DB 2709 - Kitchen appliance CLATRONIC - Free user manual and instructions

USER MANUAL DB 2709 CLATRONIC

General Safety Instructions

Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use. Do not use it outdoors (except if it is designed to be used outdoors). Keep it away from sources of heat, direct sunlight, humidity (never dip it into any liquid) and sharp edges. Do not use the appliance with wet hands. If the appliance is humid or wet, unplug it immediately. Do not put it in water. When cleaning or putting it away, switch off the appliance and always pull out the plug from the socket (pull on the plug, not the cable) if the appliance is not being used and remove the attached accessories. Never leave the appliance unsupervised. To protect children from the dangers posed by electrical appliances, make sure that the cable is hanging low and that children do not have access to the appliance. Check the appliance and the cable for damage on a regular basis. Do not use the appliance if it is damaged. Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have a faulty cable be replaced only by the manufacturer, by our customer service or by a qualified person and with a cable of the same type. Use only original spare parts. Pay careful attention to the following “Special Safety Instructions“. Special Safety Instructions

WARNING! The ironing base becomes hot very quickly and takes a long time to cool down. Please do not touch it. When the iron is not in use it should be placed on its stand. Before filling the water tank remove the mains lead. Please do not fill the water tank higher than the MAX mark. First Use of the Machine Numbering of the Controls

Temperature regulator Control lamp Spray button Control lamp – automatic switch-off Steam quantity regulator

Filler opening for the water tank Spray nozzle Water level indicator Steam jet button Sliding mechanism for closing the filler hole

07.05.2002 10:04 Uhr

Seite 28 Clean the ironing base with a slightly damp cloth. Fill the water tank through the filling hole (6) with normal water (up to a hardness degree of 2). In case of water with a higher degree of hardness, use distilled water. Use the filling container. Using the Device ATTENTION: Only garments are to be ironed with this device. Ironing without steam (steam jet regulator on 0).

1. Place the device on its stand.

2. Electrical connection

Make sure that the iron voltage (see name plate) and the line voltage match.

3. Sort the laundry according to ironing temperature. Start from the lowest

temperature to be set with the thermostat: synthetics, silk (low temperature) wool (medium temperature) cotton, linen (high temperature)

4. Insert the plug in a duly installed 230V/50Hz socket with protective contact.

5. The LED lights up. As soon as it shuts off, the set temperature is reached

(approximately 3 min.). Now you can start to iron.

6. Always pull the plug out of the socket after using the iron.

Open the filler opening. Then fill the tank with water and close the filler hole. For this a high temperature is needed (cotton, linen). The quantity of steam can be regulated using the steam quantity regulator (5). Extra steam can be added with the steam jet function (9). Vertical Steam: This can be used to produce a jet of steam in a vertical direction. Self-Clean (

1. Fill about half the water tank with water.

2. Heat the device to the max. temperature. When the LED shuts off, unplug the

3. Now hold the machine horizontally above a sink, turn the steam quantity control

to the self-cleaning symbol and rock it to and fro until the tank is empty. Then turn the control back to "0".

4. Place the iron back on the stand and heat it again. To clean the soleplate, pass

the iron on a clean cotton cloth. Spray function to dampen a spot to be ironed, press the spray button (5).

07.05.2002 10:04 Uhr

Seite 29 Cleaning and Storage

Always remove the mains lead before cleaning! Clean the casing with a slightly damp cloth. Clean the iron with a slightly moist cloth. In order to prevent the water from leaking, always ensure that the sliding mechanism of the filler hole is closed. This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations. Subject to technical changes without prior notice! Guarantee The device supplied by our Company is covered by a 24 month guarantee starting on the date of purchase (receipt). During the life of the guarantee any fault of the device or its accessories *) ascribable to material or manufacturing defects will be eliminated free of charge by repairing or, at our discretion, by replacing it. The guarantee services do not entail an extension of the life of the guarantee nor do they give rise to any right to a new guarantee! Proof of the guarantee is provided by the proof of purchase. Without proof of purchase no free replacement or repair will be carried out. If you wish to make a claim under the guarantee please return the entire machine in the original packaging to your dealer together with the receipt. *) Damage to accessories does not mean automatic free replacement of the whole machine. In such cases please contact our hotline. Broken glass or breakage of plastic parts are always subject to a charge. Defects to consumables or parts subject to wearing (e.g. motor pistons, kneading blades, drive shafts, spare remote control, spare toothbrushes, saw blades, etc.) as well as cleaning, maintenance or the replacement of said parts are not covered by the guarantee and hence are to be paid! The guarantee lapses in case of unauthorized tampering. After the expiry of the guarantee After the expiry of the guarantee repairs can be carried by the competent dealer or repair service against the payment of the ensuing costs.

07.05.2002 10:04 Uhr