Q: How to activate and use the automatic opening function of the SIGNATURE SLVI14C42 dishwasher?

The Automatic Opening function allows the door to open automatically after the washing cycle to improve drying. Here’s how to use it: Activating the function Simply press the "Automatic Opening" button on the control panel before starting the washing cycle. Compatible programs This function is only available with the following programs: Auto Intensive Universal ECO Glass 90 min Important: It is not available with the Quick and Soak programs. Precautions to take Do not block the door when this function is activated. An obstacle to the opening could disrupt the automatic locking of the door. Ensure that nothing obstructs the passage after the cycle.

Q: Why does my SIGNATURE MOG25MG microwave beep twice when I press the buttons?

The beeps you hear when pressing the buttons are a normal reaction of the microwave . They are part of the sound confirmation system of the microwave, indicating that your presses have been successfully registered. The manual for your SIGNATURE MOG25MG clearly mentions the following sound signals: A long beep sounds when activating or deactivating the child lock function (by holding the Stop button for 3 seconds in standby mode) Five beeps indicate the end of a defrost cycle For single presses on the buttons, the short beeps you perceive are the normal sound feedback of the microwave - this is its expected behavior. To check: If the beeps seem excessive or unusual, make sure that the child lock function is not accidentally activated. A padlock icon will then appear on the screen. To deactivate it, hold the Stop button for 3 seconds.

Q: Where and how to drill the mounting holes for the wall-mounted hood?

To install the SIGNATURE SHD60FLIGNE hood, you need to drill 5 holes of 8 mm in the wall at the location where you want to install the wall bracket. Important points for installation Installation height: Position the hood at a precise distance above your cooking surface: Minimum 75 cm for a gas stove Minimum 65 cm for electric cooktops Hole diameter: Exactly 8 mm Number of holes: 5 holes in total The manual recommends hiring a qualified electrician for the installation, who will adjust the exact positioning according to your wall configuration and access to the exhaust ducts (diameter 150 mm).

Q: How to use the cooktop?

To use the SIGNATURE STV4F cooktop: 1. Power On Press and hold the power button (M9, symbol ①) for 3 seconds. The device beeps and enters standby mode. 2. Select a Cooking Zone Press the button for the desired zone: M1: Cooking zone #1 M2: Cooking zone #2 M3: Cooking zone #3 M4: Cooking zone #4 3. Adjust Power Use the control buttons: M5 (+): increases power from 0 to 9 M8 (-): decreases power Each press produces a beep to confirm your action. 4. Timer (optional) After setting the power, press M7 (timer selector). The display shows “00”. Use M5 and M8 to set from 1 to 99 minutes. At the end of the countdown, a signal sounds for 2 minutes. 5. Automatic Heating (Boost) For faster heating: Set the power to 9 Press M5 until the display alternates between “R” and “9” Press M8 to choose the final level (e.g., 6) The zone heats up fully for 2.5 minutes, then switches to the chosen level. 6. Power Off Press and hold M9 for 3 seconds to turn off all zones.

Q: What does the error code E6 displayed at the startup of the wine cellar mean?

The error code E6 indicates a communication error from the control system of the wine cellar. What to do immediately: Unplug the device from the electrical outlet Wait a few minutes (at least 5 minutes) Plug the device back in This action resets the system and usually resolves the issue. Remember that you must wait for a 30-minute rest period after initial startup, and a minimum of 5 minutes after each power outage before plugging it back in. If the E6 code reappears after this procedure, it may also indicate a fault with the temperature sensor or the ambient temperature sensor. In this case, contact customer service at 09 78 97 97 97 for diagnosis or intervention.

Q: How to remove and replace the charcoal filter of the SHD60PERI hood?

Before you begin , ensure that the hood is unplugged. Steps to remove the charcoal filter First, remove the metal filters (see diagram 10 in the manual). The charcoal filters are located on both sides of the motor. Turn each charcoal filter counterclockwise until it completely unscrews. Pull the filter towards you to remove it. Important: Replacing the filter The charcoal filter cannot be cleaned and must be replaced approximately every 120 hours of use . To install a new filter, perform the reverse operation: screw it firmly onto the end of the motor until it is tightly secured. You will find an accurate illustration on page 11 (diagram 11) of the PDF manual.

Question 1

How to activate and use the automatic opening function of the SIGNATURE SLVI14C42 dishwasher?

Accepted Answer

The Automatic Opening function allows the door to open automatically after the washing cycle to improve drying. Here’s how to use it:

Activating the function

Simply press the "Automatic Opening" button on the control panel before starting the washing cycle.

Compatible programs

This function is only available with the following programs:

Auto
Intensive
Universal
ECO
Glass
90 min

Important: It is not available with the Quick and Soak programs.

Precautions to take

Do not block the door when this function is activated. An obstacle to the opening could disrupt the automatic locking of the door. Ensure that nothing obstructs the passage after the cycle.

Question 2

How to use the SIGNATURE MOG25MG microwave oven?

Accepted Answer

Using the microwave

The SIGNATURE MOG25MG oven offers several cooking modes. Here’s how to use the main microwave mode:

Press the Microwave button (the display shows P100)
Press Microwave again or turn the knob to choose a power level among: 10%, 30%, 50%, 80%, or 100%
Press Start/+30s to confirm the level
Turn the knob to set the cooking time (up to a maximum of 95 minutes)
Press Start/+30s to start cooking

Other available modes:

Grill: Press Grill/Combi., set the time, then start
Combined cooking: Press Grill/Combi. multiple times to choose C-1 (55% microwave + 45% grill) or C-2 (36% microwave + 64% grill)
Defrosting: By weight - press once on Defrost, set from 100 to 2000g; by duration - press twice, set the time
Automatic menu: 8 preset programs (reheating, meat, vegetables, fish, popcorn, etc.)

Tip: The turntable must always be in place and turn freely. The output power of this device is 900 W for the microwave and 1000 W for the grill.

Question 3

Why does my SIGNATURE MOG25MG microwave beep twice when I press the buttons?

Accepted Answer

The beeps you hear when pressing the buttons are a normal reaction of the microwave. They are part of the sound confirmation system of the microwave, indicating that your presses have been successfully registered.

The manual for your SIGNATURE MOG25MG clearly mentions the following sound signals:

A long beep sounds when activating or deactivating the child lock function (by holding the Stop button for 3 seconds in standby mode)
Five beeps indicate the end of a defrost cycle

For single presses on the buttons, the short beeps you perceive are the normal sound feedback of the microwave - this is its expected behavior.

To check: If the beeps seem excessive or unusual, make sure that the child lock function is not accidentally activated. A padlock icon will then appear on the screen. To deactivate it, hold the Stop button for 3 seconds.

Question 4

How to turn off the SIGNATURE SFMP70 stove?

Accepted Answer

This stove does not have a central on/off button. Here’s how to turn it off:

To stop ongoing cooking

Press the stop button once to pause cooking
Press the stop button twice to completely cancel cooking

To completely turn off the appliance

Set all control knobs to the OFF position
Unplug the appliance from the wall socket for a total shutdown

Energy-saving mode

When the appliance is in standby, press and hold the appropriate button for 3 seconds to turn off the LED screen.

Automatic cooling

After cooking is finished, the cooling fan continues to run for 15 minutes if the internal temperature exceeds 75°C, then it stops automatically.

Question 5

Where and how to drill the mounting holes for the wall-mounted hood?

Accepted Answer

To install the SIGNATURE SHD60FLIGNE hood, you need to drill 5 holes of 8 mm in the wall at the location where you want to install the wall bracket.

Important points for installation

Installation height: Position the hood at a precise distance above your cooking surface:
- Minimum 75 cm for a gas stove
- Minimum 65 cm for electric cooktops
Hole diameter: Exactly 8 mm
Number of holes: 5 holes in total

The manual recommends hiring a qualified electrician for the installation, who will adjust the exact positioning according to your wall configuration and access to the exhaust ducts (diameter 150 mm).

Question 6

How to use the cooktop?

Accepted Answer

To use the SIGNATURE STV4F cooktop:

1. Power On

Press and hold the power button (M9, symbol ①) for 3 seconds. The device beeps and enters standby mode.

2. Select a Cooking Zone

Press the button for the desired zone:

M1: Cooking zone #1
M2: Cooking zone #2
M3: Cooking zone #3
M4: Cooking zone #4

3. Adjust Power

Use the control buttons:

M5 (+): increases power from 0 to 9
M8 (-): decreases power

Each press produces a beep to confirm your action.

4. Timer (optional)

After setting the power, press M7 (timer selector). The display shows “00”. Use M5 and M8 to set from 1 to 99 minutes. At the end of the countdown, a signal sounds for 2 minutes.

5. Automatic Heating (Boost)

For faster heating:

Set the power to 9
Press M5 until the display alternates between “R” and “9”
Press M8 to choose the final level (e.g., 6)

The zone heats up fully for 2.5 minutes, then switches to the chosen level.

6. Power Off

Press and hold M9 for 3 seconds to turn off all zones.

Question 7

What does the error code E6 displayed at the startup of the wine cellar mean?

Accepted Answer

The error code E6 indicates a communication error from the control system of the wine cellar.

What to do immediately:

Unplug the device from the electrical outlet
Wait a few minutes (at least 5 minutes)
Plug the device back in

This action resets the system and usually resolves the issue. Remember that you must wait for a 30-minute rest period after initial startup, and a minimum of 5 minutes after each power outage before plugging it back in.

If the E6 code reappears after this procedure, it may also indicate a fault with the temperature sensor or the ambient temperature sensor. In this case, contact customer service at 09 78 97 97 97 for diagnosis or intervention.

Question 8

How to remove and replace the charcoal filter of the SHD60PERI hood?

Accepted Answer

Before you begin, ensure that the hood is unplugged.

Steps to remove the charcoal filter

First, remove the metal filters (see diagram 10 in the manual).
The charcoal filters are located on both sides of the motor.
Turn each charcoal filter counterclockwise until it completely unscrews.
Pull the filter towards you to remove it.

Important: Replacing the filter

The charcoal filter cannot be cleaned and must be replaced approximately every 120 hours of use. To install a new filter, perform the reverse operation: screw it firmly onto the end of the motor until it is tightly secured.

You will find an accurate illustration on page 11 (diagram 11) of the PDF manual.

Question 9

Does the SHD60PERI hood have a reset button?

Accepted Answer

No, the SIGNATURE SHD60PERI hood does not have a physical reset button. According to the user manual, this hood has only four buttons:

The Power button: to turn the device on and off
The Speed button: to adjust the airflow (3 speeds: low, medium, high)
The Light button: to control the built-in LED lighting
The Timer button: to program an automatic shut-off after 9 minutes

The SHD60PERI hood includes a thermal safety device that automatically shuts off the device if it detects overheating. If your hood stops during operation, it is usually due to this device. To restart the device, turn off the hood with the Power button and wait a few minutes before turning it back on, allowing the safety device to reset.

If you want to completely reset the hood's functions in case of malfunction, you can perform an electrical reset: unplug the hood from the wall outlet for about 10 seconds, then plug it back in. This action will restore the device's settings and should resolve minor operational issues.

If the problem persists or if the hood does not restart properly, check that the grease filter is not clogged (the filters can be cleaned in hot water with detergent) and that the hood is well-ventilated. As a last resort, contact SIGNATURE customer service.

Question 10

Why won't my SHD60PERI hood turn on?

Accepted Answer

If your SIGNATURE SHD60PERI hood won't turn on, start by checking the following points:

Check the electrical connection: Make sure the hood is properly plugged in and that the electrical circuit is functioning. Test with another device on the same outlet.
Press the Power button: Your hood is equipped with a Power button designed to start/stop the unit. Ensure you are activating it correctly.
Check the Speed button: The Speed button allows you to adjust the speed (low, medium, high). According to the manual, if no speed is selected, the unit will not operate. Try changing the setting.
Let it cool down: If your hood has stopped unexpectedly, the thermal safety system may have been activated. Wait a few minutes before restarting.

If after these checks the hood remains inoperative, it is likely that an internal component is faulty and professional repair will be necessary.

User manual SIGNATURE : user manuals and guides in PDF

Models SIGNATURE most viewed

Browse manuals SIGNATURE by appliance type

Recent questions about devices SIGNATURE