PS 1002 Niro - Heating appliance EINHELL - Free user manual and instructions

Product Type	Fan Heater
Power Output	2000 W
Voltage	220-240 V ~ 50 Hz
Heat Settings	2 (1000 W / 2000 W) + Fan Only
Thermostat	Adjustable
Safety Features	Overheat Protection, Tip-over Switch
Housing Material	Plastic
Color	White / Black
Dimensions (HxWxD)	25 x 20 x 30 cm
Weight	1.5 kg
Cord Length	1.5 m
Noise Level	Approx. 45 dB
Suitable For	Indoor Use
Certifications	CE, GS
Cleaning	Unplug and wipe with dry cloth

Frequently Asked Questions - PS 1002 Niro EINHELL

How do I clean the Einhell PS 1002 Niro heater?

Always unplug the heater before cleaning. Use a dry cloth to wipe the exterior. Do not use water or abrasive cleaners. For the air intake, gently vacuum with a brush attachment.

What safety features does the PS 1002 Niro have?

It includes overheat protection that automatically shuts off the unit if it gets too hot, and a tip-over switch that turns it off if knocked over.

Can I use the heater in a bathroom?

No, this heater is designed for indoor use only in dry areas. It is not splash-proof and should not be used in bathrooms or humid environments.

What is the power consumption of the Einhell PS 1002 Niro?

The heater has a maximum power of 2000 W. It also offers a low setting of 1000 W and a fan-only mode. Actual consumption depends on the setting used.

How do I adjust the thermostat?

Turn the thermostat dial clockwise to increase the desired temperature. The heater will cycle on and off to maintain the set temperature. Turn counterclockwise to lower it.

Does the heater have a fan-only mode?

Yes, setting the power switch to 'Fan' runs the fan without heating, useful for summer air circulation.

What is the noise level of the fan?

The fan operates at approximately 45 dB, which is comparable to a quiet conversation or background music.

Can I leave the heater unattended?

While the heater has safety features, it is recommended to never leave any heater unattended. Always turn it off and unplug when leaving the room.

What is the warranty on the Einhell PS 1002 Niro?

Einhell offers a 2-year warranty from the date of purchase. Keep your receipt and register the product if required.

Are replacement parts available?

Yes, Einhell provides spare parts such as fan blades and thermostats. Check the user manual for part numbers and contact their service center.

USER MANUAL PS 1002 Niro EINHELL

GB Operating Instructions Party Radiator

Read the safety and operating instructions carefully before you use your radiator for the first time. Material and features have been selected to rule out malfunctions provided the radiator is used as intended. Check that all parts are complete.

Contents 1. Description

1. Technical data
2. Assembly
3. Safety instructions
4. Connecting to the gas bottle
5. Operating instructions
6. Cleaning / Maintenance / Repair

1. Description

The party radiator is used outdoors to heat nearby areas.

A burner inside the perforated plate body produces the necessary heat, which is radiated to the immediate surroundings by an aluminium reflector as well as by the perforated plate itself.

The party radiator has to be set up on a level, incombustible surface with no - or only a very slight - gradient. To make it easier to change the gas bottle, the body can be raised and locked in place on the appliance itself. The party radiator is designed to work only with propane-butane (liquefied gas). It is connected directly to the gas bottle by means of a DVGW-tested and approved hose pipe and a liquefied gas regulator (for outlet see nameplate, capacity 1.5 kg/h). The following regulations have to be observed and adhered to when making the connection:

●Technical regulations concerning liquefied gas (e.g. TRF)

● Guidelines published by liability insurance associations concerning the use of liquefied gas in special applications

The burner and all sheet-metal parts and tube parts visible from the outside are made of rust-proof steel. To start the radiator, open the gas bottle, „turn“ the knob to high setting, „press“ the knob (for approx. 10 sec.) and „actuate“ the piezo igniter.

The regulator knob has the settings „zero“, „high“ and „low“. Infinitely variable intermediate settings are possible. A thermoelectric ignition cut-out prevents gas escaping if there is no flame.

The foot, body, connecting pieces and top are made of powder-coated steel for outdoor duty.

The perforated plate body, burner and screws are made of ground high-grade steel.

The reflector shade is made of aluminium.

2. Technical data

Dimensions Total height 2165 mm

Reflector diameter 850 mm

Power rating 12,0 kW

Consumption approx. 0,94 kg/h in high setting

Fuel Propane/butane liquefied gas

Ignition Piezo igniter

Monitoring Thermoelectric flame monitor

Regulator Infinitely adjustable

Gas supply Gas bottles up to 11 kg

3. Assembly

● Before you start to assemble the party radiator, remove the protective plastic coverings.

●Carry out the assembly work on a clean surface where the parts will not be scratched.

●The assembly steps are illustrated on page 6.

● First screw three stems (Item 2) loosely to the base (Item 1) and fit the wheels (Item 11).

- Insert the connecting piece (Item 5) from the side and fasten from underneath. Important: Observe the layout assignment!

- Put on the framework case (Item 3) and fasten loosely with the raised cheesehead screws (layout assignment!).

- Slide the framework lid (Item 4) over the connecting piece and the framework case. Arrange the position of the holes in the framework lid, the framework case and the blind rivet nuts size M5 of the stems so that they coincide and tighten.

●Now tighten all the screws.

- Mount the burner group (Item 6), inserting the hose pipe in the connecting piece (Item 5) as you do so. Be careful not to kink the hose pipe or damage the setting mechanism.

- Now fasten the burner group with the hex screw size M6 x 16 and the washer (12.5. Finally, put on the reflector (Item 7) and screw it in place.

- Insert the gas bottle. Connect the hose pipe to the pressure regulator and the pressure regulator to the

GB

gas bottle - N.B.: 2x left-hand thread. Use leakage spray or a foaming agent to test the joints for leaks.

Never test with a naked flame!

4. Safety instructions

- Set up the party radiator on a level surface with either no or only a very slight gradient (max. 5°).

●Caution: The radiator may be used only under supervision.

●Do not touch the reflector or perforated plate when in use - Risk of burns!

- Keep a safe distance between the radiator and combustible objects during use.

●Do not fasten any objects to the party radiator.

●Use the radiator only outdoors.

●Use the radiator only for heating purposes.

- In strong winds it is advisable to secure the foot with extra weight or to fasten it to the ground or to stand it in a safe place.

- If you are not going to use the party radiator for some time, cover the perforated plate and top with foil in order to prevent dust and insects getting inside.

●Always turn off the party radiator before you move it.

- Check that the seal on the bottle valve is present and in good condition. Do not use additional seals.

- At the first sign of any trouble, close the shut-off valve on the gas bottle at once.

- The party radiator may be operated only in conjunction with a pressure regulator set to the permissible outlet pressure (see the radiator nameplate and factory setting).

- It is imperative to carry out the start-up and ignition procedures as described in section 6.1.

Maintenance: The gas pipe has to be inspected by a specialist workshop every 5 years.

Notes on commercial use:

Various regulations and standards (BGV D34 (VBG 21), DIN 4811-3 and TRF 96) require the installation of a safety pressure regulator with integrated excess pressure cut-out if the party radiator is used commercially (e.g. on fairgrounds). Your party radiator is not supplied with such a safety pressure regulator.

Before you put the radiator into operation it is imperative to use a leak detection spray or a foaming agent to test for leaks at all the connections. Never use a naked flame. Never test for leaks when the radiator is in operation.

5. Connecting to the gas bottle (5 or 11 kg)

To connect the radiator to a gas bottle you need the following parts:

●A standard gas bottle.

- A non-adjustable, DVGW-approved pressure regulator for a maximum capacity of 1.5 kg/h (delivered with the radiator) to match the gas bottle used. Operating pressure as per the factory setting.

● A DVGW-approved hose pipe of sufficient length that can be installed without any kinks.

●A DVGW-approved leak detection spray or a foaming agent.

6. Operating the radiator

6.1 Starting up

Open the gas bottle valve. Turn the button 90° (anti-clockwise) to high setting. Then press the button and at the same time actuate the piezo igniter (a maximum of 5 attempts). Keep the button pressed for approx. 10 seconds after ignition until the burner remains on. If the flame goes out you must wait at least five minutes before making a second attempt at ignition. This is vital to avoid detonations which could put your health at risk

The setting mechanism has the following settings: zero, high (large flame) and low (small flame). Infinitely adjustable setting of the heat output is also possible between these two settings. A thermoelectric ignition cut-out prevents gas escaping when there is no flame.

Ignition

Open the gas bottle valve.

Turn the button 90° anti-clockwise from „closed“ position. Then press the button and ignite the burner by actuating the piezo igniter.

Keep the button pressed for approx. 10 seconds after ignition until the burner remains on.

If the flame goes out you must wait at least two minutes before making a second attempt at ignition.

You can turn the button from the symbol of the small flame (low setting) to the symbol of the large flame (high setting) according to your requirements. Infinitely adjustable setting of the heat output is also possible between these two settings.

Closed High Low

Taking out of operation

To turn off the radiator, move the button to „closed“ position and close the gas bottle valve.

7. Cleaning / Maintenance / Repair

7.1 Cleaning / Maintenance

The party radiator is best cleaned with special stainless steel cleaning agents. A weak alkaline solution can be used for minor cleaning jobs. Under no circumstances are you to use preparations containing salt, sulfur, chlorine or abrasive. Avoid contact with rusting objects - use foil, a piece of carpet or similar to protect the gas bottle and base from such contact.

The party radiator can be cleaned with all standard, non-abrasive and incombustible liquids.

Be sure to turn off the radiator and allow it to cool before commencing with the cleaning.

Caution! Never clean the radiator with pressurized water (using a water hose, steam jet or high pressure)!

7.2 Repair

Have only approved gas fitters carry out repairs and maintenance work on the party radiator.

NL

Three circular diagrams with geometric shapes: a triangle, a trapezoid, and a slanted rectangle, each with a dot at the top (no text or symbols)

The undersigned declares in the name of the company that the product is in compliance with the following guidelines and standards.

⑤ EINHELL GARANTIBEVIS

The guarantee period begins on the sales date and is valid for 2 years.

Responsibility is assumed for faulty construction or material or functional defects.

Any necessary replacement parts an necessary repair work are free of charge.

We do not assume responsibility for consequential damage.

Your customer service partner

© CERTIFICADO DE GARANTIA DA EINHELL

DK EINHELL GARANTIBEVIS

Eschenstraße 6 · D-94405 Landau/Isar (Germany)

Brook House, Brookway

North Chesire Trading Estate

Prenton, Wirral, Chesire

CH 43 3DS

Tel. [phone], Fax [phone]

S.C. A Ap. 9 Sector 1

RO 75 121 Bucharest

Tel. [phone], Fax [phone]

©CZPoker Plus S.R.O.

Areal Vu Bechovice

Budava 10B

CZ-19011 Praha – Bechovice 911

Tel. + Fax: 0042 / 02579 /10204