Q: The remote control does not respond during the initial installation of the air conditioner

Common issue: If your BEKO BRVPF125 does not respond to the remote control commands during the first use, follow these checks in order. Immediate checks Remote control batteries: The air conditioner comes with 2 batteries included. Check that they are correctly inserted into the remote control with the correct polarity (+/-). Obstacle in front of the sensor: Point the remote control directly at the infrared receiver of the air conditioner (usually on the front panel). Ensure there are no obstructions. Plastic protection: If the remote control is new, check that no plastic protection covers the infrared sensor. If the problem persists Replace the batteries with new ones (make sure you are using the correct type of battery). Turn off the air conditioner for 30 seconds, then turn it back on to reset it. Test with the remote control at a reasonable distance (2-3 meters), directly aimed at the unit. Note: Some buttons on the remote control (especially specialized functions like SLEEP, TURBO, SILENCE) may not be available depending on your device configuration. The main functions (MODE, SWING, TIMER, power) should work after following these steps.

Q: Should the fan continue to run when the air conditioning is turned on?

Yes, the fan should continue to run when you turn on the BEKO BSVOM 120 air conditioning in cooling mode. This is a normal and necessary behavior. Here’s how the fan operates: In cooling mode: the fan runs continuously to circulate cold air in the room as long as the compressor is active In fan only mode: the fan operates without active cooling The fan speed may vary depending on the temperature settings and the selected mode If your fan is not rotating or stops abnormally when the unit is running, this may indicate: A problem with the fan motor A malfunction of the internal controls A safety shutdown triggered by a detected anomaly Check the operation using the remote control and refer to the troubleshooting section of your manual for additional diagnostic steps.

Q: Why does the BEKO BP209C air conditioner only blow air to the right?

The BP209C has a fixed air outlet and is not adjustable. This means that air always escapes from the front of the unit in a direction determined by its design, with no possibility to manually change this trajectory with adjustable louvers. If the air seems to be blowing mainly to the right, it may be due to: A slight tilt: Ensure that the unit is resting on a perfectly flat and stable surface. Even a very slight slope can divert the airflow. Ambient air currents: Natural air drafts in the room (open doors, windows, other appliances) can redirect the air once it leaves the unit. Clutter around the unit: Make sure to maintain the recommended space of 30 cm minimum around all sides for air to circulate freely without obstruction from the side inlets. If you need to direct the air in other directions, you can reposition the unit in the room or use an external deflector (like a lightweight board) to slightly redirect the airflow without completely blocking the outlet.

Question 1

Does the BX 112H air conditioner have a water tank that needs to be emptied?

Accepted Answer

Yes, the BEKO BX 112H air conditioner has a water tank that needs to be emptied regularly.

When the water level in the lower tank reaches a predetermined level, the digital display shows the code "P1". This is the signal that you need to drain the tank immediately.

Two drainage methods available:

Dehumidification mode (continuous drainage): Remove the upper drainage plug and connect a drainage hose (provided) to an external drainage system. This method allows for automatic and continuous drainage.
Manual drainage of the lower tank: When the message "P1" appears, carefully move the unit to the drainage location, then remove the plug from the lower drainage device and let the water drain out. Caution: the volume can be significant depending on the tank's fill level. It is recommended to drain outside or over a basin to avoid flooding your room.

If your unit has a drainage pump, you can also remove the pump plug and connect the drainage hose.

Question 2

The remote control does not respond during the initial installation of the air conditioner

Accepted Answer

Common issue: If your BEKO BRVPF125 does not respond to the remote control commands during the first use, follow these checks in order.

Immediate checks

Remote control batteries: The air conditioner comes with 2 batteries included. Check that they are correctly inserted into the remote control with the correct polarity (+/-).
Obstacle in front of the sensor: Point the remote control directly at the infrared receiver of the air conditioner (usually on the front panel). Ensure there are no obstructions.
Plastic protection: If the remote control is new, check that no plastic protection covers the infrared sensor.

If the problem persists

Replace the batteries with new ones (make sure you are using the correct type of battery).
Turn off the air conditioner for 30 seconds, then turn it back on to reset it.
Test with the remote control at a reasonable distance (2-3 meters), directly aimed at the unit.

Note: Some buttons on the remote control (especially specialized functions like SLEEP, TURBO, SILENCE) may not be available depending on your device configuration. The main functions (MODE, SWING, TIMER, power) should work after following these steps.

Question 3

What is the diameter of the air exhaust hose of the BEKO BPN109C air conditioner?

Accepted Answer

The technical information for the BEKO BPN109C air conditioner is not directly accessible to confirm the exact size of the exhaust hose, so we recommend checking:

The PDF of the complete manual - the size is usually listed in the "Technical Specifications" or "Installation" section
The installation documentation provided with the unit, which specifies the diameter of the duct
Typically, for BEKO portable air conditioners, the diameter of the exhaust hose is 150 mm, but this value should be confirmed in your documentation

Contact BEKO customer service if needed for the precise dimension if the PDF manual does not clearly mention it.

Question 4

Why does my BEKO BEEPGH 125 air conditioner emit repeated beeps in sleep mode?

Accepted Answer

The manual for the BEKO BEEPGH 125 does not explicitly document what the repeated beeps mean when activating or operating in sleep mode. However, here is what we know:

Normal operation of sleep mode

The sleep mode is designed to reduce energy consumption during your rest. It can only be activated via the remote control and:

In cooling: the temperature increases by 1°C per hour for the first 2 hours
In heating: the temperature decreases by 1°C per hour for the first 2 hours
Operates for 8 hours, then maintains the final setting

Possible causes of repeated beeps

Activation confirmation - A single beep may indicate that the sleep mode has been activated correctly
Error code - If the repeated beeps follow a pattern (for example, 3 beeps, pause, 3 beeps), check the display: error codes appear as E, P, F, EH, EL, EC, PH, PL, PC
GoClean function - The air conditioner may emit a

Question 5

What do the repeated beeping signals mean when the BEKO BEEPGH 125 air conditioner is in sleep mode?

Accepted Answer

The BEKO BEEPGH 125 air conditioner emits beeping signals to alert you to function changes or the achievement of the programmed temperature during sleep mode.

According to the documentation, the SLEEP function is designed to reduce energy consumption during nighttime rest. Here’s how it works:

In cooling mode: the unit gradually increases the temperature by 1°C per hour during the first two hours, then maintains the new temperature until automatic shut-off after 8 hours.
In heating mode: the unit gradually decreases the temperature by 1°C per hour during the first two hours, then maintains the new temperature until automatic shut-off after 8 hours.

The repeated beeping signals during this mode may indicate:

Activation of the sleep function from the remote control
Completion of the programmed temperature changes
Automatic shut-off after 8 hours of operation
Activation of the GoClean function (automatic cleaning) which produces a characteristic sound

The sleep function is only available from the remote control and does not work in fan or dehumidification mode. If the signals persist or seem abnormal, check that the function has been correctly activated from the remote control.

Question 6

Should the fan continue to run when the air conditioning is turned on?

Accepted Answer

Yes, the fan should continue to run when you turn on the BEKO BSVOM 120 air conditioning in cooling mode. This is a normal and necessary behavior.

Here’s how the fan operates:

In cooling mode: the fan runs continuously to circulate cold air in the room as long as the compressor is active
In fan only mode: the fan operates without active cooling
The fan speed may vary depending on the temperature settings and the selected mode

If your fan is not rotating or stops abnormally when the unit is running, this may indicate:

A problem with the fan motor
A malfunction of the internal controls
A safety shutdown triggered by a detected anomaly

Check the operation using the remote control and refer to the troubleshooting section of your manual for additional diagnostic steps.

Question 7

Why does the BEKO BP209C air conditioner only blow air to the right?

Accepted Answer

The BP209C has a fixed air outlet and is not adjustable. This means that air always escapes from the front of the unit in a direction determined by its design, with no possibility to manually change this trajectory with adjustable louvers.

If the air seems to be blowing mainly to the right, it may be due to:

A slight tilt: Ensure that the unit is resting on a perfectly flat and stable surface. Even a very slight slope can divert the airflow.
Ambient air currents: Natural air drafts in the room (open doors, windows, other appliances) can redirect the air once it leaves the unit.
Clutter around the unit: Make sure to maintain the recommended space of 30 cm minimum around all sides for air to circulate freely without obstruction from the side inlets.

If you need to direct the air in other directions, you can reposition the unit in the room or use an external deflector (like a lightweight board) to slightly redirect the airflow without completely blocking the outlet.

Question 8

How to control or adjust the direction of the airflow of the BEKO BP209C air conditioner?

Accepted Answer

The BEKO BP209C model does not have a manually adjustable air deflector. This portable cooling unit is designed with a fixed front air outlet, which means that air always escapes from the front in a determined direction.

If you notice that the air seems to be directed to the right, it may be due to:

The position of the unit - The air conditioner should be placed on a flat and stable surface. Check that it is not slightly tilted, which could alter the airflow trajectory.
Obstacles around the unit - Ensure that the side air inlets are not blocked (the manual recommends at least 30 cm of clearance around the unit for optimal circulation).
Ambient air currents - Natural flows in the room (open windows, other appliances) can deflect the outgoing airflow.

To optimize the distribution of cooled air in your room, make sure the unit is properly ventilated on the sides and adjust its position to promote better overall circulation. You can also use the fan mode (without cooling) to test the airflow trajectory based on the unit's positioning.

Question 9

What diameter should the drain hose of the BEKO BS207C air conditioner have?

Accepted Answer

The manual for the BEKO BS207C air conditioner does not specify the exact diameter of the drain hose.

However, the manual specifies the following technical characteristics of the drainage hose:

Length: between 28 and 150 cm
Installation: the flat end of the fittings must be inserted into the window kit
Bend: the hose must not have a bend radius greater than 45°
Important: do not use replacement hoses - never replace the original hose with another hose, as this may cause the device to malfunction

Since the manufacturer strongly discourages any replacement of the original hose, we recommend ordering an official BEKO replacement hose from the after-sales service or an authorized BEKO dealer, who will provide you with the correct diameter compatible with your BS207C.

Question 10

How to close the deflector of the BEKO BEEPGH 095 air conditioner?

Accepted Answer

The deflector of the BEKO BEEPGH 095 has two types of controls depending on its direction:

Vertical Control (oscillation)

Use the SWING button on the remote control to adjust the vertical angle of the airflow. This button controls the automatic oscillation of the deflector. If you want to fix a specific position, simply turn off the oscillation using the same button.

Horizontal Control (manual)

To adjust the horizontal direction of the deflector, you need to do it manually. Grab the deflector rod and position it at the desired angle. Do not force the movement to avoid misalignment of the system.

If the deflector is unresponsive

If after a manual adjustment the deflector remains misaligned, the unit has an angle memorization function. Proceed as follows:

Turn off the unit (wait a few seconds)
Turn it back on
The deflector should automatically return to its previous position

Warning

Do not set the deflector too vertically in cooling or dehumidification mode. Condensation may form on the blades and drip onto your furniture.

User manual BEKO Air conditioner : user manuals and guides in PDF

Models BEKO Air conditioner most viewed

Other categories BEKO

Recent questions about Air conditioner BEKO