Q: How to replace the blade of the EGO LM2020ESP?

Before you begin: Remove the safety key and disconnect the 56V battery. Wear thick gloves to protect yourself from the sharp blades. Replacement Procedure According to the manual of the EGO LM2020ESP, replacing the blade requires a 14 mm wrench: Remove the fan (upper part) Remove the inner collar underneath Disassemble the old blade Remove the outer collar Install the new blade in the correct position Reassemble all parts in reverse order Important: Ensure that the battery is properly removed and that the blades are completely stationary before any intervention. The manual emphasizes that rotating blades can cause serious injuries.

Question 1

How to replace the cutting head with a 3-tooth blade on the EGO BC3800E?

Accepted Answer

The EGO BC3800E can be equipped with two distinct cutting systems: a nylon line cutting head (38 cm wide) or a 3-tooth blade (30 cm wide, reference ABB1203). You can switch from one system to the other by following this procedure:

Replacement Steps

1. Preparation

Remove the battery before any intervention
Disassemble the spool housing by pressing on the tabs and pulling it outwards

2. Installing the 3-tooth blade

Remove the auxiliary protective cover (three screws and washers)
Take off the blade guard provided
Align the groove of the inner flange with the locking hole of the reducer
Insert the hex key as a stabilizer into the aligned holes
Mount the blade reference ABB1203 onto the spindle
Install the outer flange and the nut, then tighten following the direction indicated by the arrow on the flange

Safety: Wear sturdy protective gloves when handling the blade - its edges are very sharp. If you wish to reinstall the cutting head in the future, the auxiliary protective cover is mandatory to prevent excessive extension of the nylon line and motor overload.

Question 2

How to replace the blade of the EGO LM2020ESP?

Accepted Answer

Before you begin: Remove the safety key and disconnect the 56V battery. Wear thick gloves to protect yourself from the sharp blades.

Replacement Procedure

According to the manual of the EGO LM2020ESP, replacing the blade requires a 14 mm wrench:

Remove the fan (upper part)
Remove the inner collar underneath
Disassemble the old blade
Remove the outer collar
Install the new blade in the correct position
Reassemble all parts in reverse order

Important: Ensure that the battery is properly removed and that the blades are completely stationary before any intervention. The manual emphasizes that rotating blades can cause serious injuries.

Question 3

Which replacement blade model should be used for the EGO LM1900ESP mower?

Accepted Answer

For the EGO LM1900ESP mower, you must exclusively use the replacement blade model AB1901. The manual specifies that worn or damaged blades must be replaced with an identical blade - no other reference is compatible.

Installation and technical specifications

Tighten the blade with a torque of 49 to 59 Nm for optimal retention
Ensure that the blade is balanced to avoid excessive vibrations during cutting
Keep the blade sharp and clean for optimal performance and safe cutting

You can obtain the AB1901 blades from specialized gardening equipment retailers or on spare parts sales websites.

Question 4

Does the EGO Power+ LM1910E-SP mower have a mulching function?

Accepted Answer

Yes, the EGO Power+ LM1910E-SP mower has a mulching function. However, it is not included by default. As standard, the mower collects the grass cuttings in a 50-liter collection bag.

To use the mulching (finely chopping the grass discharged onto the lawn), you need to purchase a separate mulching kit compatible with this model. Once installed, this kit transforms the mower into mulching mode.

Question 5

How to correctly attach and position the grass collection bag on the EGO LM1702ESP mower?

Accepted Answer

To correctly attach and position the grass collection bag on your EGO LM1702ESP mower, follow these detailed steps:

Attaching the collection bag

Prepare the bag: Ensure that the bag is clean, in good condition, and ready to be installed.
Identify the attachment points: On the back of the mower, locate the hooks, clips, or bars designed to hold the bag.
Attach the bag: Place the bag onto these attachment points, ensuring that it is properly clicked in and secured. You should hear or feel a click indicating that the bag is securely attached.

Correct positioning of the bag

Check the alignment: The bag should hang straight, without twisting or folding, to allow optimal flow of the cut grass.
Activate the safety: If your model is equipped with a locking mechanism, ensure that it is engaged to prevent the bag from detaching during use.
Test the collection: Start the mower and observe if the grass is being properly sucked into the bag. If there are issues, check that the bag is securely attached and that no obstacles are blocking the flow of grass.

By following these tips, you will ensure effective use of the grass collection bag on your EGO LM1702ESP mower.

User manual EGO Lawn mower : user manuals and guides in PDF

Models EGO Lawn mower most viewed

Other categories EGO

Recent questions about Lawn mower EGO