JetStream T3700G-28TQ - Switch TP-LINK - Free user manual and instructions

Product Type	Managed Layer 3 (L3) Switch
Model	JetStream T3700G-28TQ
Brand	TP-Link
Dimensions (W x D x H)	440 x 260 x 44 mm (1U)
Weight	Approximately 4.5 kg
Power Supply	AC 100-240 V, 50/60 Hz, internal power supply
Ports	24 RJ45 10/100/1000 Mbps ports + 4 SFP+ 10 Gbps ports
Console Port	1 RJ45 console port for CLI management
Main Features	VLAN, QoS, link aggregation, security (ACL, 802.1X), static and dynamic routing (RIP, OSPF), management via Web, CLI, SNMP
Installation	On desktop (rubber feet) or in rack (brackets provided)
Maintenance and Cleaning	Unplug the device before cleaning. Use a soft, dry cloth. Do not use liquid or abrasive products.
Safety	Do not expose to water or moisture. Do not disassemble. All repairs should be carried out by qualified personnel.
Spare Parts and Repairability	Contact TP-Link technical support for spare parts and repair. Opening the casing voids the warranty.
Warranty	TP-Link limited warranty, duration indicated on packaging (typically 3 years)
Default IP Address	http://192.168.0.1
Default Credentials	Username: admin, Password: admin (all lowercase)
Operating Temperature	0 °C to 40 °C
Operating Humidity	10% to 90% RH non-condensing
Certifications	CE, FCC, RoHS

Frequently Asked Questions - JetStream T3700G-28TQ TP-LINK

How to install the switch on a desktop?

Place the switch on a flat and sturdy surface. Remove the protective films from the provided rubber feet, then attach them to the four corners of the bottom of the device.

How to mount the switch in a rack?

Attach the mounting brackets to each side of the switch using the provided screws. Then use suitable bolts (not included) to secure the switch to the rack. Ensure the rack is stable and grounded.

How to connect an SFP module?

Insert the SFP module into the slot until it clicks into place. To remove it, gently pull on the tab or lever. Use modules compatible with 10 Gbps standards.

How to access the web management interface?

Connect your computer to the switch via an Ethernet cable. Configure your computer with an IP address in the 192.168.0.x subnet (e.g., 192.168.0.2, subnet mask 255.255.255.0). Open a browser and enter http://192.168.0.1. Enter admin as the username and password.

What is the default password of the switch?

The default username and password are both admin (lowercase). For security reasons, it is recommended to change them upon first login.

How to reset the switch to factory defaults?

Press and hold the Reset button (located on the front or rear panel) for about 10 seconds until the LEDs flash. Release the button. The device will reboot with factory settings.

Does the switch support static and dynamic routing?

Yes, the T3700G-28TQ is a Layer 3 switch that supports static routing, as well as dynamic protocols RIP and OSPF.

Can I use standard RJ45 cables for the 10 Gbps ports?

The RJ45 ports support 10/100/1000 Mbps. The 10 Gbps ports are the SFP+ ports which require SFP+ modules or appropriate DAC (Direct Attach Copper) cables.

What to do if the switch does not power on?

Check that the power cable is properly connected to the device and a working power outlet. Test with another cable or outlet. If the problem persists, contact TP-Link support.

How to clean the switch?

Unplug the device before cleaning. Use a soft, dry cloth to wipe the casing. Do not use liquid products, sprays, or abrasive cloths.

USER MANUAL JetStream T3700G-28TQ TP-LINK

Easy Smart&Smart&Managed Rackmount Switch

CONTENTS

Deutsch....01

English....06

Español....11

Ελληνικά....16

Français....21

Italiano....26

Português....31

Suomi....36

Nederlands....41

Svenska....46

Norsk....51

Dansk....56

Türkçe....61

Installation

- Tischmontage

- SFP-Port

- Einschalten

Konfiguration

- Desktop Installation

To install the device on the desktop, please follow the steps below:

1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings.
2. Remove the adhesive backing papers from the rubber feet.
3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.

- Rack Installation

To install the device in a rack, follow the instructions described below:

1. Check the grounding and stability of the rack.
2. Secure the supplied rack-mounting brackets to each side of the device with supplied screws.

1. After the brackets are attached to the device, use suitable screws (not provided) to secure the brackets to the rack.

Connection

- Ethernet Port

Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shown.

- SFP Port

For switches with SFP ports, you can connect a SFP port to a SFP module. If an SFP transceiver is installed in a slot and has a valid link on the port, the associated RJ45 port will be disabled and cannot be used.

- Console Port

For switches with the console port, you can connect the console port with your computer by the console cable. Then you can load the CLI to manage the switch.

- Power On

Plug the female connector of the provided power cord into the power socket of the device, and the male connector into a power outlet.

Configuration

- Configure the Switch Using the GUI

1. Set the IP address of your PC in the same subnet of the switch. The IP address is 192.168.0.x("x" is any number from 2 to 254); the Subnet Mask is 255.255.255.0.
2. Open a web browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key.
3. Enter admin for the default User Name and Password, both in lower case letters. Then click the Login button or press the Enter key.
4. After a successful login, you can configure the switch on the management page.

- Configure the Switch Using the CLI (Only for Smart Switches and Managed Switches)

You can log on to the switch and access the CLI to manage the switch. For the detailed instructions as to how to do this, please refer to the CLI Guide.

- Configure the Switch Using the Utility (Only for Easy Smart Switches)

You can use the Easy Smart Configuration Utility to centrally manage entire networks of the Easy Smart Switches. For the detailed instructions as to how to do this, please refer to the Utility User Guide.

Instalación

- Puerto SFP

- Encender

Configuración

- Θúpa Console

- Ενεργοποιήστε

Ρύθμιση

Configuration

- Configurer le switch via son interface graphique

- Accensione

Configurazione

- Configure lo Switch usando la GUI

- Ligar

Configuração

- Configurar o Switch via Interface gráfica

- Virta päällä

Konfigurointi

- Konfiguroi kytkin GUI:lla

- Inschakelen

Configuratie

- Desktop-installation

- Ström på

Konfiguration

- For å slå på

Konfigurasjon

- Tændt

Konfiguration

- Cihazı Çalıştırma

Yapılandırma

• When a product has a power on/off button, the power on/off button is one way to turn-off the product. For products without the on/off button, the only way to completely turn-off the product is to disconnect the product or the power adapter from the power source. The disconnected device shall remain readily operable.
• Do not open this product or attempt to service it; it may expose you to dangerous high voltage or other risks. Opening a sealed component or sealed product/s will void the warranty. For product servicing, please contact us.
• Do not operate this product near water.

TP-LINK Limited Product Warranty

For TP-LINK Branded Products Only.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE).

TO THE EXTENT ALLOWED BY LOCAL LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS.

TP-LINK warrants the TP-LINK branded hardware product contained in the original packaging against defects in materials and workmanship when used normally in according with TP-LINK's guidelines for some period which depends on the local service from the date of original retail purchase by the end-user purchaser.

Español

South Building(floors 1,3,4,5) and 28(floors 1-4), Central Science & Technology Park, Shennan Rd, Nanshan, Shenzhen, China

Robert-Bosch-Straße 9, 65719 Hofheim am Taunus, Germany

Unit 2 & 3 Riverview (142-144), Cardiff Road, Reading, RG1 8EW

Marathonodromou 77, Marousi 151 24, Greece

Specifications are subject to change without notice. TP-LINK is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.