BFT122F - Screwdriver MAKITA - Free user manual and instructions

Frequently Asked Questions - BFT122F MAKITA

USER MANUAL BFT122F MAKITA

Explanation of general view

1 Battery cartridge	9 LED indicator	17 Bit
2 Button	10 Adjusting ring	18 Sleeve
3 Red part	11 Ring	19 Range of fastening capacity
4 Indicating lamp	12 Scale	20 Revolution angle (°)
5 Capacity	13 Adjusting grip	21 Torque (N·m)
6 Switch trigger	14 Hole for adjusting grip	22 Limit mark
7 Reversing switch lever	15 Yellow line	23 Brush holder cap
8 Front lamp	16 Compression spring	24 Screwdriver

SPECIFICATIONS

Model BFT020F		BFT021F	BFT040F	BFT080F	BFT122F	BFT042F	BFT081F	BFT123F
Fastening torque (N·m)	Hardjo	nt 0.5-	2 0.5-2	1-4 3-8	5-12 1	-4 3-8	5-12
	Soft joint	0.5-2	0.5-2	1-3.5	3-6.5	5-10	1-3.5	3-7.5	5-12
No load speed (min-1)		540	320	950	540	320	1,200	700	390
Dimensions		200 x 65 x 251 mm (with Battery Cartridge BH9020/BH9020A)					200 x 71 x 242 mm (with Battery Cartridge BH1220C)
		200 x 65 x 274 mm (with Battery Cartridge BH9033/BH9033A)					200 x 71 x 251 mm (with Battery Cartridge BH1233C)
Net weight		1.4 kg					1.5 kg
Rated voltage		D.C. 9.6 V					D.C. 12 V

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

ENE033-1

Intended use

The tool is intended for screw driving in wood, metal and plastic.

ENF002-1

Power supply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire.

GEAO10-1

General Power Tool SafetyWarnings

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

GEB050-2

1. Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
2. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.

A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

1. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50^ (122^) .
2. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
3. Be careful not to drop or strike battery.
4. Do not use dropped or struck battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 10^ - 40^ (50^ - 104^) . Let a hot battery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.

Installing or removing battery cartridge

• Always switch off the tool before insertion or removal of the battery cartridge.

For Models BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Fig. 1)

• To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.

• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

For Models BFT042F, BFT081F, BFT123F (Fig. 2)

• To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge.
• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

Refresh charging

Refreshing battery adapter (optional accessory) can refresh an inactive battery cartridge.

• Refresh charging should be done once a week.
• When you charge a new battery cartridge or a battery cartridge that has not been used for a long time, it may not accept a full charge. In this case, refresh charging must be done. The battery cartridge may decrease the tool performance, because the chemical substance of the battery cartridge is inactive.

Checking the remaining battery capacity (Fig. 3)

For BH9020A, BH9033A

When charging

When the charging begins, the first (far left) indicating lamp begins to flicker. Then, as charging proceeds, the other lamps light, one after the other, to indicate the battery capacity.

When using

When the tool is switched on, the lamps will light after 2 seconds to indicate the remaining battery capacity. When the tool is switched off, the light goes out. If the battery has not been used for a long time, or is needed refresh charging, the orange lamp begins to flicker. Use Makita refreshing adapter to refresh the battery.

CAUTION:

• A battery cartridge extracted from the charger that has been unplugged with the battery cartridge inserted does not indicate the battery capacity due to its protective function even if the tool is switched on after the battery insertion into the tool.

At this time, recharge it for about five seconds before use.

NOTE:

• Please contact Makita Authorized Service Center if the warning lamp of the battery cartridge does not light up when using or charging.

Switch action (Fig. 4)

CAUTION:

• Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released.

To start the tool, simply pull the switch trigger. Release the switch trigger to stop.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
• When not operating the tool, always set the reversing switch lever to the neutral position.

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation.

When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.

Lighting up the lamps (Fig. 6)

CAUTION:

• Do not look in the light or see the source of light directly.

Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The light automatically goes out 10 seconds after the switch trigger is released.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.

LED indicator (Fig. 7)

The lamp on the tool shows the following functions.

Function Status		Status of the LED indicator/beeper		Action to be taken
		LED indicator	Beeper
Auto-stop fastening	This function works when the tool has reached the preset fastening torque and normal tightening has been completed. This helps overtightening to be avoided.	Lights up in green for approximately one second.	— —
Delayed re-start	For approximately one second after auto-stop fastening, the tool does not start even if the switch trigger is pulled.
Warning against insufficient fastening	Insufficient fastening has been performed when the switch trigger has released before reaching the preset fastening torque.	Lights up in red.	A long beep	Retighten the screw.
Warning for battery cartridge capacity	This indicates the appropriate time to replace the battery cartridge when the battery power becomes low.	Flickers in red slowly.	A series of long beeps	Replace the battery with fully charged one.
Checking the remaining battery capacity, Autostop	This function works when the battery power is almost used up. At this time, tool stops immediately.	Lights up in red.	A long beep	Replace the battery with fully charged one.
Check the LED indicator, light and beeper operation	This function works to check the proper operation of the LED indicator, light and beeper when a battery cartridge has been inserted into the tool.	Lights up first in green, next red. (And then the light comes on.)	A series of very short beeps	—
Anti-reset of controller	This function works when an abnormal drop of the battery voltage occurs for some reason, and the tool stops.	Flickers in red and green alternatively.	A series of short beeps	Replace the battery with fully charged one.
Overheat	This function works when the temperature of the controller goes up very highly, and the tool stops.	Flickers in red quickly.	A series of short beeps	Remove the battery cartridge immediately and cool the tool down.
Operation error of the switch trigger	This function works to avoid the tool's immediate start upon insertion of battery cartridge into the tool with the switch trigger being pulled.	Flickers in red and green alternatively.	A series of short beeps	Release the switch trigger.

Adjusting the fastening torque (Fig. 8 & 9)

When you wish to drive machine screws, wood screws, hex bolts, etc. with the predetermined torque, adjusting the fastening torque as follows.

1. First remove the battery cartridge from the tool.
2. Loosen and remove the screw that secures ring.
3. Rotate the ring in the front of the tool by hand so that a hole can be seen below the ring.
4. Place the battery cartridge in place and pull the switch trigger. Release it so that the adjusting ring rotates and becomes visible in the hole. And then remove the battery cartridge.
5. Use an optional adjusting grip to adjust the fastening torque. Insert the pin of the adjusting grip into the hole in the front of the tool. And then, turn the adjusting grip clockwise to set a greater fastening torque, and counterclockwise to set a smaller fastening torque.
6. Align the yellow line with your desired number on the fastening torque scale.
7. Insert the battery cartridge and be sure that a fastening torque has been set up by using a fastening torque tester.
8. Rotate the ring in front of the tool and then tighten the screw to secure the ring.

NOTE:

• Numbers on the fastening torque scale is a guideline to set up your desired fastening torque.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

Installing or removing driver bit or socket bit (Fig. 10 & 11)

Use only the driver bit or socket bit shown in the figure. Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above.

OPERATION

Screwdriving operation (Fig. 12)

Place the point of the driver bit in the screw head and apply pressure to the tool. Then switch the tool on. When the clutch cuts in, the motor will stop automatically. Then release the switch trigger.

NOTE:

• Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged.

Limits of fastening capacity (Fig. 13, 14, 15, 16, 17, 18, 19)

Use the tool within the limits of fastening capacity. If you use the tool beyond the limits, the clutch does not work. And the tool cannot deliver enough fastening torque.

NOTE:

• The revolution angle means the angle which a screw/ bolt revolves when the tool attains to 100% from 50% of desired torque.
• Use of a low temperature conditioned battery cartridge may sometimes give warning for battery cartridge capacity by warning lamp and beeper which makes the tool stop immediately. In this case, the range of fastening capacity may be inferior to those shown in the above even if a charged battery cartridge is used.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

Replacing carbon brushes

Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. (Fig. 20)

Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. (Fig. 21)

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

ACCESSIONS

CAUTION:

• These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
• Various type of Makita genuine batteries and chargers
  Automatic refreshing adapter
• Adjust grip
• Protector
• Grip Base Set
  Grip 37
• Anti kickback head

Noise

The typical A-weighted noise level determined according to EN60745:

Model BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Sound pressure level (L_pA) : 70 dB (A) or less Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A) Model BFT123F

Sound pressure level (L_pA) : 71 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745:

Work mode: screwdriving without impact

Vibration emission (a_h) .. 2.5m / s^2 or less

Uncertainty (K): 1.5m / s^2

ENG901-1

• The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
• The declared vibration emission value may also be used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s):

Designation of Machine: Cordless Screwdriver

Model No./ Type: BFT020F, BFT021F, BFT040F,

BFT042F, BFT080F, BFT081F, BFT122F, BFT123F are of series production and

Conforms to the following European Directives: 2006/42/EC

And are manufactured in accordance with the following standards or standardised documents:

EN60745

The technical documentation is kept by our authorized representative in Europe who is:

Makita International Europe Ltd.

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

Tomoyasu Kato Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Descriptif

(Fig. 13, 14, 15, 16, 17, 18, 19)

Modèle BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, Angleterre

30.1.2009

Tomoyasu Kato
Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Übersicht

Für Modelle BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Abb. 1)

Modell BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

Tomoyasu Kato Direktor

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Visione generale

Modelli BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Fig. 1)

(Fig. 13, 14, 15, 16, 17, 18, 19)

Modello BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Livello pressione sonora (L_pA) : 70 dB (A) o meno Incertezza (K): 3 dB (A)

Modello No./ Tipo: BFT020F, BFT021F, BFT040F,

BFT042F, BFT080F, BFT081F, BFT122F, BFT123F

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

Tomoya su Kato

Aministratore

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

NEDERLANDS (Originele instructies)
TECHNISCHE GEGEVENS

(Fig. 13, 14, 15, 16, 17, 18, 19)

Model BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Geluidsdrukniveau (L_DA) .. 70~dB Aoflager

Onnauwkeurigheid (K): 3 dB (A)

Modelnr./Type: BFT020F, BFT021F, BFT040F, BFT042F,

BFT080F, BFT081F, BFT122F, BFT123F

in sériearend geproduceden

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

(Fig. 13, 14, 15, 16, 17, 18, 19)

Modelo BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Nivel de presión sonora (L_pA) : 70 dB (A) o menos Error (K): 3 dB (A)

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, Inglaterra

30.1.2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Explicaçao geral

Para os Modelos BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Fig. 1)

Acender as Iampadas (Fig. 6)

PRECAUÇA:

Modelo BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Nivel de pressao de som (L_pA) : 70 dB (A) ou inferior VariabilitadE (K):3 dB A

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, Inglaterra

30.1.2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

For model BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Fig. 1)

For model BFT042F, BFT081F, BFT123F (Fig. 2)

Model BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Lydtryksniveau (L_pA) : 70 dB (A) eller mindre Usikkerhed (K): 3 dB (A)

Model nr./Type: BFT020F, BFT021F, BFT040F, BFT042F,

BFT080F, BFT081F, BFT122F, BFT123F

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

Tomoyasu Kato

Direktør

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

For modellerna BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Fig. 1)

Modell BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Ljudtrycksniva (L_PA) ..Hogst 70 dB (A)

Osakerhet (K): 3 dB (A)

Bullernivan under pagaende arbete kan overstiga 80 dB (A)

Modell BFT123F

Ljudtrycksniva (L_pA) : 71 dB (A)

Osakerhet (K): 3 dB (A)

Bullernivan under pagäende arbete kan overstiga 80 dB (A).

Bär hörskéyydd

ENG900-1

Vibration

Vibbrationernas totala varde (trippelaxial vektorsumma) bestamid enlighet med EN60745:

BFT080F, BFT081F, BFT122F, BFT123F

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

For modellene BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Fig. 1)

Modell BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Lydtrykkniva (_) : 70 dB (A) ellr minred Usikkerhet (K):3 dB A

Under bruk kan støynivæt overskride 80 dB (A) Model BFT123F

Lydtrykniva (L_PA) : 71 dB (A)

Usikkerhet (K): 3 dB (A)

Under bruk kan stynivaret overskride 80 dB (A).

Bruk horselvern

ENG900-1

Vibrasjoner

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

Tomoyasu Kato

Direktor

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Yleisselostus

Mallit BFT020F, BFT021F, BFT040F, BFT080F, BFT122F (Kuva 1)

Malli BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Aänenpainetaso (L_pA) : 70 dB (A) tai alle Epävarmuus (K): 3 dB (A)

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30.1.2009

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Tevikc npoeiobonoiaeic aoaaliaac yia to nEkrpiK epyaaleio

IPOEIAOIOIHsH Aiaaota e ae TIC npoioioeic aoaaiac kai oae TIC odnyiec. H un tnpon twv npoeioioewv kai oyniw evextal va kaataa 念 e nektpoanxi, npkayia n/ka oapo tpaumatuo.

ΦuaTe oAe TIC pOeIbOIOInoeic KAI TIC OOnyieS Yia eAAovTik npapnoH.

GEB050-2

AΣYPMATO KATΣABIΔI — ΠPOEIΔΟΝΟΙΗΣΕΙΣ AΣΦΑΛΕΙΔΣ

(EIK. 13, 14, 15, 16, 17, 18, 19)

Xpnooioite to epyaeeio oea ota opia tnC ponnc otepewonc. Eav xpnooionoiote To epyaeeio npav twv oiwv autov, o uunkntc ev 0eitoupyei kai to epyaeeio dEv tha unopei va anodooeapketn poin tepewonc.

\SHMEIΩS:H

H ywvia nepiortpohnsivaln ywvia tnv onoia ma iδa / moulovi diaypapεi otav to epyaaleio havει oto 100% ano to 50% tnc επuμntnc pointc.
Hxphon mia ckaetac matapiae eupokoevcn 0e xamn thepuokpaia nopei kauia fopa va evepyonoiot o aanaki npoioiOnnc kal tonxnt yia avapkeia foptionc matapiaacou avaykacovu to epyaio va otatnoe i aeooc. Tny nepintwn autn, n tun tnC poinc otepewonc th aival katwtern ano autn nou faivetai napanaw akoun kai av xpnouonoihei foptiouvnaetaa natapiac.

ΣYNTHPH∑H

IPOEOXH:

• Piv tv E kTeEon Epyaowv e Tn ouakeun δiaeβaiwveoTne nvtote, yia to ot n ouakeun σθnoTnke e anouakpuoevo to ouawpeutn.
  Mny xnpaunoiite note bEvzivn, ntpeiaiko aIepa, daiutiko, akkooan npapouoe ouiec. Evexetai va npokn0i anoxpwataooc npapaopphion npwyc.

AvtikataoTaon Kapbouvákia

Apaieite kai eEyxTe TIG yKtpc avpako taktia. Avikataote otav apouv expi to onaabi opiou. Kpatate TIG yKtpc kaapc kai eUthetapec va yluotpou vOtic kec. Kai oio yktpc avpaka npenei va avikaoiatavtai tauoxpova. Xpnouonoite Movo tautoonuec yktpec.(Eik.20)

Xpnoiopoioite eva katoaibi yia va aphipeite ta kanakia tnc 0nkns npktpac.Apaipote TIC 0apuevec npktpec, baTe TIC kaivoupyiec kal a0phiaiote ta kanakia tnc 0nkns npktpac. (Eik.21)

TnV diatnpn TcA ZFAEIAZ KAI AIONIISTIA TOU npoiovtoc, EIOKEUEc, OONIAHNOte aALN Ouvtnpnon npuOuon npenei va kTeLouvtai ano Ta EEOUIOBOTneva Kevtpa EEUINPETNOnc TNC Makita, eXpnon naVTote avtaalaktwv Makita.

EAPTMATA

PPOEOXH:

Auta ta eApntmuata npooaptmuata ouviotovtai yia xpmon To epyaaleio Makita nou nepiypapntke otic oonyies autc. H xpmon otiodnone aalww eApntmuatwv npoopaptmaowu npoei va npokaleoikivuo tpaumauou ae atota. Xpmonoiite Ta eApntmuata npoopaptmuata movo yia tnV xpmon nou npoopiciovtal.

Eav xpeiazote onoiadnoote Bontheia yia nepiaoatepcnnpofoipc oexan eauta ta EApntmuata, anotavtheta oto toniko oac kevtpo Eunnpetnonc Maika.

• i o p o l TUNoI auθεvτικων μηατapiων kal φορτισών MaKITA.
• PpOaPooTnc autoatanc avaveowns
• Puθμισικήλαβή
• PpOoTaTeUtiKo
• v o o a n c a n s
  AaBn37
  Kεφαλή κατά της avακρουσης

Oópuβoc

To tuniok A einnieo p opuBou kathetai aouwva u EN60745:

Movελo BFT020F, BFT021F, BFT040F, BFT042F, BFT080F, BFT081F, BFT122F

Movi yia xwpeC TnEupwnns

Anwann Suumopphiog EK

H Makita Corporation, o une uvoKataokekuaotnc, otTo/Ta akolouo(a) mnxdvmaTq TnC Makita:

Xapaktnpiaoosnaxavmaotc: Aoupato katoaibi Ap.ovteAou/Tuno:C BFT020F,BFT021F,BFT040F, BFT042F,BFT080F,BFT081F,BFT122F,BFT123F eivai ev oipapaywn

oumuopfoovotai TIC aKoAouOeEupwnaiKc OdyieC:

2006/42/EK

kai kataokeuaocovta oufova u ta akoloutheta npotuna n eyypaa tunonoinongc:

EN60745

H TExvikn Tekunpiwn Ouaoetai ano Tov Eouioobotnuevo Eknpoosno mac otnv Eupwn, olambdaon tn:

Makita International Europe Ltd.

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England (Ayylambda)

30.1.2009

Tomoyasu Kato

△ieuθuvtns

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Makita Corporation

Anjo, Aichi, Japan

884500D993

IDE

www.makita.com