WX283.3 - Drill WORX - Free user manual and instructions
Find the device manual for free WX283.3 WORX in PDF.
User questions about WX283.3 WORX
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Drill in PDF format for free! Find your manual WX283.3 - WORX and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. WX283.3 by WORX.
USER MANUAL WX283.3 WORX
- Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA
Type WX283 WX283.3 WX283.9 (280~289-designation of machinery, representative of Cordless Impact Driver)
| Voltage 12V | |
| No load speed | Screwdriver mode 0-600/min |
| Drill mode (Lo-Hi) 0-600/ 0-2200/min | |
| Impact driver mode 0-2200/min | |
| Impact rate 0-3000 /min | |
| Max torque | Impact driver mode 100 N.m |
| Drill mode 15 N.m | |
| Torque setting 22 | |
| Drilling capacity | Wood 20mm |
| Steel 8mm | |
| Chuck type | 6.35 mm (1/4") hex |
| Machine weight | 1.2kg |
NOISE INFORMATION
| A weighted sound pressure | LpA:80.9dB(A) |
| A weighted sound power | LwA:91.9dB(A) |
| KpA&KwA | 3.0dB(A) |
| Wear ear protection when sound pressure is over | 80dB(A) |
VIBRATION INFORMATION
| Vibration total values (triax vector sum) determined according to EN 60745: | |
| Typical weighted vibration | Vibration emission value ah = 3.74m/s2 |
| Uncertainty K = 1.5m/s2 | |
WARNING: The vibration emission value during actual use of the power tool can differ
from the declared value depending on the ways in which the tool is used dependant on the
following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained
Always use the correct accessories for the tool and ensure they are sharp and in good condition.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if it is not managed correctly.
3 in I drill/driver/impact driver EN
WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Helping to minimise your vibration exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti vibration accessories.
Avoid using tools in temperatures of 10^ or less.
Plan your work schedule to spread any high vibration tool use across a number of days.
ACCESSIONS
| WX283 WX | 283.3 WX283.9 | |
| 1.3Ah lithium battery pack | 1 1 / | |
| Charger | 3-5hr 30min / | |
| 2'' Driver bits | 2 2 2 | |
| Hex shank drill bits | 2 2 2 | |
| 10mm detachable keyless chuck | 1 1 1 |
We recommend that you purchase your accessories from the same store that sold you the tool. Use good quality accessories marked with a well-known brand name. Choose the type according to the work you intend to undertake. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.
ADDITIONAL SAFETY RULES FOR YOUR CORDLESS IMPACT DRIVER
- Remove the battery pack from the impact wrench before carrying out adjustments.
- Do not expose to rain or water.
- Do not store the battery pack in temperatures over 40^ .
- Always charge the battery pack between temperatures 0^ to 30^ . Ideal charging temperature is 18^ to 24^ .
- Only use the charger and the battery pack provided no others.
- Avoid short circuit of the battery pack connections (screws & nails).
- Do not incinerate or burn the battery pack, it may explode.
- Do not charge a damaged battery pack.
- Replace any damaged supply cords on your charger.
- Always disconnect the charger power supply before making or breaking the connections to the battery pack.
- Battery pack and charger will be warm during charging, this is normal.
- When not in use, remove a charged battery pack from the charger.
- Always remove the battery pack from the charger immediately after re-charging is completed.
- Your impact wrench and battery pack will be warm when working, this is normal.
- Do not dispose of batteries in fire, or with household waste. Return exhausted batteries to your local collection or recycling point.
- Wear ear protection when operating cordless impact wrench. Exposure to noise can cause hearing loss.
- Accessories and metal parts can become very hot.
- Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
WARNING: If a small amount of electrolyte should leak from the battery pack under extremes of temperature or after heavy use, then wash off immediately from your skin and hands using clean water. For eye contact, rinse thoroughly with clean water and seek medical treatment immediately.
Warnings for the charger:
- Before using the tool, read the instruction book carefully.
- Charger is for indoor use only. Do not expose to rain or water.
- Do not charge non-rechargeable batteries.
SYMBOLS OPERATING INSTRUCTIONS
To reduce the risk of injury, user must read instruction manual
NOTE: Before using the tool, read the instruction book carefully.
Warning
INTENDED USE
The machine is intended for driving in and loosening screws as well as for drilling in wood, metal and plastic.
Wear eye protection
The battery charger supplied is matched to the Li-1on battery installed in the machine. Do not use another battery charger.
Wear ear protection
The Li-lon battery is protected against deep discharging. When the battery is empty, the machine is switched off by means of a protective circuit: The chuck no longer rotates. In a warm environment or after heavy use, the battery pack may become too hot to permit charging. Allow time for the battery to cool down before recharging.
Wear dust mask
When the battery is charged for the first time and after prolonged storage, the battery will only accept approximately 60% charge. However, after several charge and discharge cycles the battery will accept a 100% charge.
Indoor use only
Do not expose to rain or water
Do not burn
Do not dispose of batteries. Return exhausted batteries to your local collection or recycling point
Li
Always charge the battery pack between temperatures 0^ to 30^
B) TO REMOVE OR INSTALL BATTERY PACK (See Fig. A)
Depress the battery pack release button to release and slide the battery pack out from your tool. After recharge, slide it back into your tool. A simple push and slight pressure will be sufficient.
OPERATION
1. INSTALLING OR REMOVING A DRIVER BIT, DRILL BIT OR DETACHABLE KEYLESS CHUCK (See Fig. B)
To install the desired bit or the detachable keyless chuck, pull the collet locking sleeve (7) forward and insert the desired bit or hex shank of the detachable keyless chuck into the sleeve as far as it will go. Then release the collet locking sleeve to secure the bit or the chuck. To remove the bit or the chuck, pull the collet locking sleeve (7) forward and take the tool out firmly.
2. ON/OFF SWITCH (See Fig.C)
Depress the On/Off switch (5) to start and release it to stop your tool. The on/off switch is fitted with a brake function which stops your chuck immediately when you quickly release the switch.
It is also a variable speed switch that delivers higher speed and torque with increased trigger pressure. Speed is controlled by the amount of switch trigger depression.
WARNING: Do not operate for long periods at low speed because heat will be produced internally.
3. SWITCH LOCK
The switch trigger can be locked in the OFF position. This helps to reduce the possibility of accidental starting when not in use. To lock the switch trigger, place the rotation control in the center position.
4. REVERSIBLE (See Fig. C)
For drilling and screw driving use forward rotation marked " lever is moved to the left). Only use reverse rotation marked " (lever is moved to the right) to remove screws or release a jammed drill bit.
WARNING: Never change the direction of rotation when the disk is rotating, wait until it has cooled!
5. CHUCK ADJUSTMENT (See Fig. D)
Detachable chuck is suggested for using in the drill mode.
To open the chuck jaws, firmly hold the rear sleeve of the chuck, and then rotate the front sleeve. Insert the drill bit between the chuck jaws and rotate the front sleeve in the opposite direction. Ensure the drill bit is in the center of the chuck jaws. Finally, hold the rear sleeve of the chuck and firmly rotate the front sleeve in the opposite directions. Your drill bit is now clamped in the chuck.
6. USING THE LED LIGHT
To turn on the light simply press the on/off switch. When you release the on/off switch, the light will be off.
LED lighting increases visibility-great for
dark or enclosed area. LED is also a battery capacity indicator. It will flash when power gets low.
7. FUNCTION MODE SELECTION
The operation of the tool for each application is set with the function mode selection switch (9). To change between functions, slide the function mode selection switch (9) to the desired operating mode as follows:
| 月 | Screwdriver mode (See Fig. E1) |
| 日 | Drill driver mode (See Fig. E2) |
| 星 | Impact driver mode (See Fig. E3) |
WARNING: When using the function mode selection switch, use only when
the tool stops. But when the switch does not easily move, depress the On/off switch slightly to rotate the spindle and then move the function mode selection switch.
Slide the function mode selection switch (9) to mark". Adjust the adjusting ring (8) to the proper torque level for your work.
The torque is adjusted by rotating the torque adjustment ring (See Fig. F). The torque is greater when the torque adjustment ring is set on a higher setting. The torque is less when the torque adjustment ring is set on a lower setting.
Make the setting as follows:
| 1 - 4 For driving small screws | |
| 5 - 9 | For driving screws into soft materi-rial |
| 10 - 14 | For driving screws into soft and hard material |
| 15 - 19 | For driving screws into hard wood |
| 20 - 22 | For driving larger screws |
DRILLING OPERATION
Slide the function mode selection switch (9) to mark
"or The adjusting ring can be aligned in any torque levels for this operation. The drill has a two-speed gear control designed for drilling or driving at LO (mark is or HI (mark is speed (See Fig. E2). When using the drill in the LO speed range, the speed will decrease and the drill will have greater power and torque. When using the drill in the HI speed range, the speed will increase and the drill will have less power and torque.
WARNING: To prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of rotation or the two-speed gear control.
When drilling into a hard smooth surface, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off center as the hole is started. Hold the tool firmly and place the tip of the bit at the point to be drilled. Depress the switch trigger to start the tool. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force or apply side pressure to elongate a hole.
Tungsten carbide drill bits should always be used for concrete and masonry. When drilling in metal, only use HSS drill bits in good condition. Always use a magnetic bit holder (not included) when using short screwdriver bits. When screw-driving, apply a small quantity of liquid soap or similar to the screw threads to ease insertion.
Slide the function mode selection switch (9) to mark "
The adjusting ring can be aligned in any torque levels for this operation.
8. DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle or dispose of the battery pack properly. This battery pack contains
Lithium batteries. Consult your local waste
authority for information regarding available recycling and/or disposal options. Discharge your battery pack by operating your tool, then remove the battery pack from the tool housing and cover the battery pack connections with heavy-duty adhesive tape to prevent short circuit and energy discharge. Do not attempt to open or remove any of the components.
9. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Relieve the load on the machine immediately and allow cooling for approx. 30 seconds at the highest no-load speed.
10. TEMPERATURE DEPENDENT OVERLOAD PROTECTION
When using as intended for the power tool cannot be subject to overload. When the load is too high or the allowable battery temperature of 75^ is exceeded, the electronic control switches off the power tool until the temperature is in the optimum temperature range again.
11. PROTECTION AGAINST DEEP DISCHARGING
The Li-lon battery is protected against deep discharging by the "Discharging Protection System". When the battery is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates.
MAINTENANCE
Your power tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
3 in I drill/driver/impact driver EN
ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authorities or retailer for recycling advice.
DECLARATION OF CONFORMITY
We,
POSITEC Germany GmbH
Declare that the product,
Description
WORX 3 in1 drill/driver/impact driver
Type WX283 WX283.3 WX283.9
(280~289-designation of machinery, representative of Cordless Impact Driver)
Function Drilling, tightening and loosening screws, nuts with a rotary impact mechanism
Complies with the following Directives,
Machinery Directive 2006/42/EC
Electromagnetic Compatibility Directive
2004/108/EC
RoHS Directive 2011/65/EU
Standards conform to
EN 55014-1
EN 55014-2
EN 60745-1
EN 60745-2-1
EN 60745-2-2
The person authorized to compile the technical file,
Name: Russell Nicholson
Address: Positec Power Tools (Europe)
Ltd, PO Box 152, Leeds, LS10 9DS, UK
2012/12/07
Leo Yue
POSITEC Quality Manager
INFORMATIONS RELATIVES AU BRUIT
INFORMATIONS RELATIVES AUX VIBRATIONS
SYMBOLS FONCTIONNEMENT
Model WX283 WX283.3 WX283.9
Directive RoHS 2011/65/EU
Ltd, PO Box 152, Leeds, LS10 9DS, UK
2012/12/07
Leo Yue
Responsible qualite POSITEC
- SELETTORE ROTAZIONE: NORMALE, INVERTITA E BLOCCO
- IMPUGNATURA MORBIDA
- UNITÀ BATTERIA *
- SERRATURA A SCATTO UNITÀ BATTERIA
- TASTO ON/OFF CON VELOCITA VARIABLE
- LUCE FRONTALE
- ANELLO DI BLOCCAGGIO
- UNITÀ BATTERIA
- MANOPOLA DI SELECTIONE FUNZIONI
- MANDRINO RIMUOVIBILE SENZA CHIAVE
DATI TECHNICI
Codice WX283 WX283.3 WX283.9
Ltd, PO Box 152, Leeds, LS10 9DS, UK
2012/12/07
Leo Yue
Tipo WX283 WX283.3 WX283.9
Ltd, PO Box 152, Leeds, LS10 9DS, UK
2012/12/07
Leo Yue
Gestor de Qualidade POSITEC
- KNOP VOOR LINKS OF RECHTS DRAAIEN EN VERGRENDELING
- HANDGREEP MET SOFT-GRIP
- ACCUPACK *
- PAL ACCUPACK
- AAN/UITSCHAKELAAR MET INSTELBAAR TOERENTAL
- WERKLAMPJE
- VERGRENDELINGSBUS SPANHULS
- KOPPEINSTELLINGEN
- FUNCITEMODUS
-
AFNEEMBARE, SLEUTELLOZE BOORHOUDER VAN 10mm
-
Sommige aufgebeidelde of beschreiben toebehoren worden nicht meegeleverd.
TECHNISCHE GEGEVENS
VOORDAT U HET APPARAAT IN BEDRIJ NEEMT
A) HET ACCUPACK OPLADEN
WAARSCHUWING: Verander
WAARSCHUWING: Bedien de
Tipi WX283 WX283.3 WX283.9
Adress: Positec Power Tools (Europe)
Ltd, PO Box 152, Leeds, LS10 9DS, UK
2012/12/07
Leo Yue
Túntoç WX283 WX283.3 WX283.9
(Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK
2012/12/07
Leo Yue
POSITEC Aieutheta nis Nioieta
- NEPEKJIIOYATEJIb HANPABJIEHNBAPOSEHNA BLOKINPOBKN
- MяГКА HAKЛадka HA PYKÖRTKE
- AKKUMYJIATOPHAR BATAPER*
- ΦHKCATOP AKKUMYJIATOPHON BATAPEN
- BbIKJIIOUATEJb C PEGYJATOPOM OBOPOTOB
- NOДCBETKA
- 3AXKIM ZAHROBOFO NATPOHA
- KOJIbIcO PEGYJIHPOBKN KPYTЯUSEO MOMHTA
- ΝEPEKJIIOUATEJIb PEXKIMAPABOTbl
- CbEMHbI BECKJIIOUeBOI NATPOH
TEXHNUECKNE XAPAKTEPNUCTUKN
Mоделew Wx283 Wx283.3 Wx283.9 (280~289-обзачени NHctpymeHTa, BeсрpoBODHо уdapньи NHcTpymeHT)
| Hominahalhoe hapraxeinen 12B | |
| СкорOSTь 6e3 harpy3kn | OTBepToCHbIe 0-600/Min |
| Сберлe"Hne (Lo-Hi) 0-600/ 0-2200/MnH | |
| БесрвоДноу удapны снструмент 0-2200/MnH | |
| Частота удapов 0-3000/MnH | |
| Мakсимальний MOMeHT | БесрвоДноу удapны снструмents 100Hm |
| Сберлe"Hne 15Hm | |
| Peru Pilovka kpyTuJeo MOMeNTa 22 | |
| Мakc. Диаметр Сберлe"Hn | Дерево 20mm |
| Стай 8MM | |
| Зжим патona Шостигранный: 6.35mm(1/4") | |
| Вec 1.2Кr | |
XAPAKTEPNUCTNKN LNYMA
| Звобoe давелене L | pA:80.9Д6(A) |
| Акстеска мошноctь | LWA:91.9Д6(A) |
| КDA&KWA | 3.0Д6(A) |
| Мakсимално довystимoe Звобoe давелене 6e3 Исплбозаня срет CB 3aцпты | 80Д6(A) |
XAPAKTEPNCN BnBpaCNI
BHHMAHNE: Bn6paun, npoun3BoDmma npn pa6oTe mexaHn3IpoBaHHoro IHCTpyMeHTa,
MOKETOTJINuATbcrO3aBnHbIX3HaueHmB3aBNCIMOCTNOTCNO6OBNCIOJIb30BaHn
ycTpOncTb. Hnke nepeuucneHbI HeKOToPbI yCNoBn, OT KOToPbIX 3aBNCIT INHTeHCNBHOCTb Bn6paun:
Cnocob nCnoB3OBAHnI INHCTpyMeHTa I CBOIcTBa O6pa6aTbIbAemoro MaTePnaJa.
CoctoHHe IHcTpymeHTa n ypoBeHb Texo6cnyKnBaHna.
TINNCNOJb3yeMbIX pInHaIeXHOCTe N IX TexHNueCKoe COCTOAHne.
IcnoJIb3yemblpe pa6Oue HNCTpyMeHtbl, COOTBeTCTBnE npIMHeHn IHNCTpyMeHTOB IN Ha3HaueHIO.
При Ненинов образецни дадhoe устpoист bo moke t ctaь пчнho
CnHdpoma npoxKaHn pyK.
BHIMAHHE: TOnTOUHOOeHKBO3DeIcTBnBb6paun BO BpeM 3KcnnyaTaun
Heo6xOIMTO TAKKe yuHTbIBaTb BCE 3TaIpa6Oero npOcecca, BKnHouaBpeMa, KOrda
yCTpoIcTBo BbIKIOueHO INN BKNIOueHO, HO 6e3dEiCTByeT. 3TN nepepbBbl 3HaHTeJIbHO CHINKaIOT oBIIe BnIaHHe Bn6paunB XOJe BCero pa6oeryo zIKna.
Cleyuoune peKomeHuaunn HOMOyT cHn3ntb OaCHOCTB BO3deNCTBn B6paun np pa6oTe.
He BbI6paCbIBAaTe aKKymyIaTOPbI. Bo3BpaTInTe nCNoIb3OBaHHbIe aKymyJIaTOPbI Ha MeCTHbI NyHKT c6opa nn yTuIN3aun
Bcerda 3apjkaite akkymyIaTOp npntemnepaTypax ot 0eC do 30eC.
3KcPJIyATAUЯ
BHIMAHNE: Ipeed nCnoJb3OBAHnEm HnHCTpyMeHTa, BHIMaTeIbHO npOHTaTc TODCTBO NO 3KcNpyatauIN.
ПРИМЕHEHNE NO HA3HAUYEHNIO
DaHbI INCTpyMeHT npeHa3NaYeH dIaBnHcNBAHn I OTBnHcNBAHn 6oTTOB, raeK nDpyrnx pe3b6OBbIX KpeNexKnbIX DeTaJIeN.
NEPEД 3KClIyATAUneH A) 3APJDKA AKKUMYJIaTOPHOJ BATAPEN
3apdHoe yCTPOCTBO,BXODaUeB KOMPTNEKT NOCTABKN, COOTBETCTBYET JNTnEBO-NOHHOJ AKKymyIaTOPHOb 6aTapee,yCTaHOBNeHHoB V np6ope.He nCnoJIb3yIte dpYrue 3apAINbIe yCTPOICTBa.
JIITnEBO-IOHHa AKKymyIaTOPHa 6aTapee 3aUuIeHa OT rIy60KO pa3pArKn. Ppr noIHoH pa3pRJaKe 6bTapeu np6Op BbIKNoUaEtcra NocpeDCTBOM 3aUHTHOJ cENN. NaTPOH IHCTpyMeHTa NepeCTaHET BpaUaTbcra. B YcIOBnx IOBbIeHHoT Tempepatypbl n Nocne dINTeBHORO nCNOb3OBAHnra 6bok 6bTaapei MoXe T nepePebcra H He 3apXKaTbcra. DaTe aKKymyIaTOPHOb 6bTaapee OCTbITb nepeD 3apAko.
Pi np nepBoi 3apRdke aKKymyIaTOPHOH 6bTapeu nn Iocne dINTeBHoro XpaHeHnA kKymyIaTOPHa 6bTaapee MoXe T apAInTBcra TObko Ha 60% . Ondako nocne HeCKoJIbKnx UNKIOB 3apRdKn i pa3pRKn aKKymyIaTOPHa 6bTaapei NoNHOCTbO 3apAInTCsR.
B) CHYTNE N YCTAHOBKA AKKUMYJIATOPHOI BATAPEI (Pnc.A)
Haxmte Ha qKcTOp aKKymJrTOpHO
6aTapeu n n3BneKeTe ee n3 dpEn. BCTabBe
3apXeHHyO aKKymJrTOpHyO 6aTapeo B dpEn.
Ira qKcaun 6aTapeu docTaTOUHO JERKORO
HaKaTna.
3KcPJIyATAUa 1.BCTABKA DEPJXABKN PE3Ua, MYΦTbI NJIH HAKOHEYHnKA OTBEPTKn /N3BJIeYEHNE DEPJKATEJIHACADOK,HACADKN IOD TAIKY NIIH OTBEPTKn (Pnc. B)
TOnrHnTe 3aXnM ZaHroBOro NaTpoHa Bnepe.
IOnHOCTbIO BCTaBbTe Tpe6yeMyIO HacaIKy BV aTPOH IOTNcyTIne 3axIM ZaHROBOrO NaTPOHa. NotAHnte 3axIM ZaHROBOrO NaTPOHa (7) Bnepei. N3BJIeknTe HacaIKy IV3 NaTPOHa IOTNcyTIne 3axIM ZaHROBOrO NaTPOHa.
2. BbIKJIIOUATEJIb C ΦYHKLIneH TOPMO3A (Pnc. C)
HaxmteIbBkUoyehnIOTnyCTnte
IbBbIKNooyehnBaWero IHcTpymeHTa.
BbIKNoayTeIb OChauen FyHKuueN TopMo3a,
KOTopra HeMeJneHNO OCTaHaBnBaet NaTPOH,
KOrda Bbl 6bICTPO OTNyCKaete BbIKNoayTeJIb.
Takke cyuectByet nepeKluoyateJIb
peYlnpyemO CKOpocTN, KOTOpBIObeCneuBAET
6oIb7yO CKOpocTb N cKpyuBaIoUIM MOMHT C NOBbIweHHbIM ycInnEM cnyska.CkopocTb
peYlnpyETcKOLNuYeCTBOM cnYCKOB KypKa
pepeKluoyaTeJIa.
BHMAHNE: He pa6oTaIe
ДПИТБHoe BpEma Ha MaNoI
CKOPOCTN, 3TO MOXET npHBECTN K neperpeBy HhctpyMeHTa.
3.БЛOKИРОВКABbIKJIIOUATEJIЯ
BbIKHouateJIb MoKHO 3a6JIOKIpOBaTb B
BbIKHIOueHHOM NIOJOKeHN. 3TO N03BOJAreT
NCKIQUHTb BepoARTHOCTb CnyauHORO
BKIOUeHn, KOrDa INHCTpyMeHT He NCNOB3yETcra.
IJa 6JIOKIPOBKn BbIKHIOuATEJe yCTaHOBNTe
NepeKJIIOUaTeJIb HAnpaBHeHn BpaUeHnBa
CpeDHee NOIOXeHne.
4. ΠEPEKJIIOUATEJIb HANPABJIeHnB BPAUeHnR(PNC.C)
Дя CBepJIeHnI BBepTbIBaHne BInTOB
NcNoJIb3yIte BpaIeHne BpePeI, O6O3HaueHHOe
"（pbIur NOBepHyT BNeBO).NcNoJIb3yIte
ToIbKO O6paTHOE BpaIeHne, O6O3HaueHHOe
"D(pbIur NOBepHyT BnpaBO)ДЯ yJaJIeHnI
BInTOB INIocBO6OxJdeHnI 3aCTpRbWeI rOJOBKn
CBepIIa.
BHUMAHNE: Hnkorga He n3MeHnTe HanpaBneHne
Bpauhenn npn BpaaioeMcnaTpoHe, doxntecb ero noHOn octahOBKn!
5.БыICTPO3AXHMHOI NATPOH (Pnc.D)
CbeHbI natoH peKOMeHyetycNcNoMb3OBaTb BpeXMe CBePJIeHnI.
3a6IokpyuTe 7nnHdJIb, yCTaHOVB
IpeKluOyateIb HApBaJIeHnI DBrJKeHnB
CpeDHee nIOJKeHne. IInr OTKpbITnR KUaKOB
NaTPOHa npOBepHnte erO nepeHIO uactb
IpoTINb YacBOoB CTpeIKn. BCTaBbTe CBePNo
MeJdy KUaYkAMn NaTPOHa NpOBepHnte
IpeEHNIO UAcTb NaTPOHa B O6paTHOM
HaNPabJIeHn. Y6eNITcB, YTO CBePINO
HaxODNTcB U cHTpe KUaCKOB NaTPOHa. 3aTEM
3aTaNITE C yCNIIeM NepeHIO UAcTb NaTPOHa
no YacBOoB cTpeJIke.Tenepb CBePINO HaJeKHO
3aXaTO B NaTPOHe.
6. Побсветка
ДяВКIOUeHЯ NOcBcTKn HaxMNTe N ydeKINBaIte BbIKIOuateJIb. IocBcETKa BBKIIIOHTCra, KOrda Bbl OTNcyTnte BbIKIOUaTeJIb. CBeToIOIDHaJ IOcCBETka OCEucaet TemHbie INN 3akpbItbe oBlaCTn. CBeToIOJrYBnIeTc TaKke INDkATOpOM eMKoCTn 6aTapeN. PpN pa3PJe 6aTapeN OH NaHHaet MIRatb.
7. BbIEOP PEXKIMA PAEBOTbl
Pexm pa60bpeyKTopa JnKoHKeTHbix ycnoBn 3Kcnnyatauyn yctaHaBnBaetcnaepekIIOUaTeMe (9) Bb6opa peXmMa pa60bI. IJnpeekIoueHnA cyHKnepemeuaTe nepeKJIIOUaTeIb peXmOB (9) B Tpe6yEmoe nOIOxHe, KAK NOKa3aHO HIXe:
Pn HcNoIb3ObaHnn No Ha3HaueHnIO
3NeKtpOnHCTpyMeHT He MoXeT 6bITb NpeepyKeH.
Pn BbICOKo HarpY3Ke IIN NpEbIiSeHnN
DOnyCTmOn TeMnepaTypbI aKKymJrTopaB 75^ 3NeKtpOnHka BbIKIOuHaET 3NeKtpOnHCTpyMeHT,
Noka OH He OCTbIHet Do ONTImaJIbHOro
DInana30Ha pa6Oueh TempepaTypbI.
COBMECTHMOCTU 2004/108/EC
Дирекпва Дд RoHS 2011/65/EU
I cTaHdapTaM
EN 55014-1
EN 55014-2
EN 60745-1
EN 60745-2-1
EN 60745-2-2
JIuO C npaBOM KOMnInpOBaHna DaHHoro TexHueckoro faHa,
Имя: Russell Nicholson
Ampec: Positec Power Tools (Europe)
Ltd, PO Box 152, Leeds, LS10 9DS, UK
2012/12/07
Leo Yue
Mehedkep no KaueCTby POSITEC
