RVF 7 - Robot vacuum Kärcher - Free user manual and instructions

USER MANUAL RVF 7 Kärcher

Exterior view of a modern KRONER brand water dispenser device (no visible text or symbols on body)

3D rendering of a robotic vacuum cleaner with three legs and a circular head (no text or symbols visible)

Deutsch 9

English 22

Français 34

Italiano 48

Español 61

Português 75

Nederlands 88

Türkçe 100

Svenska 113

Suomi 125

Norsk 137

Dansk 148

Eesti 160

Latviešu 172

Lietuviškai 184

Polski 197

Magyar 210

Čeština 223

Slovenčina 235

Slovenščina 248

Română 260

Hrvatski 273

Srpski 286

Ελληνικά 298

Русский 312

Українська 327

Қазақша 341

Български 355

العربيه 371

A

Labeled diagram of a device interior with numbered components for identification

Transparent plastic container with a black horizontal stripe and a circled number 5 on the side (no text or symbols on the object itself)

3D rendered mechanical component with no visible text or symbols

Yellow cylindrical object with numbered label (2) and circled number (10), no visible text or symbols beyond labels

Technical diagram of a boat's internal components with numbered labels pointing to parts 1 and 12.

Front view of a white robotic vacuum cleaner with a digital display and circular badge (no text or symbols visible)

26 25 12

Close-up of a black plastic brush head with serrated texture and a circled number 5 on the tip (no text or symbols on the object itself)

15 14 13

KRONCHER 23 24 22 20 21 19

RM 536 Foam Stop 17 18 16

B 30 29 28 30 31 32 33 34 37 38 35 36 39 37 38 43 44 45 42 41 40 ① 水印 水印

White electronic device with a cable inserted into its side panel, showing a black arrow indicating the insertion point (no text or symbols visible)

Diagram of a helicopter's fuselage with two propellers above it, showing structural components (no text or symbols)

3D model of a robotic vacuum cleaner with an arrow pointing to its internal component, labeled 'CLICK' (no text or symbols on the diagram itself)

G a b

3D rendering of a circular robotic device with a curved arrow indicating motion or change, shown with an inset U-shaped diagram (no text or symbols)

Close-up of a robotic vacuum cleaner with a magnified inset showing internal components (no text or symbols visible)

J a b

Close-up of a robotic vacuum cleaner with a close-up inset showing the component detail (no text or symbols visible)

L a b c d 1 x

M a b

N a b c d 1x

3D rendering of a robotic vacuum cleaner with a yellow circular button labeled 'I' pointing to the component (no text or symbols on the device itself)

P a b

Two views of a small boat showing internal components, labeled 'a' and 'b', with no visible text or symbols beyond labels.

Technical illustration of a mechanical assembly with labeled parts (a and b), showing internal components and mounting base (no text or symbols beyond labels)

Top-down view of a circular device with yellow plastic components and black propellers (no text or symbols visible)

3D rendering of a car interior with yellow plastic components and black outlines (no text or symbols)

a b c

V a b c

W a b c

3D rendering of a robotic vacuum cleaner with highlighted interior (no text or symbols)

Two views of a robotic vacuum cleaner with a close-up inset showing internal components (no text or symbols visible)

Z a b

AA 60°

Illustration of a hand tool interacting with a device, showing mechanical components and fluid flow (no text or symbols)

3D rendered image of a gray industrial machine component with no visible text or symbols

a b c

Diagram of a pipette pressing into a grating with a hand holding the tip (no text or symbols)

Interior view of a robotic vacuum cleaner with labeled parts (a and b), showing internal components and wiring (no text or symbols beyond labels)

3D rendering of a robotic vacuum cleaner with yellow insulation and black screw-like components, shown from two different angles (no text or symbols)

b(d) a) c

AI

3D rendering of a white electronic device with a close-up inset showing its internal components (no text or symbols visible)

Inhalt

⑰ Foam Stop 30 ml (2 x)

⑱ RM 536 500 ml

⑲Ein-/ Aus-/ Pause-Taste

20 Home-Taste

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

General notes.... 22
Safety instructions 22
Symbols on the device 23
Environmental protection.... 23
Intended use.... 23
Accessories and spare parts 23
Scope of delivery 23
Device description 23
Buttons on the charging station 24
Initial start-up 26
Startup 26
Operation.... 27
Transport 30
Storage 30
Care and service 30
Troubleshooting guide 32
Warranty 34
EU Declaration of Conformity 34
Technical data 34

General notes

Read the original instructions before using the device for the first time and act in accordance with it. Keep this document

for future reference or for future owners.

• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.
• Notify the dealer immediately in the case of shipping damage.
• Check the package contents when unpacking for missing accessories or for damage.

Safety instructions

- In addition to the information in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.

- Warnings and information notices attached to the device provide important information for hazard-free operation.

Hazard levels

⚠️DANGER

- Indication of an imminent threat of danger that will lead to severe injuries or even death.

⚠ WARNING

- Indication of a potentially dangerous situation that may lead to severe injuries or even death.

△CAUTION

- Indication of a potentially dangerous situation that may lead to minor injuries.

ATTENTION

- Indication of a potentially dangerous situation that may lead to damage to property.

General safety instructions

The laser radar of the device complies with IEC 60825-1:2014 for Class 1 laser product safety and does not produce laser radiation that is hazardous to the human body.

⚠️ DANGER ● Risk of asphyxiation. Keep packaging film out of the reach of children.

⚠ WARNING • Only use the device for its proper use. Take into account the local conditions and beware of third parties, in particular children, when working with the device. • The device is not intended for use by persons with restricted physical, sensory or mental abilities or those lacking in experience and / or lacking in knowledge. • Only people who have been instructed on how to use the device, or have proven their ability to operate it, and have been explicitly instructed to use it, must use the device. • Children must not operate the device. • Children must be supervised to prevent them from playing with the appliance. • Children may only perform cleaning work and user maintenance under supervision. • Children from the minimum age of 8 may only use the device if they are properly supervised, have been instructed in its use by a person responsible for their safety, and if they have understood the resultant dangers involved.

⚠️ CAUTION • Risk of accidents and injuries.

Take into account the weight of the device for transportation and storage. See chapter Technical data in the operating instructions. ● Safety devices are provided for your own protection. Never modify or bypass safety devices.

ATTENTION • Damage to the device. Do not stand on the device or place children, objects or pets on it. • The device contains batteries that can only be replaced by qualified staff.

Risk of electric shock

⚠ WARNING • The appliance contains electrical components - do not clean the appliance under running water. • Switch off the device before all care and maintenance work.
⚠️ CAUTION • Have repair work and work on electrical components carried out by the authorised customer service only.

Safety instructions for operation

⚠️ DANGER • Do not operate the device in rooms with a burning fire or embers in an open fireplace without supervision. • Do not operate the device in rooms with burning candles without supervision.

⚠ WARNING • Short circuit hazard. Keep conductive objects (e.g. screwdrivers or similar tools) away from the charging contacts.

⚠ CAUTION • Be aware of the risk of tripping due to the cleaning robot moving around. • Risk of injury. Never touch the cleaning roller of the device with fingers or tools during operation. • Do not stand or sit on the station or the cleaning robot. • Be aware that objects can fall over if the cleaning robot bumps into them (also objects on tables or small pieces of furniture). • Note that the cleaning robot can get caught in hanging telephone cables, electric cables, tablecloths, cords, belts, etc. This can cause objects to fall.

ATTENTION • Do not operate the device in rooms that are secured with an alarm system or motion sensor. • Operate the device only at temperatures from 0^ C to +35^ C. • Only use the device indoors. • Do not pick up sharp or larger objects with the device, such as e.g. glass shards, gravel or toy parts. • Pick up all cables from the floor before using the device to prevent it from dragging them when cleaning. • Cordon off all areas where there is a risk of the device falling down. E.g. stairways or galleries without barriers.

Safety instructions for charging station

⚠️ DANGER • Only connect the device to an AC power source. The voltage indicated on the type plate must match the mains voltage of the power source.

- For safety reasons we recommend operating the device only via a fault current protection switch (maximum 30mA ). - Never touch the mains plug and socket with wet hands. - Danger of explosion. Do not charge any non-rechargeable battery.

⚠ WARNING • Only connect the device to an electrical connection which has been set up by a qualified electrician as per IEC 60364-1. • Check that the mains voltage corresponds with the voltage stated on the type plate of the charger. • The appliance contains electrical components - do not clean the appliance under running water. • Short circuit hazard. Keep conductive objects (e.g. screwdrivers or similar tools) away from the charging contacts. • Short circuit hazard. Only clean the charging contacts of the charging station dry. • Always pull out the mains plug before all care and maintenance work. • The1.269-690.0 cleaning robot may only be charged on the charger of a charging station with the part number 4.269-091.0. • Only charge the supplied cleaning machine in the charging station. • Check the mains cable for damage each time before every operation. Do not use a damaged mains cable. If damaged, replace the mains cable with an approved replacement. You can get a suitable replacement from KÄRCHER or one of our service partners.

ATTENTION • Use the charging station indoors only. • Do not place the charging station near heat sources, e.g. heaters. • Store the charging station indoors only, in a cool, dry place. • Recharge the cleaning robot at least every 5 months to prevent the battery from deep discharging. • Switch off the charging station before all care and maintenance work.

Symbols on the device

Read the operating instructions and all safety instructions before operating the device for the first time.

Protect the device from moisture. Store the device in a dry place. Do not subject the device to rain. The device is only suitable for indoor use.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can a potential danger to human health and the envient. However, these components are required for correct operation of the device. Devices marked by symbol are not allowed to be disposed of together the household rubbish.

Notes on the content materials (REACH)

Current information on content materials can be found at: www.kaercher.de/REACH

Intended use

The device consists of two units, a charging station and a battery-powered cleaning robot.

• This cleaning robot is designed for fully automatic wet and dry cleaning.
• No water-sensitive floor coverings such as untreated cork floors, since the moisture can penetrate and damage the floor.
• The device is suitable for cleaning carpets, PVC, linoleum, tiles, stone, oiled and waxed parquet, laminate and all water-resistant floor coverings.
• This device has been developed for use in private households and is not intended for the load imposed by commercial use.

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Device description

For the illustrations, refer to the graphics page.

Illustration A

Illustration B

① Waste water tank
② Cleaning roller (2 x)
③ Suction shaft on the cleaning robot
④ Drive wheel
⑤ Brush cover

⑥ Cleaning brush
7 Side brushes
⑧ Steering roller
⑨ Fall sensor
⑩ Roller cassette
⑪ Opening lever of waste water tank
⑫ Waste water suction valve on the device
⑬ Fresh water tank
⑭ Rubber seal for fresh water supply
⑮ Cleaning tool
⑯ Dust container
⑰ Foam Stop 30 ml (2 x)
⑱ Detergent 536 500 ml
⑲ On/Off/Pause button
20 Home button
213D sensor with camera
②2 Wall tracking sensor
②3 LED bar for status display
24 Top cover
⑳Fresh water supply
26 Contacts for charging station
⑳ Laser sensor (LiDAR)
28 Loading ramp
⑲Storage compartment for roller
③0 Charging station cover
③1 Carrying handle
③2 Charging socket
33 Cable clips
③4 Cable guide
35 Dust bag
36 Mains cable
③7 Waste water tank
38 Fresh water tank
39 Dust bag intake
④0 "Start self-cleaning" button
④1 "Change cleaning mode" button
④2 "Start cleaning" button
④3 Fresh water filler valve
④4 Suction valve for waste water tank
45 Suction shaft on the charging station

Buttons on the charging station

Note

The buttons on the charging station can only be pressed when the cleaning robot is in the charging station, as this is the only way to ensure contact with the device.

Button Description
	The button is used to start cleaning.
	The button is used to select the cleaning modes.If the symbol lights up, wet and dry cleaning mode is activated.If the symbol does not light up, only dry cleaning mode is activated.
	The button is used to activate the self-cleaning function. This includes:Emptying the waste water tankFilling the fresh water tankCleaning the rollerDrying the rollerEmptying the dust bag

Function of the cleaning robot

• The mobile cleaning robot draws its energy from a built-in rechargeable battery, which it regularly re-charges at the charging station provided. If the battery charge is too low, it automatically returns to the charging station to recharge and, if necessary, pauses the current cleaning task.
• Once charging is complete, the cleaning robot automatically leaves the charging station and resumes cleaning if a task was interrupted. The cleaning robot also returns to the charging station when it has finished cleaning.
• The cleaning robot communicates status messages via a voice output and various LED colours on the device.
• The cleaning robot moves systematically. It scans the room with a laser sensor (LiDAR) and then cleans the room step-by-step. It avoids obstacles that are at least as tall as the built-in laser sensor (LiDAR).
• The cleaning robot has fall sensors that can detect staircases and steps, designed to prevent it from falling.
• The ultrasound sensor is used for carpet detection, which can be activated and deactivated individually in the app. Depending on the configuration, the cleaning robot avoids carpets.
• The cleaning robot has a fresh and waste water tank as well as a microfibre roller, a dust container, a cleaning brush and 2 side brushes. These components make it possible to clean dry and wet at the same time. The suction process collects all dust particles and coarse dirt in the dust container so that no dust particles and coarse dirt are picked up during wet cleaning and collect in the waste water tank.
• In the multifunctional charging station, the waste water is automatically extracted from the device af-

ter each cleaning process, fresh water is added and dust is removed from the dust container. It is also possible to clean, dry and store the cleaning rollers in the charging station.

Suction can only take place under the following conditions:

• The cleaning robot is in the charging station.
• A dust bag is suspended in the charging station.
  • The suspended dust bag is not full.
  • The charging station cover is closed.

LED colours on the device

LED buttons LED bar Meaning
off off The device is switched off.		The device is in sleep mode.The device is in "Do not disturb" mode.
pulsate white pulsates white The device is switched on.		The new firmware is downloaded and updated.
pulsate blue off The network connection is being es-		tablished.
lights up green lights up blue or yellow (depending on the selected cleaning mode)		The network connection has been successfully completed.
flash blue off The network connection is reset.
pulsate green off The device is in the charging station		and the battery is being charged.
pulses or flashes red pulses or flashes	red A malfunction has occurred. Troub-shooting see Troubleshooting guide.

LED colours on the charging station

LED buttons LED bar Meaning
off lights up white The charging station	is in standby	mode.
"Start cleaning" button:pulses green"Change cleaning mode" button-lights up blue/off"Start self-cleaning" buttonlights up white	flashes green The device is in the charging station and the battery is being charged.
"Start cleaning" button:off"Change cleaning mode" button-lights up blue/off"Start self-cleaning" button:pulses yellow	pulses yellow The contents of the dust container in the device are extracted by the charging station.
"Start cleaning" button:off"Change cleaning mode" button-lights up blue/off"Start self-cleaning" button:pulses blue	pulses blue The device is in the charging station and the cleaning rollers are being cleaned.
"Start cleaning" button:lights up red"Change cleaning mode" button:lights up red"Start self-cleaning" button:lights up red	pulses or flashes red A malfunction has occurred. Troubleshooting see Troubleshooting guide.
off off The device is switched off.		The device is in "Do not disturb" mode.

Special modes

Sleep mode

The cleaning robot automatically switches to sleep mode after 5 minutes of inactivity. Press any button to wake it up.

- The cleaning robot does not switch to sleep mode when it is on the charging station.

- The cleaning robot switches off automatically if it is in sleep mode for more than 6 hours

"Do not disturb" mode

It is possible to activate the "Do not disturb" mode. In "Do not disturb" mode, the cleaning robot does not emit any acoustic warnings. The LED buttons and LED bar are switched off.

"Do not disturb" mode can be activated in the App. Downloading the App is described in the chapter Connecting cleaning robots with WLAN and App.

Note

In "Do not disturb" mode, the cleaning robot is not switched off. To continue cleaning, briefly press On/Off/Pause button.

Remote control

In the app, there is the option to navigate the robot if it gets stuck in an inaccessible place, for example. This remote control can be selected in the app under "Settings" > "Robot settings".

Initial start-up

Setting up the charging station

- Select the location so that the cleaning robot can easily reach the charging station.

ATTENTION

Risk of damaging the floor due to moisture

The wet roller can damage the floor during charging. Position the charging station on a water-resistant floor and on the floor protection plate supplied.

• Ensure a distance of at least 0.5 m to the left and right of the charging station and a distance of at least 1.5 m in front of the charging station.

• The location must not be exposed to direct sunlight.

• Set up the charging station.

Illustration C

1. Plug the device plug of the power cable into the charging socket on the charging station.

Illustration D

1. Connect the mains plug.

Connecting the cleaning robot with the charging station

1. Place the cleaning robot manually on the charging station and make sure that the battery terminals have a good contact.
   The cleaning robot switches on automatically. The LED buttons and the LED bar light up.

Note

During the initial start-up, manual switch-on without contact to the charging station is not possible. After the initial start-up, the cleaning robot automatically moves to the charging station.

Connecting cleaning robots with WLAN and App

The cleaning robot can be operated directly via buttons on the device or via an App using a WLAN-enabled mobile device. To be able to use all available functions we recommended controlling the cleaning robot via the KÄRCHER Indoor Robots App.

Before you download the app, make sure you have the following:

• The mobile device is connected to the Internet.
- The 2.4 GHz or 5 GHz WLAN of the router is activated.
- Sufficient WLAN coverage is guaranteed. Download the KÄRCHER Indoor Robots App from the Apple App Store® or from the Google Play™ store.

GET IT ON Google Play

Download on the App Store

• Google Play™ and Android™ are trademarks or registered trademarks of Google Inc.
• Apple ^® and App Store ^® are trademarks or registered trademarks of Apple Inc.

Connecting cleaning robots with WLAN and KÄRCHER Indoor Robots App:

1. Download the KÄRCHER Indoor Robots App from the Apple App Store or from the Google Play Store.
2. Open the KÄRCHER Indoor Robots App.
3. Create an account (if you are not already registered).
4. Add the desired cleaning robot.
5. Follow the step-by-step instructions in the App.

Startup

Installing the side brush

1. Turn the cleaning robot upside down.

2. Fit the side brushes.

Illustration E

Fitting the waste water tank

1. Push the waste water tank horizontally into the device until it audibly latches into place. Illustration F

Remove waste water tank

1. Press the waste water tank unlocking button and remove the waste water tank from the device. Illustration G

Inserting the cleaning roller

1. Remove the magnetic cover on the roller cassette. Illustration H
2. Press the unlocking button on the roller cassette. Illustration I
   The roller cassette detaches from the cleaning robot.
3. Remove the roller cassette from the cleaning robot.
4. Fit the cleaning roller onto the roller holder. Illustration J

5. Pay attention to the cassette guide and push the roller cassette into the cleaning robot until it audibly engages. Illustration K

6. Attach the magnetic cover to the roller cassette.

Filling the fresh water tank of the charging station

The fresh water tank in the device is primarily filled via the charging station. However, it is also possible to fill the fresh water tank manually, see Filling the fresh water tank.

ATTENTION

Risk of damage

Pouring hot water into the fresh water tank can lead to deformation of the plastic.

Do not pour hot water into fresh water tank.

Note

Always empty the waste water tank first before filling the fresh water tank.

1. Open the cover of the charging station.

Illustration L

1. Removing the fresh water tank.
2. Pull the tab on the cover of the fresh water tank and lift up the cover.
3. Fill the fresh water tank with cold or lukewarm tap water up to the MAX marking.
4. If necessary, add KÄRCHER detergent or care agent to the fresh water tank.

ATTENTION

Poor cleaning result due to incorrect use of the care agent

Over- or underdosing the detergent or care products can lead to poor cleaning results.

Pay attention to the dosage recommendations for the detergent or care agent.

Note

Do not use detergents from other manufacturers, as this may cause heavy foaming on the floor or in the waste water tank of the device.
In addition, foam may form during the first cleaning runs if there is still residue on the floor from previously used detergents from other manufacturers.
6. Close the cover.
7. Re-insert the fresh water tank into the charging station.
8. Close the cover of the charging station.

Filling the fresh water tank

It is possible to fill the fresh water tank in the device manually:

ATTENTION

Risk of damage

Pouring hot water into the fresh water tank can lead to deformation of the plastic.

Do not pour hot water into fresh water tank.

Note

Always empty the waste water tank first before filling the fresh water tank.

1. Remove the top cover. Illustration N
2. Grasp the fresh water tank by the recessed grips and remove it from the device.
3. Pull the rubber tab on the filling hole.
4. Fill the fresh water tank with cold or lukewarm tap water.
5. If necessary, add KÄRCHER detergent or care agent to the fresh water tank.

ATTENTION

Poor cleaning result due to incorrect use of the care agent

Over- or underdosing the detergent or care products can lead to poor cleaning results.

Pay attention to the dosage recommendations for the detergent or care agent.

Note

Do not use detergents from other manufacturers, as this may cause heavy foaming on the floor or in the waste water tank of the device.

In addition, foam may form during the first cleaning runs if there is still residue on the floor from previously used detergents from other manufacturers.

1. To prevent foaming on the floor or in the device, add Foam Stop to the fresh water tank in addition to the detergent during the first few cleaning runs. Repeat the procedure if necessary.
2. Close the rubber flap.
3. Insert the fresh water tank into the device.
4. Fit the top cover.

Insert dust bag

1. Open the cover of the charging station. Illustration M
2. Push the dust bag into the intake.
3. Close the cover of the charging station.

Operation

ATTENTION

Danger due to obstacles

Risk of damage

Before operating the cleaning robot, make sure that there are no obstacles on the floor, stairs or landings.

Preparing the environment

• Keep the floor free of objects lying around to ensure efficient cleaning. Obstacles require time-consuming cleaning because the cleaning robot has to drive around objects.
• Open the doors of the rooms that are to be cleaned.
• When operating the cleaning robot with the app: Carry out the configuration in the app so that the cleaning robot can clean according to individual cleaning requirements (no-go zones, different cleaning parameters, etc.), see chapter Settings in the app.

Settings

Settings on the robot

Cleaning can also be started from the cleaning robot without an app. The following commands can be executed using the buttons:

• Select cleaning mode via "Change cleaning mode" button, see Starting cleaning.
• Start cleaning via the On/Off/Pause button.
• Interrupt cleaning via the On/Off/Pause button.
• Return the cleaning robot manually to the charging station via the Home button.

The cleaning robot automatically returns to the charging station for recharging when it has completed a cleaning task or when the battery is too low during a cleaning process.

Settings in the app

The KÄRCHER Indoor Robots App offers the following main functions, among others:

• Step-by-step guide for configuration options
  • Map creation for rooms and several floors
• Setting of time schedules
  • Definition of no-go zones and virtual walls

• Notes on faults or malfunctions and the cleaning progress

• Setting of cleaning parameters such as amount of water, cleaning intensity, number of passes or carpet avoidance mode
  • Establishment of cleaning zones

• Activation/deactivation of the "Do not disturb" mode
• Calling up the live camera on the device
• Remote control of the device
  • FAQ with detailed troubleshooting guide

Switching on the cleaning robot

Note

Place the cleaning robot directly on the charging station if it cannot be switched on due to a too low charging state, see chapter Initial start-up.

1. Place the cleaning robot manually on the charging station and make sure that the battery terminals have a good contact.
   The cleaning robot switches on automatically and emits an acoustic signal.
   The LED bar pulsates white.

Note

Alternatively, the cleaning robot can also be switched on when it is not on the charging station:

1. Keep On/Off/Pause button pressed for 5 seconds. The cleaning robot switches on.

Illustration O

Operation without app

Starting cleaning

Note

Open the doors to all rooms that the cleaning robot is to clean and keep the floor free of objects lying around.

1. Press the On/Off/Pause button.

The cleaning robot gives an acoustic signal and first creates a map of the surroundings without cleaning. The LED buttons and the LED bar light up white.

When the map creation is finished, the cleaning robot returns to the charging station.

Note

Wait a few seconds until you press the On/Off/Pause button again so that the robot can save the map.

1. Select the desired cleaning mode.

a Select the cleaning mode via the "Change cleaning mode" button on the charging station.
Alternatively, the cleaning mode can be selected via the "Change cleaning mode" button on the device:

b Open the top cover.

c Select the desired cleaning mode via the "Change cleaning mode" button on the device.

Illustration P

1. Press the On/Off/Pause button.

The cleaning robot gives an acoustic signal and starts cleaning.

The LED buttons and the LED bar light up blue or yellow depending on the selected cleaning mode.

Note

When the waste water tank is full, the cleaning robot automatically returns to the charging station. The waste water is then pumped out in the charging station.

When the fresh water tank in the device is empty, the cleaning robot automatically returns to the charging station. The fresh water is then topped up in the charging station.

Depending on the setting in the app, the dust in the dust container is automatically vacuumed at regular intervals when it moves into the charging station.

Operation with the app

Creating a map

Note

Open the doors to all rooms that the cleaning robot is to clean and keep the floor free of objects lying around.

1. In the app, press the control panel "Start" and follow the steps indicated as needed.

The cleaning robot gives a audible signal and starts the map creation.

The LED buttons and the LED bar light up white.

When the map creation is finished, the cleaning robot returns to the charging station.

Configuring the robot in the app

Individual configurations of the map can be made in the app.

• Virtual walls and restricted areas prevent the cleaning robot from entering areas that should not be cleaned.
• With spot cleaning or cleaning zones, the robot can specifically clean the areas selected by the user once.
• With different cleaning modes, the cleaning intensity can be selected individually for each room depending on the type of floor or soiling (amount of water, number of passes per area, different roller speeds and robot travel speed, etc.)

Downloading the app is described in the chapter Connecting cleaning robots with WLAN and App.

1. Follow the step-by-step instructions in the App.

Starting cleaning

1. Select the desired map in the app and start cleaning according to the individual configuration.

Note

When the waste water tank is full, the cleaning robot automatically returns to the charging station. The waste water is then pumped out in the charging station.

When the fresh water tank in the device is empty, the cleaning robot automatically returns to the charging station. The fresh water is then topped up in the charging station.

Depending on the setting in the app, the dust in the dust container is automatically vacuumed at regular intervals when it moves into the charging station.

Interrupting cleaning

Interrupting cleaning on the device

1. Press any button during cleaning.

The cleaning robot stops.

The LED buttons pulse blue or yellow (depending on the selected cleaning mode).

The LED bar pulses blue or yellow (depending on the selected cleaning mode).

1. Press the On/Off/Pause button.

Cleaning continues.

The LED buttons light up blue or yellow (depending on the selected cleaning mode).

The LED bar lights up blue or yellow (depending on the selected cleaning mode).

Interrupting cleaning in the app

1. In the app, press the control panel "Break".

The cleaning robot stops.

The LED buttons pulse blue or yellow (depending on the selected cleaning mode).

The LED bar pulses blue or yellow (depending on the selected cleaning mode).

1. In the app, press the control panel "Start".

Cleaning continues.

The LED buttons light up blue or yellow (depending on the selected cleaning mode).

The LED bar lights up blue or yellow (depending on the selected cleaning mode).

Battery level indicator

Note

If the battery is empty, the cleaning robot automatically returns to the charging station to recharge the battery. Optical signals warn of a flat battery:

- The LED buttons pulsate red when the battery is empty and needs to be recharged.

Note

If the cleaning robot didn't complete the cleaning before, it will resume cleaning once the battery is recharged.

Manually sending the cleaning robot for recharging

Manually sending the cleaning robot for recharging

1. If the robot is currently performing a cleaning run, press any button.

The cleaning robot stops.

The LED buttons pulse blue or yellow (depending on the selected cleaning mode).

The LED bar pulses blue or yellow (depending on the selected cleaning mode).

1. Press the Home button.

The cleaning is cancelled.

The cleaning robot moves to the charging station for recharging.

As soon as the cleaning robot is connected to the charging station, the LED buttons pulsate green.

The cleaning robot automatically returns to the charging station for recharging when it has completed a cleaning task or when the battery is too low during a cleaning process.

Manually sending the cleaning robot for recharging via the app

1. If the robot is currently performing a cleaning run, press the control panel "Break" in the app.
   The cleaning robot stops.
   The LED buttons pulse blue or yellow (depending on the selected cleaning mode).
   The LED bar pulses blue or yellow (depending on the selected cleaning mode).

2. In the app, press the control panel "Charge".

The cleaning is cancelled.

The cleaning robot moves to the charging station for recharging.

As soon as the cleaning robot is connected to the charging station, the LED buttons pulsate green.

The cleaning robot automatically returns to the charging station for recharging when it has completed a cleaning task or when the battery is too low during a cleaning process.

Emptying the waste water tank

When the waste water tank is full, the LED buttons and the LED bar pulsate red and the cleaning robot returns to the charging station.

The waste water is automatically extracted from the cleaning robot in the charging station.

Manually emptying the waste water tank:

1. Remove the waste water tank, see Remove waste water tank.

2. Pull the opening lever on the waste water tank upwards and lift the cover of the waste water tank. Illustration Q

3. Empty the waste water tank. In case of stubborn dirt, rinse the waste water tank with fresh water or clean it with the cleaning brush.

Illustration R

1. Close the cover of the waste water tank.
2. Insert the waste water tank, see Fitting the waste water tank.
3. To continue cleaning, press the On/Off/Pause button button.

Emptying the dust container

Depending on the setting in the app, the dust in the dust container is automatically vacuumed at regular intervals when it moves into the charging station.

Manually emptying the dust container:

1. Remove the top cover.
2. Press the clip and grip the dust container by the handle grooves to remove it from the device.

Illustration U

1. Fold the flap down.

Illustration V

1. Empty the dust container.
2. Fold the flap upwards until it audibly latches into place.
3. Insert the dust container.
4. To continue cleaning, press the On/Off/Pause button button.

Refilling the cleaning fluid

When the fresh water tank is empty, the LED buttons and the LED bar pulsate red and the cleaning robot returns to the charging station.

The fresh water tank in the cleaning robot is filled automatically in the charging station.

Note

If the fresh water tank in the charging station is empty, fill the fresh water tank, see Filling the fresh water tank of the charging station.

Manually refilling the cleaning fluid:

1. Fill the fresh water tank in the device (see chapter Filling the fresh water tank).

Switching off the device

Note

The cleaning robot cannot be switched off when it is on the charging station.

1. Press and hold the On/Off/Pause button 5 seconds. The LED buttons and the LED bar go out. The cleaning robot switches off.
2. Empty and clean the waste water tank in the device, see Cleaning the waste water tank.
3. Empty the waste water tank in the charging station and rinse with fresh water.
4. Empty and clean the dust container, see Cleaning the dust container.
5. Clean the Scraper unit with the hair comb, see chapter Cleaning the roller cassette and scraper unit with hair comb.
6. Clean the cleaning brush, see Cleaning the cleaning brush.

Reseting the WLAN connection

If you switch to a new router or change your WLAN password, you must update the cleaning robot's WLAN connection.

Note

2.4 GHz and 5-GHz WLAN networks are supported.

1. Switch on the cleaning robot, see chapter Switching on the cleaning robot.
2. Press the On/Off/Pause button and the Home button simultaneously for 3 seconds until an acoustic signal sounds.

Restoring the factory settings

1. Press the Home button for 5 seconds until a signal sounds.
2. Press the Home button again for 5 seconds until a signal sounds.

The factory settings are restored.

Transport

Where possible, always transport or return the device in the original packaging. Please contact our Service Department if the original packaging is not available.

Safety instructions for transporting

The lithium-ion battery is subject to the requirements of dangerous goods regulations.

An undamaged and functional battery pack can be transported by the user in public traffic areas without any further restrictions.

When shipping by third parties (transport companies), special requirements for packaging and labelling must be observed.

Observe the national regulations.

Storage

ATTENTION

Odour development due to moisture

Unpleasant odours can develop if the device contains liquids/moist dirt when stored.

Completely empty the fresh water tank and waste water tank before storing the device.

Clean the roller cassette.

Use the cleaning tool to remove hair and dirt particles from the scraper unit with hair comb.

Allow the cleaned roller to air dry.

Do not place the wet roller in an closed cupboard to dry.

ATTENTION

Material damage

Incorrect storage can lead to damage to the device.

Do not place any objects on the cleaning robot.

Do not store the device upside down.

Store the cleaning robot fully charged and switched off in a cool and dry place.

Note

To avoid a deep discharge of the battery, fully recharge the cleaning robot after 5 months at the latest.

Care and service

Changing the dust bag

1. Open the cover of the charging station.
2. Pull the full dust bag upwards by the flap to remove the bag. This closes the opening of the dust bag.
3. If necessary, clean the interior space of the charging station and the motor protection filter, see Cleaning the motor protection filter.
4. Unfold the new dust bag and push it into the support from above.

Illustration M

1. Close the cover of the charging station.

Cleaning the motor protection filter

1. Open the cover of the charging station.

Illustration W

1. Pull the dust bag upwards by the flap to remove the bag. This closes the opening of the dust bag.
2. Remove the motor protection filter.
3. Clean the motor protection filter under running water.
4. Allow the motor protection filter to dry.
5. Insert the motor protection filter into the charging station.
6. Insert the dust bag, see Insert dust bag.
7. Close the cover of the charging station.

Cleaning the charging station waste water tank

ATTENTION

Odour development due to moisture in the waste water tank

Unpleasant odours can develop if the waste water tank contains liquids/moist dirt when stored.

Empty the waste water tank completely.

Clean the waste water tank regularly.

1. Open the cover of the charging station.
2. Remove the waste water tank.
3. Pull the tab on the cover of the waste water tank and lift up the cover.
4. Empty the waste water tank. In case of stubborn dirt, rinse the waste water tank with fresh water or clean it with the cleaning brush.
5. Close the cover of the waste water tank.
6. Insert the waste water tank into the charging station.
7. Close the cover of the charging station.

Cleaning the sensors

Clean the sensors at least monthly. Always clean the sensors immediately if they become dirty.

Illustration S

Illustration T

1. Wipe the sensors with a soft cloth.

Cleaning the contacts

Clean the contacts on the device and the waste water tank at least once a month. Always clean the contacts immediately if they become dirty.

1. Remove the waste water tank, see Remove waste water tank.
2. Wipe the contacts on the device and the waste water tank with a soft cloth.

Illustration X

Cleaning the waste water tank

ATTENTION

Adhering dirt deposits

Adhering dirt deposits can damage the device in the long term.

Clean the waste water tank regularly.

For information on the waste water tank cleaning and emptying procedure, see chapter Emptying the waste water tank.

Cleaning the cleaning roller in the charging station

Note

The cleaning roller can only be cleaned in the charging station when the cleaning robot is in the charging station.

Note

The cleaning rollers are automatically cleaned in the charging station after each completed cleaning process.

Clean the cleaning rollers manually in the charging station:

1. Press the "Start self-cleaning" button.

Cleaning the cleaning roller

ATTENTION

Detergent residue in the roller

Foaming

Wash the roller under running water or clean the roller in a washing machine each time after using the device.

ATTENTION

Damage caused by washing the cleaning roller with fabric softener or using a tumble dryer

Damage to the microfibres

Do not use fabric softener when cleaning in a washing machine.

Do not dry the roller in a tumble dryer.

ATTENTION

Material damage due to loose roller

This may damage the washing machine.

Place the roller in a laundry net and load the washing machine with extra laundry.

1. Remove the magnetic cover on the roller cassette. Illustration H

2. Press the unlocking button on the roller cassette. Illustration Y

The roller cassette detaches from the cleaning robot.

1. Remove the roller cassette from the cleaning robot.

2. Fold up the scraper unit.

3. Remove the cleaning roller from the roller cassette. Illustration Z

4. Clean the cleaning roller under running water or wash it in the washing machine at max. 60 °C. Illustration AA

5. Clean the roller drive with a moist cloth.

6. Allow the cleaning roller to air dry.

Cleaning the roller cassette and scraper unit with hair comb

ATTENTION

Damage due to cleaning the scraper unit in a dishwasher

The washing process can distort the scraper unit and it will no longer press on the roller correctly. This worsens the cleaning result.

Do not clean the scraper unit in a dishwasher but rather under running water.

ATTENTION

Adhering dirt deposits

Adhering dirt deposits can damage the device in the long term.

It is recommended to clean the device completely after each application.

ATTENTION

Adhering dirt deposits

Adhering dirt deposits can damage the device in the long term.

Clean the scraper unit regularly with the cleaning tool.

1. Remove the magnetic cover on the roller cassette. Illustration H

2. Press the roller cassette unlocking button. Illustration Y

The roller cassette detaches from the cleaning robot.

1. Remove the roller cassette from the cleaning robot.

2. Fold up the Scraper unit.

3. Remove the cleaning roller from the roller cassette. Illustration Z

4. Clean the Scraper unit under running water.

Note

Do not clean the Scraper unit and the roller cassette in the dishwasher, as this may damage the components.

1. Remove stubborn dirt with the cleaning tool. Illustration AB

2. Fold down the Scraper unit.

3. Pay attention to the cassette guide and push the roller cassette into the cleaning robot until it audibly engages.

Illustration K

1. Attach the magnetic cover to the roller cassette.

Cleaning the dust container

1. Empty the dust container.

ATTENTION

Damage to electronic components

Do not clean the dust container with water.

1. Clean the dust container with the cleaning tool supplied.

Illustration AC

1. Fold the flap upwards until it audibly latches into place.

2. Insert the dust container.

Cleaning the filter

We recommend cleaning the filters regularly. This prevents them from becoming clogged.

1. Remove the top cover.

2. Press the clip and grip the dust container by the handle grooves to remove it from the device.

Illustration U

1. Press the clamp.

Illustration AD

1. Open the cover.

2. Remove the filter.

3. Clean the filter under running water with the cleaning tool supplied.

Illustration AE

1. Allow the filter to dry completely.

2. Press the filter into position.

3. Close the cover of the dust container.

4. Insert the dust container.

Cleaning the cleaning brush

1. Turn the cleaning robot upside down.

Note

Make sure to empty or remove the fresh and waste water tank from the device beforehand.

1. Press the clamps on the brush cover together. Illustration AF

2. Remove the brush cover.

3. Remove the cleaning brush. Illustration AG

4. Clean the cleaning brush with the cleaning tool supplied.

5. Insert the cleaning brush.

6. Fit the brush cover and press it down until it audibly latches into place.

Cleaning the wheels

Dirt particles (such as sand, etc.) can get stuck on the running surface and then damage sensitive, smooth floor surfaces.

1. Clean the running surface of the wheels with a damp cloth.

Cleaning the bottom of the device

ATTENTION

Adhering dirt deposits

Adhering dirt deposits can damage the device in the long term.

It is recommended to clean the device completely after each application.

1. Remove the waste water tank, see Remove waste water tank.

2. Press the roller cassette unlocking button.

Illustration Y

The roller cassette detaches from the cleaning robot.

1. Remove the roller cassette from the cleaning robot.

2. Clean the bottom of the device and the exposed inner surfaces as well as the visible contacts and sensors with a damp cloth.

3. Pay attention to the cassette guide and push the roller cassette into the cleaning robot until it audibly engages.

Illustration K

1. Insert the waste water tank, see Fitting the waste water tank.

Cleaning and care agents

ATTENTION

Use of unsuitable detergents and care agents

The use of unsuitable detergents and care agents can damage the device and loss of eligibility for warranty claims.

Use only KÄRCHER detergents.

Take care to ensure the correct dosage.

Note

Use KÄRCHER detergent or care agents for floor cleaning as necessary.

- Observe the manufacturer's dosing quantity recommendations when dosing with detergent or care agents.

- To prevent foaming, fill the fresh water tank with water first and the add the detergent or care agent.

- To prevent the tank from overflowing, be sure to leave enough space for the detergent or care agent when filling with water.

Replacing the cleaning roller

A worn cleaning roller can worsen the cleaning result.

1. Check the cleaning roller regularly for wear and replace if necessary.

Clean the water filter of the charging station

1. Open the storage compartment for the roller on the charging station.

Illustration AH

1. Rotate the bayonet connector of the water filter and pull out the water filter.

2. Clean the water filter under running water.

3. Re-insert the water filter into the charging station.

4. Close the storage compartment for the roller.

Cleaning the liquid sensor

The charging station is equipped with sensors that trigger an error message if there is too much moisture on the station.

If the error message occurs, the liquid must be removed:

1. Remove the loading ramp from the charging station and remove the liquid. Illustration AI

2. Clean the humidity sensors with a cloth.

3. Remove the waste water tank, see Remove waste water tank.

4. Pull the opening lever on the waste water tank upwards and lift the cover of the waste water tank. Illustration Q

5. Clean the inside and outside of the waste water tank water inlet.

6. Close the cover of the waste water tank.

7. Insert the waste water tank into the device, see Fitting the waste water tank.

8. Clean the roller cassette, see Cleaning the roller cassette and scraper unit with hair comb.

Troubleshooting guide

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in

doubt, or in the case of malfunctions not mentioned here, please contact your authorized Customer Service.

Fault Cause Rectification
Battery does not charge	The charging contacts are dirty.	1. Wipe the charging contacts on both the charging station and the cleaning robot with a dry cloth.
	Ambient temperature below 0 °C or above 35 °C.	1. Use the cleaning robot at temperatures above 0 °C and below 35 °C.
	The mains cable of the charging station is not plugged in.	1. Plug in the mains cable of the charging sta-tion.
The cleaning robot is not returning to the charging station	The battery is empty. 1. Manually place the cleaning robot on the charging station and let it charge completely.
	The cleaning robot is too far away from the charging station.	1. Move the cleaning robot closer to the charging station.2. Manually place the cleaning robot on the charging station.
	Not enough space around the charging station.	1. Ensure that there is sufficient space around the charging station, see chapter Setting up the charging station.
	There are too many obstacles around the charging station.	1. Place the charging station in a more open area, see chapter Setting up the charging station.
	The cleaning robot remaps its environment when it has been moved over a longer distance.	1. Manually place the cleaning robot on the charging station.
	The cleaning robot was not started from the charging station. In this case, it only returns to the place from which it was started.	1. Manually place the cleaning robot on the charging station.
	The mains cable of the charging station is not plugged in.	1. Plug in the mains cable of the charging station.
Dust suction does not start or does not work properly	The cleaning robot is not positioned correctly on the charging station.	1. Manually place the cleaning robot on the charging station.
	The dust bag is full.The LED on the intake for the dust bag lights up red.	1. Change the dust bag (see Changing the dust bag).
	There is no dust bag or it is installed incorrectly.	1. Insert the dust bag or check that it is installed properly.
	The cover of the charging station is open.	1. Close the cover of the charging station.
The LED buttons and the LED bar on the device pulsate red	The fresh water tank is empty. 1. Fill the fresh water tank.
	The waste water tank is full. 1. Empty the waste water tank.
The LED buttons pulse red and the LED bar on the device does not light up	The battery is empty. 1. Charge the battery.
The LED buttons flash red and the LED bar on the device does not light up	The dust container is not located in the device.	1. Insert the dust container.
	The battery charge is less than 20%. The device cannot start cleaning.	1. Charge the battery.
The LED on the intake for the dust bag in the charging station lights up red	There is no dust bag in the charging station.	1. Insert a dust bag.
The LED on the fresh water tank in the charging station lights up red	The fresh water tank is empty. 1. Fill the fresh water tank.
	The fresh water tank is not located in the device.	1. Insert the fresh water tank.
The LED on the fresh water tank in the charging station lights up red even though the fresh water tank is full	The water filter for the fresh water supply from the charging station to the device is blocked.	1. Clean the water filter (see Clean the water filter of the charging station).2. If the problem persists, replace the water filter.
The LED on the waste water tank in the charging station lights up red	The waste water tank is full. 1. Empty the waste water tank.
	The waste water tank is not located in the device.	1. Insert the waste water tank.

Customer Service department

If the malfunction cannot be corrected, the device must be checked by the Customer Service department.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

(See overleaf for the address)

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

EU Declaration of Conformity

Device Type	Frequency band, MHz	Power, max. EIRP, mW
RVF 7 W	LAN 2400-2483.5 100

Alfred Kärcher SE & Co. KG hereby declares that the radio device type Robo Cleaner complies with the 2014/53/EU directive. The full text of the EU Declaration of Conformity can be found at www.kaercher.com/RVF7.

Declaration of Conformity

Device Type	Frequency band, MHz	Power, max. EIRP, mW
RVF 7 W	LAN 2400-2483.5 100

Alfred Kärcher SE & Co. KG hereby declares that the radio device type Robo Cleaner complies with the UK regulation S.I. 2017/1206 (as amended). The full text of the Declaration of Conformity can be found at www.kaercher.com/RVF7.

Technical data

		RCF 7Comfort
Cleaning robot
Rated power W 60
Battery pack type Li-ION
Battery capacity mAh 4800
Operating time when battery is ful- min 120ly charged in normal operation
Surface performance m	^2/h 45
Suction performance (Boost mode / Standard mode)	Pa	10000 / 2000
Charging time (8 % to 100 % / 0 % to 100 %)	min 230 / 285
Wireless connections		IEEE802.11b/g/n 2.4GHz & 5 GHz
Frequency	MHz 2400-2483.5
Sound pressure level	dB(A)	<67

		RCF 7Comfort
Fresh water tank capacity	ml	300
Waste water tank capacity	ml	130
Dry dirt	ml	250
Weight	kg	5,6
Charging station
Nominal power consumption (suction/charging process)	W	650/30
Self-cleaning duration	Seconds	90-240
Fresh water tank capacity	l	3,25
Waste water tank capacity	l	2,5
Dry dirt	l	4
Weight	kg	9,3
Length x width x height	mm	450x400x520
Sound pressure level	dB(A)	82

Subject to technical modifications.

Contenu

Download on the App Store

⑰ Foam Stop 30 ml (2 x)

18 RM 536 500 ml

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

• Google Play™ y Android™ son marcas o marcas registradas de Google Inc.
• Apple ^® y App Store ^® son marcas o marcas registradas de Apple Inc.

Download on the App Store

Download on the App Store

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

⑰ Foam Stop 30 ml (2 x)

18 RM 536 500 ml

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

⑰ Foam Stop 30 ml (2 x)

18 RM 536 500 ml

⑲Av/På-/pause-knapp

20 «Home»-knapp

213D-sensor med kamera

22Veggsensor

23 LED-list til statusvisning

24 Toppdeksel

25 Ferskvannsinntak

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

Rengjør rullekassetten.

Download on the App Store

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

⑰ Foam Stop 30 ml (2 x)

18 RM 536 500 ml

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

⑰ Foam Stop 30 ml (2 x)

⑱ RM 536 500 ml

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

⑰ Foam Stop 30 ml (2 x)

⑱ RM 536 500 ml

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

⑰ Foam Stop 30 ml (2 x)

18 RM 536 500 ml

19 Tipka za vklop/izklop/premor

20 Tipka Domov

②13D-senzor s kamera

QR code image containing encoded data, no visible human-readable text

Download on the

App Store

QR code image containing encoded data, no visible human-readable text

• Google Play™ in Android™ sta blagovni znamki ali registrirani blagovni znamki družbe Google Inc.
• Apple ^® in App Store ^® sta blagovni znamki ali registrirani blagovni znamki družbe Apple Inc.

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

• Google Play™ i Android™ su marke ili registrovani zaštitni znaci kompanije Google Inc.
• Apple ^® i App Store ^® su marke ili registrovani zaštitni znaci kompanije Apple Inc.

Povezivanje robota za čišćenje sa KÄRCHER Indoor Robots aplikacijom i WLAN mrežom:

1. Preuzmite KÄRCHER Indoor Robots aplikaciju preko prodavnice aplikacija Google Play Store.
2. Otvorite KÄRCHER Indoor Robots aplikaciju.
3. Kreirajte nalog (ako još niste registrovani).
4. Dodajte željenog robota za čišćenje.
5. Sledite korake u uputstvu za aplikaciju.

Puštanje u pogon

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

Download on the App Store

QR code image containing encoded data, no visible human-readable text

.www.kaercher.com/RVF7

اليانيات الفنية

QR code image containing encoded data, no visible human-readable text

QR code image containing encoded data, no visible human-readable text

الأ Ortاع الخاصة

وضع Sesكون

Symbol of a trash bin with crossed lines indicating no waste or restriction, and a solid black rectangle below (no text or labels)

QR code image containing encoded data, no visible human-readable text

Scan QR Code for download and easy product registration in Home & Garden App or website.

karcher.com/register

KARCHER BRING BACK THE WOW LIKE AN EXPERT. CREATE ASSIST Login | CONTINUE AS QUEST WHERE YOU ARE LOWER THE ISSUE IS IN EYES AND I KNOW FOR

EN – Download the Home & Garden App to register your device for full support in cleaning.

■ Control of smart products
■ Application tips & expert knowledge
■ Product information, overview of accessories and operating instructions
■ Support and service contact
■ Online shop – exclusive offers and much more

karcher.com/dealersearch

Alfred Kärcher SE & Co, KG

Alfred-Kürcher-Str. 28-40

71364 Winnenden [Germany]