Q: What type and how much oil should be used for the MURRAY MX550 mower?

Type of oil: The MURRAY MX550 mower is equipped with a 4-stroke engine that requires: SAE 30 for temperatures above 0 °C 10W-30 for lower temperatures Quantity of oil: The MX550 manual does not specify the exact capacity in milliliters. However, it is essential that before each start, you check that the engine has a sufficient amount of oil. The manual emphasizes: never start the engine without having filled it with oil. Filling and maintenance: Make sure to check the oil level regularly. Drain the engine oil when it is warm and replace it with new oil as needed based on your usage. Keep all engine fasteners tight. Additional lubrication: Beyond the engine, also lubricate the wheels and all pivots of the mower with engine oil every 25 hours of operation to ensure proper maintenance of your device.

Q: What is the cutting width of the MURRAY MXH675 mower?

The MURRAY MXH675 mower has a cutting width of 50 cm . This dimension corresponds to the total width of the deck (the chassis) that contains the rotating cutting blade. The 50 cm cutting width allows you to mow your lawn efficiently with a minimal number of passes. This width complies with the standards of professional walk-behind mowers in this range. The cutting is ensured by a single rotating blade mounted under the deck that lifts and cuts the grass. For optimal results, keep the blade well sharpened (replace it approximately every 2 years) and regularly check that the blade is in good condition and properly balanced before each use. The cutting height is individually adjustable by wheel with positions from 2.5 cm to 10 cm of effective height. For a well-mowed lawn, set the cutting height to cut only the top third of the grass and ensure that each wheel is at the same height to achieve an even and consistent cut.

Q: Where is the cutting height lever located on the MURRAY MX550 mower and how do I use it?

Location of the lever: The cutting height lever of the MURRAY MX550 mower is located on the side of the machine , easily accessible when you are in mowing position. It is usually identifiable by markers or symbols indicating different cutting heights. Depending on your MX550 model, you will have either individual levers for each wheel (called adjustment arms) or a single adjustment lever that controls the overall cutting height. How to use it: Before any adjustments, completely stop the engine and disconnect the spark plug wire for safety reasons. If your model has individual levers for each wheel, move the adjustment arm of each wheel to the desired position, ensuring that all arms are at the same height to ensure an even cut. If your MX550 has a single adjustment lever, simply move this lever to the position corresponding to the desired cutting height. Unlock the lever if necessary before repositioning it. Recommended cutting heights: The maximum effective cutting height is 9.8 cm . For optimal results, set the lever to cut only the top third of the grass . If your lawn exceeds 10 cm in height, two passes are necessary: first set the lever to the maximum position, then lower it for the second pass. The grass to be mowed should not exceed 15 cm in length. Usage tips: After each adjustment of the lever, visually check that the blade is positioned at the desired height. Keep your cutting blade well sharpened to prevent the tips of the grass from turning brown. Regularly clean the underside of the mower deck, as the accumulation of grass and debris can affect the quality of the cut and the performance of the machine.

Question 1

Where can I buy a replacement blade for the MURRAY MX550 mower?

Accepted Answer

To purchase a replacement blade for your MURRAY MX550 mower, you have several effective options depending on your urgency and preference. The manufacturer's manual recommends using only original parts approved by MURRAY for safety and performance reasons.

Authorized dealers and specialty stores - Contact an Authorized MURRAY Repairer in your area: they have original blades and can advise you on the exact model you need. These professionals can also sharpen or replace the blade directly on your mower if you wish. To find a dealer, check the official MURRAY website or call with your model number (MX550) and your serial number.

Gardening and agricultural stores - Stores specializing in gardening equipment offer blades for riding mowers and can order one if it's not in stock. This is often the quickest option if you need it in the coming days.

Specialized online shops - Several online retailers offer blades suitable for the MURRAY MX550, including mulching blades. Search for "MURRAY MX550 blade" or "MURRAY mower blade 46 cm" (your mower has a cutting width of approximately 46 cm). Make sure the blade is compatible with your exact model before ordering.

Information to have before ordering - To order correctly, prepare: your model number (MX550), your serial number (visible on the mower's chassis), the part number if available, and the quantity. This information ensures that you receive the correct blade for your machine.

Direct contact with the manufacturer - If you cannot find the part locally, you can contact Briggs & Stratton UK Ltd (the manufacturer of the MURRAY engine): Road Four, Winsford Industrial Estate, Winsford, Cheshire CW7 3QN, United Kingdom. They can direct you to a distributor or authorized dealer.

Important for safety - The manual recommends replacing the blade every two years of use to maintain optimal cutting and ensure your safety. Before any intervention on the blade, stop the engine, disconnect the spark plug wire, and let the machine cool down. If you are not comfortable replacing the blade yourself, an Authorized Repairer can perform this operation quickly and safely.

Question 2

What type and how much oil should be used for the MURRAY MX550 mower?

Accepted Answer

Type of oil: The MURRAY MX550 mower is equipped with a 4-stroke engine that requires:

SAE 30 for temperatures above 0 °C
10W-30 for lower temperatures

Quantity of oil: The MX550 manual does not specify the exact capacity in milliliters. However, it is essential that before each start, you check that the engine has a sufficient amount of oil. The manual emphasizes: never start the engine without having filled it with oil.

Filling and maintenance: Make sure to check the oil level regularly. Drain the engine oil when it is warm and replace it with new oil as needed based on your usage. Keep all engine fasteners tight.

Additional lubrication: Beyond the engine, also lubricate the wheels and all pivots of the mower with engine oil every 25 hours of operation to ensure proper maintenance of your device.

Question 3

What is the cutting width of the MURRAY MXH675 mower?

Accepted Answer

The MURRAY MXH675 mower has a cutting width of 50 cm. This dimension corresponds to the total width of the deck (the chassis) that contains the rotating cutting blade.

The 50 cm cutting width allows you to mow your lawn efficiently with a minimal number of passes. This width complies with the standards of professional walk-behind mowers in this range.

The cutting is ensured by a single rotating blade mounted under the deck that lifts and cuts the grass. For optimal results, keep the blade well sharpened (replace it approximately every 2 years) and regularly check that the blade is in good condition and properly balanced before each use.

The cutting height is individually adjustable by wheel with positions from 2.5 cm to 10 cm of effective height. For a well-mowed lawn, set the cutting height to cut only the top third of the grass and ensure that each wheel is at the same height to achieve an even and consistent cut.

Question 4

How do I remove the blade from the Murray EC370 lawn mower?

Accepted Answer

To remove the blade from your Murray EC370 lawn mower, follow these precise steps:

Required materials:

A wrench or an appropriate spanner for the blade nut
A cloth or protective glove
A block to prevent the blade from turning (e.g., a wooden wedge)

Disassembly steps:

Disconnect the mower or remove the spark plug if it is a gas mower, to prevent any accidental starting.
Place the mower on its side ensuring that fuel does not spill (nozzle facing up if gas engine).
Block the blade using a wooden wedge or a specific tool to prevent it from turning while loosening.
Use the wrench to loosen the nut that holds the blade. Generally, you need to turn it counterclockwise.
Carefully remove the nut and the blade. Note the position of the blade for reassembly.
Inspect the blade to check its condition or to proceed with its replacement.

Safety tips: Always wear gloves to protect your hands and ensure that the mower is securely immobilized before starting.

Question 5

Where is the spark plug located on the Murray 1695886 snow blower?

Accepted Answer

The spark plug of the Murray 1695886 snow blower is located directly on the engine. To locate it:

Remove the engine protective cover (often referred to as the engine shroud or blower cover).
Once this cover is removed, you will see a spark plug wire connected to the spark plug itself.

The spark plug is generally accessible by following this wire, which is often identified by a letter or specific marking in the technical documentation.

It is recommended to check the condition of the spark plug regularly and replace it if necessary to ensure good starting and optimal operation of the blower.

Question 6

Where is the air filter located on the Murray snow blower model 1695886?

Accepted Answer

On the Murray snow blower model 1695886, the air filter is an optional component that is only present on certain configurations. If your device is equipped with one, here’s how to locate and access it.

Location of the air filter: The air filter is generally located near the engine, in a housing or a cleaning assembly situated above or near the carburetor. It is usually protected by a plastic or metal cover that you can remove by unlocking it or unscrewing the fastening screws. To access the filter, first turn off the engine, wait for it to cool down, and then inspect the top and sides of the engine block.

Check before accessing the filter: Refer to your specific user manual or the parts diagram available at www.murray.com to precisely identify if your model 1695886 has an air filter. The model and serial number of your device will allow you to obtain the exact documentation.

Filter maintenance: If your snow blower is equipped with a filter, regular maintenance is important for the proper functioning of the engine. Depending on the technical specifications of the model, cleaning the air filter is part of the recommended maintenance. Never operate the engine with the air filter removed or the cleaning housing open, as this could damage the engine.

For maintenance or replacement of the filter, consult an authorized Murray dealer who will have the complete documentation and compatible spare parts for your model 1695886.

Question 7

Where is the cutting height lever located on the MURRAY MX550 mower and how do I use it?

Accepted Answer

Location of the lever: The cutting height lever of the MURRAY MX550 mower is located on the side of the machine, easily accessible when you are in mowing position. It is usually identifiable by markers or symbols indicating different cutting heights. Depending on your MX550 model, you will have either individual levers for each wheel (called adjustment arms) or a single adjustment lever that controls the overall cutting height.

How to use it: Before any adjustments, completely stop the engine and disconnect the spark plug wire for safety reasons. If your model has individual levers for each wheel, move the adjustment arm of each wheel to the desired position, ensuring that all arms are at the same height to ensure an even cut. If your MX550 has a single adjustment lever, simply move this lever to the position corresponding to the desired cutting height. Unlock the lever if necessary before repositioning it.

Recommended cutting heights: The maximum effective cutting height is 9.8 cm. For optimal results, set the lever to cut only the top third of the grass. If your lawn exceeds 10 cm in height, two passes are necessary: first set the lever to the maximum position, then lower it for the second pass. The grass to be mowed should not exceed 15 cm in length.

Usage tips: After each adjustment of the lever, visually check that the blade is positioned at the desired height. Keep your cutting blade well sharpened to prevent the tips of the grass from turning brown. Regularly clean the underside of the mower deck, as the accumulation of grass and debris can affect the quality of the cut and the performance of the machine.

User manual MURRAY : user manuals and guides in PDF

Models MURRAY most viewed

Browse manuals MURRAY by appliance type

Recent questions about devices MURRAY