Q: When starting the piano, all the indicators light up and the controls are locked - is this normal?

This is a completely normal behavior. Here’s what happens: When turning on the TT 6234 All indicator lights and dashboard lights briefly illuminate and a short beep sounds This corresponds to a normal startup test of the device The controls are automatically locked for safety to prevent accidental changes How to unlock the controls Press the lock button for a few moments. The lock indicator will turn off and you will be able to use the controls normally, retaining the previous settings. Important note If the lights do not turn off after a few seconds, or if the piano does not respond after unlocking, check that no object is obstructing the controls or the control panel.

Q: Why does the dishwasher stop with a beep and not complete the washing cycle?

A stop of the cycle accompanied by a beep is generally an emergency stop alarm . Your manual indicates two possible error codes: Code 6 - Water supply alert The ON/OFF light is flashing and the screen displays the number 6 . Cause: Water tap closed or supply hose bent Solution: Open the main water tap Check that the supply hose is not bent Wait 20 seconds Press ON/OFF and restart a program Code 7 - Clogged water supply filter The ON/OFF light is flashing and the screen displays the number 7 . Cause: The water supply filter is blocked Solution: Close the water tap immediately Unplug the appliance Clean the water supply filter Reassemble everything and restart If no error code is displayed, also check: That the door closes completely with a click That the drain hose is not bent That the sink drain is not clogged

Q: Which "-" button should I use to adjust the temperature and which "-" button for the time?

The SCHOLTES FP T5.1 N S oven has a single "-" button that controls both the temperature and the time , depending on the operating context. To adjust the temperature: during cooking, press the "-" button to decrease the temperature (range: 30°C to 250°C, 300°C in barbecue mode). You can also use the "+" button to increase it. The temperature is displayed on the TEMPERATURA display . To set the cooking duration: before starting, press the specific button for programming the duration (timer symbol), then use the "+" and "-" buttons to select the desired time. The duration is displayed on the TEMPI display . Automatic memory: each setting you make is automatically saved after 10 seconds without action. Scrolling acceleration: to scroll through values more quickly on the screen, press and hold the "+" and "-" buttons simultaneously.

Q: What happens when you press the START and minus keys simultaneously on this oven?

When you press the START and minus (-) keys simultaneously for about 3 seconds , you deactivate the DEMO mode (demonstration mode) of the SCHOLTES FP T5.1 N S oven. This action causes the message "dEof" to appear on the TEMPERATURE display and emits a sound signal. The DEMO mode is a mode of operation where all heating elements are disabled but the controls remain operational. It is intended for demonstration and display purposes. When this mode is active, the oven does not actually heat but you can test all the buttons and programs. If you have accidentally activated the DEMO mode of your oven, this key combination allows you to quickly deactivate it to return to normal operation. Once you have pressed START and minus simultaneously for 3 seconds and the message "dEof" appears, the DEMO mode is deactivated and your oven returns to its standard operating mode. Conversely, to activate the DEMO mode, the procedure is different: you need to press the first manual cooking key (top left), then press the plus and minus keys together for 6 seconds, before briefly pressing the start key.

Q: What does the error code ER07 mean and how can it be fixed?

The ER07 code means that the oven has detected an overheating in the cavity . This usually occurs during a pyrolysis cycle (at 500°C) or after prolonged heavy use. What to do Let the oven cool completely (30 to 60 minutes) and then turn it back on. If it was a temporary overheating, the error will disappear. Check the ventilation grilles around the oven. A blockage reduces air circulation and can trigger this code. Clean them if necessary. If the error consistently returns after cooling and cleaning, it indicates that the temperature probe (NTC sensor) is likely defective or that the electronic board has a problem . Important: The manual for this model does not detail parts replacement. In case of persistent error, contact SCHOLTES customer service at 0825 33 66 66 (number provided in your manual). A technician will be able to diagnose whether the probe or the electronic board needs to be replaced.

Question 1

When starting the piano, all the indicators light up and the controls are locked - is this normal?

Accepted Answer

This is a completely normal behavior. Here’s what happens:

When turning on the TT 6234

All indicator lights and dashboard lights briefly illuminate and a short beep sounds
This corresponds to a normal startup test of the device
The controls are automatically locked for safety to prevent accidental changes

How to unlock the controls

Press the lock button for a few moments. The lock indicator will turn off and you will be able to use the controls normally, retaining the previous settings.

Important note

If the lights do not turn off after a few seconds, or if the piano does not respond after unlocking, check that no object is obstructing the controls or the control panel.

Question 2

My cooking hob turns off after 4 minutes - how can I solve this problem?

Accepted Answer

If your SCHOLTES MULTIPLO.1 SF hob turns off after 4 minutes, it is likely due to the appliance's automatic safety shut-off system. According to the specifications of this hob, the maximum usage time varies depending on the power level selected: from 10 hours at level 1 to 1 hour at maximum power.

Checks to perform

Check the selected power level - If you are cooking at high power, the appliance automatically shuts off after a maximum of 1 hour. Lower the power level for extended cooking.
Check utensil detection - The hob has automatic detection for compatible utensils. Ensure that your pot or pan is properly detected at startup. If no compatible utensil is recognized, the appliance cuts off the power.
Check the residual heat indicator - Wait for the

Question 3

Why does the dishwasher stop with a beep and not complete the washing cycle?

Accepted Answer

A stop of the cycle accompanied by a beep is generally an emergency stop alarm. Your manual indicates two possible error codes:

Code 6 - Water supply alert

The ON/OFF light is flashing and the screen displays the number 6.

Cause: Water tap closed or supply hose bent
Solution:
1. Open the main water tap
2. Check that the supply hose is not bent
3. Wait 20 seconds
4. Press ON/OFF and restart a program

Code 7 - Clogged water supply filter

The ON/OFF light is flashing and the screen displays the number 7.

Cause: The water supply filter is blocked
Solution:
1. Close the water tap immediately
2. Unplug the appliance
3. Clean the water supply filter
4. Reassemble everything and restart

If no error code is displayed, also check:

That the door closes completely with a click
That the drain hose is not bent
That the sink drain is not clogged

Question 4

What should I do if the OK button on the SCHOLTES FLR 934 XA oven is not working?

Accepted Answer

The OK button is a central control of the SCHOLTES FLR 934 XA oven used to confirm selections in the menus and validate temperature and duration settings.

If this button is unresponsive, here are the steps to check:

Check the power to the control panel: First, press the ⏻ (power on) button to ensure that the control panel is activated. If the panel remains inactive, all buttons, including OK, will not function.
Test the other buttons: Try the directional arrows (up/down) or the START/STOP button to see if other controls respond. If no buttons respond, it is a power or general electronic issue.
Check the cleanliness of the button: The contact may be dirty. Gently clean around the OK button with a damp cloth (without excess water) and try again.
Restart the oven: Completely turn off the oven (cut the power for a few minutes), then turn it back on and test the OK button.

If after these checks the OK button remains inactive and the other controls work, it is likely a failure of the button itself or its electronic circuit, requiring technical intervention.

Question 5

What does error code 12 mean on the SCHOLTES FLR 934 XA oven?

Accepted Answer

The PDF of this manual does not specifically detail error code 12 for the SCHOLTES FLR 934 XA. However, here’s what you can do:

What you can do immediately

Perform a reset: Some temporary error codes disappear after a reset. Wait 30 seconds after turning off the oven, then turn it back on.
Check the exact message: Make sure that the displayed message is indeed "12" and not another combination.

Technical support

To obtain the exact meaning of error code 12 and specific solutions for this model, contact Scholtes technical support listed in the manual (see the Support section of the manual).

It is important to note that on this type of device, error codes are generally related to sensor (temperature, humidity) or electrical component failures, but only the manufacturer can confirm the exact diagnosis for your model.

Question 6

How to clean and maintain the SCHOLTES FN 36 XA oven?

Accepted Answer

Regular cleaning of your SCHOLTES FN 36 XA oven maintains its performance. Here’s how to proceed according to the manual:

Before you start

Turn off the power supply before any cleaning.

Cleaning the interior

Clean the oven while it is still warm after use. Use hot water and a mild detergent, then dry with a soft cloth. Never use abrasive products that could damage the wall.

Exterior, seals, and door

Exterior and seals: Wipe with a sponge soaked in warm water with neutral detergent, rinse thoroughly, and dry. Avoid abrasive powders and corrosive products.
Door glass: Use a non-abrasive sponge and a soft cloth. Never scrape with a metal scraper or abrasive object that could scratch the glass.
Seal inspection: Regularly check the condition of the seal around the door. If it is damaged, contact customer service and do not use the oven until it is repaired.

Accessories

The accessories (grids, drip tray) can be washed like regular dishes, dishwasher compatible.

PYROLYSIS function - automatic cleaning

This cycle reaches 500°C to carbonize dirt. Before activating it:

Remove all accessories from the oven
Wipe off excess residues with a damp sponge
Close the door

Three levels are available: Economic (1h), Normal (1h30), or Intensive (2h). Once the cycle is complete and the oven has cooled, harmless white powdery residues can be easily wiped away with a damp sponge.

What NOT to do

Never use a steam cleaner or high-pressure washer
No abrasive or corrosive products
No metal scraper on the glass

For a deep clean of the door, it is removable: open it fully, lift the hinge levers, partially close it, press on the stops, then pull towards you.

Question 7

Which "-" button should I use to adjust the temperature and which "-" button for the time?

Accepted Answer

The SCHOLTES FP T5.1 N S oven has a single "-" button that controls both the temperature and the time, depending on the operating context.

To adjust the temperature: during cooking, press the "-" button to decrease the temperature (range: 30°C to 250°C, 300°C in barbecue mode). You can also use the "+" button to increase it. The temperature is displayed on the TEMPERATURA display.
To set the cooking duration: before starting, press the specific button for programming the duration (timer symbol), then use the "+" and "-" buttons to select the desired time. The duration is displayed on the TEMPI display.
Automatic memory: each setting you make is automatically saved after 10 seconds without action.
Scrolling acceleration: to scroll through values more quickly on the screen, press and hold the "+" and "-" buttons simultaneously.

Question 8

What happens when you press the START and minus keys simultaneously on this oven?

Accepted Answer

When you press the START and minus (-) keys simultaneously for about 3 seconds, you deactivate the DEMO mode (demonstration mode) of the SCHOLTES FP T5.1 N S oven. This action causes the message "dEof" to appear on the TEMPERATURE display and emits a sound signal.

The DEMO mode is a mode of operation where all heating elements are disabled but the controls remain operational. It is intended for demonstration and display purposes. When this mode is active, the oven does not actually heat but you can test all the buttons and programs.

If you have accidentally activated the DEMO mode of your oven, this key combination allows you to quickly deactivate it to return to normal operation. Once you have pressed START and minus simultaneously for 3 seconds and the message "dEof" appears, the DEMO mode is deactivated and your oven returns to its standard operating mode.

Conversely, to activate the DEMO mode, the procedure is different: you need to press the first manual cooking key (top left), then press the plus and minus keys together for 6 seconds, before briefly pressing the start key.

Question 9

My SCHOLTES FP T5.1 N S oven only displays 'Demo' and 'on' instead of the time and temperature, why is it not heating?

Accepted Answer

This is a very simple problem to solve - the demo mode of your oven is activated. In demo mode, the screen displays "Demo" instead of the time and "on" instead of the temperature. The oven does not actually heat and turns off by itself for safety, which is normal in demo mode.

To deactivate demo mode on your SCHOLTES FP T5.1 N S oven:

Oven completely off
Press and hold the START button and the "-" button simultaneously for 3 seconds
A beep will sound and the screen will display "dEof" - this confirms that demo mode is deactivated

Once this procedure is completed, your oven will operate normally and heat properly.

Question 10

What does the error code ER07 mean and how can it be fixed?

Accepted Answer

The ER07 code means that the oven has detected an overheating in the cavity. This usually occurs during a pyrolysis cycle (at 500°C) or after prolonged heavy use.

What to do

Let the oven cool completely (30 to 60 minutes) and then turn it back on. If it was a temporary overheating, the error will disappear.
Check the ventilation grilles around the oven. A blockage reduces air circulation and can trigger this code. Clean them if necessary.
If the error consistently returns after cooling and cleaning, it indicates that the temperature probe (NTC sensor) is likely defective or that the electronic board has a problem.

Important: The manual for this model does not detail parts replacement. In case of persistent error, contact SCHOLTES customer service at 0825 33 66 66 (number provided in your manual). A technician will be able to diagnose whether the probe or the electronic board needs to be replaced.

User manual SCHOLTES : user manuals and guides in PDF

Models SCHOLTES most viewed

Browse manuals SCHOLTES by appliance type

Recent questions about devices SCHOLTES