Q: How to pair the remote control with the hood?

Remote control pairing procedure TLC: To pair the remote control with your Airforce F181 hood, follow these precise steps: Turn off the power to the hood for at least 10 seconds Restore the power Within the first 5 seconds, press the lighting button T4 and release it once the lights turn on In the next 5 seconds, press the motor button T2 and release it when the lights turn off Wait about 10 seconds: the hood is then ready for use Button functions: T1 (+) increases the speed, T3 (-) decreases it, T2 (On/Off) activates/deactivates the motor, T4 (On/Off) controls the lighting. In case of interference: If the remote control does not respond correctly due to interference from other nearby wireless devices, activate the transmission code change by simultaneously pressing and holding the T1 (+) and T3 (-) buttons for at least 10 seconds. Once the code is changed, repeat the pairing procedure described above.

Question 1

How to pair the remote control with the hood?

Accepted Answer

Remote control pairing procedure TLC:

To pair the remote control with your Airforce F181 hood, follow these precise steps:

Turn off the power to the hood for at least 10 seconds
Restore the power
Within the first 5 seconds, press the lighting button T4 and release it once the lights turn on
In the next 5 seconds, press the motor button T2 and release it when the lights turn off
Wait about 10 seconds: the hood is then ready for use

Button functions: T1 (+) increases the speed, T3 (-) decreases it, T2 (On/Off) activates/deactivates the motor, T4 (On/Off) controls the lighting.

In case of interference: If the remote control does not respond correctly due to interference from other nearby wireless devices, activate the transmission code change by simultaneously pressing and holding the T1 (+) and T3 (-) buttons for at least 10 seconds. Once the code is changed, repeat the pairing procedure described above.

Question 2

Why is my Airforce F0 D2 hood not working properly, not sucking, and making a whistling noise?

Accepted Answer

If your Airforce F0 D2 hood is not sucking properly and is producing a whistling noise, the problem usually comes from a clogged filter or an obstruction in the exhaust duct. Here’s how to diagnose and resolve the malfunction by following the specific instructions for your model.

Check and clean the grease filter as a priority. This metal filter should be cleaned once a month with a non-aggressive detergent, either by hand or in the dishwasher at low temperature during a short cycle. A clogged filter drastically reduces suction capacity and can generate a characteristic whistling noise. After cleaning, reinstall it correctly and test the device. Washing in the dishwasher may cause slight discoloration, but this does not affect filtering performance in any way.

Inspect the exhaust duct if you are using the extraction version. Your Airforce F0 D2 hood comes with a top air outlet B for venting smoke outside (exhaust duct not included). Check that the duct is not obstructed by grease deposits, debris, or bird nests. The connections should be well secured without air leaks, as poorly fitted connections can cause whistling. A partially obstructed duct limits suction and can create a characteristic noise.

Check the operating mode and suction power. Your hood has three power levels: minimum (1), medium (2), and maximum (3). The minimum power sucks at 60-70 m³/h and may seem insufficient to eliminate smoke. First, test at maximum power (3) to see if suction improves. Each speed operates for 5 minutes before the hood automatically turns off; press the button again to extend operation. We recommend turning on the hood 5 minutes before cooking and letting it run for about 15 minutes after cooking is finished.

If you have a filtering version, check the charcoal filter. The active charcoal filter F should be replaced every 6 months under normal use. This filter traps bad odors and cannot be washed or recycled. A used or saturated charcoal filter reduces suction efficiency and may allow odors to escape. If your hood operates in filtering mode with air recycling through the upper grille G, ensure that this filter is regularly maintained.

Perform additional diagnostics if the issue persists. Clean the inside of the hood with a cloth soaked in denatured alcohol (except for the area behind the grease filter). Also, check for any objects or dirt blocking the fan. If after these checks the whistling persists and suction remains weak, turn off the hood and unplug it from the power supply before any further intervention. An unbalanced fan, a defective motor, or internal damage may require specialized professional intervention.

User manual Airforce : user manuals and guides in PDF

Models Airforce most viewed

Browse manuals Airforce by appliance type

Recent questions about devices Airforce