall and cause serious injury.

If the safety measures are not followed, there is a risk of injury or damage to property.

Do not use the product with excessive force during installation or adjustment.

Do not apply excessive force to the top part of the TV. If you do, the TV may fall and cause injury or damage to property.

Safety measures

• If you use the TV for a long time, mounted on a wall mount, the wall behind it may become discolored or the wallpaper may peel, depending on the wall material. If the wall mount is installed on the wall, the screws may remain visible. Do not use the wall mount in places where it may be subjected to mechanical vibrations.

Wall mount installation

For Sony dealers

WARNING

These instructions are for Sony dealers only. Read the safety measures described above and pay special attention to safety during installation, maintenance, and operation of the product.

Do not install the wall mount on wall surfaces where the TV's sides or edges protrude from the wall surface.

Do not install the wall mount on wall surfaces, such as columns, where the TV's sides or edges protrude from the wall surface. If the TV is subjected to impact or falls, it may cause injury or damage to property.

Do not install the TV above or below air conditioners.

If the TV is exposed to prolonged airflow from an air conditioner, it may cause fire, electric shock, or malfunction of the TV.

Install the wall mount securely to the wall by following the instructions in this manual.

If the wall is not strong enough, the wall mounting bracket may fall and cause property damage. Use appropriate wall material anchors and mounting screws, and securely tighten them using four or more screws with a diameter of 8 mm (or equivalent).

Mounting the TV on the wall

Preparing for TV installation...9

KD-85/75XG85□□, KD-75XG87□□

KD-65/55XG87□□, KD-65/55XG85□□.11

Mounting the TV on the wall.13

KD-85/75XG85□□, KD-75XG87□□.13

KD-65/55XG87□□, KD-65/55XG85□□.15

Checking the connections

Mounting 18

Other information 18

Specifications.. 18

Mounting the TV on the wall

The mounting procedure differs depending on the TV.

Use the wall mounting bracket SU-WL450 to mount the TV on the wall.

Do not allow the fallen screws to be placed in a safe place, as they may be lost.

Mounting instructions

The installation instructions for the TV must be followed before mounting. - Use a Phillips screwdriver that matches the screws. - Choose the mounting position for the TV. - Tighten the four 8 mm diameter screws and one 5 mm diameter screw or equivalent (not included). Select screws suitable for the material of the wall.

Selecting the frequency

Supplied with SU-WL450

• Select all available channels.

A Oснова (20) (1) B Мakара (2)
◎ PSW 6x20 (4)◎ PSW 4x20 c Втулka (2)
E Дистанционна Втулka (20) (2)	F Колан (1)
◎Втулka (20) (M4) (2)	H PSW 4x20 (2)
◎Aдантетер на Основатa (2)	◎J PSW 4x10 (8)
◎Дистанционна Втулka (60) (2)	◎L PSW 6x50 (2)
◎Втулka (M4) (2)◎PSW 4x50 (2)

Determining the mounting location

1 Select the mounting location.

Make sure the wall has enough space for the TV and is strong enough to support its weight, including the TV's weight. See the wall mounting table for the TV. See the TV's instruction manual for its weight.

Standard mounting Slim mounting Center mounting

Unit: mm

Иme на морел	Размери на ekранa		Размер на цentьра на ekранa		Дылжина на моHTах
	a	b	c	d	e
					Стоцартын MOHTах	Teсен MOHTах
KD-85XG85□□	1909	1 097	251	803	142	100
KD-75XG87□□ KD-75XG85□□	1673	963		107	595	116
KD-65XG87□ KD-65XG85□□	1450	836	99	523	115	73
KD-55XG87□ KD-55XG85□□	1231	713	106	468	115	73

Note

• The values in the table may differ slightly depending on the mounting method. When your TV is mounted on the wall, its top may tilt slightly forward.

Leave a suitable distance between the TV, the wall, and the protruding parts of the wall, as shown below.

Read the ventilation rules to prevent dust accumulation:

Do not place the TV on a flat surface with the screen side down, do not mount it upside down with the top edge facing down, or on an unstable surface. Do not place the TV on top of radiators, heaters, stoves, or other heat sources. Do not cover the TV with cloth, such as curtains, or objects like vases or plants. Do not mount the TV as shown below.

Air ventilation is blocked.

Caution

If you intend to route cables through the wall, make an opening in the wall to pass the cables before installation. To prevent cable damage, make the wall opening outside the perimeter of the base (20) A, behind the base 1, and the grommet (20) E, and the grommet (60) K.

2 Select the mounting wall. The distance from the rear part of the TV to the wall can be selected as shown below.

2-a Standard mounting

2-b Tight mounting

See the table from reference 1.

WARNING

When 2-b is selected, the rear terminals are limited.

2-a 2-b

3 See the table below for the position of the alternative hinge for the base. If you have selected 2-b, skip this reference.

Име на мodyел Мecтоноожени На Кукatinga
KD-85XG85□□
KD-75XG87□□	a
KD-75XG85□□
KD-65XG87□□
KD-65XG85□□	b
KD-55XG87□□
KD-55XG85□□

Mount the base hinge ① using screw (PSW 4x10) J to the base (20) A, if you have selected 2-a.

Determine the positions for mounting the screws on the base (20) A.

See the specifications on page 18.

When you select 2-a, use the special holes for the base adapter on the base ①

WARNING

The wall on which you mount the TV must be able to support at least four times the TV's weight (see the TV's reference guide regarding its weight).

• Determine the wall's suitability for mounting the TV. If necessary, reinforce the wall sufficiently.

Mounting the base on the wall

• Use four or more screws with a diameter of 8 mm or equivalent (not supplied). Secure the four screws in the holes of the base adapter ① with the base (20) A (only 2-a).
• Mount the base (20) A horizontally on the wall.

Preparation for mounting the TV

When mounting, follow the setup guide.

KD-85/75XG85□□，KD-75XG87□□

1 Mark the location for mounting on the wall.

• Use only self-tapping screws or similar (not supplied) to mark the TV's location, near the base or base adapter. See the following table.

Мернейнци: mm
Име на м odeл	Дыжина 3a otбелязвае	Размер на центьра на ekранa
	a b c d
KD-85XG85□□	1909 683 200 251
KD-75XG87□□	1673 468 200 107
KD-75XG85□□

2 Remove the screws from the back of the TV.

Attach the wall mount bracket to the wall using the screws. Check the bracket by comparing it with the "Supplied with SU-WL450" in "Checking the parts" on page 5.

Note

Attach the wall mount bracket with the screws. When using an electric screwdriver, set the torque to approximately 1.5 N·m {15 kgf·cm}. Store the used and unused parts safely for future use. Store the instruction manual for future reference.

Standard mounting (2-a)

Tight mounting (2-b)

Note

When using this mounting style, you can use the terminals on the back of the TV.

4 Connect the necessary cables to the TV.

Make sure you have connected the cables before mounting the TV on the wall. You can connect them after the TV is mounted. Refer to the instruction manual supplied with your TV.

Note

Remove the cable covers from the wall or the cable guides. - Make sure to connect the cables before mounting to the wall, so you don't have to reach behind it.

5 Attach the TV stand.

• Remove one side of the stand. Insert the stand securely into the two holes until they click into place on the TV.

KD-85XG85□□

KD-75XG87□□, KD-75XG85□□

• Remove the wall mount and detach the other side of the stand for the TV.

Note

Before installing the TV stand, the screws and other parts must be removed. Be careful not to apply excessive force when removing the TV stand from the TV, as the TV may fall and be damaged, or the TV itself may be damaged. Be careful when working with the TV stand to avoid damage to the TV. Be careful when lifting the TV, as the stand is not secured and the stand may come off and cause injury. Be careful when moving the TV stand away from the TV to prevent falling and damage to the surface on which the TV stands.

KD-65/55XG87□□,

KD-65/55XG85□

1 Remove the screws from the rear side of the TV.

2 Attach the wall mount brackets to the wall. Check the brackets by comparing with "Supplied with SU-WL450" in "Checking the parts" on page 5.

Note

Secure the wall mount brackets with the screws. When using an electric screwdriver, set the torque to approximately 1.5 N·m {15 kgf·cm}. - Store the screws and parts in a safe place for future use. Keep the instruction manual for future reference.

Standard mounting (2-a)

Tight mounting (2-b)

Note

When using the mounting screws, be sure to use the ones from the terminals of the TV.

3 Connect the necessary cables to the TV.

Make sure the cables are connected before mounting the TV on the wall. You may not be able to connect them after the TV is mounted. Refer to the instruction manual supplied with your TV.

Make sure to route the cable along the wall or floor. - Secure the cable to the wall to prevent it from being stepped on.

4 Remove the TV stand.

• Remove the side of the stand. Insert the stand securely with the two screws, then attach the TV.

Repeat the procedure for the other side of the stand.

The installation of the stand must be carried out by two people. Be careful not to apply excessive force when removing the stand from the TV, as the TV may fall and cause injury or damage to the TV. - Be careful when working with the stand to avoid damage to the TV. Be careful when lifting the TV, as the stand is not secured and may slide off. Be careful when moving the stand away from the TV to prevent damage to the surface on which the TV stands.

Mounting the TV on the wall

KD-85/75XG85□□，KD-75XG87□□

1 Lift the TV.

For the position of the marks ⑧ for drilling on the base plate, refer to the table in "Determining the mounting position" on page 7. - Make sure the side of the TV is aligned with the base plate when holding the TV.

Hold the TV with both hands. Make sure the hooks on the bottom side of the TV are parallel with the self-tapping screws. Adjust the TV position so that the screws can be inserted.

Be careful when mounting the TV to the wall, especially for the person holding it from below, as the TV may fall and cause injury or damage.

2 Mount the TV onto the base plate.

Carefully lift the TV and attach brackets B to the occupied side of the TV, to the base of the adapter for the base, checking the format of the opening. After mounting the TV, check that brackets B are securely attached to the base or the base adapter. Also pull both cords to make sure the TV does not fall.

After mounting the TV to the wall, remove the self-tapping screws from the wall.

2-a

2-b

CAUTION

• Make sure that two or more people (two or more people for a complete TV with a size of 75 inches) hold the TV when carrying it.

2 Mount the TV onto the base or the base adapter.

Carefully lift the TV and attach brackets B, secured to the occupied side of the TV, to the base or the base adapter, checking the format of the opening. After mounting the TV, check that brackets B are securely attached to the base or the base adapter. - Also pull both cords to make sure the TV does not fall.

2-a

2-b

↓

↓

CAUTION

• Make sure that two or more people (two or more people for a complete TV with a size of 75 inches) hold the TV when carrying it.

3 Adjustment

Placement of the wall-mounted part of the TV.

• Select the detached part of the bracket and attach it to the wall.

• Use a screw with a diameter of 5 mm or equivalent (not included in the package).

Rear cover

Before selecting the bracket, check the back of the TV to ensure that the screws are not protruding. If they are, the bracket is not attached correctly and the bracket may not be secured properly.

Check

Supported models:

KD-85XG85□□*/75XG87□□*/75XG85□□*/65XG87□□*/ 65XG85□□*/55XG87□□*/55XG85□□*

* In actual model names, the "□□" represents digits or symbols specific to each model.

To the customer

To ensure the safety of the product, Sony strongly recommends that you have the TV installed only by Sony dealers or licensed contractors. Do not attempt to install it yourself.

To Sony dealers and contractors

Pay special attention to safety during installation, periodic maintenance, and inspection of this product.

Proper installation of this product requires sufficient experience, especially in determining whether the wall can support the weight of the TV. Be sure to have this product installed on the wall by Sony dealers or licensed contractors, and strictly follow the safety instructions when performing installation work. Sony is not responsible for any damage or injury caused by mishandling or improper installation.

For safe and reliable installation, refer to the instruction manual for wall-mounted installation, the TV installation guide, and the instructions in this manual.

Safety

Thank you for purchasing this product.

For customers

Installing this product requires sufficient skill. Be sure to contact a Sony dealer or licensed contractor, and observe the necessary safety precautions during installation. Sony is not responsible for any damage or injury caused by incorrect handling or installation, or by installation not intended for this product. This does not affect your legal rights (if any).

For Sony dealers

Installing this product requires sufficient skill. For safe installation of the device, be sure to read this manual carefully. Sony is not responsible for damage or injury caused by incorrect handling or improper installation. After installation, give this manual to the customer.

This installation manual provides important safety precautions and information to ensure reliable connection of the product, which are necessary to prevent accidents. Be sure to read this manual carefully and use the product as intended. Keep this manual for future reference.

Sony products are designed with safety in mind. However, incorrect use of the product may result in serious injury due to electric shock, fire, tipping over, or falling of the product. To avoid such accidents, be sure to follow the appropriate safety precautions.

The date of manufacture is indicated on the product, packaging, or label with a barcode in the following format: YYYY/MM, where YYYY is the year and MM is the month of manufacture.

Manufacturer: Sony Corporation, 1-7-1 Konan Minato-ku, Tokyo, 108-0075 Japan

Authorized organization for accepting claims from consumers in the territory of Kazakhstan: Sony Electronics Representative Office in Kazakhstan, 050010, Republic of Kazakhstan, Almaty, Dostyk Ave., 117/7

Importer in the territory of the Customs Union: JSC "Sony Electronics", Russia, 123103, Moscow, Karamyshevsky proezd, 6

CAUTION

Indicated products

This wall-mount bracket is intended for use with specific TV models. Refer to the TV reference manual to check if the bracket can be used for wall mounting.

For wall mounts

PNEUMATIC

Failure to follow the safety precautions below may result in serious injury or death due to electric shock, fire, tipping, or falling of the unit.

Be sure to contact a licensed contractor, and do not allow children to be near the installation site of the unit.

Improper installation of the wall mount bracket may cause the accidents listed below. For installation, be sure to contact licensed contractors.

The TV may fall and cause serious injury, such as broken bones. If the wall mount bracket is installed on a wall that is uneven, tilted, or not strong enough, the unit may be damaged or cause injury or property damage. The wall must be able to support at least four times the weight of the TV. (To find out the weight of the TV, see the reference guide.) - If the wall mount bracket is installed with insufficient strength, the unit may fall and cause injury or property damage.

Safety precautions regarding children

Do not allow children to climb on the TV or the stand. Keep small parts out of the reach of children so they cannot accidentally swallow them.

For installation or removal of the TV, be sure to contact licensed contractors.

If the TV is transported or removed by unlicensed contractors, it may fall and cause injury or property damage. Make sure that the TV is carried by two or more people (three or more people for TVs with screens 75 inches or larger).

After installing the TV, do not remove the screws, etc.

Otherwise, the TV may fall and cause injury or property damage.

Do not disassemble or modify the parts of the wall mount bracket.

Otherwise, the wall mount bracket may fall and cause injury or property damage.

Do not install any equipment other than the specified one on the bracket.

WARNING: WALL MOUNTING BRACKET IS INTENDED FOR USE ONLY WITH THE SPECIFIED PRODUCTS. IF THE TV IS MOUNTED ON THIS WALL MOUNTING BRACKET WITH EQUIPMENT NOT INTENDED FOR SUCH INSTALLATION, IT MAY FALL AND CAUSE INJURY OR PROPERTY DAMAGE.

To avoid overloading the bracket for wall mounting, do not place anything on it other than the TV. Do not move the TV left/right, up/down.

In that case, the TV may fall and cause injury or property damage.

Do not lean on the TV or hold onto it.

Do not lean on the TV or hold onto it, as it may fall and cause serious injury.

CAUTION

Follow the precautions below. There is a risk of injury or property damage.

Care must be taken to avoid excessive force.

Do not overload the top of the TV. Otherwise, the TV may fall and cause injury or property damage.

Precautions

If the TV mounted on the wall mounting bracket for wall installation is used for a long time, depending on the wall material, the wall behind or around it may become discolored or the wallpaper may peel. - After removing the wall mounting bracket, holes will remain in the wall. Do not use the wall mounting bracket in places with mechanical vibrations.

Do not install the wall mounting bracket on walls where the edges of the TV will protrude beyond the edge of the wall.

Do not install the wall mounting bracket on wall surfaces (e.g., columns) where the edges of the TV will protrude beyond the edge of the wall surface. Hitting the protruding edges of the TV may cause injury or property damage.

Do not install the TV under or over an air conditioner.

If the TV is exposed to condensation or airflow from an air conditioner for a long period of time, it may cause fire, electric shock, or malfunction of the TV.

Securely attach the bracket to the wall, following the instructions provided in this manual.

If any of the screws are loose or missing, the bracket for wall mounting may fall and cause injury or damage to property. When performing installation, be sure to use screws that match the wall material, securely install the device, using no less than four 8 mm screws (or equivalent).

Be sure to use the screws and parts included in the kit for mounting and strictly follow the instructions provided in this installation manual. If other mounting materials were used during installation, the TV may fall and get damaged or cause injury.

Be sure to perform the bracket assembly, exactly following the instructions provided in this installation manual.

If any of the screws are loose or missing, the TV may fall and get damaged or cause injury.

Tighten the screws securely into the designated mounting holes.

Otherwise, the TV may fall and get damaged or cause injury.

Make sure that the TV is not subjected to impacts during installation.

Impacts can cause the TV to fall and be damaged. This may lead to injury.

Install the TV on a wall only if it is flat and perpendicular to the floor.

Otherwise, the TV may fall and cause injury.

After securely installing the TV, ensure that the cables are arranged safely.

Cables that present tripping hazards can cause serious injury or damage to the TV.

Do not allow the power cord and connecting cables to become tangled.

If the power cord or connecting cables are routed between the device and the wall, or are bent or pinched, the insulation of the internal wires may be damaged, which can cause a short circuit or break. This may cause a fire and lead to electric shock.

Brackets, wall mounting brackets for wall mounting, are not included in the delivery set.

When mounting the bracket for wall mounting, use screws that match the material and structure of the wall.

The brackets should be stored in a cardboard box in a dark, dry, clean, and well-ventilated room, away from direct sunlight. Storage temperature: from -20°C to +60°C. Storage humidity: <80%.

Contents

Preparation for installation. 6

Checking the delivery set 6

Determining the installation method 7

Installing the base on the wall 9

Preparing the TV for installation...10

KD-85/75XG85□□, KD-75XG87□□ 10

KD-65/55XG87□□, KD-65/55XG85□□.12

Installing the TV on the wall.14

KD-85/75XG85□□, KD-75XG87□□ 14

KD-65/55XG87□□, KD-65/55XG85□□ 16

Checking the installation 19

Information 19

Specifications. 19

Use the screws for wall mounting SU-WL450 or for mounting the TV on the wall.

Application

Keep the screws in a safe place out of the reach of children.

4 Determine the screw positions for the base (20) A.

See specifications on page 19. If you select point 2-a, use the base adapter hole position ①.

WARNING

The wall on which the TV is to be mounted must be able to support a weight exceeding the weight of the TV by at least four times (to find out the weight of the TV, see the reference guide).

• Determine the strength of the wall on which the TV will be mounted. If necessary, reinforce the wall.

Mounting the base on the wall

• Use four or more screws with a diameter of 8 mm or equivalent (not included in the package). Insert four screws into the holes of the base adapter ①, and attach it to the base (20) A (only 2-a).
• Install the base (20) A horizontally on the wall.

1 Mark the installation location on the wall.

• Use adhesive tape (not included) to mark the position of the TV next to the base or base adapter. See the following table.

Dimensions (mm)

• Remove the tabletop stand from the box. Hold the tabletop stand firmly with both hands while others lift the TV.

KD-85XG85□□

KD-75XG87□□, KD-75XG85□□

• Repeat the instruction and remove the other side of the tabletop stand.

Note

- Detaching the tabletop stand requires at least 2 people. - Be careful not to use excessive force when detaching the tabletop stand from the TV, as this may cause the TV to fall and result in injury or damage to the TV. - Be careful when handling the tabletop stand to prevent damage to the TV. Be careful when lifting the TV, as the tabletop stand may detach and fall, which could cause injury. - Be careful when detaching the tabletop stand from the TV to avoid tipping over the device and damaging the surface on which the TV is placed.

KD-65/55XG87□□,

KD-65/55XG85□

1 Remove the screws from the rear of the TV.

2 Attach the wall-mount brackets and hardware for wall mounting. Perform a check of the mounting hardware according to the "Wall-Mount Bracket SU-WL450" section in "Checking the Accessories" on page 6.

Note

Tighten the mounting brackets securely with screws. - When using an electric screwdriver, set the tightening torque to approximately 1.5 N·m {15 kgf·cm}. Keep the used or unused parts in a safe place for future use. Keep this instruction manual for future reference.

Standard mounting (2-a)

Compact installation (2-b)

Note

When installing the TV, some connectors on its rear panel may be inaccessible.

Connect the necessary cables to the TV.

Before mounting the TV on the wall, be sure to connect the cables. After mounting the TV, connecting the cables will be impossible. See the Reference Guide supplied with the TV.

Note

- For routing cables in a wall-mounted installation. - Before mounting the device on the wall, connect the connecting cables so that they do not interfere.

4 Detach the table-top stand from the TV.

• Remove the table-top stand. Hold the table-top stand firmly with both hands while others lift the TV.

Repeat the above action and remove the other side of the table-top stand.

Note

- To detach the table-top stand, three or more people are required. - Be careful not to use excessive force when detaching the table-top stand from the TV, as this may cause the TV to fall and result in injury or damage to the TV. - Be careful when handling the table-top stand to prevent damage to the TV. - Be careful when lifting the TV, as the table-top stand may detach and fall, which could cause injury. - Be careful when detaching the table-top stand from the TV to avoid dropping the device and damaging the surface on which the TV is placed.

Mounting the TV on a wall

KD-85/75XG85□□，KD-75XG87□□

1 Lift the TV.

The location of the hooks and screws on the base or the base adapter is shown in step 3 of the section "Determining the mounting location" on page 8. - Make sure that the rear panel of the TV is in contact with the base or the base adapter when holding the TV.

• Hold the TV with both hands and make sure the bottom part of the TV is level with the floor. -Carrying the TV should be done by three people: the person in front of the TV should guide the others to place the TV in the desired position.

-When installing the TV on the wall, be careful, especially the person supporting the TV from below, as it may fall and cause serious injury or even death.

2 Install the TV on the base or wall mount base.

• Carefully lower the TV and hook the brackets (B, installed on the rear panel of the monitor) onto the base or wall mount base, following the shape of the holes.
• After installing the TV on the wall, make sure the brackets are securely fixed to the base or wall mount base. Slowly remove your hands and make sure the TV is securely installed.

• After installing the TV on the wall, remove the protective film etc. from the wall.

2-a

2-b

RU

WARNING

• Make sure the TV is supported by two or more people (three or more people for TVs with a screen size of 75 inches or larger when carrying).

Prevent the lower part of the TV from shifting.

• Remove the adhesive tape E and securely attach it to the wall.

• Use a screw with a diameter of 5 mm or its equivalent (not supplied).

Primemechanicals

Check the TV to make sure it does not move forward. If there is a small gap, the TV is not secured properly, and the base or base adapter should be secured more firmly.

KD-65/55XG87□□，KD-65/55XG85□□

1. Place the TV.

The location of the hooks in the base or base adapter mounting holes is shown in Table 3 in the "Determining the mounting location" section on page 8. - Make sure the rear panel of the TV is in contact with the base or base adapter when holding the TV.

Note

• Hold the TV with both hands.

2. Install the TV on the base or base adapter.

• Carefully lower the TV and align the hooks (8) installed on the rear of the monitor with the base or base adapter, following the shape of the holes.
• After installing the TV on the wall, make sure the hooks are securely fixed in the base or base adapter. Slowly remove both hands and make sure the TV is securely installed.

2-a

2-b

↓

↓

RU

• Two or more people are required to carry the TV (for TVs with a screen size of 75 inches or more) when moving it.

Prevent mixing of the lower part of the TV.

• Remove the stand and securely attach it to the wall.

• Use screws with a diameter of 5 mm or equivalent (not supplied).

Note

Gently pull the lower part of the TV towards you to ensure it does not tilt forward. If there is a slight tilt, the TV is not securely fastened, and the strap F should be attached more securely.

• The hooks ⑧ are securely attached to the base or the base adapter.
• The cord and cable are not crossed or pinched.
• Strap F is securely attached without slack.

WARNING

• Incorrect placement of cables, etc., may lead to fire or electric shock due to a short circuit. To ensure safety, make sure all installation steps are completed.

Information

To remove the TV, perform the procedure described above in reverse order.

The remote control keeps the TV in standby mode (when the TV is on or in standby mode, or when the TV is turned on via the remote control with a diagonal of 75 inches or more) during its operation.

Technical specifications

Dimensions: (approx.) [mm]

Unauthorized installation of the TV is not allowed. Follow the instructions for installation, which are not covered here.

It is mandatory to entrust the moving or repair of the TV to qualified personnel who have a license.

Moving or repairing the TV must be performed only by persons, except for qualified personnel who have a license. The TV may fall and cause serious injury or damage. Moving or repairing the TV should be done by at least two people (minimum, if the TV diagonal is 75 inches or more).

Do not unscrew the screws after installing the TV.

If you do this, the TV may fall and cause serious injury or lead to damage.

Do not remove the bracket for wall mounting.

If you do this, the bracket for wall mounting may fall and cause serious injury or lead to damage.

Do not install any other devices other than the specified product.

The bracket for wall mounting is designed for use only with the specified product. In case of installing other devices, other than the specified one, they may fall and break and cause serious injury or lead to damage.

Do not apply the bracket for wall mounting to other TVs. Do not tilt the TV left/right or up/down.

If you do this, the TV may fall and cause serious injury or lead to damage.

Do not touch the TV and do not lean on it.

He can place the TV and not connect it to a new one, because it may fall on you and cause serious injuries.

WARNINGS

If you do not follow the safety instructions below, it may cause serious injuries or damage to the device.

During cleaning and maintenance of the device, do not apply excessive force.

Do not apply excessive force to the top of the TV. If you do, the TV may fall and cause serious injuries or damage to the device.

Safety instructions

If the TV is installed on a wall with partial mounting, it will be used for a long time, so it is necessary to consider the material of the wall, the surface of the wall behind the TV, or the possibility of the wall being damaged or the screws coming out of the wall.

Partial mounting screws must be tightened according to the instructions. Do not use partial mounting screws in places where mechanical stress is present.

Installing the partial mounting bracket

When mounting the partial mounting bracket, use the appropriate screws according to the wall structure and the material it is covered with.

Store the device in a cardboard box, in a dark, dry, clean place with good ventilation, separately from places where acids and alkalis are stored. Storage temperature: from -20°C to +60°C. Storage humidity: <80%.

Contents

Preparation for installation 5

Checking the parts. 5

Determining the installation location. 6

Wall-mounted TV installation

Preparing for TV installation......9 KD-85/75XG85□□, KD-75XG87□□ KD-65/55XG87□□, KD-65/55XG85□□ 11

Wall-mounted TV installation......13 KD-85/75XG85□□, KD-75XG87□□ 13 KD-65/55XG87□□, KD-65/55XG85□□ 15

Checking after installation is complete 18 Additional information 18

Technical specifications 18

Wall-mounted TV installation

The installation procedure depends on the TV model.

To install the TV on the wall, use the SU-WL450 wall-mount bracket.

Preparation

Keep the screws away from children.

Preparation

Installation

• Before installation, carefully read the TV manual and installation guide. Before assembling, make sure you have a Phillips screwdriver that fits the screws.
• Check the installation location of the TV. Use four M8 screws and one M5 screw or equivalent (not included in the package). Choose screws appropriate for the wall material.

Checking the parts

• The stand is included in the delivery set.

AБаза(20)(1)ВШК	В(2)
CГВИNTPSW6x20(4)	DГВИNTPSW4x20i3Втулков(2)
EПрокадka(20)(2)	FРемиь(1)
GВтулka(20)(M4)(2)	HГВИNTPSW4x20(2)
IПерекдддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддддд徳баши(2)	JГВИNTPSW4x10(8)
KПрокадka(60)(2)	LГВИNTPSW6x50(2)
MВтулka(M4)(2)	NГВИNTPSW4x50(2)

Determining the installation location

1. Determine the installation location.

Make sure that the floor has sufficient dimensions and can support the weight, which is several times greater than the weight of the TV.

Information on the required installation of the TV on the wall can be found in the table below. The weight of the TV can be found in the TV's user manual.

Standard mounting

Center of the screen

Dimensions in mm

• If you choose the 2nd method of mounting on the wall, the installation will be limited.

From the installation location, the base of the stand is guided by the table below. If the 2nd method is chosen, skip this step.

Назва модени Розташуванни raков
KD-85XG85□□	a
KD-75XG87□□
KD-75XG85□□
KD-65XG87□□	b
KD-65XG85□□
KD-55XG87□□
KD-55XG85□□

Determine the strength of the wall on which the TV is installed. If necessary, change the wall to a stronger one.

Installation on the wall

Use straight screws with a diameter of 8 mm or equivalent (not included in the delivery set). Screw the screws into the holes on the rear panel of the base ① with the base (20) A (step 2). Install the base (20) A horizontally on the wall.

Mounting points (2nd)

If you use this type of mounting, you cannot use the separate stands for the TV.

Connect the TV to the AC power outlet using the supplied AC power cord.

Before connecting the AC power cord, make sure the TV is installed on the wall. After installing the TV, it will be difficult to connect the AC power cord.

Note for the TV.

The AC power cord must be routed through the wall. Route the AC power cord without stepping on it, and before mounting it on the wall.

Remove the table-top stand from the TV.

Remove one side of the table-top stand at a time. Hold the table-top stand firmly with both hands, while another person lifts the TV.

KD-85XG85□□

KD-75XG87□□, KD-75XG85□□

• Repeat the previous step and remove the other side of the table-top stand.

Be careful when removing the table-top stand from the TV. Be careful not to apply excessive force, as removing the table-top stand from the TV may cause damage to the TV and could result in injury or damage to the TV. -Be careful not to damage the TV with the table-top stand. -Lift the TV carefully, as removing the table-top stand may cause it to tip over and cause injury. -Be careful when removing the table-top stand from the TV. If the stand falls, it may damage the surface on which the TV is placed.

KD-65/55XG87□□

KD-65/55XG85□

1. Attach the TV to the wall using the screws.

2. Secure the wall-mount bracket to the wall. Check that all bracket components are present, using the list "Supplied with SU-WL450" in the "Checking the Parts" section on page 5.

Note

Securely tighten the bracket components with the screws. - For the M6 screws, set the tightening torque to approximately 1.5 N·m {15 kgf·cm}. - Be sure to store the unused components in a safe place for future use. Keep this manual for future reference.

Standard mounting (2-a)

Thin mounting (2-b)

Note

When using this type of mounting, the screws on the rear of the TV cannot be used.

Connect the necessary cables to the TV.

Check the cable connections before mounting the TV on the wall. After mounting the TV, it will be impossible to connect the cables. Note: Refer to the TV manual.

Note

The cable is routed through the wall using a licensed contractor. - Route the cables without stepping on them, and do not mount them on the wall.

4. Attach the stand to the TV.

Remove one side of the stand at a time. Hold the stand firmly with both hands, while another person holds the TV.

• Remove the stand from the TV.

Note

• Be careful not to remove the stand from the TV. If you remove the stand from the TV, it may cause the TV to fall and result in injury or damage to the TV. - Be careful not to damage the stand, so as not to damage the TV. Lift the TV carefully, as the stand may tip over and cause injury.
• Be careful when removing the stand from the TV. If the stand falls, it may damage the surface on which the TV is placed.

Installing the TV on a stand

KD-85/75XG85□□, KD-75XG87□□

1. Lift the TV.

• Align the hooks ⑧, by which the TV is attached to the base or the stand neck, with the holes in the table or the stand. See the table and the section "Determining the installation location".
• Hold the TV and make sure that the hooks of the TV are securely attached to the base or the stand neck.

Note

Hold the TV with both hands. The bottom of the TV should be aligned with the arrow mark. - Hold the TV firmly. The part that protrudes from the front of the TV should be held with both hands to support the TV.

Be careful when installing the TV on a stand. The stand must be strong enough to support the TV. The weight of the TV may cause serious injury or even death.

2. Install the TV on the base or the stand neck.

• Carefully lower the TV and insert the hooks ⑧, which are attached to the back of the TV, into the base or the stand neck (they must match the size of the holes).
• After installing the TV on the stand, make sure that the hooks are securely locked in the base or the stand neck.
• Hold the device with both hands to make sure it does not fall.

To install the device on a wall, remove the mounting bracket (or similar material) from the wall.

2-a

2-b

WARNING

Wall mounting (2-b)

Note.

Wall mounting (2-b)

Note.

Mass (base only): (approx.) [kg]

0.8

Do not place the device in a location where it may be exposed to direct sunlight.

The temperature may rise and cause malfunction. If the ambient temperature is high, the temperature may rise and cause malfunction.

Additional notes

When mounting on a wall, ensure that the wall can support the weight of the device. If the wall is not strong enough, the device may fall and cause injury. After mounting, check that the wall anchors are secure. If the wall is not strong enough, the device may fall and cause injury.

Cable laying crown format

The cables are not laid out in the format for cable laying with a crown.

Cable laying crown format is not laid out in the sections where cables are laid with a crown. If the cable is not laid with a crown, it may be damaged by the cable's own weight.

The cable is not laid out on the surface of the drum.

If the cable is not laid out on the drum, it may be damaged by the cable's own weight, or it may be pulled into the drum or the cable's own weight may cause damage.

Cable laying crown axis

Do not lay the cable with a bend radius less than the specified value.

If the cable is bent at a sharp angle, it may be damaged by the cable's own weight, or it may be pulled into the drum or the cable's own weight may cause damage. The cable material and the drum diameter (or equivalent) must be such that the cable is not bent at a sharp angle.

The cable and the laying accessories must be laid out according to the instructions in this manual. If the accessories are not laid out, the cable may be damaged by the cable's own weight, or it may be pulled into the drum or the cable's own weight may cause damage.

According to the instructions, the cable must be laid out

with a crown.

If the cable is bent at a sharp angle, it may be damaged by the cable's own weight, or it may be pulled into the drum or the cable's own weight may cause damage.

The cable must be laid out with a crown.

If it is not laid out with a crown, the cable may be damaged by the cable's own weight, or it may be pulled into the drum or the cable's own weight may cause damage.

During laying, the cables must not be pulled.

Then connect the AC power cord to the wall outlet.

The TV and the wall outlet should be connected perpendicularly.

If the connection is loose, the AC power cord may overheat or cause a fire.

After connecting the TV, secure the cables properly.

If the wall outlet is damaged or loose, do not use the TV and contact a qualified service person.

The power cord or the cable should not be pinched or bent.

If the power cord or the cable is pinched between the TV and the wall outlet, or if the plug is damaged, it may cause a short circuit, electric shock, or fire. This could lead to serious injury or death.

Do not use the wall outlet for other appliances.

When connecting the TV to the wall outlet, do not damage the plug or the outlet.

Table of Contents

Installing the TV 5

Connecting the TV to the wall outlet 6

Mounting the TV on the wall 8

Connecting the TV to the wall outlet 9 KD-85/75XG85□□, KD-75XG87□□. 9 KD-65/55XG87□□, KD-65/55XG85□□. 11

Mounting the TV on the wall 13 KD-85/75XG85□□, KD-75XG87□□ 13 KD-65/55XG87□□, KD-65/55XG85□□ 15

To install the device

The installation procedure is performed in the following order. To install the device, use the SU-WL450 bracket for installation.

Instructions

• Keep the device away from children, and do not place it in an unstable place.

Installation preparation

Before installation, check the strength of the wall and the installation location. Before drilling, make sure there are no pipes or wires behind the wall. Use a Phillips screwdriver. Mark the installation positions. Use a drill bit with a diameter of 8 mm or larger, and a 5 mm or similar (not included) drill bit for pilot holes. Drill holes in the wall material.

Parts check

Supplied with SU-WL450

Check that all parts are included.

A Heri3 (20) (1) B Terepiik (2)
◎ PSW 6x20 (4) D TbIFbIH PSW 4x20 (2)
E ApaIbIK (20) (2) E	Belenik (1)
◎ TbIFbIH (20) (M4) (2)	H PSW 4x20 (2)
① Heri3ri aIaIaIep (2)	J PSW 4x10 (8)
K ApaIbIK (60) (2) L	PSW 6x50 (2)
M TbIFbIH (M4) (2) N	PSW 4x50 (2)

Marking the installation position

1 Mark the installation position.

Check that there is a suitable location on the wall for the device, and refer to the instructions for the minimum distance from the device to the ceiling.

Refer to the installation template for the wall mounting bracket. Refer to the instructions for the template and the installation instructions.

Standards for installing the screen. Screen installation instructions.

Manual

Ynliri hemipi	Зкразецемерi	Зкразецьим �шемi	Орнау узbihыflu
	a	b	c	d
				Столарты opнау	Жасын opнау
KD-85XG85□□	1909	251	803	142	100
KD-75XG87□□	1673	963	107	595	116 75
KD-75XG85□□
KD-65XG87□□	1450	836	99	523	115 73
KD-65XG85□□
KD-55XG87□□	1231	713	106	468	115 73
KD-55XG85□□

Instruction

The installer is responsible for ensuring that the installation is carried out correctly. Before installation, it is necessary to read the instructions carefully.

Between the current and the previous versions of the instructions, the latest version takes precedence.

Manual

To ensure proper operation and safety, please follow these instructions:

• Do not install the device near heat sources, open flames, or in direct sunlight. Do not place it on soft surfaces such as carpets, beds, or sofas. Do not cover the device with cloth or paper. Install the device in a well-ventilated area.

The device has been tested and approved.

Instruction

The cables should be installed by a qualified technician. Before installation, the power must be disconnected.

To prevent the cables from being damaged, they should be routed with a minimum bend radius of (20) A, and for the main cables ① and the branch (20) E, the branch (60) K, the cables should be secured with clamps.

2. Installation instructions. The installer is responsible for ensuring that the installation is carried out correctly.

2-a Standard installation 2-b Custom installation

Refer to the first step.

2-b TaHdaIraH Ke3e, ApKbI TepMHaIra KaTbIac WKeTeyi 60ana.

3 Heri3ri aanTepdi 6eKity opHbI TypaJIbI TeMeHderi KeCTeDeH KapaHbI3.2-b TaHaJFaH XaFdaNda, OcbI KaamDbI eTKi3in Xi6epiHi3.

Yürgi Hämipi İnmek Öpnbı
KD-85XG85□□
KD-75XG87□□	a
KD-75XG85□□
KD-65XG87□□
KD-65XG85□□	b
KD-55XG87□□
KD-55XG85□□

AanTop ① Heri3iH (PSW 4x10) ② BypaHdaIapbImeH 2-a TaHdaIraH Ke3de (20) A Heri3iHe 6ekity.

4 Heri3di (20) @ opnaty ywiH 6ypaHaJapdbIH opHbIH aHbIKTaHbI3.

18-6eTteri cnaTtAmanapdbkapaHb3.

2-a TaHdaanFaH Ke3Je, ①AaantOp Heri3iHiT Tecik OphbIH naJaIaHbIHbI3.

TeIeIiap opHaTbIaTbH Ka6bIpFa TeIeIiap caIMaFbIHaH TOpT ece aybp CaIcAkbTb KeTepe aNybi TNic (CaIMaFbIH TekcepY yWIn TeIeIiApDbH AhtkTaMaIbIK Hcyckay 6enimKapaHbI3.).

TeIeIiap 6ekITinTIN Ka6bipraHbIH 6epiktiriH aHbIKTaHb3. KaKET 60nca, Ka6bipraHbI XeTKiNkTI TypJe KyweTlH3.

Ka6bipfara TyfbipdbI opHaTy

-Диametpi 8 MM 60nataBH He yKcac Tept Hemece OdaH da KEN 6ypaHaHbI naaanaHbH3 (6epinmereH). ① AanTopbHbH Heri3iHe Tept 6ypaHaJaIapbl (20) A Heri3imEn 6ekitii3 (Tek 2-a). Tfbypbl (20) ka6bipraFA KeIeHeH etin opHaTbIHbI3.

TeJeIaIopHaTyFa DaIbIHdA

Tipek opHaTy HxckaynbIFbIH KapaHbI3.

KD-85/75XG85□□，KD-75XG87□□

1 Install the device on the wall.

Before installation, check the wall surface for suitability, i.e., (for direct mounting) the surface must be flat. Otherwise, use a mounting bracket.

Tools: MM

Yntri hemipi	Белriney Узblдыflы			Зкран optacblblн элшемi
	a	b	c	d
KD-85XG85□□	1909	683	200	251
KD-75XG87□□	1673	468	200	107
KD-75XG85□□

2 Remove the mounting brackets from the device.

3 To install on the wall, use the screws. See the 'SU-WL450 with mounting bracket' section in the 'Mounting the bracket' manual for the mounting procedure.

Note

- Secure the mounting brackets with screws. - When connecting the power cord, leave a distance of 15 cm. - Check that the power cord is not pinched or damaged. Keep this note for future reference.

Standard installation (2-a)

Correct installation (2-b)

Note

- This installation method is not suitable if the wall surface is uneven or if the contacts protrude.

4 Attach the cable(s) to the device.

Before installing the device on the wall, check that the cables are not pinched. After installation, the cables should not be visible. See the installation manual provided with the device.

Note

Connect the cables to the device before mounting. During installation, to avoid damage, secure the cables with clamps.

5. Remove the protective film from the TV.

• Install the TV stand as shown in the figure. Do not install the stand if the TV is placed on a table or other surface.

KD-85XG85□□

KD-75XG87□□, KD-75XG85□□

Remove the protective film from the TV stand before installation.

Note

• The TV stand is heavy. Be careful when lifting it. Do not lift the TV by the stand. When moving the TV, hold the bottom of the TV and avoid touching the screen. Do not place the TV on the stand until the stand is securely attached. If the TV is not properly attached to the stand, it may fall and cause injury or damage.

1. Remove the screws from the back of the TV.

2. Attach the stand bracket to the TV using the screws. For details, refer to the "SU-WL450" installation manual in the "Wall Mount Bracket" section.

Note

- When attaching the stand, be careful not to pinch your fingers. If the TV is placed on a soft surface, the stand may not be stable. - Do not use the stand if it is damaged or missing parts. Keep the stand for future use.

Standard installation (2-a)

Inclined installation (2-b)

Note

- When installing the TV, do not place it on a surface where the TV's back side may come into contact with objects.

3 Connect the cables (cables) to the terminals as shown.

The terminals are designed for connecting cables of the specified type. The terminals are suitable for cables with a certain cross-section. Follow the instructions given with the terminals.

Instruction

Connect the cables to the terminals with the specified cross-section. When connecting, do not bend or damage the cables.

4 Do not pull the cables from the TV.

• When installing the stand, first attach one side of the stand, then attach the other side. When attaching the other side, do not force the stand into place.

Tighten the screws and then attach the other side of the stand.

Instruction

To remove the stand, you will need a screwdriver and a Phillips screwdriver. When removing the stand, be careful not to drop the TV, and keep the screws and other parts in a safe place. To avoid damage, do not remove the stand unnecessarily. When removing the stand, be careful not to pinch your fingers or damage the TV. - When removing the stand, hold the TV firmly and remove the screws as shown in the illustration.

Connecting the TV to the wall

KD-85/75XG85□□，KD-75XG87□□

1 Remove the screws.

Refer to the 3rd step in "Identifying the mounting holes" for the screws on the back or side of the TV. When installing the TV, do not insert the screws into the holes on the back or side of the TV.

Instruction

Install the TV with the screws, and then attach the TV to the wall using the mounting holes. Make sure the TV is level and that the screws are tightened securely.

Temperatures above 60 degrees (temperature, temperature of the hot water), set the temperature for the hot water supply, and the water heater will automatically maintain the set temperature.

2. The temperature should not be set higher than the recommended temperature.

When the temperature is set, the temperature will be maintained within the recommended range, and the water heater will operate accordingly. If the temperature is set higher than the recommended range, the water heater will not operate. To avoid damage to the temperature sensor, do not set the temperature too high.

After the temperature is set, the water heater will automatically adjust the temperature, i.e., it will maintain the set temperature.

2-a

↓

↓

↓

2-b

↓

↓

↓

CHECK

The temperature sensor will automatically adjust the temperature to the set value, and if the temperature is higher or lower than the set value, the water heater will adjust accordingly.

3. Do not set the temperature too high to avoid damage.

• Bend the cables, and secure them with the cable holder.

- Diameter 5 mm cables should be placed in the cable holder (provided).

Start

Before connecting the TV, check the TV's tilt angle against the wall. If it is tilted, the cables may not be secured properly, so secure them firmly.

KD-65/55XG87□□，KD-65/55XG85□□

1 Remove the cables.

For the cables from the base or the wall-mount adapter, refer to step 3 in the "Identifying the mounting location" section on page 7-8. When installing the TV, ensure the cables are not pinched between the base and the wall-mount adapter.

Start

Install the TV with two people.

2 Place the TV on the base or the wall-mount adapter.

After placing the TV on the base or the wall-mount adapter, secure the cables with the cable holder. Ensure that the cables are not pinched between the TV and the base or the wall-mount adapter. To avoid damaging the TV's screen, use both hands to lift it.

2-a

2-b

↓

↓

WARNING

Television sets must be installed at least 75 cm away from the wall. The installation must be carried out by qualified personnel.

Do not remove the rear cover of the television.

• Do not block the ventilation openings.

- Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

NOTE

To prevent the television from tipping over, place the television on a stable surface. If it is not stable, secure it with a wall anchor.

Installation procedure

Follow the instructions below.

Ensure that the antenna and cable are not damaged. - Do not place the TV on an unstable cart or stand. - Secure the TV with a wall anchor (F).

WARNING

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Do not place the apparatus on a cart, stand, tripod, bracket, or table that is not specified by the manufacturer.

Accessories

Follow the installation procedure described in the manual.

WARNING

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Technical specifications

Sony

177

720

Sony

77

77

Sony

0

5 100

• nyn nn nn nn nn, npnnn 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• 6 · 8 9 KD-65/55XG87□11 KD-65/55XG85□
• KD-85/75XG85□□,KD-75XG87□□ KD-65/55XG87□ . KD-65/55XG85□

#

SU-WL450 87 87

(1)(20) (A)(2) 防火手B

18 18. 0792

PSW 4x20 (2)

(4) PSW 6x20 (5)

(2) (20) nniE1) ny

F

nnuuun nnnn nn nnnn nnnn Su-WL450 npnnn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn

(2)PSW4x20 H

(2) (M4) (20) ⑨

.075v07vnnopnnn

，

(2) D D D N D ①

8)PSW4x10 J

(2) (60) nnnn K

2)PSW6x50 L

(2) (M4) ∩ ∩ M

2)PSW4x50 N

	\( \mathrm{n} \)	\( \mathrm{y} \)	\( \mathrm{z} \)	\( \mathrm{w} \)	\( \mathrm{h} \)
	e	d	C	b	a
n	n	n
n	n	n
					1,9091,097KG
					KD-75XG87□□
					KD-75XG85□□
					KD-65XG87□□
					KD-65XG85□□
					KD-55XG87□□
					KD-55XG85□□

a	KD-85XG85□□KD-75XG87□□KD-75XG85□□
b	KD-65XG87□□KD-65XG85□□KD-55XG87□□KD-55XG85□□

.

7n7n

nnpnn nn nnnn 0000000000000000

yinnnnn nn, noon no

(20) nnnn ① v nn, (20) v nn

(60) nnnn

7pn 2x-5y 0oan npnn

（）

.（2-a）A(20)VVA#N①V

.

2-a

2-b

ONnnn,2-a nno ny

· 87

A (20) v'v'v'v (PSW 4x10)

KD-85/75XG85□□, KD-75XG87□□

KD-85/75XG85□□, KD-75XG87□□

1.

B

INO

-

1. A definition of ⑧:

IN D022 ynnnnyNT

3nnn

.

• nnnn(

. npnna

.

n nn n nn nn 8 nn nn nn np by npnn , nn nn

niv 5 vip nn . (pov) Tv

#

400:a

300:b

200:c

100:d

80:e

480:f

100:g

(2-b n) 20 : h1

(2-a nnp) 60 : h2

[1] (7y): (v)

0.8

yynnnn nnny

nppnn nbn nn nn

.

.

Therefore, the area of triangle OBC equals the area of triangle COD plus the area of triangle BOC.

.01

.

77

·

77x 4y

7.1717

7

75

.