Q: How to install the feet of the ARDES AR5T1001 column fan?

Installing the feet is mandatory for safety - the fan must never operate without its 4 supports. Before you begin Make sure the fan is turned off and unplugged from the electrical outlet Prepare a flat and stable space for assembly Parts to assemble You need the 4 supports provided: 2 short supports 2 long supports Installation steps Assemble the 4 supports (2 short and 2 long) following the diagram illustrated in the PDF manual Secure them properly to the base of the fan according to the diagram Check that all 4 feet are properly in place before any use Important points The fan must remain in a vertical and upright position Place it on a flat and stable surface Only plug in the device after you have completely finished the assembly Incorrect installation may damage the equipment or create a risk If a support does not fit correctly or a part is resistant, refer to the detailed assembly diagram in the PDF manual to check the exact orientation of the parts.

Q: Some parts listed in the manual do not exist on my AR5ST40PW fan. What should I do?

You are describing a significant discrepancy between the manual and your actual device: parts 2 (blade attachment) and 5 (rear grille attachment) are not present on your model, the base has a different shape, and there is a missing seal between the two parts of the grille. This very likely indicates that the manual displayed on this page is not exactly the right one for your ARDES AR5ST40PW model , even if the reference seems to match. Several reasons could explain this: Your fan is a slightly different version (earlier or later revision) with a simplified or modified attachment system It is a regional or batch variant with different components The manual may have been incorrectly indexed and associated with the wrong model To correctly assemble your device without following an unsuitable manual , I advise you to: Check that the base and the stand are securely attached to the central support with the available screws Assemble the rear grille directly without parts 2 and 5 (which seem not to exist on your model) Tighten the height adjustment knob (part 13) firmly so that the whole assembly is stable For the missing seal between the two parts of the grille : if you notice any play or instability, you can add thick tape or a thin rubber seal between the two grilles before assembling them Important advice : take a photograph of your complete fan and the missing parts from the manual, then contact ARDES directly to confirm that you have the correct version or to send you the correct manual. Notice-facile.com can then correct or replace this manual if it is indeed an indexing error.

Q: Should the screw at the back of the AR5ST40PW fan be removed before assembling the blade?

Yes, you must absolutely remove this screw. This screw at the back holds a transport or safety part in place. It must be removed so that you can access the rear grille and properly assemble the blade. Assembly Steps: Remove the screw at the back with an appropriate screwdriver Once removed, the rear grille and rear cylinder should come off easily Install the blade fixing part (part 2) Attach the 40 cm blade (part 4) Replace the rear grille (part 5) Assemble the front grille Once this screw is removed, the assembly of the rest of the fan should proceed without any issues.

Q: How to block the screw on the shaft of the ARDES AR5M39 fan?

To block the screw on the shaft of the ARDES AR5M39 fan: The device uses a retaining ring (or locking ring) that fits onto the motor shaft. Here’s how to proceed: Steps to assemble the shaft Insert the retaining ring onto the motor shaft Turn the ring clockwise until it is fully tightened Ensure that the ring does not turn easily - it must be securely locked The retaining ring is the essential component that keeps the screw and all parts (rear grille, blades) firmly attached to the shaft during use. If this ring is missing or damaged, the fan cannot operate safely. Important points: The locking ring must be included in your packaging - check the list of 25 parts Do not force the tightening - the ring should turn smoothly until fully engaged If the ring is corroded or damaged, contact ARDES support for a replacement part

Q: Why does the remote control of the ARDES AR5T1001 fan respond poorly or slowly to commands?

If your AR5T1001 fan remote control responds poorly even after checking the batteries, here are the key points to check: Essential Checks Range and angle of the sensor : The remote control of the AR5T1001 has a maximum range of 5 meters with a 45° angle towards the fan's sensor. Move closer and aim directly at the infrared receiver of the fan. Quality batteries : Use two new AAA 1.5V batteries from a reputable brand. Weak or used batteries lead to a very short range and intermittent responses. Correct polarity : Ensure that the batteries are installed in the correct direction (+ and -) according to the indications inside the remote control compartment. LED screen : The remote control's screen turns off after 5 seconds of inactivity to save battery. If you see no reaction after pressing a button, the batteries are likely too weak. Sensor obstruction : Make sure nothing is blocking the infrared sensor located at the top of the fan. Dust, protective films, or objects in front of the receiver can block the signal. If the problem persists If the remote control still does not respond after these checks, the fault may lie with either the fan's receiver sensor or the remote control itself. In this case, contact an authorized ARDES service center rather than attempting to disassemble the device yourself. Your fan is covered by a 24-month warranty.

Question 1

How to install the feet of the ARDES AR5T1001 column fan?

Accepted Answer

Installing the feet is mandatory for safety - the fan must never operate without its 4 supports.

Before you begin

Make sure the fan is turned off and unplugged from the electrical outlet
Prepare a flat and stable space for assembly

Parts to assemble

You need the 4 supports provided:

2 short supports
2 long supports

Installation steps

Assemble the 4 supports (2 short and 2 long) following the diagram illustrated in the PDF manual
Secure them properly to the base of the fan according to the diagram
Check that all 4 feet are properly in place before any use

Important points

The fan must remain in a vertical and upright position
Place it on a flat and stable surface
Only plug in the device after you have completely finished the assembly
Incorrect installation may damage the equipment or create a risk

If a support does not fit correctly or a part is resistant, refer to the detailed assembly diagram in the PDF manual to check the exact orientation of the parts.

Question 2

Some parts listed in the manual do not exist on my AR5ST40PW fan. What should I do?

Accepted Answer

You are describing a significant discrepancy between the manual and your actual device: parts 2 (blade attachment) and 5 (rear grille attachment) are not present on your model, the base has a different shape, and there is a missing seal between the two parts of the grille.

This very likely indicates that the manual displayed on this page is not exactly the right one for your ARDES AR5ST40PW model, even if the reference seems to match. Several reasons could explain this:

Your fan is a slightly different version (earlier or later revision) with a simplified or modified attachment system
It is a regional or batch variant with different components
The manual may have been incorrectly indexed and associated with the wrong model

To correctly assemble your device without following an unsuitable manual, I advise you to:

Check that the base and the stand are securely attached to the central support with the available screws
Assemble the rear grille directly without parts 2 and 5 (which seem not to exist on your model)
Tighten the height adjustment knob (part 13) firmly so that the whole assembly is stable
For the missing seal between the two parts of the grille: if you notice any play or instability, you can add thick tape or a thin rubber seal between the two grilles before assembling them

Important advice: take a photograph of your complete fan and the missing parts from the manual, then contact ARDES directly to confirm that you have the correct version or to send you the correct manual. Notice-facile.com can then correct or replace this manual if it is indeed an indexing error.

Question 3

Should the screw at the back of the AR5ST40PW fan be removed before assembling the blade?

Accepted Answer

Yes, you must absolutely remove this screw.

This screw at the back holds a transport or safety part in place. It must be removed so that you can access the rear grille and properly assemble the blade.

Assembly Steps:

Remove the screw at the back with an appropriate screwdriver
Once removed, the rear grille and rear cylinder should come off easily
Install the blade fixing part (part 2)
Attach the 40 cm blade (part 4)
Replace the rear grille (part 5)
Assemble the front grille

Once this screw is removed, the assembly of the rest of the fan should proceed without any issues.

Question 4

How to remove the plastic cap from the AR5ST40PW fan?

Accepted Answer

The plastic cap blocking the assembly of the AR5ST40PW fan is generally a transport protection that must be removed before use.

Removal procedure:

Make sure that the safety screw at the back has been removed (essential step 1 of the assembly). This screw sometimes keeps the cap in place.
Pull firmly and steadily on the cap rather than yanking it - it may require a slight rotation to come loose.
If the cap does not budge, check that no label or protective film is obstructing the device - the manual specifies to remove all protections before first use.

If the cap remains stuck:

If after removing the safety screw and taking off all films, the cap remains immovable, this may indicate a manufacturing defect. Your fan is guaranteed for 24 months - contact ARDES customer service or your retailer for an exchange.

Question 5

How do I attach the front grille (front grille) to the AR5ST40PW fan?

Accepted Answer

The front grille of the AR5ST40PW fan should be installed last, once the rear grille and the propeller are already in place. Here’s how to proceed:

Assembly Steps

First, attach the rear grille (part no. 6) with the designated fastening piece.
Next, assemble the propeller with its fastening piece onto the motor.
Finally, clip or attach the front grille (part no. 1) onto the motor, using the positioning lugs (points A-B) as alignment markers.

Fixing Points

The front grille attaches via its fixing points on the motor body. Ensure that the positioning lugs are properly aligned before forcing. If you feel resistance, check the alignment rather than forcing it.

If You Get Stuck

If the parts do not exactly match the illustrations in the manual (which can happen depending on the manufacturing date of your fan), contact the authorized ARDES customer service mentioned in the warranty for assistance tailored to your specific model.

Question 6

How to block the screw on the shaft of the ARDES AR5M39 fan?

Accepted Answer

To block the screw on the shaft of the ARDES AR5M39 fan:

The device uses a retaining ring (or locking ring) that fits onto the motor shaft. Here’s how to proceed:

Steps to assemble the shaft

Insert the retaining ring onto the motor shaft
Turn the ring clockwise until it is fully tightened
Ensure that the ring does not turn easily - it must be securely locked

The retaining ring is the essential component that keeps the screw and all parts (rear grille, blades) firmly attached to the shaft during use. If this ring is missing or damaged, the fan cannot operate safely.

Important points:

The locking ring must be included in your packaging - check the list of 25 parts
Do not force the tightening - the ring should turn smoothly until fully engaged
If the ring is corroded or damaged, contact ARDES support for a replacement part

Question 7

Why does the remote control of the ARDES AR5T1001 fan respond poorly or slowly to commands?

Accepted Answer

If your AR5T1001 fan remote control responds poorly even after checking the batteries, here are the key points to check:

Essential Checks

Range and angle of the sensor: The remote control of the AR5T1001 has a maximum range of 5 meters with a 45° angle towards the fan's sensor. Move closer and aim directly at the infrared receiver of the fan.
Quality batteries: Use two new AAA 1.5V batteries from a reputable brand. Weak or used batteries lead to a very short range and intermittent responses.
Correct polarity: Ensure that the batteries are installed in the correct direction (+ and -) according to the indications inside the remote control compartment.
LED screen: The remote control's screen turns off after 5 seconds of inactivity to save battery. If you see no reaction after pressing a button, the batteries are likely too weak.
Sensor obstruction: Make sure nothing is blocking the infrared sensor located at the top of the fan. Dust, protective films, or objects in front of the receiver can block the signal.

If the problem persists

If the remote control still does not respond after these checks, the fault may lie with either the fan's receiver sensor or the remote control itself. In this case, contact an authorized ARDES service center rather than attempting to disassemble the device yourself. Your fan is covered by a 24-month warranty.

Question 8

Does the water tank of the ARDES AR5M39 fan have a sealing gasket?

Accepted Answer

Yes, the tank (part 19) of the ARDES AR5M39 fan has sealing gaskets. These gaskets ensure sealing when locking the tank.

How to properly close the tank

Unscrew the cap (part 23) located at the bottom of the tank by turning it counterclockwise to open
After filling with cold, clean, and previously boiled water, close the tank by turning the cap clockwise to lock it properly
Make sure the lock is tight - insufficient closure can cause leaks

Maintenance of the gaskets

To maintain the sealing of the tank and preserve the gaskets:

Every 3 days: clean the tank with a neutral detergent, as mineral deposits can deform the gaskets
Every day: completely empty the tank and any residual water to avoid degrading the gaskets
Regularly inspect the tank to ensure there are no cracks or misaligned connections

If you observe persistent leaks despite proper locking, the gasket may be worn and need replacement.

Question 9

Why is water leaking from the water tank when using the misting fan?

Accepted Answer

If water is leaking from your AR5M39 misting fan, first check the following points:

Filling the tank

The tank must be filled with cold, clean, and previously boiled water only
Ensure that the tank is properly closed and locked after filling
Check that the tank cap/lid is not damaged or worn

Maintenance of the misting system

Empty any residual water from the misting fan daily to prevent buildup and leaks
Every 3 days, clean the tank with a neutral detergent and descale the nebulization plate with vinegar if necessary
A buildup of limescale can deform seals and cause leaks

Additional checks

Ensure that the device is in a stable and vertical position - tilting may cause water to leak
Check the integrity of the tank and connections - look for cracks or misaligned seals

If after these checks water continues to leak, the tank or its seals may be damaged and require replacement.

User manual ARDES Fan : user manuals and guides in PDF

Models ARDES Fan most viewed

Other categories ARDES

Recent questions about Fan ARDES