Q: What are the error codes and diagnostic codes for the ASUS H81-GAMER motherboard?

The ASUS H81-GAMER motherboard features a status LED diagnostic system and beep codes to identify issues during startup (POST - Power-On Self-Test). Diagnostic LEDs Most ASUS H81 motherboards have diagnostic LEDs located near the CPU connector. They indicate the status of key components: CPU LED - lights up if the processor is not detected or improperly inserted DRAM LED - lights up if the RAM is not installed or is faulty VGA LED - lights up if the graphics card is not installed or is improperly connected BOOT LED - lights up in case of a boot error If a LED remains lit after startup, it indicates a problem with the corresponding component. Beep Codes If the system emits a series of beeps, here are the common codes: 1 beep - Normal startup (no issues) 1 long beep + 2 short beeps - RAM error Continuous beeping - RAM or CPU failure 1 long beep + 1 short beep - VGA error For more details on specific error codes for your configuration, refer to the diagnostic or troubleshooting section of the installation manual provided with your motherboard.

Q: What are the best settings for the ASUS TUF Gaming VG27VQ3B monitor?

To optimize your ASUS TUF Gaming VG27VQ3B , here are the recommended settings based on your usage: For competitive gaming: Refresh rate: 240 Hz (native to the monitor) Response time: Ultra Fast or Fast (depending on the game) Synchronization: Enable G-Sync (if NVIDIA GPU) or FreeSync (if AMD GPU) Brightness: 80-100% for intensive gaming, 50-70% if playing in a dark room Contrast: 50-60% (the default value generally works well) Color mode: Prioritize gaming dedicated modes (check the OSD menu) For work/office use: Brightness: 40-60% to reduce eye strain Response time: Normal or Standard Synchronization: Can remain enabled, disable if artifacts occur Tip: Access all settings via the monitor's OSD menu (side buttons). For finer calibration based on your equipment, refer to the complete PDF manual of this notice.

Q: Where is the volume button on the ASUS VivoTab RT TF600T?

The volume button on your ASUS VivoTab RT TF600T is located on the back of the tablet . According to the diagram shown in the manual, it is labeled as #2 in the rear view. You can refer to the precise identification diagram on the first page of the manual to locate this button exactly. It allows you to increase or decrease the volume of your device.

Q: My ROG Kunai 3 shows 'not connected' on my ASUS phone - how to reconnect the controller?

If your ROG Kunai 3 shows 'not connected' in the hardware info of your ASUS ROG Phone, here’s how to reconnect it: If the controller was already paired before Simply press the home button on the controller. It should automatically reconnect to the last paired phone. Make sure that your phone's Bluetooth is turned on . If the controller does not reconnect Check the battery level via the LED indicator (solid red = very low battery 0-25%) If the battery is very low, connect the controller via USB Type-C to charge it (solid white = charging) Try restarting the controller: hold the home button for 10 seconds , then press it again to turn it on Complete Bluetooth re-pairing If the above steps do not work, re-pair the controller: Set the connection switch to Bluetooth (side of the controller) Press the home button to turn on the controller - the LED indicator blinks slowly in blue Hold the home button for 3 to 5 seconds until the indicator blinks quickly in blue (pairing mode active) On your phone, go to Settings > Bluetooth Select 'ROG Kunai 3 Gamepad' from the list of available devices The controller is now reconnected. The LED indicator will turn green (battery 90-100%) or yellow (battery 25-90%) depending on the charge level.

Q: Is the ZenWiFi AX Hybrid XP4 compatible with devolo 1200+ powerline adapters?

The ZenWiFi AX Hybrid XP4 is equipped with a Powerline Backhaul function using the HomePlug AV1300 standard , allowing it to create an upstream link via your home's electrical network to connect the mesh system nodes together. However, compatibility with the Devolo 1200+ is not guaranteed . Devolo 1200+ adapters generally use the HomePlug AV standard (an earlier version), while the XP4 operates on AV1300. Although these two standards are technically backward compatible, they rarely work together at optimal speeds on the same electrical network. Potential issues : If you connect the Devolo 1200+ and the XP4 on the same electrical circuit, they may recognize each other but with degraded performance . The speed will be limited to the older version of the protocol (HomePlug AV), which can significantly reduce transfer speeds and cause connection instability. Additionally, the XP4 is designed to operate in a coherent system with other ASUS devices using AV1300. Recommendation : To avoid conflicts and performance issues, do not use the Devolo 1200+ simultaneously with the ZenWiFi XP4 system. If you already have the Devolo, it is advisable to prioritize the ASUS XP4 mesh system with PowerLine Backhaul rather than mixing the two brands. If you absolutely need to extend your network, prefer a wired Ethernet connection (Ethernet Backhaul) or WiFi 6 (WiFi Backhaul) between the XP4 nodes. To optimize Powerline on XP4 : Always connect cables directly to a wall outlet (no extensions), use grounded outlets (3 prongs), and avoid plugging into the same circuit as high-energy-consuming devices (radiator, washing machine, air conditioner).

Question 1

Do I need to press the power button of the ASUS ZenPower 10050C multiple times?

Accepted Answer

No, the power button of the ZenPower 10050C should only be pressed once for each function:

Short press (less than one second): displays the charge status via the indicator LEDs (3 LEDs = 61-100%, 2 LEDs = 31-60%, 1 LED = 5-30%, blinking = less than 5%). The indicators turn off automatically after 5 seconds.
Long press of 3-5 seconds: activates or deactivates the built-in LED flashlight.

Important point: This battery does not have a power switch. It activates automatically as soon as you connect a device to charge - you do not need to press the button to start charging.

If the button does not respond to a simple press, check that:

The battery has a charge (test by connecting your phone)
The button is not physically stuck
You are pressing the button firmly

Question 2

What are the error codes and diagnostic codes for the ASUS H81-GAMER motherboard?

Accepted Answer

The ASUS H81-GAMER motherboard features a status LED diagnostic system and beep codes to identify issues during startup (POST - Power-On Self-Test).

Diagnostic LEDs

Most ASUS H81 motherboards have diagnostic LEDs located near the CPU connector. They indicate the status of key components:

CPU LED - lights up if the processor is not detected or improperly inserted
DRAM LED - lights up if the RAM is not installed or is faulty
VGA LED - lights up if the graphics card is not installed or is improperly connected
BOOT LED - lights up in case of a boot error

If a LED remains lit after startup, it indicates a problem with the corresponding component.

Beep Codes

If the system emits a series of beeps, here are the common codes:

1 beep - Normal startup (no issues)
1 long beep + 2 short beeps - RAM error
Continuous beeping - RAM or CPU failure
1 long beep + 1 short beep - VGA error

For more details on specific error codes for your configuration, refer to the diagnostic or troubleshooting section of the installation manual provided with your motherboard.

Question 3

What are the best settings for the ASUS TUF Gaming VG27VQ3B monitor?

Accepted Answer

To optimize your ASUS TUF Gaming VG27VQ3B, here are the recommended settings based on your usage:

For competitive gaming:

Refresh rate: 240 Hz (native to the monitor)
Response time: Ultra Fast or Fast (depending on the game)
Synchronization: Enable G-Sync (if NVIDIA GPU) or FreeSync (if AMD GPU)
Brightness: 80-100% for intensive gaming, 50-70% if playing in a dark room
Contrast: 50-60% (the default value generally works well)
Color mode: Prioritize gaming dedicated modes (check the OSD menu)

For work/office use:

Brightness: 40-60% to reduce eye strain
Response time: Normal or Standard
Synchronization: Can remain enabled, disable if artifacts occur

Tip: Access all settings via the monitor's OSD menu (side buttons). For finer calibration based on your equipment, refer to the complete PDF manual of this notice.

Question 4

Is the USB-C connection powerful enough to operate the Blu-ray player?

Accepted Answer

Yes, the USB-C connection is sufficient for the ASUS SBW06D5HU Blu-ray player, provided that the correct configuration is followed.

This player does not require an external power adapter - it draws all its power via USB. However, for reading and writing Blu-ray, you must use the Y-cable provided that connects TWO USB ports simultaneously to your computer or USB hub.

Why two USB connections are necessary

A single USB port may be sufficient for reading or writing DVDs and CDs (speeds up to 8x and 24x respectively)
Reading and writing Blu-ray (up to 6x) requires higher power delivery, hence the dual connection to ensure stable power supply

Make sure that your computer or USB hub has two available ports and that you properly connect both connectors of the Y-cable. This is the only requirement for the player to function correctly with Blu-ray discs.

Question 5

Where is the volume button on the ASUS VivoTab RT TF600T?

Accepted Answer

The volume button on your ASUS VivoTab RT TF600T is located on the back of the tablet. According to the diagram shown in the manual, it is labeled as #2 in the rear view.

You can refer to the precise identification diagram on the first page of the manual to locate this button exactly. It allows you to increase or decrease the volume of your device.

Question 6

How many internal storage ports (M.2 or SATA) does this laptop have?

Accepted Answer

The notice available on this page does not specify the exact number of internal storage ports (M.2 or SATA) for the K501UX model. However, according to the technical specifications of the K501UX, this laptop is equipped with a 512 GB SSD storage slot (standard configuration).

Generally, ASUS laptops of this range and generation (K501 series, 2016) have a single M.2 NVMe port for primary storage, and some models offer the possibility to add a second 2.5" hard drive in place of the optical drive (via a specific ASUS adapter). Please refer to the complete PDF user manual available on this page for precise details regarding compatible configurations and disassembly procedures.

Question 7

My ROG Kunai 3 shows 'not connected' on my ASUS phone - how to reconnect the controller?

Accepted Answer

If your ROG Kunai 3 shows 'not connected' in the hardware info of your ASUS ROG Phone, here’s how to reconnect it:

If the controller was already paired before

Simply press the home button on the controller. It should automatically reconnect to the last paired phone. Make sure that your phone's Bluetooth is turned on.

If the controller does not reconnect

Check the battery level via the LED indicator (solid red = very low battery 0-25%)
If the battery is very low, connect the controller via USB Type-C to charge it (solid white = charging)
Try restarting the controller: hold the home button for 10 seconds, then press it again to turn it on

Complete Bluetooth re-pairing

If the above steps do not work, re-pair the controller:

Set the connection switch to Bluetooth (side of the controller)
Press the home button to turn on the controller - the LED indicator blinks slowly in blue
Hold the home button for 3 to 5 seconds until the indicator blinks quickly in blue (pairing mode active)
On your phone, go to Settings > Bluetooth
Select 'ROG Kunai 3 Gamepad' from the list of available devices

The controller is now reconnected. The LED indicator will turn green (battery 90-100%) or yellow (battery 25-90%) depending on the charge level.

Question 8

Is it recommended to install the ZenWiFi AX Hybrid XP4 in a meterkast?

Accepted Answer

No, it is not recommended to install the ZenWiFi AX Hybrid XP4 in a meterkast.

According to the product specifications, this device has strict operating conditions:

Temperature: 0-40°C
Humidity: 50-90%
Ventilation: Adequate ventilation is necessary for optimal operation

Why a meterkast is not suitable:

Electrical panels often become hotter than 40°C due to heat generated by electrical equipment
Humidity is generally higher than 90%, especially in case of condensation
Ventilation is often insufficient for this type of closed enclosure
Electromagnetic interference from the meterkast (circuit breakers, wiring, transformers) can degrade WiFi signal quality

Best placement: Install the ZenWiFi AX Hybrid XP4 in a central area of your home, on a shelf or table in an open space, away from thick metal objects and in a well-ventilated location.

Question 9

Is the ZenWiFi AX Hybrid XP4 compatible with devolo 1200+ powerline adapters?

Accepted Answer

The ZenWiFi AX Hybrid XP4 is equipped with a Powerline Backhaul function using the HomePlug AV1300 standard, allowing it to create an upstream link via your home's electrical network to connect the mesh system nodes together.

However, compatibility with the Devolo 1200+ is not guaranteed. Devolo 1200+ adapters generally use the HomePlug AV standard (an earlier version), while the XP4 operates on AV1300. Although these two standards are technically backward compatible, they rarely work together at optimal speeds on the same electrical network.

Potential issues: If you connect the Devolo 1200+ and the XP4 on the same electrical circuit, they may recognize each other but with degraded performance. The speed will be limited to the older version of the protocol (HomePlug AV), which can significantly reduce transfer speeds and cause connection instability. Additionally, the XP4 is designed to operate in a coherent system with other ASUS devices using AV1300.

Recommendation: To avoid conflicts and performance issues, do not use the Devolo 1200+ simultaneously with the ZenWiFi XP4 system. If you already have the Devolo, it is advisable to prioritize the ASUS XP4 mesh system with PowerLine Backhaul rather than mixing the two brands. If you absolutely need to extend your network, prefer a wired Ethernet connection (Ethernet Backhaul) or WiFi 6 (WiFi Backhaul) between the XP4 nodes.

To optimize Powerline on XP4: Always connect cables directly to a wall outlet (no extensions), use grounded outlets (3 prongs), and avoid plugging into the same circuit as high-energy-consuming devices (radiator, washing machine, air conditioner).

Question 10

How to use the WPS function on the ASUS RT-AC1750U router to connect devices to the Wi-Fi network?

Accepted Answer

The WPS (Wi-Fi Protected Setup) function on the ASUS RT-AC1750U router allows you to easily and quickly connect devices to your Wi-Fi network without having to manually enter the security key.

Using WPS on the RT-AC1750U

1. WPS Button Method (the simplest)

Locate the WPS button on your ASUS RT-AC1750U router (usually located on the back or side of the device).
Press this button.
Within 2 minutes, activate the WPS function on the device you want to connect (smartphone, tablet, printer, etc.).
The connection will be established automatically without needing to enter the Wi-Fi key.

2. WPS PIN Code Method

Access the router's administration interface via a web browser by entering the router's IP address (often 192.168.1.1 or router.asus.com).
Log in with your administrator credentials.
In the section dedicated to WPS, note or enter the PIN code of the device you want to connect.
Start the pairing procedure by entering this PIN in the router's interface.
The connection will be established automatically after validation.

Limitations and Compatibilities

WPS works with networks using WPA-Personal and WPA2-Personal security modes.
It is not compatible with networks using WEP, WPA-Enterprise, or RADIUS.

This function is very convenient for quickly connecting devices without having to memorize or enter the Wi-Fi key, while maintaining an adequate level of security.

User manual ASUS : user manuals and guides in PDF

Models ASUS most viewed

Browse manuals ASUS by appliance type

Recent questions about devices ASUS