Q: Why does the lighting turn on every time the door of the BEKO B5RCNE416HG refrigerator is opened?

The lighting of the BEKO B5RCNE416HG refrigerator is an LED source that automatically activates each time the door is opened. This system makes it easier to place and locate food inside the appliance. The PDF of this manual does not specify the exact colors of this lighting. If you observe lights of different colors (red, green, or blue), it may be either an illumination of the inside of the compartment or potentially indicator lights from the control panel. The refrigerator's control panel has several visual indicators that light up to indicate the status of different functions (fast freezing, vacation mode, temperature errors, etc.). Replacing the bulb or LED source must be carried out by a qualified technician - do not attempt this intervention yourself.

Q: My BEKO CN147243GW refrigerator makes a strange noise at startup with a clicking sound. What does this mean?

Good news: the noise you are describing is very likely normal compressor operation . According to the technical manual for the BEKO CN147243GW, this model produces a sound level of 39 dB(A) and the startup noises of the compressor, the flow of refrigerant, and the crackling sounds are part of normal operations. Why this noise has intensified: Your fridge was probably in correction mode for a thermal excursion (detected too high temperature). After unplugging and replugging, the system reset and the compressor restarted normally - hence the perception of the noise. The pink icon with exclamation point This icon indicated a high temperature alert detected by the system. This can occur after: Prolonged door opening Overloading with hot products Temporary malfunction of the cooling system By resetting the device (unplugging/replugging), you cleared this alert and the compressor was able to operate normally. What to do now The noise gradually decreases as the compressor reaches normal operating mode - this is expected Check that the internal temperature stabilizes around 4°C (position 3 on the BEKO CN147243GW selector) Ensure that the doors close properly and without obstruction If the alert icon reappears, check that the appliance is not placed near a heat source (the manual recommends at least 30cm) If the compressor does not start within 6 minutes or if the noise becomes abnormally loud and persists, contact an authorized BEKO technician

Q: How to clean or access the water collection tray located at the back of the BEKO TSE1402F?

The BEKO TSE1402F has a water collection tray (evaporation tray) located at the back of the appliance . Defrost water accumulates there automatically via the internal drainage path. Accessing and cleaning the tray The TSE1402F manual recommends unplugging the appliance before any intervention . Although the manual does not detail the disassembly of the tray, here is what you need to know: The tray is located at the back, above the compressor It should be accessible by slightly tilting the refrigerator forward or by removing the rear base For cleaning, use a damp cloth – do not pour water directly on electrical components Warning: Do not let water flow into the lamp housing or on other electrical components If you need to work directly near the compressor or the refrigeration circuit, contact a certified BEKO technician , as these areas require specific skills. For simple cleaning operations of the tray, gently lift the appliance or tilt it carefully.

Question 1

My Beko CN142240X refrigerator is not cooling after a power outage

Accepted Answer

If your Beko CN142240X refrigerator is not cooling after power is restored, here are the steps to follow:

After a power outage

Wait at least 5 minutes before turning the appliance back on. The refrigeration system needs time to rebalance the refrigerant pressure.
The compressor is protected by a thermal device that may trigger during rapid restarts. Allow about 6 minutes for the appliance to restart automatically.
Once restarted, wait several hours for complete temperature stabilization (2-8°C in the fridge, -18 to -24°C in the freezer).

If the refrigerator still refuses to cool

Check that the doors close properly and that the seals are not damaged.
Check the thermostat settings - if they were changed during the outage, return them to the recommended values.
If the problem persists after 6 minutes and the above checks, contact an authorized Beko service technician.

Question 2

Why does the lighting turn on every time the door of the BEKO B5RCNE416HG refrigerator is opened?

Accepted Answer

The lighting of the BEKO B5RCNE416HG refrigerator is an LED source that automatically activates each time the door is opened. This system makes it easier to place and locate food inside the appliance.

The PDF of this manual does not specify the exact colors of this lighting. If you observe lights of different colors (red, green, or blue), it may be either an illumination of the inside of the compartment or potentially indicator lights from the control panel. The refrigerator's control panel has several visual indicators that light up to indicate the status of different functions (fast freezing, vacation mode, temperature errors, etc.).

Replacing the bulb or LED source must be carried out by a qualified technician - do not attempt this intervention yourself.

Question 3

My BEKO CN147243GW refrigerator makes a strange noise at startup with a clicking sound. What does this mean?

Accepted Answer

Good news: the noise you are describing is very likely normal compressor operation. According to the technical manual for the BEKO CN147243GW, this model produces a sound level of 39 dB(A) and the startup noises of the compressor, the flow of refrigerant, and the crackling sounds are part of normal operations.

Why this noise has intensified: Your fridge was probably in correction mode for a thermal excursion (detected too high temperature). After unplugging and replugging, the system reset and the compressor restarted normally - hence the perception of the noise.

The pink icon with exclamation point

This icon indicated a high temperature alert detected by the system. This can occur after:

Prolonged door opening
Overloading with hot products
Temporary malfunction of the cooling system

By resetting the device (unplugging/replugging), you cleared this alert and the compressor was able to operate normally.

What to do now

The noise gradually decreases as the compressor reaches normal operating mode - this is expected
Check that the internal temperature stabilizes around 4°C (position 3 on the BEKO CN147243GW selector)
Ensure that the doors close properly and without obstruction
If the alert icon reappears, check that the appliance is not placed near a heat source (the manual recommends at least 30cm)
If the compressor does not start within 6 minutes or if the noise becomes abnormally loud and persists, contact an authorized BEKO technician

Question 4

How to clean or access the water collection tray located at the back of the BEKO TSE1402F?

Accepted Answer

The BEKO TSE1402F has a water collection tray (evaporation tray) located at the back of the appliance. Defrost water accumulates there automatically via the internal drainage path.

Accessing and cleaning the tray

The TSE1402F manual recommends unplugging the appliance before any intervention. Although the manual does not detail the disassembly of the tray, here is what you need to know:

The tray is located at the back, above the compressor
It should be accessible by slightly tilting the refrigerator forward or by removing the rear base
For cleaning, use a damp cloth – do not pour water directly on electrical components
Warning: Do not let water flow into the lamp housing or on other electrical components

If you need to work directly near the compressor or the refrigeration circuit, contact a certified BEKO technician, as these areas require specific skills. For simple cleaning operations of the tray, gently lift the appliance or tilt it carefully.

Question 5

How do I adjust the temperature of the BEKO RCNE560E61ZXN refrigerator to make it colder?

Accepted Answer

To increase the coldness of your BEKO RCNE560E61ZXN refrigerator, you need to turn the temperature control knob to the highest numbers.

Steps:

Locate the thermostat knob inside the fridge compartment (usually at the top right or left)
Turn it towards the higher numbers for more cold (up to the maximum position)
The numbers directly indicate the temperature in degrees Celsius

Temperature Guidelines:

Fridge: range from 1°C to 8°C; recommended setting 4°C
Freezer: range from -18°C to -24°C; recommended setting -18°C

Wait 2 to 4 hours after making adjustments before checking if the desired temperature is reached, as the appliance system takes time to stabilize.

Question 6

Why is my BEKO B5RCNE565HGB refrigerator not reaching the set temperature?

Accepted Answer

If your BEKO B5RCNE565HGB refrigerator is not reaching the temperature you have set, here are the most common causes and solutions to check:

Essential Checks

Check the thermostat - Ensure that the temperature setting knob has not been accidentally changed. Turn it slightly down if the temperature seems insufficient.
Make sure the fridge is plugged in - Confirm that the appliance is properly connected to the power outlet and that the electrical socket is functioning.
Leave the fridge running - If you have just plugged it in, wait 2 to 4 hours for the temperature to reach its optimal level.
Check the door seals - Worn or dirty seals can let cold air escape. Clean them with a damp cloth or replace them if they are damaged.
Clear the vents - Ensure that the air circulation vents inside the fridge are not blocked by food or packaging.

If the problem persists

If after these checks the temperature still does not stabilize at the desired level, there may be a technical issue with the compressor or the cooling system. In this case, contact BEKO customer service or an authorized repair technician for a complete diagnosis.

Question 7

Why is my BEKO RDSA240K20WN fridge leaking water?

Accepted Answer

The BEKO RDSA240K20WN features an automatic defrost system that generates condensation. This water should drain through the drain hole located at the back or bottom of the appliance. If water is leaking from your fridge, it is usually due to one of these two reasons:

1. Clogged drain hole (most common cause)

The drainage pipe may be blocked by debris or limescale. Clean the drain hole with a pipe cleaner or a small rigid tube to clear the passage. The defrost water should be able to flow freely.

2. Poorly positioned fridge

Your RDSA240K20WN must be perfectly horizontal. If the fridge is tilted, the water will not drain properly to the outlet. Check that all four feet of the appliance are adjusted to the same level (use a level if possible).

Additional tip: Also check that the fridge is not installed in an environment that is too cold (below 10°C) - this can disrupt the defrost system.

Question 8

Why does my BEKO RCNA305K20S refrigerator not go below 10°C?

Accepted Answer

If your RCNA305K20S does not go below 10°C, here are the checks to perform:

Priority Checks

Temperature dial positioning: The setting is located on the ceiling of the refrigerator compartment with a range from 1 (minimum) to 4 (maximum cold). If you are on position 1 or 2, gradually increase to 3-4 and wait 24 hours to allow the temperature to stabilize.
Blocked fans: Check that the fans are not obstructed by food items or packaging. These can quickly raise the internal temperature. Clear any obstacles.
Condenser cleaning: Regularly dust the condenser with a soft brush or vacuum. A dirty condenser reduces cooling efficiency.
Ventilation space: Ensure that the appliance is well away from direct heat sources (radiators, stove, direct sunlight) and has free air circulation all around.
Door closure: Check that the door closes properly and that the seal is not damaged or dirty.

After these checks and 24 hours of stabilization, the temperature should be correct (below 5°C on average). If the problem persists, there may be an internal malfunction of the refrigeration system that requires technical intervention.

Question 9

How to reposition the doors of the Beko RDSA310K40WN refrigerator?

Accepted Answer

To reposition the doors of your Beko RDSA310K40WN refrigerator (reverse the door opening), refer to Figure 7 in the provided manual. This figure presents a numbered diagram that precisely explains each step to follow.

Repositioning Steps

Strictly follow the numerical order indicated in Figure 7
Use basic and appropriate tools to carry out the operation
The operation does not require specialized equipment

This operation allows you to change the opening direction of the refrigerator and freezer doors according to your space needs and kitchen layout. Figure 7 in your manual uses numbered visual diagrams to make the operation simple and safe to perform.

Question 10

What is the white component located on top of the BEKO B5RCNE416HG refrigerator?

Accepted Answer

The rectangular white component located on top of the BEKO B5RCNE416HG refrigerator is a spacer (plastic wedge) provided with the appliance. It is an essential part for the proper functioning of your refrigerator.

What is this spacer for?

The plastic wedges help maintain sufficient air space between the refrigerator and the wall, particularly at the rear ventilation cover. This space is crucial for:

Ensuring adequate air circulation around the appliance
Preventing compressor overheating
Optimizing the cooling of the appliance

Required installation

According to the manual for the BEKO B5RCNE416HG, these wedges must be attached to the ventilation cover located at the back of the refrigerator. The manual also recommends leaving a space of at least 5 cm between the appliance and the ceiling, the back wall, and the side walls for optimal ventilation.

Important: Do not discard this component - it is necessary for the correct operation and longevity of your appliance.

User manual BEKO Refrigerator : user manuals and guides in PDF

Models BEKO Refrigerator most viewed

Other categories BEKO

Recent questions about Refrigerator BEKO