TK 2020 - Water heater ECG - Free user manual and instructions

Product Type	Water Heater
Brand	ECG
Model	TK 2020
Capacity	80 L
Power Rating	2000 W
Voltage	230 V ~ 50 Hz
Energy Efficiency Class	C
Temperature Range	30 °C to 75 °C
Heating Time (full tank)	Approx. 2 hours 30 minutes
Dimensions (H x W x D)	800 x 500 x 500 mm
Weight (empty)	25 kg
Material	Enameled steel tank
Protection Class	IPX4
Control Type	Thermostat with dial
Safety Device	Temperature and pressure relief valve
Installation	Wall-mounted, vertical
Water Connection	1/2" BSP female
Standby Heat Loss	0.8 kWh/24h
Maintenance	Annual inspection by qualified technician
Replaceable Parts	Thermostat, heating element, anode rod
Warranty	2 years
Manual Languages	EN, CS, DE, HU, PL, SK, SL

Frequently Asked Questions - TK 2020 ECG

What is the recommended temperature setting for optimal efficiency?

For optimal efficiency and safety, set the thermostat to 60 °C. This prevents bacterial growth while minimizing heat loss.

How often should I replace the anode rod?

Check the anode rod annually and replace it every 2-3 years or if heavily corroded to prevent tank rust.

Can I install the water heater myself?

Installation must be carried out by a qualified professional to ensure compliance with local plumbing and electrical codes.

What does the safety relief valve do?

The temperature and pressure relief valve automatically releases water if the temperature or pressure exceeds safe levels, preventing tank rupture.

How do I drain the water heater?

Turn off power and water supply, attach a hose to the drain valve, open the valve and a hot water tap to allow air in, and drain completely. Refer to manual for details.

My water heater is not heating properly. What could be wrong?

Possible causes: tripped circuit breaker, faulty thermostat, or burned-out heating element. Check power and consult a technician.

Is the ECG TK 2020 suitable for hard water?

It is compatible, but in hard water areas, periodic descaling is recommended to maintain efficiency.

What is the standby power consumption?

Standby heat loss is approximately 0.8 kWh per 24 hours, depending on ambient temperature and insulation.

Can I use an extension cord?

No, the water heater must be directly connected to a dedicated circuit. Extension cords may overheat and cause fire.

Where can I find replacement parts?

Authorized service centers or online stores carrying ECG parts. Use only genuine parts for safety.

USER MANUAL TK 2020 ECG

White ECG electric heater with heat exchanger and control panel (no visible text or symbols)

TK 2020

KONVEKTOR

NÁVOD K OBSLUZE

KONVEKTOR

NÁVOD NA OBSLUHU

GRZEJNIK KONWEKTOROWY

INSTRUKCJA OBSŁUGI

HÓSUGÁRZÓ

HASZNÁLATI ÚTMUTATÓ

KONVEKTIONSHEIZUNG

BEDIENUNGSANLEITUNG

CONVECTION HEATER

INSTRUCTION MANUAL

KONVEKCIJSKA GRIJALICA

UPUTE ZA UPORABU

KONVEKCIJSKI GRELNIK

NAVODILA

KONVEKTORSKA GREJALICA

UPUSTVO ZA UPOTREBU

CZ

SK

PL

HU

DE

GB

HR/BIH

SI

SR/MNE

CZ

1. Hot air vent
2. Heat element switches with indicator
3. Temperature control
4. Air inlet

HR/BIH

1. Otvor za topli zrak
2. Prekidači grijaćeg elementa s indikatorom
3. Kontrola temperature
4. Ulaz zraka

SI

Do not immerse in water! – Neponořovat do vody!

SESTAVENÍ KONVEKTORU

Diagram of a mechanical clamp or clamping device with a screwdriver inserted, showing no text or symbols.

Diagram of a tool interacting with a mechanical component, showing a screwdriver and a grid-like structure (no text or symbols)

Diagram of a tool interacting with a mechanical component, showing a screwdriver and a striped panel (no text or symbols)

Diagram of a mechanical clamp or lever mechanism with a screwdriver inserted, showing no text or symbols.

Read carefully and save for future use!

Warning: The safety measures and instructions, contained in this manual, do not include all conditions and situations possible. The user must understand that common sense, caution and care are factors that cannot be integrated into any product. Therefore, these factors shall be ensured by the user/s using and operating this appliance. We are not liable for damages caused during shipping, by incorrect use, voltage fluctuation or the modification or adjustment of any part of the appliance.

To protect against a risk of fire or electric shock, basic precautions shall be taken while using electrical appliances, including the following:

1. Make sure the voltage in your outlet corresponds to the voltage provided on the appliance label and that the socket is properly grounded. The outlet must be installed according to valid safety instructions.

2. Do not operate the heat convector without the base properly attached.

3. Do not operate the device with a damaged cord. All repairs including cord replacements shall be performed by a professional service centre! Do not remove protective covers of the appliance, risk of electric shock!

4. Protect the device against direct contact with water and other liquids, to prevent potential electric shock.

5. Do not operate the convector outdoors or in a moist environment and do not touch the cord or appliance with wet hands. Risk of electric shock.

6. Close supervision is necessary for operating the heat convector near children!

7. Make sure the convector is placed on a flat surface.

8. Do not use the convector near infl ammable items or underneath them, for example, near curtains. The temperature of surfaces near the heat convector (0.5 m) can be hotter than usual. Place the convector to ensure sufficient air circulation.

9. Do not place the convector on a carpet with high bristles.

10. Do not place the convector in front of or directly under an electric socket.

11. Do not cover the heat convector! Risk of overheating or catching fire if covered.

12. The convector must not be plugged into the socket through a timer switch or connected to a remotely switched supply fire in case of a remotely activated covered or insufficiently placed convector.

13. Do not use the convector in the direct vicinity of the bath, shower or pool and do not use in places from which it may fall into the bath or other water containers!

14. If an unusual smell or smoke begins to come from the device, disconnect the device and have it checked by a service centre.

15. Do not switch off the device by pulling on the power cord. Always turn off the main switch of the convector first!

16. Always unplug the convector when moving it to another location.

17. Do not leave a convector with inserted power cord unsupervised. Disconnect the cord from the electrical outlet prior to performing maintenance. Do not unplug the device by pulling the power cord. Unplug the cord from the outlet by grasping the plug.

18. Do not allow the cord to touch hot surfaces or lead the cord over sharp edges.

19. Do not use the convector in places where infl ammable materials are stored (paint, gasoline, solvent etc.) or where there is a risk of infl ammable fumes appearing.

20. Do not put your fingers or other objects into the openings of the heat convector.

21. Use the convector only in accordance with the instructions given in this manual. The manufacturer is not liable for damages caused by the improper use.

22. The appliance may be used by children 8 years or older and by persons with reduced physical or mental capabilities, if they are under supervision or if they have been instructed in the use of the appliance in a safe manner and understand the potential risks. Children must not play with the appliance. Children must not carry our cleaning and maintenance of the appliance, unless they are 8 years or older and under supervision. Children younger than 8 years have to be kept away from the appliance and its power supply.

circuit, of less than 3 years should be kept away unless continuously supervised.

- Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and

less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

Do not immerse in water!

CONVECTOR ASSEMBLY

Make sure the package contains all parts necessary for assembling the convector. Contact your vendor if this is not the case.

Package contents:

1. Heat convector: 1 piece
2. Base: 2 pieces
3. Attachment screws: 4 pieces
4. Operating manual: 1 piece

Unplug the device, prior to any form of manipulation, to prevent injury by electric shock.

The base must be firmly attached to the convector before use (included in the package containing the convector). The base legs are attached to the convector base using four screws included in the package. Make sure they are properly inserted into the rails on the bottom of the convector.

WARNING: Under no circumstances should you operate the heater standing without the base attached.

Diagram of a screwdriver inserted into a clamped tool with a grid-patterned handle (no text or symbols)

GB

REQUIREMENTS ON INSTALLATION

• Place the convector on a flat surface with a sufficient amount of space around the appliance to ensure the proper function of exhaust vents.
• The distance between the device and surrounding objects must be at least 50 cm.

WARNING:

To prevent the device from overheating, do not cover the heater. The heater must not be placed directly under an outlet.

INSTRUCTIONS

This convector uses hot air technology with temperature regulation via thermostat.

The power level can be set via heat element switches:

Switch 1 = power of 750 W

Switch 2 = power of 1250 W

Switch 1+2 = power of 2000 W

Activating the convector and temperature control

1. With respect to the above defined safety instructions, select a proper location to place the convector.
2. Plug the power cable into a proper electric socket.
3. Turn the THERMOSTAT CONTROL completely to the right for maximum power.
4. Activate the heat elements via the SWITCHES on the side panel. The activation of heat elements is indicated by switch indicator lamps. Activate both switches to achieve maximum heat power.
5. When the required temperature is achieved in the room, turn the thermostat controller slowly to the left until you hear the thermostat click and the lamps on the heat element switches go off. The convector will now maintain the temperature in the room at the value set by automatically switching the heat elements on and off.

Note: An odour or smoke may emit from the heat elements during the first use of the appliance or when turning on after a longer period of time. This effect is normal and will go away after a short while.

Turning off the convector

• First switch off the convector and set the thermostat controller to "MIN", then unplug the power cord from the socket!
• The device shall only be handled when turned off via the switches and disconnected from the network outlet.

Protection against overheating

• The internal heat fuse protects the heater against overheating and switches off the appliance automatically. In this case, the operating lamp will switch off.
• If the appliance switches itself off, unplug the power cable from the socket. After cooling down (about 15 minutes), the appliance is again ready for use. Plug the power cable back into the socket.
• If the situation persists, first make sure the thermostat controller is properly configured and whether the air vents are not covered.

CLEANING

• Prior to cleaning, unplug the convector and leave the appliance to completely cool down.
• Clean the outer surface with a moist cloth and wipe dry using a towel. Do not use detergents or abrasive cleaning agents and prevent water from entering the appliance.

STORAGE

If you do not plan to use the appliance for a longer period of time, it should be placed in a clean and dry location protected against dust.

DO NOT COVER!

TECHNICAL SPECIFICATIONS

Max. input power 2000 W

3 heat settings 750 / 1250 / 2000 W

Nominal voltage: 230 V\~50 Hz

Nominal input power: 2000 W

Noise level: <55 dB

USE AND DISPOSAL OF WASTE

Wrapping paper and corrugated paperboard – deliver to scrapyard. Packing foil, PE bags, plastic elements – throw into plastic recycling containers.

DISPOSAL OF PRODUCTS AT THE END OF LIFETIME

Disposal of electric and electronic equipment (valid in EU member countries and other Europe countries with an implemented recycling system)

The represented symbol on the product or package means the product shall not be treated as domestic waste. Hand over the product to the specified location for recycling electric and electronic equipment. Prevent negative impacts on human health and the environment by properly recycling your product.

Recycling contributes to preserving natural resources. For more information on the recycling of this product, refer to your local authority, domestic waste processing organization or store, where you purchased the product.

This product complies with EU directive requirements on electromagnetic compatibility and electrical safety.

The instruction manual is available at website www.ecg-electro.eu.

Changes in text and technical parameters reserved.

and other Europ

08/05

SIGURNOSNE UPUTE

Diagram of a screwdriver inserted into a clamped tool with a striped cover (no text or symbols)

Technical line drawing of a screwdriver holding a flat blade (no text or symbols)

SI

Diagram of a screwdriver holding a rack with a slide, no text or symbols present

PAŽNJA: Grejalicu ni u kom slučaju nemojte koristiti kao samostojeću, bez pričvršćenih nogara.

SR/MNE

ZAHTEVI ZA INSTALACIJU

PEČAT I POTPIS PRODAVATELJA

PROIZVAJALEC ali DAJALEC GARANCIJE:

K+B Progres, a.s.; MBS: 61860123