Question 1

Can the installation of the HUDSON 4B barbecue be done on a granite countertop?

Accepted Answer

According to the recommendations in the manual, the NATERIAL HUDSON 4B barbecue must be exclusively installed outdoors on a flat, well-ventilated surface.

Although the manual does not explicitly specify granite, this material can be used as an installation surface if it meets the following conditions:

Stability and level: The granite must be perfectly flat and able to support the weight of the barbecue without any issues (you can check the dimensions of your model in the manual)
Thermal resistance: Granite is naturally resistant to high temperatures, making it compatible with heat-generating appliances
Ventilation: Ensure that the outdoor installation allows for good air circulation, particularly under and around the barbecue
Safety distance: Maintain a minimum of 1 meter distance from any flammable surface (walls, structures, dry plants, etc.)
Additional protection: You can add a thermal insulating plate or a protective mat under the barbecue to protect the granite from potential damage due to moisture or extreme temperature variations

Important: The appliance must never be used or stored indoors, even if the granite countertop is covered or under a shelter.

Question 2

What size gas bottle should be used for the NATERIAL ALTON barbecue?

Accepted Answer

The NATERIAL ALTON barbecue is compatible with two types of gas bottles:

Butane (G30): 6 kg bottle recommended
Propane (G31): 5 kg bottle recommended

The barbecue has a power output of 9 kW (consumption of 654 g/h). For optimal use, you must use a regulator that complies with the EN16129 standard and a bottle stored vertically, outdoors, in a dry and ventilated place.

Warning: using an unsuitable or defective regulator is dangerous and voids the warranty.

Question 3

What size gas bottle to use for the NATERIAL KENTON 4B barbecue?

Accepted Answer

The NATERIAL KENTON 4B barbecue works with two types of gas bottles:

Butane (G30): 6 kg bottle - for summer use only
Propane (G31): 5 kg bottle - recommended for year-round use

Butane only offers optimal performance during the summer months. Below 10°C, performance decreases. If you use your barbecue in autumn, winter, or spring, propane is highly recommended for reliable and consistent use.

Your KENTON 4B has 4 stainless steel burners for a total power of 14 kW.

Question 4

The burner goes out when I release the button, how do I light it correctly?

Accepted Answer

This is normal operation for the NATERIAL KENTON 4B barbecue. The ignition button must be held and turned until you hear a click - this click indicates that the electronic ignition system has engaged correctly.

Correct ignition procedure:

Press the button of the desired burner
Turn it counterclockwise until you feel resistance
Wait 4 seconds
Continue turning until you hear a click - the burner will ignite

Once the click is heard, release the button - the burner should stay lit. If the flame goes out immediately after releasing, wait a few seconds and try again. If ignition does not occur within 5 seconds, turn off the gas, wait several minutes before trying again.

Always remember to open the lid before ignition and check that the gas bottle valve is fully open.

Question 5

How to light and start the NATERIAL KENTON 4B barbecue?

Accepted Answer

Procedure for lighting the NATERIAL KENTON 4B barbecue with electronic system:

Before you start: Always open the lid before lighting it. NEVER light the barbecue with the lid closed. Ensure that all buttons of the 4 burners are in the OFF position, then open the gas control valve on the bottle or regulator.

Lighting the burners: Push the button of the burner you want to light and turn it counterclockwise until you feel resistance. Wait 4 seconds, then continue turning the button until you hear a click. The burner should normally ignite at this point. You may need to repeat this operation several times before the burner ignites properly. Light the other burners in any order as needed, ensuring that each burner has ignited before lighting the next one.

If the electronic ignition does not work: Turn all buttons to the OFF position, completely close the gas valve on the bottle, wait at least 5 minutes, then repeat the entire procedure above. If the barbecue still does not light after this attempt, proceed to manual ignition.

Manual ignition (if the electronic system does not work): Insert a lit match through the ignition hole located at the bottom right of the control panel, and position it near the right burner opening. Then push and turn the right button counterclockwise to the maximum position. Once this burner is lit, turn on the remaining burners from right to left.

Preheating the barbecue: After lighting, leave all burners at the maximum position for 3 to 5 minutes. The lid must remain open during this preheating phase. This is an important step that must be performed before each cooking session. Once preheating is complete, reduce all burners to low heat to ensure the best cooking results.

Important safety: Never lean over the barbecue while lighting. Always wait a few seconds after turning the knob to allow gas to escape before bringing a source of ignition close.

Question 6

How to buy replacement burners for the NATERIAL KENTON 4B grill, specifically part number 10?

Accepted Answer

To purchase the replacement burners, part number 10, for your NATERIAL KENTON 4B grill, here are the steps to follow:

Contact NATERIAL customer service: The safest way to obtain original parts is to contact the manufacturer or official distributor directly. You can find their contact details on the official website or in the documentation provided with your device.
Check specialized retailers: Some stores specializing in barbecue equipment or spare parts may offer these burners. Inquire with local or online retailers.
Search on online sales platforms: Websites like Amazon, eBay, or other local platforms may offer compatible or original parts for your model.
Verify the exact reference: Make sure that part number 10 corresponds to the burner you need to avoid any mistakes when ordering.

By following these tips, you should be able to easily find and order the necessary burners for your KENTON 4B grill.

Question 7

How to light the burner of the NATERIAL HUDSON 3B barbecue?

Accepted Answer

To light the burner of your NATERIAL HUDSON 3B barbecue, follow these simple and safe steps:

1. Check the gas supply

Make sure the gas bottle is properly connected and contains enough gas.

2. Open the gas bottle valve

Turn the valve of the bottle counterclockwise to open it.

3. Prepare the burner knobs

Ensure that all burner knobs are in the off position before starting.

4. Light the burner

Turn the knob of the burner you wish to light to the on position.
Use a lighter or a long match to bring the flame close to the burner opening.
Hold the flame near the burner while turning the knob to allow ignition.

5. Adjust the flame

Once the burner is lit, adjust the flame intensity by turning the knob to achieve the desired power.

Important: Always handle gas with care and ensure that the barbecue is in a well-ventilated area before lighting.

User manual NATERIAL Barbecue : user manuals and guides in PDF

Models NATERIAL Barbecue most viewed

Other categories NATERIAL

Recent questions about Barbecue NATERIAL